Similar Questions

• L26500 61i: PROBLEM UPDATE FIRMWARE L26500 61i

  I can't update firmware. My latest firmware is 11.0.0.2 and when I try to upgrade to 12.00.00.5 I get this message

  SP - SP_12_00_00.5_mvl40 - x 86 - opt_B.signed.fmw: there are problems with the firmware file and the firmware update process has failed. The file you have selected may not be good, or the problem may be due to a transmission error. Please, start the firmware update process again. If the problem persists, please contact support.

  I tried to download it again, but it's the same thing...

  I have checked the connections on the back of the printer and found a LAN connection, I confused with the 360 LaTeX, sorry my mistake
  Another task to do, run the diagnostic menu of emergency update firmware.
  If issue still continue, run the hard drive recovery in the same menu

• Problem updating firmware TS-L632H on Satellite P200D

  Help, please.

  Having problems burning CDs / DVDs. thought the TO01 to TO02 firmware update would solve the problem, but then the TO02 driver could not be installed.

  I tried installing the driver but the software indicates the latest version of the software is already installed.

  Driver date: 21/06/2006
  Driver version: 6.0.6001.18000

  Hello

  I checked the driver Toshiba section info page more (he s right) and are found some details about this firmware update.
  Changes have been made to correct the following:
  Impossible to burn songs on iTunes to some CD media. iTunes error "the attempt to burn a disc fialied. An unknown error occurred (2131)"is displayed

  If the update of the firmware doesn't solve all problems with burning CD/DVDs!

  I assume you have some CD and DVD burning issues because the media are not entirely compatible.
  What you could do is to check various CDs/DVDs from different manufacturers.

  A single note; If I m not wrong not the user manual should provide some details on CD and DVD compatible and supported.

• Problem updating Firmware of the Module e/s

  All,

  I'm trying to update the firmware of the i/o Modules of 1.3.1p to 1.4.1i.  I downloaded the firmware and when I activate it I choose to ignore the compatibility tests.  The module IO then resets and goes through a process of restarting.  After a little while the State is ready but the firmware running is always 1.3.1p.  I also tried by choosing to place it in the start menu to the top only and then reset the module e/s, but the results are the same.  This happens on two modules e/s.  Interface cards and the MMIC both updated without problem, but I'm stuck at IO modules.  Anyone encountered this?  Does anyone have ideas, what may be the problem?

  Thank you

  Ken

  The IO modules get updated at the same time as the fabric of interconnection when they reload and upgrade.  Upgrade one restart of the IF that and the i/o module should be at the same time.  Note that in the activation page you should see in the meantime "rebooting" next to the modules of e/s for this fabric before restarting the FI.

• Problems updating Firmware 7 IDRAC

  Hi, I had problems with my controller IDRAC PowerEdge T320. It seems to be a known issue, introduced with Firmware version 1.50.50, which is delivered with my machine. Basically, the device signals that all user sessions are used. (RAC0218). I am running Windows 2008 Server R2. To resolve this problem, I find the IDRAC firmware update version for my system. 1.57.57 downloaded the windows EXE file and it ran. The release notes say that a reboot is not necessary. At the end of installation, I got a message in a dialog box. "" Device iDRAC7, Application: iDRAC7 could not access Virtual USB Device "and then the following message in the upgrade of the firmware Installer information window" "" This message can be ignored"with many things on the R2 IPMI driver. My problem is that the Dell OpenManage Server Administrator noted the old firmware version number. I reset the iDRAC from the C: prompt to soft help from "racadm racreset" who have reported success. It made no difference. I emptied my cache of browsers as well. Any ideas how can I know if my firmware has actually been upgraded?

  When I googled the error message my own post came first on the list!  So I thought that I had better do a update.  After finally move to try to solve this problem (again), I opened a case of pension with DELL.

  There is now another more recent version if the firmware of the iDRAC. 1.66.65

  I downloaded and installed, but it failed with the same error on "Failed device to access virtual USB".

  The nice guy of support counted Dell that it is due to an incompatible BIOS version.  I currently have 2.0.22 and the latest version is the 2.3.3.  Then I spoke for her.

  I have successfully installed the BIOS update, requiring a reboot.  I then had another go to the update of the firmware to iDRAC to 1.66.65 and this time it worked WHOO HOO!

  Now wait us and see if real problems connection problems are solved.

  I'm quietly confident.

  Hope this helps someone else

  David

• Problem updating firmware on LaserJet 4100

  Hi all

  Looks like I can put my subject in the wrong forum. I have no doubt I should have put my question here in the forum of firms. If someone could take a look at my problem and update (here or here, I subscribe to two topics), I'd be happy.

  https://h30434.www3.HP.com/T5/printing-issues-troubleshooting/LaserJet-4100-firmware-unable-to-updat...

  If an admin can move my post on this forum (or anywhere where it belongs) so that the right people see I understand that too!

  Sorry, new to these forums and forums of discovery of the 'user' before I found the forums 'enterprise '.

  Thank you

  -Derek

  Hello Derek Cunningham, I am an engineer of the HP technical support. I am taking the floor for me and not for HP, but I believe that I can help you.

  Well, it took some searching.  The latest version of firmware that I could find was little out August 2, 2003 (version 1.040.2) part No. C4168-67907 listed as "HILL of DIMM KIT - ROCK".   That said, as of March 31, 2009, the product is no longer a support and spare parts may no longer be available.  I gathered this information by your request directly - however, don't believe not that the firmware update will solve the problem of 'page spew' reported.  I went through the list of firmware for different DIMM firmware versions fix and see nothing corresponding to your symptomatic behavior.

  If your workflow printing is to point and print (customers who print via a print server) Please ensure that the server and clients pilots match.  You can always remove the printer connection client and restore to ensure that binary correspondents sells.  Driver version is important, because the old specific drivers are not supported or even stable with current operating systems.  I suggest you switch for the driver of Microsoft OS Inbox for testing.

  Suggestions were made to try to PCL 5 or PS, I think that the essential thing here is to make sure you are using the latest driver for your product and the OS.

• Digital TV suddenly does not work. Problem updating firmware?

  Hi everyone, I hope someone can help!

  A few months ago, I bought my Bravia Sony 4 K KD-43X8309C at the beginning of August and it worked great. Everything has been fine. I'm going to turn it on this morning (Sept. 30) and have no digital TV, the picture is just empty. TV otherwise works great, Internet, YouTube/Netflix is all good, just Digital TV. Strange I never changed any settings.

  I did some research and realized that today ' today is the release of the new Firmware which I think my TV has automatically downloaded and now not working not just for some reason any. Is there a problem with the Firmware as its quite by chance that the problem started exactly when it was available. I hope you can help!

  All fixed, I went into settings/Factory Reset and erased all settings and put in place from the beginning. Must not uploaded the Firmware correctly but made the second time around.

• iPad2 and problem with the SIM card after update

  even after the 9.3.1 last updated continuously having problems with SIM TIM card network.

  I changed and I tried with another SIM card but the problem remains.

  I did have all those problems with 9.2.1.

  Apple could intervene and solve these problems? Otherwise, I think it's better to make a return to the old 9.2.1.

  Thank you

  Do you see the network? and is it strong enough?

• problem updateing network card driver

  OK, my problem is that I can not update my network card drivers, it say found update failed to install the access file can not possible due to being used by another process I also have to download it to my desktop but cannot install, same reason, update (Wireless LAN_Atheros_7.6.0.172 Vista x 64 Vista x86_A) , they say everything that causes this problem prevents me to install my viper internet security and help my usb stick also.any mass storage usb not recognize?
  Following in the DRV log error message:

  (EE) Error calling SetupCopyOEMInf:? -> Z, State = 0x20
  (EE) Setup of the network, the INF file error: C:\Program Files\GFI Software\VIPRE\drivers\sbfwim.inf PNP ID: sb_SBFWIMcl hr: 0 x 80070020
  (EE) Component Setup error, INF file: C:\Program Files\GFI Software\VIPRE\drivers\sbfwim.inf PNP ID: sb_SBFWIMcl hr: 0 x 80070020
  (EE) Error in InstallIMFile: status 0 x 57
  (II) delete the service: SbFw
  (II) delete the image file of the driver: C:\Windows\system32\drivers\SbFw.sys
  (EE) Error SBFWIM_InstallDriver
  (EE) Install the drivers failed (87) remains of AVG found on the machine.
  -Removal of AVG Ran tool
  -always impossible to install.
  -A tried to update driver and it does not:

  "The process cannot access the file because it is being used by another process".

  -Probably impossible to install this same reason VIPRE.

  Hello

  I suggest you try these methods and check the status of the issue.

  To solve the problem of installing Viper internet security:

  Step 1:

  Run the fix it.

  Problems with programs that cannot be installed or uninstalled.

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall

  Step 2:

  Keep the computer in a clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7.

  http://support.Microsoft.com/kb/929135

  Note: Please, go to step 7 of the Kb to maintain the computer to a normal startup after you fix the problem.

  Step 3:

  Disable the antivirus software and try to install the application.

  Disable the antivirus software.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  To set the update driver wireless.

  Method 1:

  Hardware devices do not work or are not detected in Windows.

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2:

  Update a hardware driver that is not working properly.

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• ThinkPad E220 "Critical battery problem" even AFTER updating firmware of the battery

  Hey,.

  I am owner of a Thinkpad E220 (5380-CTO) and the "Lenovo Thinkpad Toolbox" gives me daily alerts that I have a "critical battery problem". The link takes me to a page to download and update the firmware of the battery. "Updates to the Firmware of battery for hand and slice batteries (external) - ThinkPad Edge E220s, E420s Edge, X 1" http://support.lenovo.com/en_US/detail.page?DocID=HT062049&AID=10429688&PID=3719336&CJURL=http%3A%2F...

  I went through all the steps to update the firmware numberous times, including making the recalibration of the battery and I STILL get the daily 'critical battery error message '. Please help, the daily scans eat up RAM and it's annoying that I have to cancel every day.

  The battery, from what I can tell, works otherwise.

  Thank you!

  Hi all

  Just to give you an update. Our side engineering has tested and managed to reproduce the problem in their labs. They can confirm that by uninstalling the box to Lenovo tools and installation of the currently supported ' Lenovo Solution Center ' as a brand already proposed forum solved the problem.

  The "Lenovo Solution Center" can be downloaded from the link below.

  http://support.Lenovo.com/en_US/downloads/detail.page?&LegacyDocID=MIGR-73784

  Do give it a shot and let us know.

  Concerning

• update of credit card problems

  Hello

  I've updated my credit card today at 5 pm (Paris time), and I really need to work that night because my work needs to be done for tomorrow morning.

  This is a chance I can access indesign cc 2015 tonight.

  Thank you.

  Hi Mary,

  I see that you have updated your credit card information today and it has been updated successfully and your account is good to go.

  Yes, you can start using indesign cc now, there is no interruption of service

  Kind regards

  Sandrine

• Update firmware on Satellite A200-1gh - noise emissions under Linux

  Hello

  I have a serious problem with the sound on Toshiba laptop. Many people have the same problem I have.
  An example:

  ________________________________________
  Hi there everyone
  straight to the point, I got no sound running ' bt3 beta computer laptop - Toshiba satellite a200 - 14 d, HD audio - Realtek ALC862 @ Intel 82801GBM ICH7-M - audio. I tried to fix it with a blender Kmix or alsa, even downloaded the Realtek driver name and installed, but bt3 built in Realtek driver. Still nothing"
  ________________________________________

  My laptop contains this sound card: 00:1 b. 0 Audio device: Intel Corporation 82801 G (ICH7 Family) High Definition Audio Controller (rev 02) @ Realtek ALC861-VD. There is a problem somewhere in the firmware of this map or the Linux kernel.

  We use Backtrack 3 who is Slax based Linux distro.
  I've been with many professional talking about Linux, Bud, no one is really sure what is the problem. They said several things to try; one of them is updated firmware. I've never done this before, I'm looking for help.

  Number of exact model of my laptop is Toshiba a200-1GH psaece

  Please help if you can

  > There is a problem somewhere in the firmware of this map or the Linux kernel
  What are you talking about boyfriend? This firmware of the sound card that you hear?
  I think you're confused.

  First of all there is NO firmware for the sound card. Second, the sound card is controlled by sound driver.
  Always is it that Toshiba laptops are preinstalled with Windows OS.
  Linux is not supported at this time, and you won't find driver for sound card for Linux.

  If you need a sound driver for this sound chip, you will need to download it from Realtek Web site!

  That s all about your firmware to his mysterious map.

• jumble of text in the web interface after Web Services update / firmware

  I received a message on the screen of my Officejet 6700:

  Update recommended

  An update is available for Web Services (ePrint and Apps).

  Do you want?

  I chose to update now and it installed fine, or so I thought.

  I checked the web interface of the printer, and there is a bunch of text confused, as the code is messed up for the web server.

  I had just finished to check the status of your ink cartridges (and subsequently replaced a), so I have the fully functional Web page fortunately still open on another machine, so I can tell exactly what is forward - after on this page.

  On the tools > gauge of ink page, on the right page (old) the said table (title, first line, first column):

  Cartridges installed

  Color | Magenta | Cyan | Yellow | Black

  Part number

  Type

  End of warranty date (A-M-J)

  First Installation Date (A-M-J)

  Area of ink

  USE

  HP

  But after the software update, it says this:

  Print the self-test Page

  L@S#0456 | Number of recorded events. L@S#0462 | L@S#0552 | L@S#0450

  Use of the accumulated media

  Date

  L@S#0477

  L@S#0561

  L@S#3345

  In addition, the order "supplies" link, with a contextual text of "print order supply."

  now, says "Cartridge", with a contextual text ' block unwanted faxes '

  And "Print Printer Status Report" now says "L@S#2567".

  I went to the support section and found an update firmware, but during download and execution, after you find the printer, he says that he is already up to date and leaves me not choosing to try and reapply the update of the firmware (as is obviously what is happening through the touchscreen menu has already done).

  Should I just restore to factory settings? I think that firmware would not be changed by doing this. It is not an older version of the firmware available on the product support page, to return to an earlier version.

  Via the screen menu touch printer, a Printer Status Report print indicates the firmware version is MPM3CN1322DR.

  How to force a reinstallation of the firmware, or let them difficulty firmware which was released on 25-06 - 2013?

  I've been using Google Chrome and even had 2 tabs open in the same window, one from before the update and the second I opened after the update, so this was not a factor.
  
  I had not revisited the web interface of the printer to date, and currently, I see that the problem has disappeared!
  The version of the firmware has not changed, and I did no manipulation of the printer. I also highly doubt that the main user has nothing, because it is not tech savvy. So, the problem seems to have corrected itself.

  The only thing I see now, that I did not notice before, is that there is a version of firmware fix, but it currently says 0. I don't know what it was before, but I guess zero means that there is a patch, so the firmware didn't automatically update in order to make the problem disappears.

  Problem disappeared, but I don't know how or why. I haven't decided if I will update the second printer that is the same model.

• Very strange problem with my graphics card.

  Hello, I run Vista 64-bit.

  Good evening

  I have a pavillion desktop computer with which I mainly game and go to the web with. After a year of perfection, 20 days guaranteed since the computer goes through a horrible string of accidents. He started while going through the web, then ingame, for some time I couldn't even load past my password without crashing. After a while, I could finally access my desktop without the accident and run internet as well as a few other programs.

  I thought it was over, but it wasn't my games are not running. I go into the Device Manager and see that my graphics card has a "!" sign on its side. I'm trying to update the card, no difference. I go to the Web from NVIDIA site and download the latest update, restart the computer, no difference. I'm confused on what to do now, with the recession, money becomes low, I won't be able to pay an another 9800GT came with the computer.

  I went into safe mode. It the card claims to work very well, no. "!" and everything in his property shows no problem. Outside of safe mode, the problem reappears. It's the State in the map properties:

  "Windows has stopped this device because it has reported problems. (Code 43)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  After going to the Device Manager and uninstall my video card, I restarted the computer. After reboot, I could still run at 1440 x 900. An icon poped on the right to say that he recognized and has been installing this new driver (map). After installation, I restarted the computer. Tried to start a game, but he failed.

  Then downloaded the update for the card and he ran. I restarted after that and still no change. What should I do?

  Contact the manufacturer of your computer, ask them if your model is immune to nividia graphics card number, because this has happened to many new computers with graphics card NIVIDIA so some companies like sony said they have expanded their repair for 3 years after the warranty period. If the problem is caused by the graphic driver then repair and delivery costs will be covered by the manufacturer. If you still under warranty then definitely contact them. (you should be able to do online, if you have another pc)

• Update firmware HP Proliant

  Hi guys,.

  I thought I would ask before running into trouble: I have a couple of Proliant DL 360 G4p that send alerts on our server SIM; before going to replace parts, I upgrade the firmware because it may stop alerts with newer versions.

  Is this correct use the Firmware CD to update firmware on an ESX Server? Version 8.30 has-been recently released: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 15351 & prodSeriesId = 452749 & prodNameId = 3288142 & swEnvOID = 1005 & swLang = 8 & mode = 2 & taskId = 135 & swItem = MTX-5386628436a5426199be834777

  Hello

  You can certainly use the CD Firmware update the firmware. -J' did several times and seen it "fix" reported problems in SIM as well.

  Can cross-check the i/o Compatibility Guide with the version contained in the 8.30 firmware, just to ensure that you do not get there issues.

  Good luck!