Under Vista, make error on blue screen with BCCode: 1000008e

Similar Questions

• Receive an error message blue screen with the instruction on what to get but its double all of the Dutch.

  Blue screen

  Keep getting blue screen last message is ' disable or uninstall all defragmentation or anti-virus disk backup, utility-check disk hard configeration and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.   It's all double Dutch to me, maybe someone can help me and tell me in plain English what to do.  Jackson

  Hi minetbeaugoss,

  ·         Did you do changes on the computer before the show?

  Follow these methods.

  Method 1: Disconnect all external devices, start the computer and check if the problem persists.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

  Method 3: Follow the steps in the article to check the drive for errors.

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.

• Blue screen with BCCode 10F

  man please help! I get the blue screen after I closed gunbound this is the error:

  Signature of the problem:

  Problem event name: BlueScreen

  The system version: 6.0.6002.2.2.0.768.3

  Locale ID: 3082

  More information about the problem:

  BCCode: 10th

  BCP1: 0000001E

  BCP2: 00000000

  BCP3: 00000000

  BCP4: 00000000

  OS version: 6_0_6002

  Service Pack: 2_0

  Product: 768_1

  Files helping to describe the problem:

  C:\WINDOWS\Minidump\Mini101412-02.dmp

  Lee\AppData\Local\temp\WER-171148-0.SysData.XML C:\Users\E.

  Lee\AppData\Local\temp\WERFA64.tmp.version.txt C:\Users\E.

  Read our privacy statement:

  http://go.Microsoft.com/fwlink/
  ? LinkId = 50163 & clcid = 0 x 0409
   
  This information is to type dxdiag on 'RUN '.
  SYSTEM:
  HP pavilion dv6700 notebook PC
  operating system: windows vista edition Home premium (6.0, build 6002) 32-bit
  Manufacturer: Hewlett-Packard
  Processor: Intel (r) core (tm) 2 duo cpu t5550 @1. 83 ghz (2cpus), ~1.8ghz
  memory: 3062 MB RAM
  DISPLAY:
  name: mobile Intel (r) 965 express chipset family
  Manufacturer: company intel
  chip type: mobile Intel (r) 965 express chipset family
  DAC: internal
  memory total approx. : 358 MB
  current display mode: 1280 x 800(32bit) (60 Hz)
  Monitor: generic pnp monitor
  Drivers:
  driver: igdumdx32.dll, igd10umd32.dll
  version: 7.15.0010.1666 (english)
  Date: 2009-02-26 12:34:14
  would be WHQL logo: Yes
  DDI version: 10
  I downloaded the program "bluescreenview.
  and diagnostic tests was:
  dump file: Mini101412 - 02.dmp
  caused by the driver: watchdog.sys
  caused by the address: watchdog.sys + 1230
  description of the file: watchdog driver
  product name: Microsoft® Windows® Operating System
  file version: 6.0.6002.18005 (lh_sp2rtm.090410 - 1830)
  Processor: 32-bit
  plant address: ntkrnlpa.exe + cdabf
  stack address 1: watchdog.sys + 1230
  stack address 2: dxgkrnl.sys + 3d2a4
  battery 3 address: dxgkrnl.sys + 34e6a
  number of processors: 2
  major version: 15
  minor version: 6002
  empty the file size: 142.776
  These files appear in pink and it looks suspicious because of them are pink, the other are all white:
  file name: dxgkrnl.sys
  address of the stack: dxgkrnl.sys + 3d2a4
  address: 0x8fb01000
  address: 0x8fba1000
  size: 0x000a0000
  time stamp: 0x4d383dc1
  time warp: 20/01/2011 08:50:57
  product name: Microsoft® Windows® Operating System
  description of the file: DirectX Graphics Kernel
  file version: 7.0.6002.18107 (vistasp2_gdr_win7ip_dgt (wmbla). 090924-1550)
  full path: C:\Windows\system32\drivers\dxgkrnl.sys
  file name: ntkrnlpa.exe
  address of the stack: ntkrnlpa.exe + b1e8a
  address: 0x82a3c000
  address: 0x82df6000
  size: 0x003ba000
  time stamp: 0x5037809b
  time warp: 24/08/2012-08:24:43
  product name: Microsoft® Windows® Operating System
  file description: NT Kernel & System
  file version: 6.0.6002.18686 (vistasp2_gdr.120824 - 0336)
  full path: C:\Windows\system32\ntkrnlpa.exe
  file name: watchdog.sys
  address of the stack: watchdog.sys + 1230
  address: 0x8fba1000
  address: 0x8fbad000
  size: 0x0000c000
  time stamp: 0x49e01b13
  time warp: 2009-10-04 23:22:43
  product name: Microsoft® Windows® Operating System
  description of the file: watchdog driver
  file version: 6.0.6002.18005 (lh_sp2rtm.090410 - 1830)
  full path: C:\Windows\system32\drivers\watchdog.sys
  file name: win32k.sys
  address of the stack: win32k.sys + 402f2d58
  address: 0x81ae0000
  address: 0x81ce5000
  size: 0 x 00205000
  time stamp: 0x4ff44cfa
  time warp: 07/04/2012 09:02:34
  product name: Microsoft® Windows® Operating System
  description of the file: Multi - User Win32 Driver
  file version: 6.0.6000.16386 (vista_rtm.061101 - 2205)
  full path: C:\Windows\system32\win32k.sys
  I use avira avast antivirus and superantispyware.
  I also went intel.com to see if my drivers were updated, they weren't, so I install 'aware' and I can't tell if my old driver was better or not. I don't know what to do now I fear for my computer to broke so that it recharges
  . I hope that the information I provide enough otherwise ask me specific what information do you need please reply this post :(((.)
  Thank you in advance :)
  HELPPPPPPPPP

  A STOP error 0x10E (BCCode: 10F) is an internal video memory management error.
  In most of the cases I've read on this subject accused the video drivers.

  Please visit http://downloadcenter.intel.com to download and install the latest Vista compatible driver package for your video card and chipsets. (it is probably this download: http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=17407&ProdId=2800&lang=eng&OSVersion=Windows%20Vista%2032 * & DownloadType = drivers )

  If this doesn't solve things, so please start with the free video diagnostics at this link: http://www.carrona.org/addldiag.html

• How fix/stop blue screen with BBCode: 1000008e?

  original title: how fix/stop blue screen of death with the BBCode: 1000008e?

  My laptop started throwing up blue screens of death at random, usually after a minute or so, I have not installed new hardware or software recently, but I accidentally download a virus of frostwire (I know, dumb huh?), that's the problem (at least I think in any case) as what all started after I downloaded it. My laptop has started to go very slowly as take 5 minutes to initialize and my software norton anti-virus has not picked up something on the scan, but since the analysis, he took and destroyed two files I think that they were named hki292.exe or something like that. The blue screen is still but that occur. That's what he says about the error in safe mode, at the beginning it says ECCode has but now its changed to 1000008e.

  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.0.6001.2.1.0.768.3
  Locale ID: 2057

  More information about the problem:
  BCCode: 1000008e
  BCP1: C0000005
  BCP2: 81E3532A
  BCP3: 8AB5782C
  BCP4: 00000000
  OS version: 6_0_6001
  Service Pack: 1_0
  Product: 768_1

  Files helping to describe the problem:
  C:\Windows\Minidump\Mini012211-03.dmp
  C:\Users\home\AppData\Local\Temp\WER-186935-0.SysData.XML
  C:\Users\home\AppData\Local\Temp\WER1E78.tmp.version.txt

  Can someone help me solve this problem? any help is greatly appreciated

  Hello

  I suggest you follow the steps mentioned below.

  Method 1:

  Step 1:

  I suggest to start in safe mode with network and check if the problem persists. Follow the steps mentioned below.

  a. restart the system and keep tapping F8 until you reach the start menu.

  b. Select safe mode with networking from the list and press ENTER.

  Step 2:

  If the problem persists then in safe mode, I suggest you do a clean boot and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135/

  If this does not help then, follow method 2.

  Method 2:

  I suggest to run a SFC (System File Checker) scan on the system and check if the problem is resolved. Follow the steps mentioned in the article below.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

   

  Method 3:

  I suggest you do a start-up repair and check if the problem persists.

  How can I fix a startup (startup)?

  http://Windows.Microsoft.com/en-us/Windows-Vista/how-do-I-fix-a-boot-startup-problem

   

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Blue screen with BCCode 24. Minidump downloaded

  https://SkyDrive.live.com/redir?RESID=A960A7AF01203449%21118

  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.1.7601.2.1.0.256.1

  Locale ID: 1033

  More information about the problem:

  BCCode: 24

  BCP1: 00000000001904FB

  BCP2: FFFFF8800AB07FF8

  BCP3: FFFFF8800AB07850

  BCP4: FFFFF8800184244F

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 256_1
  Thank you!

  TL

  These were related to 360AntiHacker64. sys. Driver Description: 360 Internet Security. Driver update Site: http://www.360safe.com/pc.html.  I remove it and use MSE in its place.

  http://www.Microsoft.com/security_essentials/

  I would also like to run a file system check

  Please run a check of system files (SFC) 

  
  

  All instructions are in our Wiki article below...
  If you have any questions please ask us for .

  Check the file system (CFS) Scan and repair system files

• How can I stop blue screen with stop error code (0x00000002, 0x00000000, 0x804e70ed)

  How can I stop blue screen with error code stop 0 x 00000050 (0xf05c371c, 0 x 0, 00000002 00000000, 0x804e70ed)

  If you are not real tied to the current installation of Windows - then a cloth and then reinstall are the best way to see if you can fix this

  Here's a suggestion on how to do a 'clean ': install
  [quote]
  For testing purposes, it is best to install Windows "clean".
  It is, basically, install the way that Microsoft intended (with the drivers from Windows Update).
  This procedure is for Windows 7, Vista is similar (but has 2 service packs)

  You will need your installation/recovery DVD (s) before you start.  Once you wipe the hard drive, there is no going back!

  1 back up all your data.
  It will wipe everything off of your hard drive, so what you want to keep should be backed up elsewhere.

  NOTE: If this is due to an infection, remember to analyze the data with current antivirus to another system to locate and remove malware.

  2. connect the system to the internet (if the system shows then disconnect from the Internet, do).

  3. use one of these free utilities to wipe the hard drive:
  DBAN ( http://www.dban.org/download )
  KillDisk ( http://www.killdisk.com/downloadfree.htm ).
  This will also remove the system recovery partitions - so the installation/restore DVD is essential!

  4 install Windows by booting from the installation/recovery DVD - DO NOT change any settings!

  5 visit Windows Update and get all updates

  6. check device for all unknown/disabled devices Manager - if there are unknown disabled devices, secure them with the latest drivers from the website of the manufacturer of the device (not the PC manufacturer)

  7 visit Windows Update and download the Service Pack 1 (normally under important updates).  Read these notes for installing SP1: http://support.microsoft.com/kb/2505743

  8 visit Windows Update and get any other available updates

  9 download, install and update a free antivirus, so it does not get infected during the test ( http://www.carrona.org/freeav.html ).

  If problems persist, then the problem is probably with your hardware.

  Warning: If you have an Asus motherboard, check the date on the file C:\Windows\System32\driver\ASACPI.sys.  2004/2005 is a problem, 2009,2010 is OK.  Updates are available on the Web from Asus site.

  Warning: If you have a Sony system, make sure that you do NOT have the 2007 version (or earlier) Extension of Firmware of Sony Analyzer (SFEP.sys).  To update this driver immediately!
  [/ quote]

• Photosmart HP B210a more: HP Photosmart Plus B210a shows a blue screen with error B8145558 and restart.

  For two weeks now my HP Photosmart Plus B210a was wrong to behave. Until that time, I was a happy user, but since it says there is an error in the printer and that I should turn it works again.

  Putting out voltage is actually not possible using the button, as this will trigger a reboot, ending up on the same screen as before. During the start cycle, I have a brief moment where I can access the regular menu before it shows a blue screen with the B8145558 error code. 2 seconds after it is shown, a white screen appears with the title of printer error and the message to reboot.

  So far, I have cleaned the print head and the connections of all dirt and residues. I even managed to start and finish in a copy process, before it gives me the error. However, the error will come, and then it's over.

  Someone has encountered this problem before? Currently, I find only 1 reference to this error in Google and not on this site. Any suggestions that I could try?

  Hi @kootstra,

  From your description, I suspect there is a problem with the firmware that may be irreparable. We can try a reset, but because the printer will not stay on very long main screen until the error appears that we are not able to access the menu of support, we need to reset.

  I'll send you a PM (private Message), but before I do, please see the HP Privacy Statement.

  This privacy statement informs you of our privacy practices and the choices you can make about the way information about you and your online activity is collected and how that information is used. This statement is available on our homepage at the bottom of each web page of HP and HP.com.

  There are a growing number of messages in this forum and elsewhere in the internet with the steps to do a reset on different printers.  Reset to will sometimes fix problems, so resetting is not the issue.

  A few resets require you to enter key combinations to open special menus on your printer that you were supposed to never access.  These special menus are used by developers and staff support for debugging of problems, but they are not intended for inexperienced users and can have unexpected results.  A wrong button push and you might no longer have a printer, but rather an expensive paper weight.  On top of that, if you happen to the 'brick' the printer in this way, it is considered as customer induced damage and voids the warranty automatically. These resets are only intended to be distributed and used as a last resort and under the direct instruction of a representative of the HP technical support. They should not be made lightly!

  Reset the printer: what you need to know

  Please check the little envelope on the upper right of the forums page to check your Inbox of Forums.

  

• Blue screen with the error code and I have no disk recovery for HP Pavilion dv6-1260se

  I have a HP Pavilion dv6-1260se with operating system Vista factory installed. When you start the computer, I get a blue screen with this error message: STOP: c000021a {fatal system error}.

  The verification of a KnownDLL failed.  process ended unexpectedly with system

  a status of 0 x 0000221 (0x007fb9c0 0x00000000).

  The system has been shut down.

  I don't have a recovery disc for this computer.  I tried to order them, but they seem to not be available.  It is my daughter's computer.  She said she started having problems after you download Frost Wire (music sharing), and then she took.  We tried to go back to a bygone era and that did not help and then the blue screen with error message appeared. What should I do now?

  Hi Yprlvr

  It is not possible to download records from the web site, but you can order and they will send you the discs for you.  If you can get another option using F11 to work and get the restored system this way, you can make your own recovery disks (assuming that you have not already done on this PC, what a game can be made by PC).

  R

• Satellite A350 - blue screen with error message

  At the start of windows7, I get a blue screen with error message 0 x 0000116.

  Can someone help please?

  It looks like a graphics driver is a troublemaker. Try to reinstall a graphics driver in SafeMode (f8 at startup). Read this article for more information:

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/eb584685-6b8b-4ad7-B6CC-ae5ee78095fb

  It is for VISTA but should be the same for win 7 too.

• Blue screen with STOP error 0x0000007B (0xBA4CF524, 0xC0000034, 0x00000000, 0x00000000)

  I have my Acer 5920 laptop, 2 GB of RAM and 160 hard drive, last stop system time correctly with all the files to day, but when I restart then comes windows XP Jean-Christophe and then a blue screen with the error. Nor I have install new software or remove something in the laptop. My system was perfect, and that was before the last stop.
  I have Windows XP SP2-teacher-pack. I have the original CD of this package.
  But when I use the CD then nothing is happen and come same messgae of error. I do not have any other CD bootable for windowXP except your originalCD.
  Please suggest me what I should do to fix my probem. I'm not to much expert for the formatting and other things computer.

  After reading your following suggession:
  Here are a few things to try:
  The first thing to do is to boot your system and start pressing F8 as soon as it starts booting.  You will get the Windows startup options screen.  Select "Disable automatic restart in the event of system failure" and let it restart.  When it starts, it can now stop with an error screen and give an error message and code.

  Disconnect all external devices (printers, USB Hub, drives external, etc.) and try to start.

  I got the result of the error that comes on a blue screen after you follow your process-blue screen with STOP error 0x0000007B (0xBA4CF524, 0xC0000034, 0x00000000, 0x00000000)

  Thanks in advance for help
  What about nice Rajneesh

  Just one quick response for others...

  Go to your bios to change the mode of training of your s - ata AHCI or IDE Compatible mode or all that apply :) Windows XP is not like SATA, because it has no native support for it. At the start of the second phase of a Setup program, it would fail with this BSOD.

  Also read the following Microsoft article that describes many other causes (including file system damage):Troubleshooting of errors "Stop 0x0000007B" in Windows XP Advanced

  Sometimes, your BIOS will provide its default settings after a system crash or a configuration. Should not happen, but it is...

  For BIOS-discussions, see: 0x0000007B 0xBA4cf524 - Forum of Support PC - Free Computer help , XP installation: * STOP: 0x0000007B (0xF78D2524, 0xC0000034, 0x00000000, 0x00000000)? - Page 4 - Cyber Tech Help Support Forums , 0x0000007B (0xBA4CF524 - Google zoeken .)

  Have fun, and... Peace!

  Devvie

  ~ ~ ~ * E-mail address is removed from the privacy * ~ ~ ~

  CONARE nullius momenti videri fortasse missilibus careant
  ------
  All the spelling mistakes are my own and may not be distributed under the GNU General Public License! -(© 95 1 by Coredump; 2-10 by DevNullius)

• Blue screen with an error: process1_initialization_failed "stop: 0x0000006B (0xC0000020, 0 x 00000003, 0x00000000, 0x00000000).

  OT: Boot to Vista.

  Hello everyone,

  I have a laptop running Vista which is not booting to windows at all. I tried repair disk installation which stops at a blue screen with an error: process1_initialization_failed

  Lowest:

  Stop: 0x0000006B (0xC0000020, 0 x 00000003, 0x00000000, 0x00000000)

  Y at - there anyone who can help?

  Thanks in advance :)

  Hi Nikita,

  Try the following link that will help solve your problem:

  You receive "0x0000006B" and "0XC000021A" Stop error message after you uninstall McAfee Agent 4.6.2 in Windows Vista, Windows 7, Windows Server 2008 or Windows Server 2008 R2:

  I hope this helps. Please let us know if you need assistance.

• Unable to boot error on blue screen vista window

  Hello

  I use windows vista sp2 on the computer and am unable to initialize properly. I am at a loss for what to do.

  That's what happened. My computer became infected with a nasty virus, so I tried to boot into safe mode. However, I got a blue screen with an error message that says:

  "A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS SHUT DOWN TO PREVENT DAMAGE TO YOUR COMPUTER."

  IF IT IS THE FIRST TIME YOU'VE SEEN THIS ERROR SCREEN RESTART YOUR
  COMPUTER. IF THIS SCREEN APPEARS AGAIN FOLLOW THESE STEPS:

  CHECK FOR VIRUSES ON YOUR COMPUTER. REMOVE ANY NEWLY INSTALLED HARD DRIVES OR HARD DRIVE CONTROLLERS. CHECK YOUR HARD DRIVE TO ENSURE IT IS PROPERLY CONFIGURED AND COMPLETED. RUN CHKDSK /F TO CHECK FOR HARD DRIVE CORRUPTION, AND THEN RESTART YOUR COMPUTER.

  "I want to reformat my computer for Window XP, but after installation of window will display this error and once I started my pc this error appears again...". PLS help... Thank you...

  jpaul08,
  If your system has been infected then the best thing to do is to format the HD ANS reinstall factory default.  According to the PC that you have, you must have a recovery partition or the recovery disk (most use partitions these days).  When start you on the recovery media factory be sure to only select the 'Factory Restore' which will erase the disk and reload the operating system.  The only way that you can switch from Vista to XP is now if the recovery media XP or you own a valid copy of XP retail. Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Blue screen with error message

  Product name: HP Media Center M7250n desktop PC

  Product #ED842aa-aba

  I get a blue screen with error messages asking if this is the first time I get the error and then at the end it says: it is dumping memory. I would wipe my hard drive and reinstall XP but my system is out of warranty and HP gives me a recovery CD. What are my options.

  Hello

  If you are looking to purchase a set of recovery disc for your system, you can visit the site http://www.restoredisks.com/.

  NOTE: This site is not the HP website and it's a third-party site where they provide the recovery for different computer manufacturers disk (they charge for discs).

• HP Pavilion dv7-2160ed - blue screen with error code: 0 x 00000003, 0x86FF8688, 0x86FF87F4, 0x82E2FEC0

  Installed windows 7 - Ultimate (32 bit) and after that, I sometimes have a blue screen with error code: 0 x 00000003, 0x86FF8688, 0x86FF87F4, 0x82E2FEC0

  And I also noticed that some hardware is not installed to properliy:

  1 base system device:
  PCI\VEN_197B & DEV_2384 & SUBSYS_3624103C & REV_00
  PCI\VEN_197B & DEV_2384 & SUBSYS_3624103C
  PCI\VEN_197B & DEV_2384 & CC_088000
  PCI\VEN_197B & DEV_2384 & CC_0880

  Device base system 2:
  PCI\VEN_197B & DEV_2382 & SUBSYS_3624103C & REV_00
  PCI\VEN_197B & DEV_2382 & SUBSYS_3624103C
  PCI\VEN_197B & DEV_2382 & CC_088000
  PCI\VEN_197B & DEV_2382 & CC_0880

  3 base system device:
  PCI\VEN_197B & DEV_2383 & SUBSYS_3624103C & REV_00
  PCI\VEN_197B & DEV_2383 & SUBSYS_3624103C
  PCI\VEN_197B & DEV_2383 & CC_088000
  PCI\VEN_197B & DEV_2383 & CC_0880

  unknown device 1
  ACPI\ENE0100
  * ENE0100

  unknown device 2
  ACPI\HPQ0004
  * HPQ0004

  Can someone help me with this problem?

  Thank you very much. There is a hard drive problem. With the seagate tools, we could solve the problem.

• I put the machine into hibernation and when I restarted, I got a blue screen with stop: 0 x 00000024. Restart gave a different stop error message: 0 x 00000050.

  Original title: Blue screen problems - Stop 0 x 24 and 0 x 50

  I'm not being updated hardware or software on my Dell Latitude D8380.

  I ran the Windows tool to check if the laptop is suitable for upgrading to Windows 7, but did not install any software.

  I put the machine into hibernation and when I restarted, I got a blue screen with stop: 0 x 00000024 (0x001902fe, oxba4f7948, 0xba4f7644, 0xb9d31ae8) ntfs.sys address b9d31ae8 base at bpcef000, datestamp h8025be5.

  Restart gave a different stop error message: 0 x 00000050(0xffffffff,0x00000000,0xba1bef42,0x00000000) i8042prt.sys address ba1bef42 base at ba1b8000, date stamp 48025c 67.

  Please can you help. Thank you, Sue Dixon

  Hello

  Step 1: Check if you are able to boot in safe mode. If you are able to boot into safe mode, and then try to perform the clean boot to safe mode and check.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Step 2: Run the check disk hard disk command. (You will be able to try this step if you are able to start in safe mode or in normal mode with success)

  How to perform disk error checking in Windows XP

  http://support.Microsoft.com/kb/315265

  Let us know the status of the issue.