Two interconnected WRT610N

Similar Questions

• To access the administration page remotely of two interconnected WRT610N?

  I'm sure that I've done it before, but I can't remember how. Let's say I have TWO WRT610N which are interconnected...

  Router 1

  IP: 192.168.1.1

  Connected to the modem (Internet)

  Remote 8881 value port

  DHCP enabled

  Gateway mode

  Router 2

  IP: 192.168.1.2

  1 LAN port connected to the LAN port of Router 1 2

  8882 value remote port

  DHCP disabled

  Gateway mode

  Now, I want to be able to type the WAN IP address that connects to the Router 1 and be able to access the Router 1 or router 2 admin page.

  Thus, for example, say that my WAN IP is 68.96.215.121

  Router 1

  68.96.215.121:8881

  Router 2

  68.96.215.121:8882

  How can I do this?

  Strange. 8882 to 80 single port forwarding should work.

  You cannot change the web interface on the side of LAN port. All you can do is disable/enable http and https, which means using the port 80 (http) or port 443 (https). You cannot change the ports.

  Why do you need to access the webinterface of the second still? It is not really a lot, that you can change on this one because it is only an access point and the switch...

• How can I connect two router WRT610N wireless via a modem

  My problem is that

  I want to connect a "wrt610n router" to moden directly cable yet and when I conect the two of them everything works fine and ITI gives good internet connection via WLAN

  Modem ip - 192.168.1.1

  first WRT610N router ip - 192.168.1.10

  But, when I tried to plug "second WRT610N router" by "first a router WRT610N" through second lan_cable(cat 5) router no internet connection provide (give)

  second router ip - 192.168.1.5

  so please tell me how can I solve this problem...

  This article may be able to help:

  http://www6.nohold.NET/Cisco2/UKP.aspx?VW=1&docid=785463d9ecaf4cac84aed245b08d615f_3733.XML&PID=80&r...

• How to change IP cluster and management for the two interconnections Faric

  I need to change the IPs. How can I do this using the console? It was easy enough implemented, but something else when I need to change the addresses...

  This isn't the production

  Post edited by: Atle Dale

  Atle,

  This should help you:

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/CLI/config/Guide/2.0/b_UCSM_CLI_Configuration_Guide_2_0_chapter_0100.html#task_2A93612BB74B49F5947FC916CB2E3571

  . / Afonso

• WRT610n as an access through WET610 Point

  Hello.

  I have the following network configuration. Linksys E4200 is a main router that connects directly to the internet. I also have a couple of bridges WET610. One of them sends Internet through WAP610 (point - works very well to access linksys). Another is still free, so I want to share internet from the second WET610 through my router WRT610n I tried to use the same setting as people recommended for direct cable connection of two routers (WRT610n WAN-> LAN from the main router; DHCP and NAT on the off WRT610 of WRT610 IP differs from the main router IP), but it does not work in my case (WRT610n WAN-> WET610->-> E4200 wireless). Unfortunately WRT610 does not see DHCP (so no client receives correct IP, I can't reach my network if I connect to WRT610, I can't reach the WRT610 of my network).

  Can you help me with this? I thought that the case could be traced, but I failed to deal with them, unfortunately.

  Do not use the WAN port on the WRT610N.

• Cisco UCS Manager does not discover C240 Server

  Hello, Cisco community!

  Currenlty UCS manager shows two interconnections of fabric and two extensions of fabric, but for some reason, my server isn't appear

  Birds seen are:

  I have my C240 connected with two 10GbE twinax cables, each going to a fabric Extender. (Total FEX 2)

  I have two 10GbE twinax cables connected each interconnections FEX fiber modulus in each tissue. (Total of 2 FI)

  The fabric interconnect ports L1 and L2 are connected to their corresponding ports. If their connected to each other.

  I run 'show cluster extended State' on the primary FI and this is what I get:

  FI - A # show cluster extended State

  The ID of the cluster: 0xebaad0e28ded11e3-0x86d4002a6a153d84

  Start time: Thu Feb 5 16:07:44 2014

  Last election period: Thu Feb 5 16:23:26 2014

  A: UPWARD ELEMENTARY SCHOOL

  B: UP, SUBORDINATE

  A: Member State UP, lead, State State PRIMARY, mgmt services: UP

  B: Member State UP, lead SUBORDINATES, mgmt services state: to the TOP

  State of PRIMARY_OK heartbeat

  INTERNAL NETWORK INTERFACES:

  eth1, up to

  eth2, up to

  HA IS NOT READY

  Any device attached to this fabric of interconnection

  After you set up server-side on each FI ports, the server still does not appear

  Any ideas are highly appreciated!

  -Alex

  Hi Miguel

  It seems to me, you're running a rather old version of UCS.

  In my screenshot you see the pool ext - mgt KVM on the LAN tab

  In an older version (I think< 2.1),="" this="" was="" under="" the="" admin="" tab.="" please="" have="" a="">

• redundancy switch

  Hello, I have two layer 2 switches. My requirement is to provide a fully redundant LAN. That means that PC is connected with a switch in case of failure of their connection will have all the time means that they will connect with any other switch to keep communicating through LAN. Please can someone suggest me an architecture that suits to draw CISCO packet.

  Good question, Leo.

  The best way is to have at least two nic card on your PC (with the same speed). with etherchannel, you can bring it to two different switch.

  Note that in Etherchannel, you have LACP and PAGP. LACP is good when you go on two different switches. two interconnect your switches, you can use the cable port or trunk right between the two switches.

• Combine in merger Mode?

  I have a tedious production job, I'd love automation assistance.

  I get page layouts with multiple layers of pictures of products (with transparency) in Normal blending mode. Most of these layers also have separate layers of shade in the blending mode to multiply. (These layers have sometimes masks, othertimes not.) Depending on how the file was built, layers of product could be close to their layers of the shadow, or they can't, making it difficult to organization and contraction.

  (In case it matters, sometimes all the layers (products and shadows) are housed within a single group, there is sometimes some groups in all)

  Finally, I would like to merge all the layers in the layer product a way Normal, and all the shadow of nappies in a single multiply layer mode (with masks applied), with two interconnected layers.

  Layers can be identified and merged according to blend modes?

  This might work.

  But, this does not take into account possible masks on groups and only multiply them artLayers in a group and all others in another.

  // move all artlayers set to multiply and all other artlayers into two layersets and then merge those;
  // 2011; use it at your own risk;
  #target photoshop;
  if (app.documents.length > 0) {
  var myDocument = app.activeDocument;
  var artLayers = collectLayers(myDocument);
  var multiplyGroup = myDocument.layerSets.add();
  multiplyGroup.name = "multiply";
  multiplyGroup.blendMode = BlendMode.MULTIPLY;
  var normalGroup = myDocument.layerSets.add();
  normalGroup.name = "normal";
  for (var m = 0; m < artLayers.length; m++) {
       var thisLayer = artLayers[m];
       if (thisLayer.blendMode == BlendMode.MULTIPLY) {
            thisLayer.move(multiplyGroup, ElementPlacement.PLACEATBEGINNING)
            }
       else {
            thisLayer.move(normalGroup, ElementPlacement.PLACEATBEGINNING)
            }
       };
  normalGroup.merge();
  multiplyGroup.merge();
  };
  ////////////////////////////////////
  ////////////////////////////////////
  ////////////////////////////////////
  ////// function collect all layers //////
  function collectLayers (theParent) {
       if (!allLayers) {
            var allLayers = new Array}
       else {};
       for (var m = theParent.layers.length - 1; m >= 0;m--) {
            var theLayer = theParent.layers[m];
  // apply the function to layersets;
            if (theLayer.typename == "ArtLayer") {
  // exclude background layer;
                 if (theLayer.isBackgroundLayer == false) {
                      allLayers.push(theLayer)
                      }
                 }
            else {
                 allLayers = allLayers.concat(collectLayers(theLayer))
  // this line includes the layer groups;
  //               allLayers.push(theLayer);
                 }
            };
       return allLayers
       };
  

• two or more frame with fabric in cluster interconnect

  Hi experts

  I just want to confirm the proper way to connect two or more UCS 5108 chassis with a pair of interconnect fabric 6120xp clustered.

  I though that they should connect like this: the tissue Extender first of all chassis must connect on interconnection fabric A and second all chassis tissue Expander connects to the fabric interconnect b. as on the diagram here: https://supportforums.cisco.com/docs/DOC-5949

  However, I saw someone did: 1 chassis connects as I went through although above but for the 2 chassis, fabric Extender 1 connect to the B interconnection fabric and fabric fabric Extender 2 interconnect a. -

  can someone tell me which is appropriate/best practices? no reason the second chassis enjambment?

  Thank you

  Ming

  Ming, you must fix this implementation.  It's like ghostbusters: do not exceed the streams!

  Always systematically cable chassis fex to interconnection fabric.  Most common installation:

  Interconnection of fabric (primary) is connected to the hand (looking for the rear of the chassis) left FEX

  Fabric interconnect (subordinate) B is hand-bound straight FEX.

  Why?  You will get errors (can't be bothered them up!) and if you move a Service profile to a chassis to another chassis that is wired differently, it will not work (CNAs wired to different financial institutions, where the living are active / inactive = bad).

  PS - to change this, if I were you, I would like to turn off the entire system - fabric interconnects, chassis, everything.  then re-cable.  then turn on the fabric of the interconnections and chassis and check configurations are ok.

• Interconnect two SG500 base MGBBX1 or GLC-BX-D?

  Hello

  I want to connect two switches SG500 over a distance of 150 meters. I really need a MGBBX1 on one end and a GLC-BX-D on the other end?

  Sounds wiered for me... Why is this?

  Kind regards

  Klaas.

  http://www.Cisco.com/en/us/docs/interfaces_modules/csbna/MGB/Quick_Start/guide/Optical_Module_QSG_en-us.PDF

  Hello

  ----

  For the Cisco MGBBX1, use the Cisco GLC-BX-D as the

  SFP downstream. For the MFEBX1 of Cisco use Cisco GLC - FE-

  100BX-D as SFP downstream. The Cisco MGBBX1 and the

  Cisco MFEBBX1 only supported upstream

  -------

  Since you are using a single strand of fiber, you have a different wavelength to send in each direction.

  One side transmits using the 1490 nm wavelength, and the other side is transmitting on the wavelength of 1310 nm (and the reception on the 1490nm).

  The MGBBX1 only supports the upstream - U version AFAIK. Side acccess to the central part of the network.

  In the kernel, you need the other version, so there is no MGBBX1 SKU for this version.

  If possible, on 150 m, you should consider Multimode with 2 wires and MGBSX1

  1000Base-BX10 is capable of up to 10 km on a single strand of fiber.

  hope that helps

  JO

• Why the interconnections of fabric can be connected to the two MDS?

  Hi all

  1. why the white paper below says that if FI is connected to two MDS, then it will create a single point of failure?

  http://www.Cisco.com/c/en/us/products/collateral/storage-networking/MDS-9500-series-multilayer-directors/white_paper_c11_586100.html

  This image below is used to describe the scenario for question 2 to 4.

  San.PNG

  

  2 and why the SAN design best practices to create SAN A and SAN B? Where when the switch 1 has failed, then it will use the b in SAN. And in this case, user can configure to connect to the storage using SAN B first, instead of using SAN first? And by default, the behavior of the SAN like that, what I mean is that she will check SAN failed, then it will use SAN B?

  3. and why there is no connection between the left more server and switch 2? They can not who design when switch 1 has failed, then it will use the other link first to switch 2, by linking the left more server for 2? Then when the core SAN switch one down, he uses the SAN B connection.

  4. can you the server to different SAN multipath? In this case, SAN A and B.

  Thank you

  Osbin

  Hi Osbin,

  Why the white paper below says that if FI is connected to two MDS, then it will create a single point of failure?

  Protocol FC build tissue, using the FSPF (such as OSPF) of the Protocol in order to MDS, FI (switch mode) Nexus 5 k, 7 k (storage VDC) form a single fabric using the links intercommutation.

  If a problem is occur in tissue alone device's problem (zoning, FSPF, EENT)

  If you connect fabric and fabric B (connect a FI for switch 1 and switch 2) in other words, this is no fabric A and B - it became a unique fabric (fabric single = single point of failure). That's why we use two FI, connected to two independent fabrics (isolation and redundancy)

  Technically, you can avoid this problem by using VSANS, but if some problem in a NX - OS or SAN - OS occure you may lose the two fabrics in a single failure (the worst of the world SAN)

  2 and why the SAN design best practices to create SAN A and SAN B? Where when the switch 1 has failed, then it will use the b in SAN. And in this case, user can configure to connect to the storage using SAN B first, instead of using SAN first? And by default, the behavior of the SAN like that, what I mean is that she will check SAN failed, then it will use SAN B?

  Point main initiator is in the answer above, can use both at the same time (multipath) fabrics with special drivers.

  It is configurable by the user to use any fabric (A and B - is just for engineers) first.

  It depends on the OS and drivers.

  3. and why there is no connection between the left more server and switch 2?

  I believe that this picture is schematic diagram and imagine if you have enough ports in the switch 1

  They can not who design when switch 1 has failed, then it will use the other link first to switch 2, by linking the left more server for 2?

  Remember the idea of FC fabric. If you spend 1 it will affect every single switch fabric, and it is much faster to use stable fabric B instead of A fabric converging.

  Then when the core SAN switch one down, he uses the SAN B connection.

  4. can you the server to different SAN multipath? In this case, SAN A and B.

  Yes

  Best regards

  Alex

• Connect an apple iPad two televisions

  We have two Apple TV in the Office we need to connect to an IPad. We managed to connect one of the TVs now showing a PowerPoint presentation. My question is that we can connect two TVs to the IPad even? If this is possible please could you let me know how we can do this? TIA

  Hello. It is certainly not part of the normal application of AirPlay. If the two screens are not too far away, you might consider a multi HDMI splitter like Monoprice. Some of them use Cat 5 cable as interconnection, so you do not really long HDMI leads.

• What is the right way to extend a network with two stations 80211ac wireless fixed extreme apple via ethernet?

  I my house wired with ethernet and have logged as many devices via cat5e as possible. My problem is when I try to connect together the two apple airport extreme base stations and use the second to extend my network I lose the internet connection.  I am able to extend without problems via radio, but since I plugged in the House tried to take advantage of the fastest method by cable.

  Here's my network setup in a nut shell.

  In the basement, I have my router from Verizon Fios (gateway 80211n) currently configured to provide all the space an Ip address via dhcp (disabled wireless)

  Gigabit ethernet port 8 wired via gigabit switch through the cable between the bridge Fios and port 1 of the switch.

  two iMacs wired directly the fios gateway ports 2 and 3

  Base station extreme elementary apple (call it down at the moment) connected to the Fios bridge

  Extreme basestation secondary apple related to extreme primary apple base station

  Cable to switch TV

  Nintendo Wii connected to the switch U

  Apple TV connected to the switch

  Drive Blu - ray connected to the switch

  My mainly the Airport extreme is configured as follows

  connect via DHCP

  Address of the router is set to the Fios router

  FOR DNS, I used back free servers like Google, and level 3

  Wireless is set to create a wireless network

  Security is set to WPA2 Personal

  Turned on 5 GHz and 2.4 and 5 ghz are set to automatic

  Router mode is set to bridge mode off

  Second or first floor Airport extreme config

  Connect using dhcp

  Address of the router is also the Fios router

  Servers DNS is empty

  Wireless settings

  Network is set to extend a wireless network

  the wireless network name reflects my network

  wpa2 personal wireless security game

  Network

  Router mode is grayed out and pondered or bridge mode

  Second or first floor Airport extreme config...

  .. . Network is set to extend a wireless network

  Given that all routers are interconnected by Ethernet, you don't want to configure AirPort Extreme to "Extend a wireless network." This option should be used only if the connection between the wireless base stations. Instead, the two base stations must be configured to "create a wireless network.  This is because that, with them all connected by Ethernet, you have the basis for a network of mobile type.

  With this type of network, each router will broadcast their own Wi - Fi network, but because they will all use the same network name (SSID) and use the same type of wireless security and the password, all the wireless clients will see them as network «one»

• Two-way-going with USRP n210

  Hi all

  I'm doing a two-way-going using the USRP n210. To be able to do that, I will need to know the exact time that samples have been sent and the time that I have received back.
  Trying to implement that I want to use 2 USRPs linked together.
  (USRP HAS)              (USRP B)
  TX<----------------->
  rx -----------------> tx

  For the porpuses first test, I used a single USRP linking the RX and TX together. With the help of a simple flow in the RRB graph I out a pulse (using the vector source) and at the same time, I have everything from the entrance of the USRP stored in a file (using the file sink block). For comparison, I also used a file sink block in the output.

  Testing again the difference between when I starts the code and the time the impulse arrives at the RX looks like that there is a kind of random delay. The difference between the send and receive in return the pulse fluctuates around 8000 ~ 10000 samples. Because I use a single USRP with RX and TX interconnected I though that this time limit should be almost zero.

  There's a better way to implement what I can get better accuracy in the timestamp?

  One solution that has helped me to solve my problem was using the following code in the code generated by the companion of GNU python:

  now = self.uhd_usrp_sink_0.get_time_now (#Store) the real time of the FPGA
  Self.uhd_usrp_source_0.set_start_time (UHD.time_spec_t (1) + now) #Set the source to start 1 second after the real time of the FPGA
  Self.uhd_usrp_sink_0.set_start_time (UHD.time_spec_t (1) + now) #Set the sink to start 1 second after the real time of the FPGA

  In this way both tx and rx, will begin at the same time.

• How to create a component that has two holes with a unique NET linking both.

  I tried to create a piece which contained 2 holes with a strip of copper between them so they would have to connect to a single network, but one of the holes (axis 2) gets rejected by Ultiboard as a non-connected entitiy. Is there a way to define the second hole (2 pins) so as to mitigate the problem?
  Thanks, Tod

  Hello

  It's pretty simple to do:

  When you print, you put just your two TH pins where you need. Name them 1 and 2.

  Then in Multisim, during a new component with the component wizzard, in step 2 do a component 1 pins, then select your desired print (which has two pins).

  thenin step 3, brand / choose your symbol 1 pins.

  In step 5 you can map the footprint on the symbol, simply use the two pins of the footprint for the same symbol PINS.

  When using it in your schema, you will see a PIN, in the page layout, there will be two main interconnected...

  Good luck

  user stressed...