Using drive Exess?

Similar Questions

• Measure calories burned when using drive

  Hello

  The question I have is will be your Apple Watch measure speed of combustion of different calories for the same distance at the same time, when to do using workout app as opposed to not use the app to drive?

  The reason for the question is that I read by using the training app, Apple Watch switches on the relevant sensors. Does this mean that these other motion detectors are normally off and if that affect the accuracy of the measure of calories burned during exercise?

  Concerning

  Hello

  Yes - followed by an open-air market, for example, through the training app can result in a more accurate estimate of your active Calories burned during this activity.

  When follow you an activity using the application of the training session and specify a type of activity, your watch uses the most appropriate sensors and data sources to estimate the outcome of this workout.

  For example, when you save an open air market:

  • If you also take your iPhone along (with compatible Bluetooth and location Services), your watch can access the GPS of the iPhone data when estimating the PACE and distance.
  • If you do not take your iPhone along, the watch relies on data from the accelerometer in the estimate of the PACE and distance.
  • Data from the heart rate sensor is used during the estimation of the Active Calories, including calculations which are adapted to this type of activity specified.

  Calibrate your watch also helps to improve the accuracy of the different estimates made by the activity and workout app app. More information and instructions for calibration of your watch (including to reset all calibration data) are available via the link below. Estimates of the results will also depend on your personal information. To verify that this is correct - and update over time:

  • On your iPhone, in the application of the watch, go to: My Watch tab > health > edit - tap and adjust the settings, then press on in fact.

  More information:

  Calibrate your Apple Watch for better accuracy of training and activity - Apple Support

  Use the activity on your Apple Watch - Apple Support

  Use of the workout on your Apple Watch - Apple Support

• Satellite A100-784: could I use driver Nvidia on the graphics chip Intel

  Hi all

  I know that this particular laptop uses the graphic intel GMA 950. Why then were the nvidia drivers on my laptop as well during the installation of the OS (Vista Basic)?

  I visited the Toshiba website for updated drivers up-to-date, and once again, I find drivers nvidia on the download page.

  What day if I need to update the drivers graphics? Drivers Intels GMA, the nvidia drivers or both?

  Thank you

  Hello

  You're right: this laptop uses Intel 945GM graphics card.
  BUT it seems that Toshiba provides this A100 series with different graphics cards (Inel, nvidia, ati) and so the image of Vista includes 3 different drivers graphics: NVidia graphic driver, ATI and Intel graphics driver graphics driver.

  But if you want to update the graphic card driver, you have to choose only the Intel driver package

• Satellite L500-19F: can I use driver AMD Radeon Catalyst 13.1?

  On site Web AMD support for this Information on the AMD Catalyst 13.1 software suite:

  The following books are not compatible with this version:
  Toshiba laptops (please contact the laptop OEM for support of the drivers for these laptops)

  Nevertheless can use the Version?

  When the update Toshiba come from?

  Thanks for any answer!
  Chris

  > Can nevertheless use the Version?
  You can install it, but the use is at your own risk.
  To my knowledge the Toshiba drivers are changed and designed for mobile use.

  > When the update Toshiba comes?
  I noticed that Toshiba release new models of laptops very often and drivers that will come out of this new series. So in the case of the new laptop model uses the same series of ATI graphics, you can use the same driver.

• Using driver WiFi...

  I just bought a HP Pavilion 13-a010dx x 360 and formattet installed Win 7 and...

  The problem is that I can't find a driver for the wifi connection that corresponds to my BONES, I have tried the home page of Intel and Broadcom (which seems to have no specific driver), but I don't know exactly which component is in my computer. And I can't use HP support assistant without an internet connection, I can... ?

  I even tried to use my phone as connection (via bluetooth), but the computer could not find my phone either (not sure if it's even possible to connect to the internet via my phone?)

  These are two network drivers missing drivers (not sure which is the wifi):

  Network controller:

  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C & REV_01
  PCI\VEN_168C & DEV_0036 & SUBSYS_217F103C
  PCI\VEN_168C & DEV_0036 & CC_028000
  PCI\VEN_168C & DEV_0036 & CC_0280

  Ethernet Controller:

  PCI\VEN_10EC & DEV_8136 & SUBSYS_22B6103C & REV_08
  PCI\VEN_10EC & DEV_8136 & SUBSYS_22B6103C
  PCI\VEN_10EC & DEV_8136 & CC_020000
  PCI\VEN_10EC & DEV_8136 & CC_0200

  What are my options... ? Please help me...

  Thanks in advance

  Hello:

  This wireless driver should work:

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_128686_1

  This bluetooth driver should work:

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_126765_1

  Ethernet: Download and install the 3rd driver on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=14&PFID=7&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• Agilent gen 83732B signal how to use driver labview?

  Hello

  I download the driver 83732B and try to use it, whenever I open any library he always calls hp837xx_32.dll. How to solve this problem?

  Thank you

  Wee

  Did you do a search for the dll? Agilent Installer can have put somewhere a little different than when the NWLC LabVIEW (library function called node) guess what he. If such is the case, then right-click on it and select Configure. You can then go to the actual location.

• After the new installation of hard drive and a reinstall of Windows XP on I: function used Drive, Windows Update

  After the new installation of hard drive and a reinstallation of Windows XP I: Drive, Windows Update continually responds with: "Files required to use Windows Update are longer registered or installed on your computer" by clicking on the option to register or reinstall results by bike to the same error.

  Hi TedWie,

  Windows update no longer works for systems with SP2 or less. To check your systems service pack level, click on Start, run and typeWinver in the Run dialog box. If your system does not already have Windows XP SP3 installed, download and install XP SP3 from the link below. (Ignore warnings about professionals of computing and network facilities).

  Windows XP SP3.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=24

  Windows XP SP2. (According to THE level of SP)

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=28

  Note:
  If your system has a Processor AMD, download and install before installation of the SP3 of XP, theUpgrade utility Microsoft for processors not intel

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?CC=UK&LC=en&softwareitem=PV-60484-2

  If you encounter problems installing XP SP3, you can refer to the procedure described in the link below to resolve an installation failure.

  How to troubleshoot a SP3 Installation fails.

  http://support.Microsoft.com/kb/950718

  Let us know if this solves the problem.

• you backup using drive e.

  Can I save everything using the E drive?

  That's what I do.

• What formatting CD - Rs receive message "disk in use drive" in Vista

  When I try to format CD - R I get a message saying dig the drive in use, do you want to continue?

  of course, this stops it formatting I was wondering if anyone knows what it is by using the disk drive? because I really need to format these CD!

  drive in use

  http://www.vista4beginners.com/burn-CDs-DVDs

  How to burn CDs and DVDs in Windows Vista

  http://Windows.Microsoft.com/en-us/Windows-Vista/burn-a-CD-or-DVD

  Burn a CD or DVD

  http://Windows.Microsoft.com/en-us/Windows-Vista/which-CD-or-DVD-format-should-I-use

  Should which CD or DVD format I use?

  Read the above and see if that solves the problem,

  See you soon.

  Mick Murphy - Microsoft partner

• Disconnected (removed) external hard drive still exploring and using drive letter - how to remove?

  Dear community,

  I recently removed an external hard drive of my computer laptop windows 7, I guess it was not not ready to 'remove Saveli' it at that time. The hard drive itself is fine, but the icon remained in windows Explorer because it is disconnected. I manually assigned the drive letter Q on the drive before, and it always appears like that, since this disconnect. When I click on it, there is of course a mistake ("Q is not accessible. "Access denied"). When I plug the hard drive it is listed in another letter (E), the 'Phantom' to Q drive is not affected by it at all.
  It (the ghost drive) does not appear in the computer/disk management manager and I can also not reassign the letter Q on the original hard drive (or any other - is not in the list!).
  I would use the letter Q again to the hard drive (my paths and associations of are consistent) and want to get rid of the ghost car. Any ideas how?
  Thanks in advance,
  Philipp

  FYI
  It's great that the problem corrected itself, but for general reference or other who can run in the ii, how to fix a ' stuck or ghost hand "is to remove its entry in the registry key below and then open a new market or restart.  This problem is relatively rare, but sometimes and still does not resolve itself.
  (Note this drive letter Q is used by Office, click Run and sometimes mysteriously appears for this reason, unlike your situation.)

  [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\MountPoints2]

• Password reset disk wizard wants to use Drive F - I don't have an F drive

  Desktop HP Pavilion p6610f Windows 7 Home Premium 64 - bit installed Just the new hard drive and all the new updates and new programs etc.  I created the repair disk system and a full backup and wante to create a password reset disk. When I click on 'Create a password reset disk' in the control panal and I begin to follow the wizard, it asks me to put a key memory in drive F.  I don't have USB keys or disks if that's what is meant.  I was going to use a DVD - RW disc, but of course, I am unable to do so.  Why does say to create a 'DISC' in one place, and then when I go there, it says that I have to use a 'KEY' 'DRIVE F "?  If I buy a USB flash drive, which is identical to a key memory? And... I have several USB ports, none of them can be used with the USB to store data or memory?  I looked in the 'Help' section and he said just to click on "create a 'Disk' password reset. Thank you in advance for any help you can provide.

  Thank you for your time, but I already did the cover, back, vision of diagnostics and repair of disks.  I just asked why, when it is suggested that I create a 'PASSWORD' reset disk, when I start to do exactly that, the wizard tells me that I have to use a USB, 'NO' a 'DISC' and use the 'F' reader which I did not, (I don't think), I mean I know there are additional slots for disks , but I don't think I have other than those that I used to do the other ' Just discs in case where.  Just curious.  I have resigned myself to not do a. I wrote my password on a piece of paper and taped it on the underside of the top of a desk, where nobody would ever think to look.

  Taylor

• BSOD after using Driver Verifier

  Original title: pilot does not have the dump file

  Windows 7 64 - bit SP1 all updates in

  Intel i7 3770 K

  No graphics card

  ASUS P8Z77-V Pro/Thunderbolt

  Problems started with PFN_LIST_CORRUPT

  I ran the memory test several times without any problems. I ran full antivirus with MS dry Ess and AdwCleaner analysis.

  I studied the messages and articles regarding the use of driver verifier.

  When I run it, set up, restart, immediate BSOD but no file listed and no discharge minidump or generated memory.

  F8 annoys me for a secure start to reset.

  The only thing I can think to do is to select only some of the non-Microsoft drivers and keep trying to reduce it to the driver.

  Anything else I can do?

  To ensure the minidumps are enabled:
  Click Start, in the search box, type: sysdm.cpl, press ENTER.
  (In victory, 8 you can use the 'win' windows key + "s")

  On the Advanced tab, click on the Start button and recovery settings.

  Make sure that automatically restart is unchecked.

  Under the heading of the writing of debugging information, select partial memory (256 KB) image in the drop-down list (varies from 256kb).

  Ensure that the Small Dump Directory is listed as % systemroot%\Minidump.

  OK your way out.

  Reboot if changes have been made.

  If the minidumps are still not created, check these reasons as to why that may happen

  For landfills to produce what follows must be correct

  Paging file must be on the same drive as your operating system

  The basic file size must be greater than the physical RAM installed

  Windows Error Reporting (WER) system service must be set to MANUAL

  Value file system run on the operating system drive

  The value of options/crash recovery system "kernel memory dump".

  User account control must be running.

  Sometimes the SSDS with an older firmware are not DMP (firmware update)

  Applications like Ccleaner cleaner remove DMP files to avoid them until you're fixed.

  Source:

  Blue Screen of Death (BSOD) created by ZigZag3143 (MS - MVP)
  http://answers.Microsoft.com/en-us/Windows/wiki/windows_other-system/blue-screen-of-death-BSOD/1939df35-283f-4830-A4DD-e95ee5d8669d

• How to use driver ODBC Oracle

  I am a user non - I.T...  We have a database on Oracle 11 G server.  I have the interface with her using an ODBC for MS Access 2010 link under windows.  Now, I would like to work with CLOB fields, causing errors in my queries.  Some research shows that Microsoft's ODBC driver does not support these, but only to Oracle.  I.T. says they can help me to install the driver if I can find it.  This is where my confusion begins.

  ODBC Oracle drivers

  is a page on the Oracle website.  It has links to a page of drivers:

  ODBC Oracle driver download

  But this has only versions 9.x and 10.x.

  Some googling has not helped things further.  How can I work with CLOB fields in MS Access?

  I'm confused.  Using odbc to access or for the Oracle?  Make your decisions and clarify.

  The oracle drivers are based on the standard oracle client.  You download the drivers by installing the software oracle client.  For sure the customer "run time" will get it.  'Snapshot' customer can... I don't really know on the subject.

  A word of caution.  Upward to Oracle 11, the customer do not have default ODBC drivers.  You must choose to do a custom Setup when you start the installation of the client.  If you install the client of 12 c (which you should) then the odbc drivers will install by default.

  Another complexity is going to deal with 32 - bit and 64 - bit.  The oracle client and the odbc driver must be of the same architecture as the front end, which is the use.  Who'd be a 32-bit application, even if your OS is 64-bit.

  I don't know that I would trust your guy I.T. to install it if they don't know even where to get it.

• Using drive vs permanent profile

  I have the unit profile installed redirecting all kinds of things on a file server, but really what makes me?  I guess I can more easily back up this file server, then each workstation, but the others while the persistent drive seems better because it is much easier to manage.

  Any thoughts since I was in the process of establishing a new environment for our data center in Singapore?

  Thank you all.

  We use Appsense (it works well but has some quirks) and then there is RES Software.   Those are two really good companies, but also kind of expensive.   Profile Unity is one of the best bang for the buck tools, I've seen.

• using driver Wireless z570!

  Hello

  Summer get frustrated trying to fix my wireless. The card no longer works out of the blue. It seems limited, etc., while other computers in my house had no problem with the wireless. So, I uninstalled the drivers, by deleting the installation with her files. I downloaded the latest drivers and when I go to install, it fails. It is said to try to use the drivers compatible with my operating system, which I am. What can I do? I don't have any CD.

  UPDATE: I've never actually installed. I had to go to C: > drivers, then the Setup.exe. However, I'm back to my original problem. I can't connect to my router when my other one can. He told me that my internet connection is limited. I updated my BIOS to see if it would help disabled then enabled my wireless card in the BIOS. Still nothing

  Edit: I tried to release and renew my IP but I get a no. operation can be performed on the local area network connection, although it has its media disconnected error. My ethernet connection works fine. Wireless works very well with the other computer. It seems that my router is blocking my IP but I can't seem to get a new one since I can't renew

  Thank you!