UCS C200 M2 R200 - 1120402W Nic will negotiate only 100 MB full

Similar Questions

• UCS C200 and NIC Teaming/FailOver

  As UCS C200 with management of a 10/100 and 10/100/two interface 1000 interfaces and PCIe with 4NIC

  I want to install CUCM 8.5 is the NIC Teaming/failover supported by UCS C200 and how to set up the NIC Managment interface with failover?

  Thank you.

  Hello

  As you install apps from the CPU on the server of the UCS, speech application team listed their recommendations here.

  http://docwiki.Cisco.com/wiki/QoS_Design_Considerations_for_Virtual_UC_with_UCS#Guidelines_for_Physical_LAN_Links.2C_Trunking_and_Traffic_Sizing

  You can create a NIC teaming in the ESXi via vSphere client software for traffic from from / destined for virtual machines.

  For C200, we have only one management port and if you use the management for MMIC traffic port, switch option is not available.

  However, if you choose to use host for MMIC traffic NETWORK ports, you can set up CIMC NIC mode for 'LOM shared' which provides the NIC teaming options.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/SW/GUI/config/Guide/1.4.1/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_141_chapter_01000.html#concept_AC4EC4E9FA3F4536A26BAD49734F23D0

  HTH

  Padma

• UCS C200 RAID solution

  Hello

  I hope for your help about the technical question about the RAID.

  We bought a server in a rack of Cisco UCS C200. Now I looking for information on the best RAID solution in our case.

  The question:

  As I understand it, there is an integrated RAID solution: Intel ICH10R in UCS C200 server. We use this RAID configuration now and it works OK. However, we wonder if it is worth installing the PCIe controller (we have HP Smart Array P410 (ATA/dis2) card). We use currently 4 SATA and RAID drives works as expected, but we are interested in, if there are all the advantages of the separate RAID controller card. Above all, we are interested of performance benefits as we plan to have a lot of disk writes (records call - about 10-20 calls per hour, lasting 2 minutes on average). We would be happy to stay with RAID integrated if it works stable. On the other hand, we will install the above mentioned Intel RAID card if you say that it would be the best solution about the reliability and wear of the disc.

  I would be grateful for any comments.

  Kind regards

  Vytas

  Vytas,

  Your question is probably down to RAID levels supported for each card.  The performance of each should be relavitley the same, so I would not concentrate on that.

  The only supported RAID controllers are listed here and must be purchased from Cisco:

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/HW/C200M1/install/RAID.html#wp1015625

  "Others' work, but you'd be yourself if you encountered problems with TAC.

  The integrated Intel ICH10R card supports up to four SATA using RAID0 (striped) or RAID1 (mirror) drives.

  If you need one RAID5, 10 or more, then you must a MegaRAID controller to do.

  All RAID controllers provided by Cisco are heavily on trial and could be your best option for reliability and performance.

  Kind regards

  Robert

• CISCO UCS C200 M2 amber display clear on mem and warning

  Hello

  My company bought 5 units of CISCO UCS C200 M2. The servers are equipped with 2 x 6 core 2.67 GHz. The server was also equipped with 32 GB of ram. One of the shows Server alert light yellow on mem and warning on the front panel. Can someone tell what could possibly cause this problem?

  Thank you

  Logan

  Hi Steve,.

  There could be a faulty MEMORY Strip on the system, in the MMIC, you can check the logs SALT (System event log) that will provide you with more details.

  I give advice you open a TAC case for this, we can take a look at the tech show and understand why accurate and if necessary replace the defective DIMM module / part (if defective).

  Thank you!

  . / Afonso

• Replacing hard drive RAID 10 (UCS-C200-M2)

  Guys,

  I'm running RAID10 on UCS C200 M2 and exchanged one of the defective drive.

  Currently, there is beep for more than 12 hours and I guess that the new drive is under reconstruction at the moment.

  In addition, physical drive status is currently on "not well configured" on CIMC. The status changes to "online" after

  the reconstruction end? Will be required reboot when the rebuild is complete?

  Please advice.

  Hello

  If the State of the reader to not configured well. You will need access to the Webbios to change online status and allow reconstruction to be undertaken.

  You will find here all the information required to set the drive to the State once again

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/c/SW/RAID/con...

  If by chance you encounter any problem do such thing. Call the TAC and they will help out you with it.

  Please note ALL useful answers

• UCS C200 Server Power Supply Question

  We make some changes in our data center and which involves electric grid.  We had to replace our Dustribution of power rack and to respond to the charge, we moved 208V, 3 phase power distribution.  Read the literature, I see that the power supply to the UCS C200 servers can operate 115V to 230V AC.

  My questions are: is it everything I have on power supply from 120V AC 208 v power supply power supply power supply?  Can I have a power running at 120 v and the other operating at 208V?  I try to avoid the closure of the server.

  According to specifications

  http://www.Cisco.com/c/dam/en/us/products/collateral/servers-unified-com...

  Table 41 UCS C220 M3 SFF 450w Power Supply Specificationspescription
  Input AC voltage
  90 to 264 VAC auto-ranging,
  100 to 120 VAC nominal
  200 to 240 VAC nominal

• UCS C200 M2 could not start

  Hi all

  My Cisco UCS C200 could not start. Once checked, I found that the problem is the raid controller, the card may not work properly.

  the type of raid used controller is LSI MegaRAID 9260-4i

  can I replace this controller card with different types such as LSI MegaRAID 9260-8i

  If can, what should I do? are there concerns?

  Thank you for your kindness

  That should be fine.  See the documentation of the TA on the exact process of swapping the controller, but since they are of the same generation, just different port internal account (4 vs 8) and all RAID information is stored on the discs themselves, you should have no problem exchange controllers and imports of table on the new controller.  Once swap you controllers, host of startup, enter the optional ROM of LSI and check if the table is waiting for import (if she is not the automatic import).

  Kind regards

  Robert

• MMIC UCS C200 M2 blade - cannot access

  Hi all

  I was hoping someone in this forum could help with a problem I have on a customer site. We have therefore two blades UCS C200 M2 we cannot access MMIC of. When I try to reach the IP address, the browser just sits there, but the IP address is an echo request ICMP who responded. I rebooted a systems press F2 and tried to launch the utility BIOS Setup MMIC but received a message "no attention not found" and the only option was to hit very well.

  What would cause this? And should I update the firmware? If I need to update the firmware how can I go about this...?

  In addition, these systems are running ESXi 4.1, but I believe that the version of VMware is not compatible. Could someone help me confirm this?

  Any help is greatly appreciated!

  -Bobby

  Hello

  It worked before?

  If this is not the case, try resetting the MMIC or it could be a browser/java problem too. The problem exists across the browser and several pc user.

  See doc below to configure the Mmic

  http://www.Cisco.com/c/en/us/support/docs/servers-unified-computing/UCS-...

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/c/SW/CLI/CONF...

  -
  Siva

• What ESXI host NIC will use when the membership of the AD?

  What ESXI host NIC will use when the membership of the AD?

  I have a domain on ESXI host controller and I want ESXI to join the AD? I need to create a vmkernel for the goal?

  Hi Welcome to the communities,

  It will use the management network, which uses vmk0 as a default, no need to create a new vmkernel.

  Then look up what vmnic is connected to vmk0 in your installation.

  Concerning

  Tim

• HP EliteDesk 800 NIC question - 100 MB/FULL works not

  
  

  We have found a solution to our problem with the i217-lm

  Regardless of if we put the NIC at 100 MB/full, it has always tried to auto neg and neg to 100 Mbps half, despite all 100 MB/full switch and no auto Neg.

  To correct, look in the registry for the LinkNegotiationProcess key and set it to 2.

  In our case, there are 3 instances that need to change.

  The default setting is 1, which is to auto negotiate. 2 is forced. This solves the problem on all our 800 EliteDesk from HP.

  Reg keys if anyone is interested for our Intel i217-LM NIC:

  Windows Registry Editor Version 5.00

  [HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0007]

  'LinkNegotiationProcess' = '2 '.

  [HKEY_LOCAL_MACHINE\SYSTEM\ControlSet002\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0007]

  'LinkNegotiationProcess' = '2 '.

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0007]

  'LinkNegotiationProcess' = '2 '.

• Lets say I got a $10 gift card balance and I want to buy something will be only charged debit card 10 cause of $20 s $ of the balance of the gift card?

  Lets say I got a $10 gift card balance and I want to buy something will be only charged debit card 10 cause of $20 s $ of the balance of the gift card?

  Unless it's a gift card or otherwise indicated, the debit card will be charged $10 plus tax on this item.

  (143858)

• WhatsApp will not only restore to backup photos

  Hi, I had to wipe my phone and I restored it to iCloud (ultimately what is the point of paying for it otherwise).

  My whatsapp backup was 5 GB, including the media, but when downloaded, all the older pictures of one month show a '? ' instead of thumbnails.

  I contacted the support of whatsapp and they say it's a question about iCloud saving... The thing is that if I click on the question mark, it opens in white but you can see the pictures in the small thumbnails, which makes me think not everything is lost...  Help, please!

  Anyone know if I can recover my pictures? That's what I see:

  

  Were the photos you uploaded in your photo stream Whatsapp? If it were, then they don't would not have been saved as photo stream is a function separate iCloud and don't use your iCloud storage. However, pictures Photo Stream are only stored in iCloud for the last 1000 photos or 30 days, whichever comes first, then when the phone is reset, only the photos of Photo Stream iCloud are re-uploaded.

  You can have a lot more photos Photo Stream on your individual before a reset device, but once again, the photo stream (which is located in iCloud), will have only the last 1000 or the last 30 days of photos to download.

  Photo stream is not an album of archives. It's an album of sharing, with the only intention being a common source for 1000 or 30 days of photos to be stored temporarily so that they can be shared with all other devices signed on the same account iCloud.

  Good luck

  GB

• When firefox load it also load another tab for the search engine. How can I remove this where it will load only my start page?

  When firefox load it also load another tab for the search engine. How can I remove this where it will load only my start page?

  You can check the setting of the home page and make sure that it doesn't have a leak ' |'.

  Firefox supports several home pages separated by ' |' symbol.

  • Tools > Options > general > startup: Homepage
  • https://support.Mozilla.org/KB/how+to+set+the+home+page

• 2 emails with different passwords. Firefox will remember only 1 password at one time - when I log into 'A', it will expel password 'B' and visa versa...

  I have 2 different addresses with 2 different passwords. Firefox will remember only a password at the same time. If I log in 'A', I'll have to go the 'B' password, when I go there. If I log on 'A' and then re - enter 'A' (without first having to access 'B'), Firefox remembers the password, as it should...

  Two e-mail addresses in the same field?
  Firefox allows only a single opening on the same server, logons not simultaneous.

  Try to use this extension.
  
  http://Br.mozdev.org/Multifox/

• Hp HP 2542: 2542 will scan only one letter

  Hello

  I have a HP 2542, it's for my dad, he wants to use it only as a standalone Copier, no pc attached, just lift the lid put the papoer to press on print, then get a copy at the other end. How simple is that? BUT the scanner will scan only of letter size and the original is A4 so the end of Moose is off, how do I change the scanning a4 area? This should be so simple and yet I can not find where to change it! I installed the printer on my laptop, but all the settings I found said A4 already, but the printer scans stubbornly letter! I need help before the printer and hurt my foot!

  Hello
  
  Thank you for your time and yes my foot is intact! So the scan size is letter only, well that would explain why I couldn't find where it change!
  
  I think that Mr H Simpson has a word for this... Oh!
  
  Steve