Similar Questions

• Update firmware on Dell Powerconnect 6248P battery

  Hello

  I need to update the firmware on the switches on my stack, the stack consists of 3 all current 6248P to run version firmware 3.2.1.3 Powerconnect switches.

  I plan to stack in a 4 switch that is running 3.3.1.10 so I need to update my existing carpet before doing this.

  I would like to use auto update and upgrade the firmware on the circuit breaker that will modernize, then the rest of the stack, but the issue I'm having, it's that the documentation Dell tells me to enable synchronization of the firmware using the command "start auto-copie-sw" in the cli, however appears not to exist at all?

  Can someone advise?

  Thank you

  Steve

  The documents listed here.

  www.Dell.com/.../pwcnt_stacking_switches.pdf

  Is a little outdated. Therefore, the listed order is more part of the 6200/CLI firmware. By default, the switch will try and push any updated firmware for the other switches in the stack, no need to run a command.

  See you soon.

• Update firmware 7.7.7 7.6.7

  My airport express and extreme are updated to firmware again offers:

  7.7.7 and 7.6.7 for adults.

  It is not announced and what's inside

  7.7.7: Airport Station of Base of the Firmware Update 7.7.7 Information

  On the Firmware Update 7.7.7 Base Station Airport

  Update firmware 7.7.7 is recommended for base stations all AirPort Extreme and Time Capsule to airport with ac 802.11. This update improves the stability and performance of your base station.

  This update:

  • Resolves an issue that may prevent communication between clients on the same network
  • Improves performance with an extensive network of comments
  • Resolves conflicts of potential names with Hello sleep Proxy

  For more information on updates firmware of base station at the airport, including instructions how to install the update, please visit: http://support.apple.com/kb/HT1218

  7.6.7: Airport Station of Base of the Firmware Update 7.6.7 Information

  On the Firmware Update 7.6.7 Base Station Airport

  Update firmware 7.6.7 is recommended for all Apple 802.11n Wi - Fi base stations including AirPort Express, AirPort Extreme, and Time Capsule from the airport. This update improves the stability and performance of your base station.

  This update:

  • Resolves an issue that may prevent communication between clients on the same network
  • Improves performance with an extensive network of comments
  • Resolves conflicts of potential names with Hello sleep Proxy

  For more information on updates firmware of base station at the airport, including instructions how to install the update, please visit: http://support.apple.com/kb/HT1218

  For more information on the use of products from the airport, go to the Support Page at: http://www.apple.com/support/airport

  Kind regards

  Shawn

• Update firmware on Satellite A200-1gh - noise emissions under Linux

  Hello

  I have a serious problem with the sound on Toshiba laptop. Many people have the same problem I have.
  An example:

  ________________________________________
  Hi there everyone
  straight to the point, I got no sound running ' bt3 beta computer laptop - Toshiba satellite a200 - 14 d, HD audio - Realtek ALC862 @ Intel 82801GBM ICH7-M - audio. I tried to fix it with a blender Kmix or alsa, even downloaded the Realtek driver name and installed, but bt3 built in Realtek driver. Still nothing"
  ________________________________________

  My laptop contains this sound card: 00:1 b. 0 Audio device: Intel Corporation 82801 G (ICH7 Family) High Definition Audio Controller (rev 02) @ Realtek ALC861-VD. There is a problem somewhere in the firmware of this map or the Linux kernel.

  We use Backtrack 3 who is Slax based Linux distro.
  I've been with many professional talking about Linux, Bud, no one is really sure what is the problem. They said several things to try; one of them is updated firmware. I've never done this before, I'm looking for help.

  Number of exact model of my laptop is Toshiba a200-1GH psaece

  Please help if you can

  > There is a problem somewhere in the firmware of this map or the Linux kernel
  What are you talking about boyfriend? This firmware of the sound card that you hear?
  I think you're confused.

  First of all there is NO firmware for the sound card. Second, the sound card is controlled by sound driver.
  Always is it that Toshiba laptops are preinstalled with Windows OS.
  Linux is not supported at this time, and you won't find driver for sound card for Linux.

  If you need a sound driver for this sound chip, you will need to download it from Realtek Web site!

  That s all about your firmware to his mysterious map.

• Satellite A45: need to update firmware on DVR K12D drive

  Hello...
  IM new here... Well, I have a toshiba > Satellite A45 Series... which had a DVD Multi Drive (DVR K12D) inside. The problem is that his operation stopped. Sometimes she would write a CD then sometimes it spoils my CD. I used on the media player were Verbatin, Imation, Supermedium, Sony.

  Well the reader works as a very short period and then dies OFF... every time I took it to the repair center...

  The drive has been changed now 4times by toshiba support. I asked for the release of Firmware from 1.05 to 1.15 or higher. They keep answering back telling me to ask pioneer. But it is an OEM obvious by toshiba.

  The player after having been changed stops working without delay of 2 to 3 months max 4 months time and den customer tried upgrading the drive by putting a higher config recorder multi disc double tht is the 8 GB one. The satellite detects that hardware.

  been 2 years now my readers send me problems such as:

  does not read DVD
  doeant read CD RW
  don't write CD/DVDs
  sometimes DVD detects any sometimes they detect its weird.

  The only solution is to update the firmware, but how can I do? I need the update of the firmware. I called toshiba WE also, they talked for two hours and then answer that I have to contact pioneer!

  Please help me!

  Vik!

  Hello

  CD/DVD players support generally not all means.
  As far as I know in the manual you will find a list of the CDs and DVDs is supported and it works properly.

  In addition, it seems that this device was designed for an American market and in this case, you should look at the Toshiba Site us.

  I checked this American site:
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_sc_home.jsp

  There, I found several notebooks A45 and the necessary drivers. I also found a driver for DVD rom and ram. It s not a firmware update but maybe it helps.

  However, on Toshiba Europe site, I found several updates firmware for the readers and the different European books but as I said at the beginning you have a US laptop and have to look on the American website. If you don't get an update of the firmaware if you ask the manufacturing of the car.

  In addition, I want to say that you can not be sure that, after updating the firmware of the player will not work correctly. This kind of malfunction looks like a defect of lens calibration and therefore only a replacement disc can solve this problem.
  If the drive has been replaced several times so I guess that the guarantee is valid and you will get a new.

• jumble of text in the web interface after Web Services update / firmware

  I received a message on the screen of my Officejet 6700:

  Update recommended

  An update is available for Web Services (ePrint and Apps).

  Do you want?

  I chose to update now and it installed fine, or so I thought.

  I checked the web interface of the printer, and there is a bunch of text confused, as the code is messed up for the web server.

  I had just finished to check the status of your ink cartridges (and subsequently replaced a), so I have the fully functional Web page fortunately still open on another machine, so I can tell exactly what is forward - after on this page.

  On the tools > gauge of ink page, on the right page (old) the said table (title, first line, first column):

  Cartridges installed

  Color | Magenta | Cyan | Yellow | Black

  Part number

  Type

  End of warranty date (A-M-J)

  First Installation Date (A-M-J)

  Area of ink

  USE

  HP

  But after the software update, it says this:

  Print the self-test Page

  L@S#0456 | Number of recorded events. L@S#0462 | L@S#0552 | L@S#0450

  Use of the accumulated media

  Date

  L@S#0477

  L@S#0561

  L@S#3345

  In addition, the order "supplies" link, with a contextual text of "print order supply."

  now, says "Cartridge", with a contextual text ' block unwanted faxes '

  And "Print Printer Status Report" now says "L@S#2567".

  I went to the support section and found an update firmware, but during download and execution, after you find the printer, he says that he is already up to date and leaves me not choosing to try and reapply the update of the firmware (as is obviously what is happening through the touchscreen menu has already done).

  Should I just restore to factory settings? I think that firmware would not be changed by doing this. It is not an older version of the firmware available on the product support page, to return to an earlier version.

  Via the screen menu touch printer, a Printer Status Report print indicates the firmware version is MPM3CN1322DR.

  How to force a reinstallation of the firmware, or let them difficulty firmware which was released on 25-06 - 2013?

  I've been using Google Chrome and even had 2 tabs open in the same window, one from before the update and the second I opened after the update, so this was not a factor.
  
  I had not revisited the web interface of the printer to date, and currently, I see that the problem has disappeared!
  The version of the firmware has not changed, and I did no manipulation of the printer. I also highly doubt that the main user has nothing, because it is not tech savvy. So, the problem seems to have corrected itself.

  The only thing I see now, that I did not notice before, is that there is a version of firmware fix, but it currently says 0. I don't know what it was before, but I guess zero means that there is a patch, so the firmware didn't automatically update in order to make the problem disappears.

  Problem disappeared, but I don't know how or why. I haven't decided if I will update the second printer that is the same model.

• Impossible to update firmware on mac mini without CD

  I'm unable to update firmware on mac mini without cd-rom.

  I tried to burn iso image to USB via disk utility, but folowwing error:

  "Unable to validate the source - invalid argument.

  Can you provide iso correct or dmg that can be used with the mac disk utility as seems that I don't have a way to upgrade the ssd firmware now?

  P.S. I tried unetbootin on win and mac, tried to copy the iso contents with dd in terminal but mac still do not see my USB stick on the charge.

  After dozens of solutions on I finally took ssd at my mini mac, put it in the HP laptop with cd-rom, update firmware and restore mini. Thank you apple for sucky usb support and sandisk for silence loading...

• Y at - he liked an update firmware for the sansa clip

  If I use the sansa updater it detects it as a normal element and gives me a firmware to install, one that ends in 32 I think, but if I install what I think ill ruin the clip, so I ask if a firmware update for the clip more were released, I got V01.01.05A firmware now

  No update firmware at the moment; you have the most recent.  If/when an update of the issues, it is likely is displayed as a sticky thread at the top of this forum.

• Update firmware CM1415

  Update firmware CM1415 malfunctions. (CM1410 MFP series FW Update 20120629)

  After a few minutes the wireless connection is lost.

  I use e-print, or fax function, the same thing happens. Lost wireless connection.

  Not possible to use ePrint settings.

  'Lost' mode it is not possible to print reports, etc.

  If I turn on and turn on the printer it works for a few minutes, then returns to the error state.

  Where can I find more old firmware to reverse and to have a functional printer?

  Thanks for your tip!

  While preparing for the partial resetting, I found under network settings > reset to the standard network settings.

   

  
  After that I've reconfigured the network and now it seems stable. I see that it stays on if I do the reset.

  Thank you.

• Impossible to update firmware H310

  As the title says, I can't update my card H310 raid with this firmware:

  Reference Dell PERC H310 Adapter Firmware version 20.13.2 - 0006

  If im using it says my system is not supported for windows and Linux, he just spits it;

  0

  and then nothing happens.

  I tried several different computers with attached disks and not attached to the controller.

  In fact I just managed to update my latest firmware A10 H310 card using this guide which has a download link to all the necessary files in a convenient zip. :)

  Edit: darn it looks like I'm not allowed to post links, so just do a google for 'come back your Perc H310 to its firmware Dell' and you can find good WordPress blog.

• Unable to update firmware Laserjet CM1415fnw

  Hello

  I tried several times to update the firmware on my printer HP LaserJet CM1415fnw.  I get the happy face after the utility.

  The Firmware datecode remains to 20111215 even after I use the utility to update the firmware in the 20120629 date.

  The PC that I use is Windows 7 64-bit OS.  (I tried 3 different PC with the same result.)

  This who can I try to fix this?

  Thank you

  Hi Wamer_ca,

  From the control panel:

  1. tap on settings

  2. press on Service

  3. press on the RFU.

  4. highlight on, then press ENTER to set.

  Try to update the firmware again and let me know what happens?

  Installation instructions

  Flash Firmware Update Notes:
  The firmware update utility uses the network or a USB connection to the printer.

  • HP Color LaserJet Professional CM1415 MFP series printer driver software must be installed before using this utility.
  • The HP Color LaserJet Professional CM1415 MFP printer must be on and in a READY State, as indicated by the LCD screen of the control panel and remain under tension during the process of updating entire firmware.
  • 1415fn HP LaserJet Pro printer MFP series CM color must be connected and able to print documents from the computer.
  • The RFU on the control panel (Service-> RFU) must be set to 'ON'
  • Depending on the speed of your PC processor, the firmware update process may end on the printer before the end of the progress bar to update status in the utility to update firmware flash on the screen of the PC, it's normal.
  • Once the update process has started, do not use your PC for other activity, until the process is complete.
  • Do not power cycle the product or the computer until the firmware update process.

    Process:
    1 download the update firmware from HP.com flash on your desktop.
    2. turn the printer power off and then back to the main printer clear memory.
    3. make sure that the RFU on the control panel (Service-> RFU) is set to 'ON'.
    4. double-click on the file of the firmware flash update utility. It will open a window of the HP firmware update.
    5. Select the correct driver from the HP CM1415 MFP series in the dialogue window. If you have assigned a different name for the HP CM1415MFP, choose the name that represents the correct printer. 6. click "send the Firmware" when you are ready to move forward.
    7. the progress bar will start to move to the right indicating the transferred information.
    8 power cycle are NOT the product or the computer that during this process or the product may become unstable and or unusable without further attention of HP. The firmware flash update can take up to 5 minutes to complete. Please be patient.
    9 in the flash firmware update product, display on the product control panel will display "Print Document - delete - programming - complete - Hewlett-Packard - loans - initialization - Ready". Once the download is complete, the printer is in the ready state.
    10. at the end of the update of the firmware, the dialog window displays a smiley face. Click exit.
    11. the firmware flash update process is complete.

  12. If you want to check the update, use the menu of reports under Setup Control Panel to print a configuration report. The configuration report displays the current firmware revision in the block of product information. If the firmware datecode don't change, check the setting of the RFU in the Service from the control panel Menu - it must be 'ON' for a successful update.

• Update Firmware of BMC R610 of linux

  Hi mates,

  I need to update a few R610 servers, I would like to only update the BMC Firmware if possible without shutting down the machines, is - it possible? I'm running debian on these machines.

  I open it because I've been Googling much this and I found that maybe there are several ways to update the firmwares of server, including the iDRAC completely update, etc., but I am only interested to get the latest patches of cooling, so I guess that should be only update BMC.

  Could you please some direct me in the right direction? I looked and I found some binary files in dell FTP, but I need to be sure of where to find the correct firmwares for my machines and what is the most common method through linux so far.

  Thank you comrades, I appreciate the help.

  Hello

  There is no separate BMC firmware in R610. You need to update firmware iDRAC who BMC features as well. Down, you can load the latest firmware iDRAC at the bottom of the location

  http://www.Dell.com/support/drivers/us/en/04/DriverDetails/product/PowerEdge-R610?driverId=63KCR&osCode=NAA&FILEID=3287900761&LanguageCode=en&CategoryID=es

  You can update the firmware iDRAC without stopping or restarting the system. As you have debian on these machines, I recommend you update iDRAC using Web GUI. You can check below link with a video on the updating of the process. First half of the video is on the download of the image that has changed a bit. You can download the File Format 'Application' link above.

  http://en.community.Dell.com/TechCenter/systems-management/w/wiki/3206.updating-DRAC-firmware.aspx

• There is a maximum amount of hosts for Cisco SF300?

  Hello world

  I m using a Cisco (SRW224G4P) SF300 in my network and I m using Vlan´s.

  I m a lot of loss of packet´s in the network and the users are facing in the absence of performance.

  There are altogether seven switch´s in the network, 6 SF200 Cisco as 'access' switch´s and 1 Cisco SF300 as the 'core' switch.

  It has almost 170 devices connected to the network, mainly IP cameras, other devices are the DVR´s and the NVR´s, a server a certain stand-alone.

  Thing is I m, including the loss of packet´s, and I found this alarm in the SF300:

  2147480831 2012-Jul-06 13:14:45 % of IPFFT-W-SFFTREDYELLOW warning: IP SFFT Table Overflow, aggregated (1)

  2147480831 2012-Jul-06 13:14:45 % IPFFT-W-SFFTREDYELLOW WARNING: IP SFFT Table Overflow

  Some people say this switch (SF300) support´s only 100 guests and that s why I m get this alarm and lose packets.

  But I can't find the limit of host´s in the specification of the switch in any document from Cisco.

  Think you on this?

  There is a limit of 100 guests for this switch?

  Thanks in advance!

  Carlos

  Hi Calavalle, the module layer 3 can only the hardware switch 100 until it starts to change software. The switch can support up to 510 IP addresses but anything over 100 have wait performance degradation.

  -Tom
  Please evaluate the useful messages

• Update Firmware EX60

  I have an EX60 but you must update Firmware before I can get it added to my network.

  I downloaded the upgrade, but am not sure how you install.

  Connect to your network for the few minutes it would take to download the software would be much easier than other methods because they will ask you to go through a tedious process of connection to the endpoint manually through the console cable.

  You can upgrade the EX60 via a TFTP method using your computer, see download-tftp-server-review-2.  Another document that describes the TFTP method is troubleshooting-ex-series-mx-series-sx-and-c-series-codecs count of 128 pg.  You will need to connect to the EX60 using a serial cable special, below is two methods of manufacturing such a cable.

  ex90-making-console-cable-and-consoling

  ex90-make-console-cable-using-ca42-usb-data-cable.

• Problem updating Firmware emulex card (FCoE) thought a single Manager command

  vCenter 4.1

  ESX 4.1 update 2
  

  OneCommand Manager 5.2.12.2 - 1 < < install on ESX using esxupdate

  CIM provider < < install on ESX with rpm

  OneCommand Manager for VMware vCenter 1.1.0 < < install on Virtual Center
  
  I want to update Firmware to troubleshoot vMotion between esx host
  

  Firmware OCe10102 and Startup Code
  Notes: You need to update the firmware and boot code on the OCe10102 UCNA when you install the driver.

  http://www.Emulex.com/downloads/Emulex/firmware-and-boot-code/oce10102-UCNA-firmware-and-bootcode/firmware-and-boot-code.html
  

  any idea?

  Error message

  
  

  
  

  
  

  Hello ianeme,

  I was watching the forums and came across your question. Ask yourself if you have solved your problem of port when you use plugin manager of OneCommand to vCenter Server? I have seen that HP has two downloads for the fw updates. For now, the last FW update to CN1000E is 4.0.493.0 March 12, 2012. Call the Emulex support if you experience problems when you try to update the fw with the Emulex OneCommand Manager application or the plug-in. But just make sure you are tested and approved HP FW by downloading the files from their site.

  Thank you

  Alex

  http://www.Emulex.com/the-implementers-lab.html