Unable to connect to the internet using the new wifi card.

Similar Questions

• Satellite M100-221: unable to connect to the home WiFi AP

  Unable to connect to the home WiFi AP. Impossible to establish connection (when using intel software Bundle, connection hangs on the authentication step.
  When using the connection and windows engine, it connects 3 times will come down on "acquiring network address").

  I downloaded and installed the latest drivers and updates to the BIOS, but it does not solve the problem. Other computers with equivalent settings to connect without any problems.
  Wireless AP DLINK 1000AP + type b Wi - Fi.

  What is the problem?

  Hello

  When I have this kind of problems, sometimes by turning and the AP help.
  Or try to change the authentication or encryption settings.

  Good bye

• Unable to connect to the virtual wifi

  Hello

  I can not connect to the virtual wifi via android. on my old laptop with windows 7, it works the same way.
  I created it with commands cmd:
  command netsh wlan set hostednetwork mode = allow ssid = "MySSID" key = "Mykey" keyUsage = persistent
  netsh wlan start hostednetwork
  in the connected connections sound also displayed with internet, but when I try to connect with my GNex, his only tries to connect, but cannot...
  I have the Qualcomm Atheros AR8161 PCI - E Gigabit Ethernet Controller (NDIS 6.30) for Ethernet and wifi: Broadcom 802.11n
  OS: Windows 8 Pro
  You need more info?
  Thank you

  Hi Mike,.

  Try the following steps:

  a. click on properties of your data card (if you use it) connection.

  b. click the 5th tab "sharing".

  c. check box on all the options there.

  d. and reactivate your virtual network via the following command: -.
  
  netsh wlan hostednetwork stop
  netsh wlan start hostednetwork

• Satellite A110 - switch WiFi does not work with the new WiFi card

  Hello everyone

  I have a problem with my laptop Toshiba Satellite A110 - 178 (PSAB0E). I replaced the original Intel 3945abg with Intel Link 5100 WIFI card and on the new wifi hardware wifi card switch does not work.

  New wifi card is discovered and drivers to the correct job but when I try to search with the Intel Pro/Wireless software wifi networks I message to turn on hardware switch, but there light and not work. The old wifi card swich works OK - orange light is on. On the new map light is off and swich does not work.

  Help, please

  Hello

  Do you have also enabled the WLAN functionality by pressing FN + F8?
  Check it!

  In addition, I think the case is clear: the new wireless LAN card isn't compatible with Satellite A110.
  So in my opinion, you must use remove the new card Intel and install the old card that works fine in your laptop.

• HP Officejet 6700 Premium: Unable to connect to the new network HP 6700

  I just changed networks and want to connect my HP Officejet 6700 Premium to the new network.

  In the control panel of the printer, I accessed network / Wireless Installation Wizard.  When I do, I get the message:

  Locking function

  This feature has been locked by your system administrator or the person who set up the printer.

  There is an OK button, but no other options.

  I get the same message when I tried to access a WiFi Protected Setup, and, for good measure, the default system restore.

  There is no administrator, in itself, because I'm the one who has set up the printer.  I'm rulnning a MacBook Pro on OS X El Capitan.

  Please, help me to know what I need to do to connect my printer to the network so I can print.

  Thank you very much for taking the time to answer and especially for providing additional resources should what was being offered as a solution to not work.

  I have tried your solution several times and kept getting the same message.  I tried shuttig the printer off by pulling on the power cord, stop in the right way, reverse iin, etc..  Nothing removed the error.

  Then I took the printer to a local Best Buy to show them the problem, which was at home.  We tried it a few times, and then, for no reason whatsoever (seems), it allowed us to do a reset.  No one knows what was different.

  My advice for anyone with the same problem is completely unplug it, let it sit for a while, keep trying and hope for the best.

• locked settings by the adiministrator system and unable to connect with the new wireless network

  I changed my ISP and routers.  I need to change the settings to the new router wireless.  However, when I try to access the network settings on the printer through the screen on the printer, it is said that it is locked by the system administrator.  I am the admin.  Where can I access it without being on the network?  I tried to reset to the default values of factpry, but the same problem exists; It is blocked by the system administrator.

  I was able to solve the problem.  I went through the set up using the USB cord.  Then I switched it to wireless technology.

• Unable to connect to the new user profile failed error user account

  I just created a new user account, but I can't open the new user accout I get an error indicating the failure of user profile, please help

  Hi lol123-179,

  ·         What is the exact error message?

  I suggest you follow these methods.

  Method 1: Follow the steps in the article.

  http://support.Microsoft.com/kb/947215

  Method 2: Follow the steps in the article on how to fix a corrupted user account.

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

• Windows 7 does not connect to the new wifi networks

  I have a problem with connecting to wifi networks. My laptop only connect to wifi networks that I have already connected to in the past but does not connect to all nine. The computer will recognize the but won't give me the possibility to type in any password. For example, I can connect correctly to the House and my moms place as wifi passwords are already saved on my computer. However if I go to a friends house their wifi signal will appear but when I go to connect I will not have to enter a password, the mouse cursor will simply show it to load a few seconds and then nothing happens.

  Can someone help me?

  Hello James,.

  Thanks for posting your question on the forum of the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  What is the brand and model of your computer?

  This problem can occur for the following reasons:

  -WEP, WPA or WPA2 key or password security issues.
  -Incorrect network connection settings.
  -Corrupt or incompatible drivers.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run the network troubleshooting and check.
  Reference:
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  If this does not help, then use method 2.

  Method 2:
  Please use the suggestions contained in this Microsoft support article and check the issue.
  Reference:
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Unable to connect to the VPN

  I can not connect from home (Windows 7 Starter Edition) at the office of the wife (WinXP Home) via a VPN connection.

  Follow-up of the installation a new connection wizard. Unable to connect with the new account (done in the vpn Wizard. Unable to connect with an existing account on the server VPN system either. I am able to connect from another system of home to the system that hosts the server VPN using pcAnywhere.

  Or the other attempt gives an error 800 - VPN tunnel failed.

  Any ideas on where to start looking?

  I can not connect from home (Windows 7 Starter Edition) at the office of the wife (WinXP Home) via a VPN connection.

  Follow-up of the installation a new connection wizard. Unable to connect with the new account (done in the vpn Wizard. Unable to connect with an existing account on the server VPN system either. I am able to connect from another system of home to the system that hosts the server VPN using pcAnywhere.

  Or the other attempt gives an error 800 - VPN tunnel failed.

  Any ideas on where to start looking?

  See this section of the RRAS team blog...

  http://blogs.technet.com/rrasblog/archive/2009/08/12/troubleshooting-common-VPN-related-errors.aspx

  More than likely the XP box is behind a firewall/router which does not pass traffic GRE protocol 47 . You can test the VPN PPTP link by running the test detailed in the traffic VPN PPTP Ping and secitons on this page.

  http://TechNet.Microsoft.com/en-us/library/bb877965.aspx

  GRAP the pptpsrv.exe and pptpclnt.exe programs on the internet or from a CD of XP SP2. If the tests fail work arounds include...

  * Update the firmware on the router to a version known to pass traffic GRE protocol 47.

  * Flashing the router, if supported, with third-party firmware like DD - WRT that supports passing traffic GRE protocol 47.

  * Buying a router known to pass the GRE protocol traffic.

  * Use an alternative such as Secure Shell [SSH] and a free SFTP client such as WinSCP or TBM for secure remote access to files and folders or Remote Desktop/access control to computers on office's LAN.
  MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

• Unable to connect to the shares of the host, Windows XP

  I cloned a VM XP base today.  The virtual machine was no shared folders enabled; I had problems with cloning of a machine with shared folders enabled, if I leave it on this virtual machine, that I keep around just to clone.

  When I try to activate the shared folders on the new virtual machine, I got this error: "could not update performance file sharing status: a message header has been altered or has the version incorrect." and I am unable to connect to the new action.

  I fixed the machine virtual and uninstalled and reinstalled extensions nothing doesn't.

  Any ideas what's happening?

  Version of Workstation 7.1.0 host and the guest XP SP3, update today.

  Hmm, I googled your error and did not find much.  Just some VIX-related stuff, which would be only bite you if you installed programs after the installation of VMware Workstation - of the 'old' VMware 'old' a programs may have installed obsolete libraries for automation of VIX.  Just after installing VMware Workstation/Player shouldn't cause a problem VIX.

  Question, you try to enable the records while the prompt is already on?  If so, what happens if you stop the prompt, select the files and then put on the client?

• Problem connecting to the new remote server

  We recently spent hosting companies and I am unable to connect to the new server.

  Work in Dreamweaver CS5, Mac OS X

  Here are the steps I took:

  -Under 'sites', went to "manage sites", clicked on the current site and press "Edit".

  -Click on "servers", then + to add a new server. Entered all my info in the "Site settings" window

  -When I click on 'test', I get an error message:

  "an FTP error occurred - cannot establish a connection to the host." No response from the server... »

  Any suggestions? Am I missing a step somewhere?

  Thanks in advance for your help

  Try to go to ftp.yourdomainname.com and see if you by entering your username and password allows through a browser.

  If it isn't, your host has really messed up something.

  Or I guess if the change happened fairly recently, DNS cannot have been activated yet and you could always essentially try to log the old servers.

• Unable to connect to the internet using Firefox or IE

  Unable to connect to the internet using Firefox or IE. I can ping other pc on my network home and can ping websites such as google.com. Other PCs on the home network connect without problems. Nothing has changed in the network or the configuration of IE/Firefox. The only change is that I have installed the update to Vista SP1

  Hello

  Stack TCP/IP Winsock settings in Vista has probably been corrupted.

  Journal to this page and scroll down, there are instructions for Vista.

  http://support.Microsoft.com/kb/811259

  Jack, MVP-Networking. EZLAN.NET

• Unable to connect to the internet using a Wi - Fi connection

  original title: wireless connection problem

  My son can connect to the internet with his phone and the ps3, but no more with his laptop

  He was able to connect before on laptop. No matter what he tries, he can't re - connect his laptop to the internet... It has windows 7
  Thank you

  Hi mikecampbell,

  If you are still unable to connect to the internet with a wireless and wired connection, make sure first that the wireless card is turned on. On most laptops, there is a button in the front of the laptop. If you are still unable to connect to the internet, follow the steps described in this document.

• Unable to connect to the internet update version

  I've updated to the latest version 35, but since then, the browser seems unable to connect to the internet. I thought it was my firewall that was blocking the program. I did what was suggested to work around this problem, that is, to remove my firewall and then add it again. But it does not solve the problem. There is nothing wrong with my internet, how am I be able to connect to internet by using IE or Chrome. And I was able to connect to the internet in the previous version of Firefox. Unfortunately, the new updated version is not allow me to. Have no solution?

  It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls

• Unable to connect to the internet - satellite L40 cannot assign IP address

  Hello

  I have 2 desktop (1 - 1 Toshiba laptop) and 1 wired cable adsl INTERNET connection modem airties RT-101. There is no problem using the Internet with desktop XP.

  But when I plug the cable into the Toshiba (vista) Ethernet card, I can't connect to the INTERNET.
  He is unable to assign an IP address, I checked, and there's something blocking the connection I think.

  Please note that there is no problem with firewalls, because they are now closed.

  Hello

  Try to start the command console and use the command:

  Ipconfig / renew

  This should help to refresh the IP address.
  If this is not possible, then some settings must be verified.

  In this case, I recommend reinstalled the LAN driver, then check if the TCP/IP protocol settings are set to automatic.
  Disable all firewalls, check the connection of the new.