"Type of incorrect PDEObject.

Similar Questions

• OfficeJet Pro 8500 has more: format of paper PAPER MISMATCH or type is incorrect message

  When I try to print a regular 8 1/2 x 11 paper, I get an error message that says "paper mismatch: paper size or type is incorrect." What happened recently power, and sometimes I couldn't the printer to print if I power off (reset) completely and/or rebooted my laptop, or if I deleted the printer in the preferences system and then he readded.  But now, not even these solutions are effective and I get the error message.  I followed the following steps: http://support.hp.com/us-en/document/c01824353 and had no luck.

  If I could just replace the message, it would be a cure, because everything that I never print is 8 1/2 x 11.

  I am not sure, but it may have started to happen after I upgraded my laptop 10.9.5.

  Anyway, if I could dare ask you to respond very clearly and in a sort of step by step of passage. I'm a Baby Boomer, so it is not intuitive for me, thank you in advance to give me very simple instructions!

  Hello

  Please try the procedure on the fron printer below Panel.

  1. Press SETUP, then
  2. Touch TOOLS, then
  3. Touch RESTORE to the FACTORY DEFAULT

  Now try printing.

• C5180 tells me that paper is the right size or type is incorrect.

  I have a photosmart c5180 all in one. I started having an error message, the incompatibility of paper. size of paper or type is incorrect. I used the same paper in the same place for years. I did everything I know how to fix.

  Any suggestions?

  Normally, it is thanks to sensors of paper in the paper from the printer tray. If the paper sensors are dirty, damaged or blocked, then the printer will display a paper or paper Mismatch message.

  There is a document in paper Mismatch questions located here.

  Let me know how it goes.

• type is incorrect and is worsererer

  Take a look at your iTunes library and particularly to the column TYPE for music 9i just have music on in my itunes)

  Crawling in East entered incorrect "gender." That is to say a torn mp3 is seen/listed as a purchased AAC file.

  You see it too?

  I do not Match, use iCloud.

  12.3.2 iTunes

  10.10.5 OSX

  Take a look at your iTunes library and especially in the TYPE column for the music (I don't have music on my iTunes)

  Crawling are casual (dozens, if not more) entries incorrect "gender." That is to say a torn mp3 is seen/listed as a purchased AAC file.

  You see it too?

  I do not Match, use iCloud.

  12.3.2 iTunes

  10.10.5 OSX

  He is no longer a preview button so I reposted, correct the faults of strike. If there is a preview button, it is proposed that, if she did not move I have not see it.

• Type of incorrect spectrum in SMT Spectrum Peak Search

  I get an error message: incorrect spectrum type when I try to use this joint vi entitled SMT Spectrum Peak Search

  Can someone please help?

  you need to convert your data into this terminal of this vi type could support

  the pictures below show this type

  is your data of the spectrum of this type?

• HP PHOTOSMART 3210XI ALL IN ONE: printer says paper size or type is incorrect when you print an envelope from Word

  Hello

  I've had this printer for years & were able to print my envelopes in Word without problem. Today, I tried to print an envelope without result. The printer keeps giving me (type and paper size is incorrect). I have not won the printer & reinstalled. Still no change. Any ideas?

  Thank you

  Dear AIRASSAULT18B,

  Please follo the steps in this document:

  http://support.HP.com/us-en/product/HP-Photosmart-3200-all-in-one-printer-series/439599/model/439603/document/c01824353/

  I hope you find it useful.

  Greetings.

  * I am not an employee of HP, my work is voluntary.

  If this answer was helpful and clarify or solve your problem, please mark the topic as resolved and click on my next star to indicate a kudo, thank you.

• Type of incorrect monitor selected by Vista on new wide screen

  Not sure if it's category material or configuration.   I changed a conventional monitor widescreen Acer F22.  I can't set the correct resolution.  Device Manager indicates that a generic PNP and Nvidia Control Panel it's a Dell 1702.  Acer does not available Vista driver then, how can I change the type of monitor for a wide screen with the correct resolution capabilities?

  Thank you

  Hi clydex2,

  • You try to adjust the resolution via the Nvidia Control Panel or through the Vista display settings?
  • What type of monitor displayed in display settings?
  • What is the highest resolution that you are able to select this screen?

  If you had loaded a driver Acer and were able to set the resolution, then you can try to back the driver after that update.

  1. Right-click on the device and go to Properties
  2. Select the driver tab
  3. Select restore driver

  Let us know if the roller helps return. Matt
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Indicating the type of incorrect disc?

  I did the following and I wondered why he always thin saus:

  1 created a thin disk by gui

  2. I ran vmkfstools-i file.vmdk d zeroedthick file1.vmdk

  3 deleted vm file.vmdk

  4. Add file1.vmdk to vm (by adding the vmdk it says that it is thick)

  5. now change the settings the new drive said thin disc even though I know that its thickness.

  Is - this default, or a bug?

  Thank you

  William

  I did the exact process you mentioned in your message and has not experienced the problem you reported.  When I joined the new VMDK he reported as thickness when adding.  I clicked OK in the dialog box "Edit settings" who committed the VMDK Add.  I checked into "change settings" and it is always reported as thick.  I then proceeded to start the virtual machine to test and check the setting of the new - still thick.  I am running fully patched ESX and vCenter.

  VCP 3, 4

  www.vstable.com

• HP 6500 has more on vista home 32-bit version do not print paper/type of error message is incorrect

  I can't understand how to solve this problem.  It's my default printer.  I get the error message paper/message type is incorrect.

  Tray 1 is correct

  Letter size is correct

  paper normal-media

  normal quality.

  I reloaded the driver, he always sends error message and do not print.

  Solved by the alignment process.

• How do you get the type of incoming IMAP to POP3 server?

  Recently, after getting a laptop with Windows 7, my Thunderbird account stopped to let me see or send emails. I contacted my small ISP and talked with them. One change was that the address I had for their server was no longer used and now the server type is incorrect on behalf of TB: it was IMAP, but should be POP3. I have to go to a reading of general E-mail site to find my incoming emails. I can't find a way to change the IMAP POP3 Protocol, so need your help.

  Configure the account again. When it gets to a point where it shows you the IMAP settings, it can show you boxes to choose between POP and IMAP. If so, select pop. If this is not the case, select manual Config and enter the settings provided by your email provider.

  What reason is provider makes for POPS are correct and incorrect IMAP? If you have run the auto-set-up and Thunderbird discovered an IMAP server, then they of course offer IMAP service, so it is difficult to see why its use is 'bad '.

  Provider who is?

• Cannot add my Lenovo T430s to my products - wrong type, even if it is correct

  Trying to add my Lenovo T430s to my products to get help, but system indicates that the TYPE is incorrect, even if it's just:

  Screenshot of system error:

  [Link to image display S/N deleted]

  Photo specification etiquette:

  [Link to image display S/N deleted]

  What should do?

  Comment to Moderator: Order number deleted to protect members of wrongdoing.

  Finally the added by removing the hyphen.

• These can be wired together as their data types (digital, string, array, cluster, etc.) do not match.

  Hi, I get an error update LabVIEW 8.2 for 2011:

  These can be wired together as their data types (digital, string, array, cluster, etc.) do not match. View the contextual help window to find out what type of data is required.
  The type of the source is cluster of 2 elements.
  The type of the sink is typedef "IMAQ Image.ctl"
  IMAQImage (IMAQImage,).

  This type of incorrect argument can be caused by an old instance of the Image data type.
  To fix, simply replace the instance with the definition of type IMAQ Image.ctl in the control menu of the image palette.

  The source is:

  Call library function node - image (dup)

  The sink is:

  IMAQ_array for image - image

  I tried to delete the image VI IMAQ_array & always replacing but it connects...

  Here is a picture of the VI, I have a number of VI to update and they all have this problem

  Home is also the VI.

  See if you can shed some light on this

  

  The solution, he had to do with the representation of images in the old and the version of Labview

  I'm completely new to NI Vision, so I had no idea what I was looking for

  from this thread:

  http://forums.NI.com/NI/board/message?board.ID=200&message.ID=5849#M5849

• Question about real store type value in the database on Z10

  Hi all

  I'm trying to store a value in the database (datatype is defined as REAL), but the result on Simulator and Z10 is totally different, the two of them, the SDK version is the same (10.0.10.672)

  on the simulation, the value in the database is correct, like this

  

  Z10, the valve can become bad like this.

  

  Define a type of incorrect data or someone has an idea?

  Thank you.

  I think I have sloved... the problem before you record a double or real value in the database, convert QString

  fenceValue["latitude1"] = QString::number(m_FenceFromJson->m_PointFs.at(0).x(), 'f', 6);
  

• ODM deals Mining Type according to the algorithm

  Running of the ODM 3.0.04 version.
  In the node template, the user can select an algorithm and then select the "Advanced" button to display the "Advanced Configuration" dialog box. The Advanced Settings dialog box allows the user to change the 'Mining Type' (for example numeric or categorical) of an attribute. It is, of course, something you have to do much since ODM often guess the Type mines incorrectly. However, dialog boxes require the user to repeatedly change the Type of Mining for each active algorithm - that is, all four algorithms for a Classification model node. I do not believe that the Type mines is a function of the algorithm. For example, if an attribute is yes/no in a classification algorithm, it is always a yes/no attribute for the following classification algorithm.
  
  I suggest doing the part of mining Type selection node of data rather than the node class Build Source.
  
  Is there somewhere other than this forum where we need to incorporate these kinds of suggestions and wishes?

  Hello
  This feature is already scheduled, but it is not well documented or obvious.
  Here are the steps:
  1. the nodes of generation model using a set of heuristics to determine whether to exclude columns from the model of construction process or possibly to change the type of mining (digital to categorical only).
  2. run the node model to build everything first to see what Data Miner provides for the usage parameter data.
  3. to display the parameters of use of data resulting, you go to the advanced settings of the main Editor dialog box dialog box.
  For each model, please uncheck the 'Auto' in the main grid at the top of the dialog box.
  You should now see the details of the setting for use of the data for each model.
  There may be variability as to whether the column is included or not for an algorithm given restrictions of data algorithm type.
  The type of mining will not vary according to the models.
  4. to change a specific setting for more than one model, select all models in the main grid you want change or do ctl - a if you want to select all models.
  Then go to the detail grid and change the settings.
  In this way, you can change the type of mine once, for all models.
  You can also include/exclude columns or turn off the automatic preparation of the data in the same way.
  I will not disable the automatic data preparation, as this could occur in the model build failure if you haven't posted for the preparation of the data required on your own.

  Of course, if you can ignore steps 1 and 2 If you don't want Data Miner to a first cut in these settings.
  For the moment, I made a request to improve the online help for the settings for using data to better explain this behavior.

  Thank you, Mark

• Variable declaration of liaison for the collection type.

  Hello
  
  I have a procedue with collection (type) as output parameter.
  How can I run the procedure of the SQL prompt.
  
  Can I declare a variable binding in the form of a parameter that stores the type of collection.
  
  Thanks and greetings
  Rambeau

  Monica wrote:
  Yes, it's a typo. I also tried with "STOP_STAT_RES", but the result is the same.

  What are you talking about? Without doubt, one of the two generates a compile exception because the data type is incorrect...

  Monica wrote:
  STOP_STAT_RES is a collection of number abd the data types Date.

  Do you mean that you have created a user-defined type (e.g. CREATE TYPE >) which has attributes NUMBER and DATE? And that STOP_STAT_RES is a collection of such user-defined? Can you post the this user-defined type declaration?

  Justin