Turn on RED/GREEN LED if PASS/FAIL

Similar Questions

• LED red/green user guide

  Where can I find a description of the red/green LED at the top of the phome left of the slot of the ear?

  good here.

• a numerical limit several test, the individual results of pass/fail there?

  I want to communicate the pass/fail status to my custom user interface so that I can color components red/green they spend and fail.  I intend to send the State of pass/fail with an ID corresponding to the element using UIMessaging.  The UImessage is sent by the sequencePostStep callback.

  Send individual pass/fail status is simple enough forward (step.result.status) for all stages except test multiple numerical limit.  Is there a way to get the information of pass/fail individual for each item in a test of numerical limit multiple?  Individual information is available in the report.  Could it be pulled from the [ReportText]?

  Hi Dillon,

  You can get multiple results in a limit test using Step.Result.Measurement ["Measurement 0"]. Status, which will give each individual measurement result.  You can assign the results of the 4 comparisons by using something like this:

  Locals.multstring [0] = Step.Result.Measurement [0]. Status,
  Locals.multstring [1] = Step.Result.Measurement [1]. Status,
  Locals.multstring [2] = Step.Result.Measurement [2]. Status,
  Locals.multstring [3] = Step.Result.Measurement [3]. Status

  If the chain is too great for practice, you can browse using a loop for.  Let me know if you have any other questions!

• Satellite Pro C660 not turn on - green LED only

  Sorry if this is a piece of cake for you.

  Laptop was overheating. I usually just unscrew a few screws, dig up the lint on the fins, rebuild and everything is ok.

  BIG mistake: I hibernated computer instead of turn off, battery on the left and then disassembled (don't ask me how or why I did it because I don't know)

  A lot of fluff out of fins.

  Reconstruction, button / stop only lights up green LED, screen remains dead, no audio noise, no beeps.

  Took part 3 times now and rebuilt, but can't find a problem.

  Drive in a caddy and saved elsewhere,

  No idea what is going on, or if the laptop is repairable? I feel such a fool.

  Thanks if you can help

  The laptop supports HARD SATA 2.5 drive. Laptops more (no matter who the manufacturer was) supports SATA 2.5 HARD disk and where the HARD drive is OK, you should be able to use it

  but the preinstalled system contains the drivers and the drivers would probably be not compatible with the new laptop.

  That is why it s recommended to move the data to the HARD drive on another source (another 2nd HDD, USB flash stick of memory, etc.) and then do a fresh install of the OS.

• indicators red green and yellow are grey, I have accidentally uninstalled something in the "login items", but don't know what or how to replace. Thank you!

  indicators red green and yellow are grey, I have accidentally uninstalled something in the "login items", but don't know what or how to replace. Thank you!

  You have probably changed the OS X. go theme color in Preferences-> general systemand pass ' appearance: " "Blue ".

• After 32RL933 the firmware update won't start no - green LED lights

  After an update of the firmware via wifi and use the TV for a few hours, when I changed the Source, the TV goes black and reboot, right now the TV is always black, green LED flashing and the screen turns black.

  I think it's a firmware issue, I tried to pull the plug and put back in operation and does not. I have donwloaded a rl933_748304.bin firmware on the site, loaded onto usb and plugged into the TV and does not work, so I think I need a "auto-install" firmware that runs at the start of the TV instead a normal firmware.

  I've read that a lot of people have this problem, I hope that you could give me support.

  Thanks in advance and sorry for my English.

  Try this:
  Turning the TV off. Wait 30 seconds, then press power button.
  Then OFF it again. Unplug the power cable and LAN cable.
  Reconnect the cable LAN and power ON the TV.
  Now reset the TV.
  GO to the system configuration menu, select TV point Reset and press OK to select.

• HP Omni 120-1050xt: screen goes to red, green, blue, white, black after upgrade to Windows 10

  When the PC is idle, the screen turns red, green, blue, white, black, and every time I need to turn off the machine. He said "best driver for your device is already installed" - Intel HD Graphics. I tried to uninstall, install.

  Greetings,

  HP not support your PC when you run Win 10.

  I suggest that use the "Go Back " process win 10 ASAP.

  If this is not possible because of your graphics problems you'll have to do a restore to factory HP.

  I can help you more with this if you wish.

  If the upgrade was forced on you there are ways to stop the involuntary update.

  Let me know if you need further assistance.

  Jay

• Edge s430 green LED power but will not start

  Hello

  This morning I was browsing the internet, using Skype on my s430 to edge with no problems. The battery got low so I plugged on the power supply, plugged my phone into the usb port to recharge and it left while I got breakfast. When I returned the laptop is not turning on when I open the lid.

  I waited and hit a few keys on the keyboard (it usually does). But nothing... tried pressing and holding the power button / stop for 30 seconds, nothing - no lights, no fans.

  The battery is sealed inside, so I can't do much - I tried unplugging the AC, by pressing the power button 15 times second intervals, then hold for 30 seconds, but no change - no lights, no fans.

  When I plug in the adapter, the Green led lights solid - not flashing do not or anything like that.

  Edge s430 - stock i7 computer 3364cto laptop.

  Any help appreciated.

  Fixed in the case where someone else shows - laptop computer Unplugged, unplugged the wall charger - left both like this for 24 hours all reconnected and tried and it worked - no idea what was wrong but everything works fine now.

• My Sony Vaio model PCG - 61611L Green LED lights up but nothing happens

  When I turn on my Sony Vaio model PCG - 61611L, the Green led lights up, but nothing goes well. The laptop is 2010 and is never abused, so I don't know what happened. It just started this making times and now I can't turn it on at all. Any suggestions?

  shoemanfl,

  It seems that you have no POST issue.  Is it the caplock/numlock light up when you press it?  Did you try to connect to an external monitor to see if it's a matter of display dim?  If this is no a POSITION, try reinstalling the ram or using one at a time... you can also remove the optical drive and hard drive to see if you can start any found nail system.  If you can not always unity would require service...

• BlackBerry Smartphones green LED when the load

  Hi all

  I wonder if you can help me, I charge my phone in its cradle every night in the bedroom. I had to turn in bedside mode when charging. Problem is that if I keep the phone then I get notification sounds when you receive emails etc. If I turn off the phone and docked I get the Green solid light that lights up the room when completely loaded. So any info on the following:

  1. disable the Green LED when loading?

  2. can I configure bedside mode to enter in silence?

  3. can I plan a silent mode to switch at some point?

  Thanks in advance

  Creeky

  I have my bedside mode configured to turn off the wireless radio. In this way, I don't get the emails until I turn radio wireless (at the exit of the bedside mode).

  Another thing to do, is do not use the charging base, but using the cable plug and return your phone so that the light is directed downwards and not upwards.

• BlackBerry Smartphones solid green LED ALWAYS

  Hey, it's really bugging me. I have my indicator of coverage off the coast, I have not new messages/calls/something like that, but there is a solid green LED on my Storm all the time. He has served for the past 3 days. I did a battery pull, and back in the Green LED came on immediately when I put the battery. I let my battery to fully discharge and then recharge completely, so my battery level was anywhere from 0% to 100% and the Green LED was on all the time. I know there was another thread on this forum about a flashing green LED, but mine remains STRONG, so I was hoping that someone would be able to help. Any ideas?

  Well, I had the light turns off. I think that the Green LED continuously when you have a load of 100% and it is still on the charger, so I left it completely load, then took it off the charger and it must have fixed.

• 2407WFP Power Save mode - only flashes red, green, blue, black, white, repeat

  Hello

  My 2407WFP won't go into fashion, economy of energy even when the computer is off. (He used to do this properly).

  When the computer sleeps, turned off, or when the cable is disconnected, the monitor will be full-screen flash red, green, blue, black, white, then go to sleep for about 5 seconds. Then, he repeats this sequence instead of going right to sleep/wake.

  Different computers, different cables, no change. Is it possible that this is somehow the self-test mode?

  Thank you.

  * Turn off the monitor
  * Press and hold the plus button and menu button at the same time, and then click the power button
  * Once back on, press the "-" and the service menu should appear
  * Press the button "-". The Service Menu should appear
  * Scroll down to Burnin Mode using the button ""
  * Press the Menu button to turn on this setting
  * Press the button "-" to turn it Off (it should be blue when selected)
  * Press the "+" to highlight the Menu exit
  * Press the Menu key

• HP DC7600 - will not turn on, red light and beeps.

  Hello

  In my office, that we just moved all the furniture around, all workstations have been displaced and worked fine before the move.

  One of them now won't start, its a flat Tower HP DC7600. She now does when you press the power button, is flashing a red light and a beep 5 times. Then do the same thing again and again.

  Any idea as to what could be the problem?

  Thank you very much

  Ben

  It sort!

  Red Power LED blinks 5 times, once every second, followed by a pause of two seconds. Beeps stop after the fifth iteration but LEDs continue until the problem is resolved. Out of memory error video pre 5. 1 reinstall the DIMMs. Turn on the system. 2. replace the DIMM one by one to isolate the faulty module. 3. replace the third-party memory by memory HP. 4. replace the motherboard.

  Thanks for looking anyway!

  Ben

• pass fails with a missing resource pool alert

  Hi, I have a server dell power edge r510, with ESXi 5.0 is installed in it.

  in one of the virtual machines within this server, I installed Vcenter (I think that it is Version 5.1) everything was stable until the vcenter database gets 10 GB and crashed and I couldn't fix it. So I installed a new windows with vcenter 5.5 inside vps. and for this new vcenter reconnected to the server. so, I've reconfigured resource pools and VPS users again in this new vcenter.

  Watch ESXi host now as does not not to the vcenter. but all virtual machines inside the esxi server work without problems.  I can't reconnect to the host in vcenter, and I can't connect directly to the ESXi via vsphere client and root password.

  but I can log on to the esxi via ssh or console.

  from the console, I restarted the management services, but it does not help.

  the SSH, I ran the following commands:

  status /etc/init.d/vpxa #.

  vpxa is running

  status /etc/init.d/hostd #.

  pass is not running.

  When I restart pass, it is said has started, but after a few minutes still pass fails.

  l # /etc/init.d/hostd restart

  Watchdog - pass: PID of the file/var/run/vmware/watchdog-hostd. PID does not exist

  Watchdog - pass: impossible to end guard dog: no monitoring running processes to pass

  SH: you must specify which kill

  [421281] Begin ' pass ++ min = 0, swap, group = pass etc/vmware/hostd/config.xml', min-uptime = 60, max-fast-failures = 1, max-total-failures = 1000000, bg_pid_file = "

  pass began.

  **********************************************************

  status /etc/init.d/hostd #.

  pass is running.

  ***************************************************************

  but I can't use all the controls of esxcli.

  List of the allowedip of esxcli network firewall ruleset

  Connect to locahost failed: connection failure

  ************************************************************

  status /etc/init.d/hostd #.

  pass is not running.

  ***************************************************************

  I searched the problem on localhost, Ko, said check the CPU usage is below 90%, which is good in my esxtop, then says check network ports and pings, they were right, too, said to check/etc/hosts to 127.0.0.1 localhost entry and checking /etc/resolv.conf and they were right too. as I can ping localhost and localhost nslookup returns 127.0.0.1

  then I started reading the server logs and found this error output of vm-support: hostd.log

  [cntos58-64-Farzin - 105.vmx'] could not get the parameters of resource for a virtual machine under tension

  Award of the VM ' / vmfs/volumes/.../cntos58-64-Farzin-105.vmx' to the root resource pool - configured pool 'pool11' does not exist

  SysInfo error on return operation State: verification of Admission of cpu resource failure. See the VMkernel detailed error information log

  cntos58-64-Farzin - 105.vmx: vim.fault.InsufficientCpuResourcesFault

  *************************************************************************

  How can I change the list of resources of the VM to ssh when esxcli do not work?

  I am facing this problem recently, almost all the 5 days the server will respond is not in vcenter, restart the entire esxi server can solve the problem but it apears again.

  I think that resource in vcenter pools doesn't sync properly with the configuration of esxi, as when I connect to the server directly with root/vshpere it shows different configuration than what I see in vcenter!

  and I can't upgrade esxi host because there are about 10 VPSes important and stable running on this server which is my main server and I can not have time on this server or migrate virtual machines to a different server/IPs.

  because I'm not sure of the compatibility of the versions of drivers/bios nic with ESXi 5.5 and I fear that if I update the ESXi from 5.0 to 5.5 I face other questions strangers/downtime.

  I had the server up and running again, by editing this file: /etc/vmware/hostd/pools.xml

  then I found the VPS with id of the pool of resources 11 evil, changed for another pool of resources as the other virtual machines.

  2014 07-29 T 08: 38:52.64965Z

  2

  pool366

  and then made a

  restart the /etc/init.d/hostd

  all started working again without restarting the whole esxi server and turn off virtual machines, I have searched for about 1 day to solve this simple thing!

  even once when I made a few changes in the vcenter, and then restarted resource pool settings move it in ssh, it fails under vcenter changed the VM resource for a bad configuration pool.

  so I changed the resource pool manually xml and restarted spend, while vcenter can connect to the esxi host.

  then vcenter, again removed all the resource pools and created new resource pools. and this question of time is set.

  There was some resource pool configuration that was imported from esxi host to vcenter which was no longer available and has not been deleted in syncronizations between esxi and vcenter when changed resource pools. and the list of the missing resources caused problems.

• Captivate 5.5 Actions preferences Pass/Fail Quiz

  Is there a good explanation anywhere from the Pass/Fail actions in Captivate, when we want to use an action and combinations of actions can or should be used?

  No matter what I choose for stocks, as well in passing and failing grade, disable, enable, increment and Deincrement are grey. If they are still grayed out, what they are?

  I looked in the Help menu of Adobe, but as often happens, the information is too vague and high-level in the Help menu for any real understanding.

  Enable and disable actions are dimmed if there is no suitable interactive object (for example, buttons or the clickboxes) on the screen that can be enabled or disabled by the action.

  If you want to see toggle appear listed. Add a button to the stage, then try ON Slide enter this slide to turn off the control knob.