Two questions about upgrade the sensor software

Similar Questions

• question about cleaning the sensor of the A57

  Dear community of Sony,

  I have several questions about the cleaning of the sensor of the A57.

  Recently, I noticed several dark specs appearing on images when shooting at low opening (F20, F22), especially when there are high for them (like the sky in a landscape photo) contrast. To my knowledge, I've categorized as possible of dust on the sensor. I have read the section of the manual about cleaning the sensor and followed the procedure. However, the problem remained. I have previous experience with cleaning of the more resistant the probe of a Sony NEX dust particles, so I applied it to the A57. I used the specialized sensor cleaning tools combining two parts kit - wet and dry. Noted little dust on translucent mirror as well, so I cleaned up afterwards. Later, I considered this mirror could have some specialized coatings.

  So my first question is: should I have done some permanent damage the mirror or the sensors? Currently, the camera works OK, although some features of dust still remain. It seems that I had pushed some of them to the edges of the sensor.

  I'm not so happy with the tool that I used. I'm thinking about this one for a more thorough cleaning:

  http://www.digitaltoyshop.co.UK/Eyelead_sensor_cleaning_kit_SCK-1_Sony_Alpha_A57_t2836_6789

  It is marketed as a tool for A57. Should I use it?

  Thank you in advance?

  Best regards Angel Marinov

  PS: I'm really happy with my Sony A57 and the NEX. They made me a fan of Sony. So, I want to use this topic to also say thank you to the developers of Sony.

  Hello Angel!

  Read the following steps carefully and let us know if you have any other questions.

• Satellite A50 543: Questions about upgrading the HARD drive

  I'm looking to upgrade the internal hard disk on my A50 543 to 100 GB at 7200 RPM. The original drive is a Fujitsu 60GM 4200. I have found no information on the Internet on other readers line CMS that have been tested and found compatible with the A50. I need at least 5400 RPM or 7200 RPM to edit video.

  Suppliers meet usually only with so many laptops on the market, they cannot test each hard drive with any laptop, but can tell if it is compatible with the specifications of the computer and the hard disk specifications and are so confident that their information is accurate that they offer a money back guarantee (excluding shipping costs)

  My question is
  (1) how can I be sure that the drive will work (considering the high international shipping costs) to 100%?

  (2) none of the contributors to this forum may recommend a hard drive internal 5400 RPM or more it has installed on the same model specification?

  Thank you. You are my last hope

  Best regards
  Vince

  Hello

  If you want to be 100% sure that works on your HARD drive, so I think the best way is to contact the after-sales Service of Toshiba partner. Here, you can order all the devices and parts compatible and supported.
  I also found these Toshiba hard disks that must be compatible:
  HDD2187B 20 GB 4 200
  HDD2190B 40 GB 4 200
  HDD2193 40 GB 5 400
  HDD2189B 60 GB 4 200
  HDD2194 60 GB 5 400
  HDD2188B 80 GB 4 200
  80 GB 5 400 HDD2191

  In this case, you can use a disk HARD of GB 5 400 80 but I put t found no information about 100 GB of HARD drive.

• Equium P300-190 - Question about upgrading the processor

  Hello

  I just have a question for my CPU PC Toshiba laptop, I have a can of Equium P300-190 full to give model number if necessary the cpu is one supplied with the laptop.

  My question is I want to upgrade the processor but do not know which would be the best option and there are limits with the BIOS, etc. on board.

  Any help would be greatly appreciated.

  Probably it is not known to you that upgrading the CPU is not officially supported by the manufacturers of portable.

  The CPU upgrade is a tricky thing... the fact is that the CPU must be supported by chipset and BIOS.
  Where a party would not support the new processor, the unit will not light.

  So even if you use a CPU that is supported by the chipset (Intel GM965) there is a risk that the BIOS could not support the new processor...

  The laptop was equipped with processor Intel Pentium Dual-Core processor T2390 (Merom code name) probably the other CPU Intel Pentium Dual-Core family-owned would be compatible, but to be honest, you won't see a performance improvement...

  So in my opinion it is not worth trying to upgrade the processor...

  In my opinion, you need to replace the HARD drive with an SSD... in that case you will get the performance improvement...

• Satellite A40 - question about upgrading the processor

  If I upgrade my Satellite A40 processor with hyper-threading technology to 3 .00GHz, the problem s s don't past not my chipset for hypo threads, should I have a problem on my terms of portable?...

  Hello

  If you open your notebook and do something about yourself, you will lose your warranty.

  Just FYI; the processors used in laptops are connected to the motherboard using a process called TCP (tape carrier package). It is a method of permanent connection and is used in the interest of miniaturization and heat dissipation. As far as I know because of this method of connection, upgrade the CPU is not possible.

  Good luck!

• Question about upgrading the CPU for Satellite 1110-Z14

  Hello

  My satellite 1110-z14 has a processor intel mobile celeron @ 1.5 ghz. The processor is based on architecture p4 - it should be a northwood-256.
  Is it possible to upgrade the processor?

  1110-z20 is powered by the mobile celeron @ 2.0 ghz - all other technical specifications except the hard drive are the same... (ati radeon m6 with 16 MB, usb 1.1 mob and so on...).

  What do you think, can I upgrade the processor?
  Can what cpu I use?

  Thanks for your replies!

  Hello

  AFAIK the 1110 series computer is equipped with an Intel 845MZ system controller.
  I found some details about Intel 845MZ chipset on the Intel page. It must be able to manage the Mobile Intel Pentium 4 - M with 400 MHz FSB Processor
  http://www.Intel.com/products/chipsets/845MP/index.htm
  On the Intel page, you can find the entire family of the CPU.

  But generally the replacement of CPU and the upgrade is not recommended and no one can say whether the OS will run stable after these updates, so be careful.

• Satellite A200SE - Questions about upgrading the HARD drive

  I am trying to upgrade the disk of 60 GB to 250 GB. The operating system is Windows Vista Business. The new drive is a Western Digital Scorpio SATA.

  1 - image backup of the disk system external HARD using backup/restore Vista
  2. use the system recovery disk to reload Windows.
  3 - the disk is formatted and Windows installs apparently. (From recovery disk.)
  4. after reboot, Setup is aborted with message saying (roughly) "Setup cannot continue because of the configuration".
  5 - as usual the message gives no indication as to the cause.

  All the tips and forums involve replacing drive HARD is simple. Does anyone have an idea?

  Ideas would be very appreciated!

  Hi scamp126,

  I m wondering recovery disc doesn t work because usually this disk still works, you install a new HARD drive

  What you can try is a Microsoft Windows disk. Perhaps that the recovery disk is scratched and the files can't be read properly.

  Check this box!

• Satellite P100-429: Question about upgrading the processor

  When I bought this model 6 months ago I got this one with just a T5500 1.66 GHz but since then Intel reduced prices 40% it is me the upgrade option.

  Someone at - any idea how I can update, the following list lists the T7600 @ 2.33 GHz compatible on the Bus speed and execution step by step. The only difference being the memory cache L2, 4MB compared to my old one of the 2 MB that will have an effect.

  http://i82.Photobucket.com/albums/J249/swoggy/cpuspec.jpg

  Thanks for anyones help.

  Hello

  Upgrading the CPU is a bit tricky on laptops and more often than not desirable and is not possible.
  After the CPU overheating upgrade, it would be possible that don t cooling modules are working properly and the laptop.
  Why? Well well, the CPU new and stronger products, more heat and the temperature would be Monte. The fan table that is stored in the BIOS will not correspond with the new CPU and the cooling fans would not correctly work.
  In addition, upgrading CPU will void your warranty! It's very risky!

  Anyway, looks like you certainly want to upgrade the processor?
  So I would check the chipset installed on your laptop.
  Try to know the details of the chipset and Intel page for compatible processors research!

  concerning

• Questions about upgrading the video card in the Inspiron 620

  Hey guys... I want to add a discrete graphics card to my new Dell Inspiron 620.  My power supply is rated at 300w.  Are there maps decent graphics that I could use that would be compatible with the 300w PSU?  Also, if I upgrade my diet as well, which could result in the cancellation of the guarantee I have on my new Dell?  Thanks in advance!

  Much here on the forums have used the HD 5670 on their units of 300 watt with no problems.

  By the table below, you can see that the HD 5670 is only set to 190 watts in charge for the entire system.   I think that the video card will do only about 50-60 watts in game situations and where the only game not only around 20 watts.

  

• Satellite 2800-600: Question about upgrade the BIOS?

  I have Windows ME and XP Pro installed on my satellite 2800-600. On Toshibas downloads page have both their own updated BIOS. Which to choose, because the upgrade of BIOS are usable that with Windows ME and XP upgrade only with Windows XP?

  Hello

  I would use the BIOS XP because most producers BIOS meet OS at the level of the back. The BIOS for ME maybe not compatible with XP.

  concerning

• Questions about upgrading the graphics card.

  Hello.

  I just increased my RAM up to 5 GB. It was before 3GB.

  I have a Windows 7 OS 64-bit. I want to install a graphics card. Should what capacity I buy?

  Thank you.

  PS: To clarify, I want to use my PC for gaming. So should I buy a 1 GB card or more than that?

  Since you don't specify what type of programs you use, no one can say.

  If you use standard Office type programs it will matter a lot, if you use graphics software or games it's something different, and that the software would have minimum requirements on this site.

  Of course if it is a laptop you are unable to pass the graphics

• Question about upgrading the LR5

  When I try to download updated LR5 can updated the Adobe site tells me that I need to improve my internet explore when I actually run IE10 how I solve this problem.

  Alternatively, please turn the compatibility mode in Internet Explorer 10.  You will find more details on the site Fix display problems with compatibility view - http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-10.

• two questions about Style sheets

  With the help of RH7, two questions about styles:
  
  1. I have an older project which seems to act weird. I want to update the styles in our current one important, but seems not to accept it. I can import the file very well, but it doesn't 'take' the formatting (e.g. headers, 'Normal' text, etc.).
  
  It is important without any errors, and in the list of the topic the new style sheet shows like the style associated with this topic, but I can't find a way to apply new formats. I even tried closing and reopening of HR to see if it was some sort of refresh problem.
  
  Any thoughts? Is this a problem of corruption?
  
  2. it seems some of previous authors allowed HR to create of new style sheets for each topic as it has been imported into our system of assistance (from the original Word documents).
  
  Is there an easy way to globally remove these style sheets and their replacement by a new? My instinct is to:
  
  1 import the new style.
  2. Select all subjects in the list of topics, right-click to open the properties, and select apply the new style.
  3. use Project Manager tab to remove all the other styles.
  
  Sounds easy enough, but my concern is to know if HR will apply these changes to the subjects. In addition to my problem in #1 that I met occasionally issues where HR does not seem to apply styles or style changes accurately.
  
  Thank you

  Hi all

  Note that Styles and Style sheets have an order of priority or hierarchy.

  You can have all the styles declared in a referenced external style sheet and everything is fine. But if the document has styles using the same names, those who will prevail.

  For example, maybe your file CSS says that all title 1 text will make in dark blue to 24 point Arial font. The subject could have statement Heading 1 incorporated, which specifies that the text should be Brown in Verdana 12 point. Even if the subject is properly referencing the external CSS file, the text will be rendered Brown because the embedded style rule will override the CSS rule.

  And what will replace it is if someone text selected and applied the style directly. In this case, you're dealing with a style online.

  One way to help determine if you are dealing with a style incorporated is to simply remove any link to the CSS file? The text seems always the same? If so, you probably deal with a built-in style, or online.

  To check a style incorporated, look at your HTML code for the topic. Search in the region of the head for a (including the tags).

  See you soon... Rick

• Satellite A20-S103D: two questions about the recovery process

  Hello

  I bought the machine above my nephew - is no longer necessary.
  It runs Windows XP Home Edition and is not a Windows CD or disc of recovery of any kind.

  I have a Windows decal on the underside with the product key, but when I use "Belarc Advisor" to examine the product keys for all my software loaded it gives a totally different operating system product key! This key contains the letters OEM in there.

  As the machine is supplied with a Toshiba power management software I guess it's an OEM Toshiba of the OS version I have.

  My questions are:
  1 / this does not mean that at some point in the past, this machine was another product of Windows XP on it? (two product keys)
  2 / I can, (and), I get the Windows XP CD or a recovery for the machine, like I need to recover or to reload Windows.

  Thanks in advance to all members of the forum that meet.

  > 1 / this does not mean that at some point in the past, this machine was another product of Windows XP on it? (two product keys)

  The key you found at the bottom of the device belongs to the OEM of Windows version that is part of the recovery diskette.
  The recovery disk is already enabled so that the key is not required in order to activate the Windows operating system.
  As far as I know, that the key does not work with other versions of windows

  > 2 / I can, (and), I get the Windows XP CD or a recovery for the machine, like I need to recover or to reload Windows.
  Since it is an old, I doubt you'd be able to order the recovery for this device disc
  If you want to install the Win operating system, then you must use a Windows CD clean valid keys and all drivers may be downloaded from the page of European driver of Toshiba.
  The drivers are placed in the archive because it oldie s in order to choose the archives in the type of product to download the form.

• two questions about the scattered images secure

  I created an image that is secure and encrypted for sensitive documents.

  I have two questions:

  1. when I use the disk (if it is up, open and available), and I want to add something to it, I usually drag the file everywhere where it is currently in its destination folder in the sparse image control.  But it automatically makes a copy - with the same name (not with a '-1' ever, not with a suffix 'copying' or 'alias').  Which defeats the purpose and makes things complicated - I find myself comparing what is in each location to make sure it's in the sparse image and then it makes me nervous to delete the original.  Why it does this and how can I change such as dragging a file in a secure location gives there is not that a second copy of it left in an UNsecure location?

  2. I'm using Time Machine backup drive sitting on my desk (and a separate utility for monthly clones on a different backup disk).  Automatically makes Time Machine backup the content of the rare picture even if the safe drive is not mounted, open and available?  I hope not, because that would undermine the usefulness of having a backup disk on my desktop running of ordinary Time Machine backups, but find it me just that all the steps I take of course I do not lose any data may be so overprotective I have thought/hoped.

  Sous_forme_d' addendum, I'll check my clone, but as I put this out there, I wonder if SuperDuper!, my application of cloning is cloning automatically secure disk content, so... like the thoughts of anyone about it if it's an application that they use).

  FYI: I'm running 10.11.2

  Thank you.

  (1) by default, OS X makes a copy with the overcoming of the limits of volume and moves when in the same volume.

  You can reverse this behavior by holding down the command key when you drop. You will see the insignia of the icon changes (green + for copy, empty for move).

  (2) Time Machine will return to the top of the image 'file', but only when it is unmounted. I do not think that it automatically includes the volume mounted, but I would like to check and add to the exclusion list.