Unable to ping router to windows 7

Similar Questions

• Unable to Ping IP across 2 IPsec Tunnels

  Hello world

  Here's the Setup program

  Server1 - layer 2 switch-ASA1 -L2 tunnel-ASA2 -Layer2 tunnel-ASA3- layer 2 switch - Server2.

  Server1 IP 10.31.2.83/28

  Server2 IP 10.31.2.35/28

  Server1 has its default gateway to ASA1

  Server1 can ping the ASA1 but cannot ping the Server2.

  ASA1 is also unable to ping server2.

  Ping 10.31.2.35
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 10.31.2.35, wait time is 2 seconds:
  ?????
  Success rate is 0% (0/5)

  ASA2 can ping the Server2

  Ping 10.31.2.35
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 10.31.2.35, wait time is 2 seconds:
  !!!!!
  Success rate is 100 percent (5/5), round-trip min/avg/max = ms 02/01/10

  ASA2 can ping Server1

  Ping 10.31.2.83
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 10.31.2.83, wait time is 2 seconds:
  !!!!!
  Success rate is 100 percent (5/5), round-trip min/avg/max = ms 02/01/10

  ACL is allowing traffic, routing, crypto card also allows the traffic.

  What else can I check?

  Any help is appreciated.

  Concerning

  Mahesh

  I don't understand what you mean with Tunnel of Layer2. Is it relevant to this question?

  IPsec is involved?

  Do you have any troubleshooting basic Layer 3? Check the routing information?

  (1) the ASA2 has 2 interfaces, one for each tunnel?

  • ASA2 there transatlantic lines?
    • 10.31.2.80 255.255.255.240 to ASA1
    • 10.31.2.32 to ASA3 255.255.255.240

  (2) ASA2 has only one interface for the two tunnels?

  • You same-security-traffic allow intra-interface?
  • If IPsec is involved, understanding Cryptography ACLs on ASA2
    • 10.31.2.80/28-> 10.31.2.32/28 to ASA3
    • 10.31.2.32/28-> 10.31.2.80/28 to ASA1

  The following command will help all three ASAs:

  SH, route

  HS card crypto

  SH crypto ipsec his (look for the counters of packets on the SAs)

  Best regards, MiKa

• Unable to join a homegroup Windows 7 with a network that spans a wireless bridge

  I have two Windows 7 machines that are at the ends of the face of a wired LAN network which connects via a wireless bridge and I am unable to get Windows 7 machines on each side of the brdige to connect to a homegroup created across the bridge.  Perhaps to better illustrate what I mean, here's my network configuration:

  Wireless router:
  Machine from Windows 7 1 (LAN wired to the router)
  Windows XP machine (for LAN cable to the router)

  Wireless Bridge (connect wirelessly to the wireless router):
  Computer Windows 7 2 (LAN wired to the bridge)
  PS3 (wired LAN to the bridge)
  TV (cable LAN to the bridge)

  I use the bridge wireless set up so that I can connect LAN devices wired to the wireless bridge so that they appear to be on the same local network as all other devices on the wireless router (stops to have at home and the bridge wire wireless allows me to expand the scope of all wireless devices I might have).  While all the machines can meet without a problem and I can't even set Windows Media Player to stream video to the PS3 and the TV through its capabilities of DLNA, Windows 7 network mapping server shows not the systems connected to the other end of the gateway wireless as being on the same network (although it shows them); so Windows 7 Homegroup does not see other machines as being on the same network.

  The only thing I can think to do with limitations in TCP/IP regarding a wireless bridge, from the perspective of wireless router all connected to the wireless gateway devices appear to be a device (they all appear under the same physical MAC address as the device only "wireless" that connects to the network is the wireless bridge - who just happens to have three other devices connected to it) even if they are assigned to different (numbers) IP that are in the same subnet, etc.).  So I guess what I'm wondering Windows 7 has a limiation to recognise the devices connected via a wireless bridge?  Has anyone else encountered this problem and found a work around?

  Thank you.

  I had this same problem (unable to connect to a Windows 7 homegroup) on Windows 7 (64-bit) PC behind a wireless bridge using a D-Link DAP-1522 to a D - Link DIR-655 residing on the main network.

  The solution that worked for me was to allow for the "'wireless MAC CLONING ' with 'Source MAC = Auto" on the DAP-1522. "  It also had the beneficial effect of the side to fix a problem on PC behind the bridge where control Panel\All Control Panel Items\Network card cannot display all the network devices.

• Laptop HP 15: unable to connect to the Windows store for updates

  Setting up the new HP 15 laptop.  You seem very well online.  Icon says I'm connected to home WiFi.  But when I try to access the "shop", I said that I am not connected to the internet.  What Miss me?  I don't know what else to say.

  Hi there @ElliottO

  Welcome to the Forums of HP Support!

  I understand that you get an error message when you try to connect to the Windows store. You have problems with other Web pages having the same error, or are you able to navigate normally?

  With a bit of checking, it seems that it's an unusual problem, but there are several causes. Here are a few pages of various related forums that can help:

  Store Windows 8.1 does not connect to Internet - eightforums.com

  problem with connection/app store - eightforums.com

  Unable to connect to the Windows store (Windows, 8.1, 8, RT and Pro) -technet.com

  I can't access the store of Windows 8 -answers.microsoft.com

  hope something is useful for you.

• Pavilion 140 550 - t: unable to connect to the windows service

  Not sure if it's the good advice of post, but here goes.

  Just got the HP computer yesterday and installed Norton Security, Malwarebytes, and Windows Live Mail (do not like the version of Mail). Now, when I start it, I get "Unable to connect to the Windows Service" pop up and WLM crashes when I try to open it. What the DEVIL?

  Had the same problem on the one I just replaced. My laptop became the 'Group Policy' error thing, but I think I fixed it.

  Any suggestions? Windows is a joke!

  If it is Norton Security, then it's a firewall as well and firewalls blocking things, it's that they are supposed to do. So demand for three, you said that this is probably the cause.

  But if you do not want to test it, then try the system restore I've mentioned or reload the image origin, then just put in place the email again and see if it works without the other two installed, first to see if it will work with anything else in the picture.

• SSL security certificate; Server error ping while testing the Ping between 2 Windows servers

  Hello

  I created SelfSSL certificate for a Windows Server to connect to another Windows Server. I have install the certificate using the MMC Console SelfSSL

  (Certificates).  When I run an application to test the Ping between 2 Windows servers... The below error is the result of executing that PING test.

  

  Hope someone can enlighten me on a resolution?

  Thank you

  Try asking in the Windows Server forum:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Unable to play DVDs in Windows Media Player

  Original title: Media Player

  I can't get my Media Player to play my dvd

  Hello

  Thanks for posting your query in Microsoft Community.

  I see from your description, you are unable to play DVDs in Windows Media Player.  I'll be happy to help you.

  Windows Media Player does not support playback of DVD, you need to install additional codecs to support DVD playback.

  Refer to follow the link for more information on the types of media files that supports Windows Media Player

  http://support.Microsoft.com/kb/316992

  You can install plug-ins and Add-ons to Windows Media Player using the following link:
  

  http://Windows.Microsoft.com/en-us/Windows/Windows-Media-Player-plug-ins

  Disclaimer of third party application:

  Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Use of third party software is at your own risk.

  For all windows questions do not hesitate to contact us and we will be happy to help you.

• How can I change to use a wep, tells me is not secure personal wpa running? I have a brand new d link 2680 router & used windows xp 3?

  How can I change to use a wep, tells me is not secure personal wpa running? I have a brand new d link 2680 router & used windows xp 3?

  Wireless security is controlled by the router.

  Download the manual of your router on the following link:
      <>FTP://FTP.Dlink.co.UK/diagrams/Misc/DSL-2680_A1_Manual_EU_1.0.PDF >

  To change to the WPA instructions are on page 39.

  After that, you may need to remove all references to your router on your devices without wire, then re-establisg the connection.   Alternatively, you can change your Secure ID (SSID) as you make changes to the configuration of your router and then reconnect the new SSID for all devices.

  HTH,
  JW

• You can use the ZyXEL NBG-419N router in windows xp

  You can use the ZyXEL NBG-419N router in windows xp

  Hello

  The real question is to know if your wireless device is compatible which should be it that this router has also B and G
  capabilities. Check the Support and the Documentation of ZyXEL. If you think there may be problems (would be unusual)
  Check with the manufacturer of your device WiFi support and documentation.

  ZyXEL NBG-419N
  http://us.ZyXEL.com/products/details.aspx?PC1IndexFlag=20040520161256&CategoryGroupNo=2F39BF6F-E115-4047-A6C9-36833483A7CA

  One of the first things I do with a router is updates of the firmware.

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Need help message' w/error Unable to start the s window media Interface. Make sure you have at least WMP10. »

  I downloaded WMP11 to download another program and I get this message ("unable to start the s window media Interface. Make sure you have at least WMP10. »).  This message appears when I click on the new program and it loads.  As soon as it loads the first program screen appears and displays this error message on WMP 10.  When I click ok it goes, but I can't get the new program to do anything.

  So before asking on the problem of new program, I would like to fix this so it keeps popping up.
  I'm not too calculates saavy so I need clarification.

  Thank you

  Where did you downloaded WMP 11?

  Uninstall WMP 11 and check again the issue. If it stops then reinstall WMP 11.

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Windows-Media-Player/11

  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=8163

• Unable to send email in Windows Mail - error 0x800CCC0D

  When I try to send email from windows mail I'm notified of next error number: 0x800CCC0D. There is also something about the error socket 11003

  [Previous title: unable to send email in Windows Live Mail - error 0x800CCC0D code]

  There is also something about the error socket 11003

  What does 'something on 11003 socket error' mean? It would be much better if you posted the error message full so we don't have to guess what he says.

  Error 0x800CCC0D means that the server is not found. Error 11003 socket is usually a DNS error: the name of the specified server does not exist or cannot be translated into an IP address. Given that you don't tell us which server is involved, it's impossible to think what you need to enter to the place.

  It is quite sure, however, that changing the settings of the server will not help if the server is not found. Juggle with the firewall is dangerous and will not help in this case either. Nor the removal and replacement of the account, except if you find out what server to use name and who enter when add you the account. You could just as easily do this without deleting the account first.

  So - please report it the full error message. Compose a new message of test with a single topic and send it to yourself. When you see the error message, click it to select it, and then use a right click to copy and paste it in your response here.

• Unable to turn on the window Defender, even after that I click on activate the defender of the window. THA page with the tool does not appear...

  Unable to turn on the window Defender, even after that I click on activate the defender of the window on my window vista home premium... The page with the tool does not appear...

  If you have
  one of the following AV, antivirus, programs installed, it will stop your
  Windows Defender. Purpose of these AVs have their own advocates. 2 defenders
  on the same machine will create conflicts.
  Bottom line: it's ok.
  It's normal.
  List of AVs which will stop Windows Defender

  Norton
  McAfee
  AVG
  Microsoft Security
  Essentials

  If you do not have the
  above AV programs, here's how to do to restart Windows Defender:

  Start button > in the search box, type Services > press the Enter key > scroll to find Windows Defender, click on it >...
  topic status , it must be said... Has begun
  under Startup Type, it must be said... Automatic
  If it does not say that, right click on Windows
  Defender > click Properties > to
  Startup type, click on the pointer to the right and select automatic
  to the service status, click Start
  Click OK when finished.

• Error message: "unable to connect to a windows service windows could not connect to the system event." Unable to connect to the network, Windows Vista Home Edition

  Hello

  When I start my laptop there is a long pause between the home screen and the cover page of my office where the message "unable to connect to a windows service windows has no can connect to the system event. I am unable to connect to networks as says "the dependecy service or group could start. I checked some of the solutions to this problem, including the execution of the 'netsh reset winstock' program that did not work. Any advice would be very helpful. Thank you.

  Hello

  It would be a good idea to run the System File Checker tool to see if you have corrupted files

  "How to use the System File Checker tool to fix the files on system missing or corrupted on Windows Vista or Windows 7"

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally made programs, Accessories, right-click guest, and then click run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click allow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  ___________________________________________________

  And Malware scan:

  Search for malware, if necessary using the safe mode with networking.

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 key repeatedly until you are presented with the Boot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Then, download, install, update and scan your system with the free version of Malwarebytes AntiMalware in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  See you soon.

• Unable to connect to a windows service and as no internet connection

  Hello

  According to the title above, please help as I am not able to connect to the internet. I am posting this work...

  After I turn on my computer, I received this message:

  "Unable to connect to a windows service. Windows could not connect to the System Event Notification service. This problem prevents limited forest exploitation form used on the system. As long as administrator, you can go through the system event log to see why the service failed"

  From what I've read of other people with the same problem, I realized that they are able to have the connection to the internet.

  Hello

  1. you remember of any change to your computer before the problem?

  I suggest that you follow these steps and check if the problem persists.

  Step 1:

  Check if the Service Notification of system events is running or not. To check the services

  a. click on start

  b. in the start search box, type Services

  c. click right on - RUN as ADMINISTRATOR

  Check if benefits described has City status and startup type.

  System Event Notification Service started automatically

  Step 2:

  Might as well not connect to Internet is concerned, you can follow these steps and check.

  I suggest that you connect the Ethernet cable and start your computer in safe mode with network and check if you are able to connect to the Internet.

  See also:
  Why can't I connect to the Internet?

  Also valid for Vista.

• Error when you try to connect to games for Windows Marketplace: unable to connect. ID Windows Live ID or the password entered is not valid. Enter your information and you reconnect. Code: 80048823

  Unable to sign in to games for Windows Marketplace

  Sign in to games for Windows Marketplace issues

  This message can connect to everything but the games for Windows Marketplace

  Unable to connect. ID Windows Live ID or the password entered is not valid. Enter your information and you reconnect. Code: 80048823

  Hello RobBurton,

  I suggest that you post your question in the Games for Windows Live forum below:
  http://forums.gamesforwindows.com/t/785.aspx

  It would be best to help with this question.

  Thank you

  Marilyn