using Weblogic JMS for delivery channel internal

Similar Questions

• How to create a delivery channel internal CUSTOM QA.

  Hello
  
  I want to use a custom for inbound delivery internal QA channel. Can someone help me please in the configuration details.

  URI cannot be something. It takes an existing location to which Oracle B2B can connect using the credentials to connect (hostname, port, number and location identifier-URI).
  In your case, it must be b2b.custom_queue

  Kind regards
  Anuj

• How to build and use a clock for triggering signal internal.

  Hi all

  Please excuse my ignorance, but I have been assigned to programming a system/operation of data collection for the experience, I'm trying and have no idea where to start. My goal is to generate a clock signal 0 - 5V with a frequency on the front panel user control and use the signal to trigger events internally. As for the output, I need to control a port analog and digital. The two channels should output a pulse of user specified width to a user specified delay each of each rising edge of the clock signal. The only difference between the two is that I need to specify the output voltage to the analog port.

  If someone could offer some guidance as to the best way to do it, would be great! Thanks in advance!

  HI C-N-O,.

  Will what equipment you use? You have access to a way out of meter? If you do, here's a hat example shows you how to generate a continuous pulse DAQmx screws Train (if you are using National Instruments hardware, otherwise you could check if there is a driver available for your device):

  Community: Generate continuous pulse Train
  https://decibel.NI.com/content/docs/doc-12164

  Alternatively, you can start by looking at the examples of DAQmx, to see some details of the analog and digital control.

  (if you have the driver already installed, you can look for them under LabVIEW--> help-> find examples-> browse-> hardware input and output-> DAQmx)

  Kind regards

  Caroline

• The use of DAQmxWriteDigitalScalarU32 for write channels share the same ports?

  Hello

  I have a USB-6509 and NOR-DAQmx installed 15.5.1. Using the ANSI c api.

  Is it possible to create several independent channels that use different lines of the same port?

  DAQmxCreateTask("",&th1)

  DAQmxCreateDOChan(th1,"Dev1/line0:4","",DAQmx_Val_ChanForAllLines)

  DAQmxStartTask (th1)

  DAQmxCreateTask("",&th2)

  DAQmxCreateDOChan(th2,"Dev1/line5:9","",DAQmx_Val_ChanForAllLines)

  DAQmxStartTask (th2)

  ....

  and repeat for the following strings:

  Dev1 / line0:4
  Dev1 / line5:9
  Dev1 / line10:14
  Dev1 / line15:19
  Dev1 / line24:28
  Dev1 / line29:33

  So I can use DAQmxWriteDigitalScalarU32 to write to each task independently?

  for example:

  DAQmxWriteDigitalScalarU32 (th1, 1, 10, 0 x 1, NULL)

  DAQmxWriteDigitalScalarU32 (th2, 1, 10, 0 x 2, NULL)

  DAQmxWriteDigitalScalarU32 (th3, 1, 10, 0 x 3, NULL)

  ...

  DAQmxWriteDigitalScalarU32 (th6, 1, 10, 0 x 6, NULL)

  These tasks will interfere with each other because they use the same port, but are assigned different lines?

  If this isn't the case, I bits to the data, if the task/channel does not start at the Px.0 line?

  Thank you!

  Yes, as long as you use the same line on different channels, they must not interfere with each other for this reason, you can create a channel by line if you wish

  The reference to using the DAQmxWriteDigitalScalarU32 function:
  "A sample of the integer unsigned 32-bit unique, wrote to a task that contains a single digital output channel. "Use this format for devices with up to 32 lines per port.

  http://zone.NI.com/reference/en-XX/help/370471AC-01/daqmxcfunc/daqmxwritedigitalscalaru32/

  So yes, the DAQmxWriteDigitalScalarU32 can write on each task independently

• How many physical connections / sessions get pooled using the JMS Wrappers

  Hello
  
  I have been reading about improved support for using WebLogic JMS with EJB and servlet and I was wondering if its possible to specify how many physical connections / sessions to a foreign JMS provider will be created? Specifically, I am using Sonic MQ are foreign provider JMS and Sonic have specified that only one connection will support up to 30 sessions before performance begins to degrade. I just want to know what means the WebLogic code "under the hood" to decide how many connections / sessions to create?
  
  Thanks for any help
  
  Mandy

  Basically, a connection is created by simultaneously active thread requesting a connection. Stats of the pool are found here on the console (if my notes are correct):

  Services-> e-mail->-> [Server JMS] JMS servers->-> Pools of connections monitoring

  It could be Session Pools and no Pools of connections.

  Tom

• How to debug a web application remotely using Weblogic Workshop 10.3?

  I am trying to debug and application using Weblogic Workshop for Weblogic 10.3 on a remote server. I added the arguments of debugging on the server in the administration console and restarted the server, but I am unable to see debugging information in the IDE of the workshop. I am probably doing wrong... How can I reach the remote debugger?
  
  
  
  Thank you!

  The argument - Xdebug you provided for the execution of the server must use 'socket', and it specifies a port number. When you create the Debug configuration of the dialog ("Remote Java Application') debugging, you must also specify 'socket', the remote host name and port number. Then you connect with it.

• Internal Server Oracle 11 g b2b JMS Configuration of the delivery channel

  Hello
  
  I'm using Oracle 11 g b2b server is configured with the Protocol of Mae. I created an internal delivery of JMS to host business partner channel. Now the message inbound (remote trading partner message) is given to dorsal application via the internal delivery of jms channel. Now, I wanted to send you this message to the domain of the weblogic another server that is hosted on another box. So where can I give the other weblogic domain details such as the message will be delivered from the host commercial b2b serveur_partenaire to the weblogic domain queue remote?
  
  Kind regards
  Belleau

  Hi Ben,

  As already mentioned by Nitesh, you can create a channel of internal delivery of JMS and even configure in your agreement for routing messages to the remote (domain) weblogic JMS queue.

  Details of port and the ip address of the remote weblogic domain can be configured as part of the JMS internal delivery, 'Provider of Destination' channel, as below,

  for example.
  Java.naming.Provider.URL=T3://:; java.naming.factory.initial = weblogic.jndi.WLInitialContextFactory; java.naming.security.principal =; java.naming.security.credentials =

  In this case, messages delivered directly to remote JMS queue.
  Concerning
  Nebot

• Waiting for WebLogic JMS - priority

  Hi all
  I am using WebLogic Server Version: 10.3.5.0 in a clustered environment.
  I use a uniform distributed queue. I investigated enqueueing a large number of messages and trying to get them to be corresponding in order of priority.
  I put the JMSPriority property successfully in messages and when I view messages in the weblogic console I see the priority.
  My composite to Dequeue uses Oracle JMS adapter and I set it up as a singleton. But I found that it treats my messages in the order they are in queue not prioritize.
  By reading the docs, I found the following: "Currently, WebLogic JMS does not honor the priority of the message." (http://www.inf.fu-berlin.de/lehre/WS00/SWT/BEA/documentation/docs51/classdocs/API_jms.html)
  This is the documentation for 5.1. WebLogic server 10.3.5.0 supports priorities and whether someone can point me in the documentation?
  Thank you
  Robert

  By default, the messages in a queue are in FIFO order, even if the messages have different priorities. So for the messages to be sorted by their priority, you must define a sort key of the destination.

  For more details, please refer to the
  http://docs.Oracle.com/CD/E17904_01/Web.1111/e13738/basic_config.htm#i1177256

• HTTP proxy for AS2 delivery channel

  Hi all
  
  During AS2 delivery channel configuration, there is a checkbox "Use proxy". Where can I specify proxy details? In addition, for the additional http headers, which is the standard that must be followed?
  
  Kind regards
  Praveen

  Hi Praveen,
  Ideally the Proxy setting is done while installation.
  If you missed during the installation and you want to use proxy B2B then you can try to give below property when you start the managed server:
  -http.proxyHost = - Dhttp.proxyPort =

  Rgds,
  Nitesh jegou

• WebLogic 10.3 not suporting for MDB to connect to remote server Weblogic JMS

  Hello
  
  I have a problem with MDB deployed on Weblogic 10.3.It's MDB simple that communicates with the Server JMS weblogic remote. I'm the exception below. could someone help how to solve this problem.
  
  < 14 April 2009 11:28:52 AM PDT > < WARNING > < EJB > < BEA-010061 > < The Message - Driven EJB: ReceiverFromDocumentum can not con
  NECT to the JMS destination: FMAContractOutboundQueue. The error was:
  [EJB:011013] The Message-Driven EJB attempted to connect to the JNDI name JMS connection factory: FMAConnectionFacto
  Ry. However, the object with the JNDI name: FMAConnectionFactory is not a JMS connection factory. NestedException message is
  : weblogic.jms.client.JMSConnectionFactory cannot be cast to javax.jms.XAConnectionFactory >
  
  -Anthony

  For example, using console on the remote WLS WLS: http://e-docs.bea.com/wls/docs103/ConsoleHelp/taskhelp/jms_modules/connection_factories/ConfigureTransactions.html

• How to use the utility disk first aid for hard drive internal el captian

  How to use the utility disk first aid for hard drive internal el captian

  Select the drive and click first aid.

  If something is not repairable because this is the system drive, then you need to start using the recovery partition and run disk utility it.

• Integrate CEP with weblogic JMS queue

  Hi guys,.

  I am trying to send data of CEP to the of Weblogic JMS queue, but I get the error message

  
  Error:

  org.springframework.beans.FatalBeanException: error initializing the context lifecycle; nested exception is java.lang.IllegalArgumentException: failed to find JNDI for jms/CEP_Q1 of the t3://10.80.4.206:7001 provider

  at com.bea.wlevs.spring.ApplicationContextLifecycle.onApplicationEvent(ApplicationContextLifecycle.java:146)

  to org.springframework.context.event.SimpleApplicationEventMulticaster$ 1.run(SimpleApplicationEventMulticaster.java:79)

  at org.springframework.core.task.SyncTaskExecutor.execute(SyncTaskExecutor.java:50)

  at org.springframework.context.event.SimpleApplicationEventMulticaster.multicastEvent(SimpleApplicationEventMulticaster.java:76)

  at org.springframework.context.support.AbstractApplicationContext.publishEvent(AbstractApplicationContext.java:274)

  at org.springframework.context.support.AbstractApplicationContext.finishRefresh(AbstractApplicationContext.java:737)

  at org.springframework.osgi.context.support.AbstractOsgiBundleApplicationContext.finishRefresh(AbstractOsgiBundleApplicationContext.java:235)

  to org.springframework.osgi.context.support.AbstractDelegatedExecutionApplicationContext$ 4.run(AbstractDelegatedExecutionApplicationContext.java:358)

  at org.springframework.osgi.util.internal.PrivilegedUtils.executeWithCustomTCCL(PrivilegedUtils.java:85)

  at org.springframework.osgi.context.support.AbstractDelegatedExecutionApplicationContext.completeRefresh(AbstractDelegatedExecutionApplicationContext.java:320)

  to org.springframework.osgi.extender.internal.dependencies.startup.DependencyWaiterApplicationContextExecutor$ CompleteRefreshTask.run (DependencyWaiterApplicationContextExecutor.java:139)

  at org.springframework.scheduling.commonj.DelegatingWork.run(DelegatingWork.java:62)

  to weblogic.work.commonj.CommonjWorkManagerImpl$ WorkWithListener.run (CommonjWorkManagerImpl.java:204)

  to weblogic.work.SelfTuningWorkManagerImpl$ WorkAdapterImpl.run (SelfTuningWorkManagerImpl.java:545)

  at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)

  <jms-adapter>
    <name>CreditCardJMSOutboundAdapter</name>
    <event-type>CreditCardEvent</event-type>
    <jndi-provider-url>t3://10.80.4.206:7001</jndi-provider-url>
    <destination-jndi-name>jms/CEP_Q1</destination-jndi-name>
    <user>admin</user>
    <password>welcome1</password>
    </jms-adapter>
  

  In the weblogic server:

  The JMS adapter resources outgoing connection JNDI adapter: eis/queue / CEP

  ConnectionFactoryLocation: jms/OCEP_CF

  Connection factory JNDI name: jms/OCEP_CF

  JNDI queue name: jms/CEP_Q1

  
  

  Advice me please.

  
  

  Thank you

  Yatan
  

  Hi guys, this solved, the problem was that I was using the wrong port of JNDI, my queue was targeting the soa-server1 on 8001.  correct is t3://10.80.4.206:8001

• Domestic delivery channel in 11g

  Hi gurus,
  Can anyone suggest the creation of a domestic delivery channel in Oracle 11 g.
  My scénarion is to send a file on the local computer using file system remote trading partner.
  
  Concerning
  REDA

  Hi reda,.

  is this two are identical or different.

  11 g, internal channels (for documents receipt of the main applications to send remote TP) is created in the host TP--> channels tab and they are marked as internal. If you want to set up a delivery for the host channel partner sales (for the receipt of documents from TP remote), then configure it in administration--> listening channels tab and make sure that it is not marked as internal. In addition, listening to the channels do not participate to an agreement.

  We must send an ASn to them by way of delivering inside using the protocols file

  You are unable to send message to a remote TP using internal delivery channel. IDC used to receive/send messages from/to final applications.

  In case you have any confusion, remember.

  Kind regards
  Anuj

• WebLogic JMS queue - delayed Messages

  Hi all
  I am using WebLogic Server Version: 10.3.5.0 in a clustered environment.
  I use a uniform distributed queue. I investigated rate messages with a delivery so that they don't not be removed immediately and instead will wait until a specific time before their delivery. In the weblogic console, I see a field delivery time, but on all my posts, the value is (no value specified).
  I use BPEL and the JMS adapter to the queue of messages. Anyone know how I can configure this property to delay the messages?
  Thank you
  Robert

  I know that SOA JMS adapter has added new features to exploit features value-added WLS JMS in recent versions, but I don't think that the delivery time is in the plan.
  Your best bet would be to set the time to deliver on the factory of connections or the destination.

• using weblogic unit-of-order (PUA) in the osb proxy service

  Hello
  
  I have a deployed on Weblogic server JMS queue. The messages in the queue are grouped using Weblogic JMS_BEA_Unit-of-order (PUA).
  
  Now, I have an OSB 10 g of Proxy Service that reads messages from the queue. The problem is, upon receipt of a message, acknowledgement of receipt is sent immediately, thus eliminating the message from the queue and the next with the same unit-Of-Order message is ready for processing.
  
  But the business scenario is the first message to read, processed and then decide to recognise or not. The second message should not be interpreted, unless the previous message is processed successfully.
  
  Can someone help with this scenario?
  
  Thank you
  Alex
  
  Published by: user9024636 on February 11, 2010 02:57

  with PUA, you'll need to do the syschronous transaction.
  1. make transacation enable XA
  2 using the road for the sychrounous transaction
  3. use the routing options, and then select mode = request-respone
  4. If the Proxy service is based on the jms then you should also together WHAT JMS Transport-> Advance settings-> XA is required-> checked

  Kind regards
  http://SOA-Street.blogspot.com