Using PCI and GPIB-Enet drivers set

Similar Questions

• PCI and unknown devices drivers HP Pavilion dv7-6090es

  Hello

  After a recovery without recovery disks and the recovery partition, I could install most drivers, but I can't find, or I would say that there are some that I don't know yet.

  These are the descriptions that appear in the device as well as the hardware ID Manager

  PCI device

  PCI\VEN_10EC & DEV_5209 & SUBSYS_165A103C & REV_01
  PCI\VEN_10EC & DEV_5209 & SUBSYS_165A103C
  PCI\VEN_10EC & DEV_5209 & CC_FF0000
  PCI\VEN_10EC & DEV_5209 & CC_FF00

  Unknown device

  USB\VID_138A & PID_0018 & REV_0078
  USB\VID_138A & PID_0018

  Unknowk device

  ACPI\HPQ0004
  * HPQ0004

  Could you help me understand what devices are and where I could find the drivers for them, please?

  Thank you in advance,

  Concerning

  HP Pavilion dv7 - 6090es Windows 7 Home Premium

  Hello:

  You need these drivers...

  PCI device:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-102008-2&cc=us&DLC=en&LC=en&OS=4063&product=5085501&sw_lang=

  USB\VID_138A & PID_0018 & REV_0078:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-103013-1&cc=us&DLC=en&LC=en&OS=4063&product=5273735&sw_lang=

  ACPI\HPQ0004:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116584-1&cc=us&DLC=en&LC=en&OS=4063&product=5273735&sw_lang=

• Problem using labview and GPIB

  Hi guys,.

  Finally got recognized my tool GPIB in labview, which is nice. I created the block (attached you can see you diagram) but it works like 20 sec. I press run continious and I can change the values in direct mode, as I hear it. But then after 10 seconds, it appears the error that is in the screen and only works again if I reboot the function generator.

  The model is Tektronix AFG3102.

  Concerning

  
  

• I need communication controller simple PCI and usb controller drivers

  

  I want drivers for above two controllers

  model: 15-d103tx

  product no: G2G48PA #ACJ

  My os is windows 7 ultimate 32 bit

  Hello:

  Here are links to the drivers you need...

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5405424&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_123657_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5405424&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_128883_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

• HP8562A and NI GPIB-ENET/100

  Hi, I would like to access my Analyzer of spectrum HP8562A from my computer using the NI GPIB-ENET/100 material. Is there a screw or drivers out there ready to achieve? I searched online and on ni.com, but I can't find them. Please help me. Thanks, Rocío-

  What is available is a driver of the 8562E series

  the two machines are agilent spectrumanalyzers but you will need to decide for yourself how they are of same familytree.

  http://sine.NI.com/apps/UTF8/niid_web_display.model_page?p_model_id=2032

• With the help of two GPIB-ENET/100 boxes with ibconf - gpib1 selection?

  I hope this is the right forum for this post.

  I'm trying to use ibconf on Solaris to configure a workstation to use 2 boxes GPIB-ENET/100.  I have never tried to configure a computer to use multiple boxes GPIB-ENET/100 at the time, so I don't have a lot of confidence that I'm doing it correctly for two boxes.  Especially given what I describe below.

  According to the manual page 4-2 of the "Getting started with your GPIB-ENET/100 and NOR-488.» 2 for Solaris. "

  To identify your GPIB-ENET/100 in ibconf, perform the following steps:
  1. press on to select the option rename.
  2. type the alias name of host, host name, or IP address assigned to your
  GPIB-ENET/100 and press .
  3. press to exit, chooose to save your changes.

  I followed these steps for both boxes, but the banner at the top of the menu always says 'Card device for Council gpib0' and he always says "gpib0" just to top the host name that I go.  Shouldn't he State gpib0 first Board and gpib1 of the Committee on the second?  But I don't see a way to move to gpib1, or the unit of the second box ("Board") map.  Instead, it seems that I crushed the entrance of host name for the first box, I've identified using the steps above with the host name of the second box, that I've identified by following the steps above.

  I looked through the manual as well as fact a search online, nothing helps.  Which brings me to this forum.

  How should we do to get the pilot configured to use the GPIB-ENET/100 boxes?

  Thanks in advance.  Out of my ibconf is below (that's what it actually looks like, either incidentally - the strange on the line with dev2, dev13, and dev24 is not an artifact of copy/paste):

  ===============================================================================
  National Instruments GPIB Software Configuration utility Rev A.3.
  Copyright (c) 1991 National Instruments Corp.   All rights reserved.
  ===============================================================================

  File: / etc/gpibrc = CAPACITY: 8-plank 44 devices =
  ----------         -----------
  Press a key to continue * -.
  -----------------  -------
  ----------------  ----
  

  -------
  ----

  ===============================================================================
  National Instruments |    Card device for Council SPARCstation gpib0
  ===============================================================================
  -----------
  | GPIB0 |
  ----| nienetD |
  |   |_________|     * Use the cursor keys h, j, k, l & to select a device or a Commission.
  |                   * Use the buttons below to select the desired action.
  =====|------------------=======================================================
  | - 0 dev1 |-dev12 0 1 dev23 2 dev34
  = | - dev2 0 = = |-ev13 = 1 dev24 = 2 = dev35
  | - dev3 0 0 |---4 1 dev25 2 dev36
  | - dev4 0 1 dev15 1 dev26 2 dev37
  | - 0 dev5 1 dev16 1 dev27 2 dev38
  | - 0 dev6 1 dev17 1 dev28 2 dev39
  | - 0 dev7 1 dev18 2 dev29 2 dev40
  |---0 dev8            1 dev19           2 dev30                                                                   2 dev41
  | - 0 1 dev20 dev31 2 dev42 dev9 2 |-0 1 dev21 2 dev32 dev10
  | - 1 dev22 2 dev33 dev4311
  3 dev44
  |

  ^ Q: help ^ r: Rename ^ T: (de) connect ^ edit I: ^ o: output

  I just thought of it. My terminal has been updated with the ansi format. That was streaked the menu and blocks my view of the operating instructions ^ B / ^ F to see maps for more tips. The dockers affecting my vt100 terminal. You can even see how my menu was watered to the top at the bottom of my original message. I didn't know until now that the menu was supposed to look like different (although I knew it).

• Device ENET connect computer USB using NI GPIB-ENET/1000

  Hello

  Currently, I am trying to connect to a controller PI E-712 has an ENET port on a windows 7.

  I have a converter NI GPIB-ENET/1000 and a GPIB-USB-HS cable and want to use the ENET end for the controller and the GPIB for contact with the computer, but is it possible? Or does only for GPIB-devices of connection for calculating rusing ENET?

  I have the drivers on my computer, namely the NEITHER-488. 2, IMAX can detect the GPIB connection and the cable has a light orange on the loan. Lights green ENET-converter for power, ready and the positions of the Act/LINK but nothing either of the GPIB for speak and listen to the lamps. When trying to connect, the computer does not see the device at all.

  Any help will be greatly appreciated.

  FrellZilla wrote:

  Thank you for your adivce.

  I am sure that tha the device does support ethernet. The problem is, however, that we cannot connect the ethernet to the computer itself. We do not actually use Labview but a program called DMACS, that's why we want to use GPIB on the end of the computer.

  The NI GPIB-ENET/1000 will not work for you. It is an Ethernet to GPIB device. Your instrument is not a GPIB interface.

  I'm not familiar with DMACS.

• The card using PCI-GPIB hangs the system (Windows 7)

  Hello

  I am running Labview 11.0 (32-bit) on Windows 7 (64-bit) computer and card PCI-GPIB to communicate with instruments.

  Can I use GPIB to send commands to the device, but when I used "Measure and Automation" and analysis of the instruments he runs right first time, but if I scan again the system crashes completely (no reaction to any seizure).

  Same thing happens if I use I/O Assistant VI, I can get a response from the instrument and on the second call, the system hangs. Yet, I can send as many orders without any problem, so the source is in the reading stage.

  The PCI-GPIB card worked perfectly well for years on another computer running Windows XP.

  Someone already had this problem and what can be the source of it?

  I had a similar problem, but I just found out that the motherboard was not good...

  Try in another computer... Optionally, you can uninstall and install back the NI 488 drivers. 2...

  -Germain

• Portege S100 - reinstall Windows XP using F6 and RAID drivers

  I have this announcement in the hope that it helps someone.

  Well my hard drive is dead, so got a replacement one. I'm not so innocently, I thought that, just down load the drivers from the website of the original dvd.
  So did all of this and the raid has yet to see! Changed the settins to raid in the bios that you get by pressing ESC, then the default values, restart and go back into bios goto page 3 - which is so visible. Make sure that the disc is set to1raid0 - download the manual, but you must agree to any change in typing 1234 when it asks for a string from the manual. Anyway did all that - still no visible drive - so which continues.

  Well apparently there are 2 sets of pilots kr10n and kr10i - that givesyou site is kr10n drivers. That may work for the most recent, but not mine! My laptop needs the kr10i which I can't find on the site tosiba. BUT http://download.cnet.com/raid-drv-20070719134547-zip/3000-18492_4-174094.html or you can google for raid-drv-20070719134547

  The steps for me were so use nlite to add the drivers of kr10i on a WinXP SP3 patched cd and start using that. It was work related.

  After that, everything went great! Well, I didn't have much hair initially, but even less after having finished the process.

  Good luck

  Hello

  Thanks for posting this short statement here in the forum.
  I think it might be useful for some users who try to install Win XP and try to include the RAID drives.

  PS. driver RAID The download also from the European pilot of Toshiba page!
  I installed Win XP and I'm using the nLite tool to include the RAID driver!

• I used a time capsule in my house.  Now, I have another network put in place and would like to set my time for back ups and NOT as a WiFi capsule

  I used a time capsule in my house.  Now, I have another network put in place and would like to set my time for back ups and NOT as a WiFi capsule

  If it is possible to turn off the WiFi on the Time Capsule, which only leaves you with the option to back up your Mac (s) using a wired Ethernet cable connection between the Mac (s) and the Time Capsule.

  Are you OK with that?

• Drivers PCI and USB for W8.1 HP Compaq 8000 Elite SFF?

  Hi guys,.

  I'm trying to update an old workstation HP Elite 8000 LTS to W8.1 but can't find the right drivers for the PCI Serial Port and USB devices. Driver HP downloads page shows nothing for W8 x 64 when I put in the serial number and search for drivers. Apparently, Windows 7 is as far as I can take this machine?

  Naively, I thought that Windows can handle these aircraft out of the box, given his age.

  Can someone confirm if I'm able to run W8.1 on this material and if yes where I could find appriate drivers for it?

  

  Thank you

  Scott

  You are the very welcome, Scott.

  From what I can make of this hardware ID, it is part of the USB2 controller system.

  Something really got blocked upward with the USB/USB2 chipset driver part.

  See if this Intel chipset driver installation does nothing to correct the problem...

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=20019 & lang = eng & ProdId = 816

• HP 250 P4T79PT G3: Drivers needed HP 250 G3 peripheral PCI and PCI Simple Communications controller (Windows 7 64-bit)

  Looking for a driver for a HP 250 G3 laptop

  Device PCI and PCI Simple Communications controller drivers

  OS: Windows 7 Home Premium (64-bit)

  Impossible IM find thank you for giving the link.

  Thanks in advance

  Hello:

  When the G3 250 support site returns to the top...

  You need these drivers for devices...

  Realtek card reader driver (under the section storage drivers)

  Driver Intel Management Engine Interface (under section chipset)

• I use gmail and windows xp. How can I set up gmail as my default mail service?

  I use gmail and windows xp. How can I set up gmail as my default mail service? When I click on an online 'reply to' email address he opens outlook express which I don't use.

  How to set your default e-mail to Gmail
  http://www.ehow.com/how_5151392_set-default-email-gmail.html

• I use windows 7 and some how I set everything to open my Windows media player, I can't understand how to set it all back

  I use windows 7 and some how I set everything to open my window media player, I can't understand how to put everything back it was. can someone help me

  Take a look at these two:

  MS - http://support.microsoft.com/kb/950505/en-us

  Seven forums - http://www.sevenforums.com/tutorials/19449-default-file-type-associations-restore.html

  (Start with EXE at least).

  Good reading and see if they match your problem and, if so, if they help.

  Note: As some patches of Reg, back up your registry first use - if you can.

• Can I use arrowheads and figures to be the custom shape set come with photoshop in graphic design that will be put on Youtube?

  Can I use arrowheads and be in numbers the the custom shape set come with photoshop in graphic design that will be put on Youtube or social networking?

  Hi albert xu,.

  Greetings!

  Yes, you can as this is why photoshop is intended.

  You can use and create designs and post that publicly.

  Concerning

  Jitendra