VCS CPL block call between subareas

Similar Questions

• Restricting calls between a subarea and specific extensions on Cisco VCS

  Hello, I use Cisco VCS 8.5.3, my goal is to restrict calls between a subarea and specific extensions.
  I tried following solutions:

  1. Download of XML strategy
  2. Use of political appeal web interface in order to limit calls

  XML file:

  
   
   

  
   
     
     

  
     
     

  
     
     

  
       
     

  
     
   

  
  
  

  But when I apply the XML file, or try using the web simple rule (for example: 11111 12222 destination source, dismiss the action) I'm still able to place the call to 11111 to 12222.

  What can be the cause of the problem and what else can I try to be able to prohibit calls between a particular Subzone and exentions?

  Attached, is an example of CPL script that should work.  Using this script, CPL, I was able to block calls to a subarea set to a destination alias located in the subzone of default and was always able to call any other end point in the default subfield without problem.  Note that you must enter the name of the subarea, as you have configured on the VCS, including spaces if they exist.

  The scenario is based on the example of CPL "limiting access to a local gateway" X8.5 VCS Administrator's Guide on pg 413, other documents of CPL reference and examples can be seen starting on pg 410.

• Limit the number of calls between areas of VCS/subareas?

  Hello

  I wonder if there is a way that we can limit the number of calls between two subareas, areas or VCS.

  The script as below:

  VCS-E (owncompany) < -----neighbor/traversal/dns="" zone="" over="" internet------=""> > VCS-E (partner)

  My intention is to limit to 5 video calls from VCS-E (partner) so that the 6th call (dial in endpoint) will be blocked.

  I know that we can control the total bandwidth between areas using links & pipes but that does not stop the remote end to lower their rate of recall and deal with several endpoints.

  Thank you.

  Hi Hafiz,

  have you tried to disable the 'downspeed by mode of appeal"in a configuration of Bandwidth?

  try disabling the "downspeed" by call OFF mode under VCS config-. > bandwidth--> configuration.

  This will not allow the calls get the downspeed but it must block because of insufficient bandwidth.

  Thank you

  Alok

• VCS - CPL to block call routing to and from the same area of neighbor

  Hi all

  Is there a CPL rule that can be written to block calls from a neighbouring area to the same area of neighbor?

  We have problems with CUCM sent appeals to the our VCS VCS then routes the call return CUCM, causing thus "too many jumps."

  In the example

  MOVI user control VCS try to compose endpoint registered RTC CUCM, but incorrectly dials

  Appeal does not have to search for the terms of local area

  Call does not match search for VCS Expressway rules

  Call corresponds to captures all of CUCM (. *) @domain.com

  CUCM does not form DN or URI for the wrong phone number and the call is routed to the VCS control due to the SIP routing model of *. * on CUCM

  We have to capture all CUCM at the end, since we offer PSTN, as well as our users and phones have the alphanumeric URIs assigned to the DNs for Jabber, etc.

  I fear that he is not really an easy way to do it, I know because the call charged CPL first, CPL don't know what area it was intended for.

  It's probably more easily accomomplished with a slight modification to your rules of research rather than spraying anthing "@domaine" everywhere - something like:

  Anything incoming directly at @domaine in the nearby area of the local area (as is inside your organization, such as if the CUCM not found and sent it to the VCS he won't be on the CUCM, so must be local (or nonexistent) - and stop.

  And the opposite of the above - route whatever it is for @domaine of the localZone.GetDaylightChanges (because it was not found locally) to stop and the CUCM neighbour-

  And do similar for what is coming from other areas outside to route to wheverver that will be endpoints.  In this way, your call should not be bouncing back between the CUCM and VCS and create the loop that you are currently experiencing.

  Of course, if your environmetn is a little more complex than the simple CUCM and VCSes, this can be a bit oversimiplified, but could lead you in the right direction.

  Another thing to consider too - if you put in your endpoints in a directory, users can use - that will help you to prevent wrong type stuff :)

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• I can't make call between Tandberg C60 using the Sip Protocol

  Hello

  I tried to call between Tandberg C60 codecs with the SIP ends, unfortunately the call failed to connect. His poster is not the message "connecting" either.

  Then I changed in the Codec c60 (both sides c60) H323 Protocol, then call connects and works well.

  Please any idea.

  Thank you.

  Kind regards

  Henri El Salvador

  ==========

  VCS ver: X7.2.1

  TANDBERG Codec C60;

  Codec1: TC4.2.4.296355

  Codec2:TC4.2.4.296355

  You can't just dial the SIP with an IP address only - that is not a valid format of SIP.  There must be a [email protected] / * / or [email protected] / * / (IE [email protected]/ * /) format.

  In your example above, you should be able to dial '[email protected]/ * / "or"[email protected]/ * / "-these two are valid SIP addresses.  The right 10.88.17.5 the IP address is not.

  PS - As mentioned by Patrick, you really should upgrade your software on your endpoints to a newer version.  There is a security notice that should help you get the new software, even without an active service contract: http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20140605-openssl

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Is it possible to block calls "Unknown Caller"?

  Is it possible to block calls "Unknown Caller"?

  I know how to block calls from numbers that are unrecognized, but when no phone number is detected, it doesn't seem to be a way to block these calls. (When you click on the "I" (information) in the histoet call, no option "call block" does exist.

  It is not possible on the phone, but contact your wireless carrier. Some offer this choice to their end, until the calls are even connected to your phone.

• What happens when a number of blocked calls a person and they're on another line?

  What happens when a number of blocked calls the person and they're on another line? Does go directly to voicemail, or ring several times to voice mail?

  If "on the other line" means on another call and call waiting is activated, the blocked call goes straight to voicemail.

• Impossible to block calling in FaceTime

  With the help of v10.11.2 El Capitan

  I need to block a caller in FaceTime.

  I missed the call (from 0843 980 0142) and check found this to be a jerk.

  When I click on the 'i' to the right of the number in the call list, I add to my address book. The "block" option provided for help to FaceTime is missing.

  If I useFaceTime / preferences / block then it gives me once again that my address book as a source. I can't add anything else.

  Of course, I want more in my address book.

  Read here: FaceTime for Mac (Yosemite): block calls

• How to connect 2 PC with CPL blocks on windows?

  How to connect 2 PC with CPL blocks on windows?

  original title: CPL problem
  Hello
  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:
  http://support.Microsoft.com/common/international.aspx

• How to block call someones on z3 compact

  How to block call someones on z3 compact

  You can't actually block. There is an option to send calls directly to voicemail, but to block you cannot without a 3rd party app.

• Smartphones blackBerry how to block calls or I cant.

  need to know how to block calls

  Hi theunderdogg1965

  Welcome to the community

  If you want to block some calls on your device, you can install any App.Go to App World of call blocking, and there are several version free call blocking app available. It allows to block these calls.

  Prince

  Click 'Like' If you want to thank someone.

  If problem resolves mark message (s) as a 'Solution', so that others can use.

• BlackBerry Smartphones block calls?

  Is there a way to block calls from a number on the 8320?

  Download iblocker lite in the app store. It's free.

• Cannot connect call between two SX20

  Hello world

  I've implemented two Cisco SX20 units at two sites. When you attempt to place the call between two units, it is unstable. In particular, sometimes the call is connected, sometimes, it is not connected even if ping, tracert are Ok. It's very strange. I'm sure that the SX20 unit works well. If I make a conclusion that there is a problem with my network but I don't exactly know why.

  All the world is facing this problem before?

  Dzung.

  Hey yours,

  Disable NAT if you do not use.

  Also useful to configure QoS, check on your link packet loss and bandwidth.

• Call between 3200 TP and question TP 1300-65

  Hello

  question of pls, an active call between 3200 TP-TP 1300-65, which is the normal behavior of the output display perspective TP3200 or 3 screens? (showing the room TP 1300-65) He must have the intermediate screen active and left and right are idle black?

  Not having does not have access to one, I am unable to test, but yes, I would say that the TX-1300 (being only a single display system) only appear on the single (in the middle) screen of the CTS-3200 and the other two would remain empty (or display other connected parts).

• Block calls with the Expressway CPL script custom field empty

  We currently have a CPL script in place on our highway E we use to restrict access to certain devices.  We found that we had a call from h323 come in which the field is empty, it is somehow making it through scripting and is able to call anything.  Here are our current config:

  -

  -

  -

  -

  http://www.w3.org/2001/XMLSchema-instance"xmlns:taa ="http://www.tandberg.net/cpl-extensions">."

  
  

  
  

  -

  -

  -

  We tried to change the rules where the origin is empty, or just simply have a *, but it doesn't seem to work.  Anyone have ideas on how to match a call when the field is empty?

  Thanks in advance!

  I get the these calls all the time. the CPL script that I use to block is attached.

  Question of the use of the good source and destination, for example in the attached CPL, I use: