View installation agent causes slow connections at the office (office preparation phase)

Similar Questions

• My cloud of Adobe installer is unable to connect to the animated. No problems with internet... Help, please

  My cloud of Adobe installer is unable to connect to the animated. No problems with internet... Help, please

  Hello

  Thank you for using https://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html > and all the steps in "troubleshooting connectivity issues.

  If necessary, and for any other question, click on through http://helpx.adobe.com/contact.html and so "open" Please use the chat, I to can I part had the best experiences. An employee of Adobe Preran I quote: the chat button is enabled as soon as there is an available to help agent.

  Hans-Günter

• I tried a lot of time to download Lightroom on my MacBookPro without success. I already remove the firewall. Perhaps because of a slow connection to the Lebanon? Or another problem?

  I tried a lot of time to download Lightroom on my MacBookPro without success. I already remove the firewall. Perhaps because of a slow connection to the Lebanon? Or another problem?

  Beatricel88978029 you receive specific when errors download Photoshop Lightroom?  For more information on how to resolve errors download please see error download and installation of the creative cloud application.

• recently, I intend to download, but unfortunately this is already more than 5 attempts. Thanks to the slow connection and the power outage, my download has failed to complete. Would it not possible to download the app again? Concerning

  Recently I wanted to download, but unfortunately it's already more

  only 5 attempts. Thanks to the slow connection and the power outage, my

  to complete the failed download.

  Would it not possible to download the app again?

  Concerning

  A trial version is not different from the full version.  Using your serial number to activate a trial version, the access limit is removed.

  If you get access errors thrown at you when you try to use a download link, check that you have enabled cookies and clear your cookie cache.  If he continues to not try to use a different browser.

• Slow connections to the internet wireless

  I have problems with my wireless with my brand new Dell laptop running Vista 32 bit.  I spent a lot of time to read about it online but have not been able to solve my problem.  Here are my steps, I took so far

  D/led drivers Dell Wireless
  -J' uninstalled McAfee Security Center
  -disabled autotuning, rss, tcp/ip v6
  -Flashed the firmware newest on the router (netgear WGR614 v5)
  -set levels of power for maximum performance on battery

  Wired product than the internet very fast speeds so it's a wireless issue.  My other laptop running XP THAT works well on wireless so I think it must be related to Vista SP2(even ran the same virus scan programs on both computers).  Some pages load more quickly, but as soon as I'm lulled into a false sense of security on the internet speed, I get hit with a page very slow loading Web or the connection is lost (although I am still connected to my wireless network).

  Any suggestions?  This has been a very frustrating and aggravating, issue especially with a brand new computer.

  Thank you.

  Hello

  You can check your connection Wireless at a library or other WiFi spot just to rule out any problem between
  your router and the new system. Have you tried to assign security to WPA and make sure that you broadcast
  SSID that some routers and systems have problems. If disable you (OFF) the system XP is there a difference in the way
  the new system works with the WiFi connection?

  Security/antivirus/antispyware products could also play a role here, even if the same as those on XP seem to
  work well. Were there more of them on this system even if you have uninstalled them when they leave often remains
  which may cause strange problems.

  =========================================

  Try these to erase corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  --------------------

  Departure - in the search box, type-> order

  at the top of the list to find COMMAND - CLICK RIGHT to it - RUN AS ADMIN

  Type the following commands (or copy and paste one at a time), each followed by pressing on enter.

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  RESET

  That resets your TCP/IP stack
  =============================================

  How you are positioned in the router? Are there obstacles in the path?

  Try actually updated your driver on the site of the manufacturer of the device if possible, and by disabling the network logon.

  It's the generic drivers up to date, and you did the part at Dell.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  ===================================

  You should check with Dell since this is a new system and insist he work correctly (especially after having tried it on other
  WiFi connects if the problem is constant). Also, check Dell spirit and their forums, because it might be a known issue.

  Dell support
  http://support.Dell.com/

  Dell forums
  http://en.community.Dell.com/forums/
  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Very slow connection to the LAN on my Tecra M1

  Hi all

  I use a Toshiba Tecra M1 1 .6GHz, Win XP.

  I found that there is a problem with the connection to the local network. It is very slow. I takes about 5 minutes to download 1 MB. It's really a lot of time if I want to download and update some software over the internet.

  I also have an office. It is quite a bit old but the connection to the local network is much faster than my laptop; for example, I downloaded Windows Mediaplayer 10 - about 12 MB by using desktop and laptop at the same time to compare, the Office has taken 2-3 minutes while the laptop ate more than 20 minutes. I switched the cable between the office and cell phones, but it did not help.

  We know the problem and the solution?

  Much thanks.

  Hello

  Nick is on the right track. Who knows what runs in the background and applications who wants to access the internet. I recommend you to use the tool called Zone alarm. On this way, you will have full control over the applications that want to access the internet.

• Slow connection with the built in WiFi card

  I have a connection wanadoo adsl internet 20 Mbit family with a direct box. The box is also a wireless router.
  When I connect to the livebox with my toshiba mx40-231, the connection is very slow. The connection is constantly switch between 1 Mbps and 54 Mbps and speeds range between. It is also the problem. One moment an internet page is send in 1/10 of a second and 1 minute later a page to load in 20 secconds! the strang thing is that the intensity of the signal is constant high!

  With the direct box, I also had a wireless USB key. When I use this stick I get a connection very quickly 54 Mbps constant.

  It seems to me that the construction of the wireless card is the problem. I already have the latest wireless driver and tried a few channels on the router.

  Someone at - it an idea to solve this problem so I can throw this wireless stick :-) Thing very clumpsy this stich on such a portable wireless of beautifull!

  Hello

  If you check the wireless card, you will find many topics on this subject. We know that Intel 2200 B/G card wireless make disorders and connection is not constant. We can only speculate why this happens, but the fact is that this card has problems with different routers.

  For example: Satellite M40 has the same card and the fantastic work with Netgear router. Even with Belkin, it works well in full speed.

  I recommend you to install the latest version of the driver Intel

  Good luck

• Very slow connection on the WRT610N

  I bought a brand new WRT610N recently but didn't experience any improvement in speed, therefore began to study a little.

  I have a broadband cable, 30 Mbps connection.

  Cable modem is connected to a network adapter.

  An another output-power adapter is connected to the WRT610N

  now, when I connect my laptop through the router (wired or wireless makes no difference), my (upc speedtest) speed is about 5 Mbps.

  When I connect to the internet via cable to uplink on the router, I have 12 Mbps.

  When I connect directly to the cable modem, I have 28 Mbps.

  So, a big loss is caused by food taken thingies, I can get more quickly those who or stop using them at all. But what causes the loss of the router? All I can do about it? It shouldn't give me easily the 12 Mbit/s, it becomes itself?

  Any help appreciated.

  If connect you your computer to the WRT610N, you should be able to get on the same 28 Mbps you get from your cable modem.  Since you get only 5 to 12 Mbps wired, this suggests that there is probably a problem of basic configuration.

  (1) have updated the firmware on the router?  If so, after the update of the firmware, you reset the default router, and then configure the router again from scratch?  If you do not reset the router by default since the last update of the firmware, then please do it now and see if it solves your problem.  If you have saved a file of configuration of the router, DO NOT use it - you must configure the router again from scratch.  See "Reset to Factory Defaults" below.

  (2) using peer-to-peer (P2P) software?  If so, it is a known cause of slowdowns of router and disconnections.  The problem can occur even if you are not currently running the P2P software.  Stop using the P2P software.  It may take up to 5 days for your router erase from his memory.

  If the above does not solve your router, then proceed as follows:

  (3) Please indicate your ISP

  (4) Please indicate the make and exact model of your modem (not the WRT610N) number.

  (5) Please do the following test:

  Put your entire network.  Using an ethernet cable, connect your modem directly to your computer.  (Do not use the WRT610N for this test).  Turn on the modem and the computer.  Make sure you have an active Internet connection, then go ahead with what follows: (even if your Internet connection does not work, include this and move forward.)

  Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig/all" (with no quotes), and press the Enter key.   Copy all results in your next post.  To make the copy, highlight the results, and then use the keys copy (Ctrl-c) and paste (Ctrl-v) keys.  If your "IP address" does not begin with 192.168, then for security reasons, delete the latter half of your IP address.

  Reset to factory settings *.

  To reset your router by default, follow these steps:

  (1) turn off all computers, the router and the modem and disconnect from the wall.
  (2) disconnect all the wires of the router.
  (3) turn on the router and let it start up completely (1-2 minutes).
  (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
  (5) turn the router.
  (6) connect a computer cable to port 1 of the router (NOT to the internet port).
  (7) turn on the router and let it start up completely (1-2 minutes).
  (8) the power of the computer (if the computer has a wireless card, make sure it's off).
  (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
  (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Exit your browser.

  If you get this day without problem, try the Setup disk (or configure the router manually, if you prefer) and see if you can get your work and router configuration.

  If you can not ' response to... ". "in step 9 above, your router is probably dead. A report with this problem

  If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. Related to this issue.

  If you need additional help, please give the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.

  Please let me know how things turn out for you.

• I need some help please (Horizon View Client can) do not connect to the server of connection, invalid key license server connection

  Dear professionals

  I am trying to connect to connect to the server via the Client view Horizon but when I enter the IP of the server connection I got the error message indicating that

  connection to the server was not a valid license key (see attached photo)

  everything has been installed and configured correctly, I added the vcenter Server view Portal administrator and I also added new swimming pool inside

  See administrator portal, but I don't have the login server license key.

  should I really buy the connection to the license key server? is there any version of the elevation of the connection to the server?

  Please help me

  Thank you

  naoufl

  Yes you need a license key to use the view of the Horizon, there is a 60-day evaluation license if you register here:

  Try VMware view Horizon: Access virtual office

• Connection to the Server VMware View farm doesn't not connections to the foreign gateway server?

  We know a pernicious problem between our

  External security gateway and our internal view connection server.  (I have the terminology right?)

  After a few days of running normally, users trying to get

  to connect to the gateway of external security using the VMware View Client will not

  Download the logon panel.  He invites you to their

  the server must connect, but won't the login Panel and the user

  Finally will get a time-out error.

  Experiments have shown that the only way to solve this problem is

  in the reboot / restart the Server VMware View internal connection.

  Meanwhile, internal users can use VMware view

  Client to connect to the internal server without problems, don't ask that of the

  external server have problems.

  Review the journal on the external sever I hear.

  Information, '102', ' 25/04/2010.

  "21: 55:20", "VMware View", "9", "NT".

  "Connection test AUTHORITY\SYSTEM","(Request1224) AJP failed:"

  com VMware.VDI.ob.tunnelservice.CX: unable to write data to the server: java.net.SocketException:

  "Connection reset by peer: socket write error."

  And then this message is repeated.

  Warning, "104", "26/04/2010.

  ' 09: 08:04 ","VMware View","9","NT ".

  AUTHORITY\SYSTEM"," (Request1236) request failed: "

  com VMware.VDI.ob.tunnelservice.CX: cannot read the server: java.net.SocketException:

  Reset connection. "

  Examine the dumps of the internal server, I see a lot

  connections listed in the external security gateway which in my opinion should not

  exist yet because there are no active sessions.

  TCP 10.1.1.67:8009 123.456.789.123:1274 ESTABLISHED

  TCP 10.1.1.67:8009 123.456.789.123:1294 ESTABLISHED

  TCP 10.1.1.67:8009 123.456.789.123:1300 ESTABLISHED

  TCP 10.1.1.67:8009 123.456.789.123:1311 ESTABLISHED

  TCP 10.1.1.67:8009 123.456.789.123:1312 ESTABLISHED

  .

  .

  .

  Both servers run the 4.0.1 level.

  Someone at - it advice?

  Thank you

  .. .pjpg

  I had something similar happen a year where every two days I have to restart internal broker for connections that was paired to the Security server.   We have opened a ticket with VMware support, and it took a good 5 months to get the issue developed and the solution ended up being to change a value of timeout on the file server.xml on the broker for connections.   I don't know if it's the same problem that you encounter, but if you already have a ticket open with VMware you can refer to our old 1147071161 SR and may save you time.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Win 7 cannot find the driver on the laptop to HP Deskjet 5600 connected to the office via WLAN

  I have HP Deskjet 5650 color printer connected to desktop Dell Dimension 2400 under Windows XP Home Edition Ver 2002 SP3. I just bought a laptop Dell Inspiron N4110 running Windows 7 Home Premium SP1 64 bit.

  I am trying to connect to the printer via my home WIFI network running through a Netgear Wireless-N 150 WNR1000 router.

  When I add a printer on the laptop, it shows on the list of printers available on the select a printer screen, but when he tries to connect, it returns with a message, "cannot find a driver for HP Deskjet 5600 series on the network.

  I tried to locate the driver manually, but without success. I have an older HP laptop that is running Windows XP, which has always connected to the printer via the WIFI network very well.

  Can I connect the printer directly to the new laptop via a USB port and it recognizes, installs and runs very well.

  But I need accessible and connected permanently to the desktop from the laptop when it is connected to the WLAN.

  Can someone tell me how I can get my new laptop to locate driver files on when connecting via the WIFI network, please?

  Thanks for your help!

  Very well!!  He finally got!

  had to go to the properties of the computor, advanced system properties, system, device installation settings and game to install drivers from windows update if it is not found on my computer.

  Then, it would finally be search on windows update for drivers, but would not yet find a driver even from windows update to the printer when installing it as a network printer.

  I had to add a printer as a local printer, and then select Create a new port, local port, and the port name, I had to enter the path through the network computer to the printer (as "\\desktopname\printername").

  Then and only then, did that pick me from a list of printers, and we found a driver on windows update.

  Yet once again, I appreciate your help! Looks like we may have learned something from this experience.

• I am unable to get ios mobile to connect to the Office Server, what can I do?

  The number of the server is the same on mobile than on approx. desktop Mobile application gives an error message stating cannot download archive server. What can I do to fix this?

  I assume you mean the developer app PhoneGap and the desktop PhoneGap app?

  If so:

  • Your device must be connected to the same network as your development computer.
  • Make sure that the versions of the PGDevApp and PGDesktopApp are up to date.
  • Try with a freshly created project - if it works, something can be upward with your particular project.
  • Add ports that pgdesktopapp uses to your firewall settings so that data can flow freely. You can temporarily disable your firewall to see if that's the problem.
  • You may need to add an exception to your antivirus software. Again, you can temporarily disable the AV to see if it is causing your problem.

• Slow connection to the view field Pool Win 7 Desktop VMs Desktop after the installation of Microsoft Securty Essentials

  Hi, we have an environment VMware View 5 with Windows 7 Fund pools built (near 30 virtual machines). The VMS connection time is fine until I recompose for Microsoft Security Essentials - almost 40 sec, max 01 min.

  But after I install Microsoft Security Essentials on the basis of gold and recompose the linked clone desktops, the connection time is degraded on office pools because it takes almost 03-04 mins for just the domain user name. I tried this a few times and it's always the same result. Each Desktop VM have 02 GB memory assigned & we have RAM sufficient on the hosts as well.

  Any ideas? It's just temporary & interim solution until we get the McAfee solution MOVE in place as an AV is important for desktop computers because they are not destroyed log off & still exist.

  Waiting for the useful suggestions or the idea. Thanks in advance for the help.

  Welcome to the forums.  Are you by chance using Persona?    There is a KB that describes a downturn when scanning files of persona.

  http://KB.VMware.com/kb/2011823

• Re: Installation Canon IXUS V - connection of the camera not detected

  I installed the driver from the website of Canon, but when I connect the camera, I get a message saying "connection Camera not detected' followed by an error message saying pscN109 has stopped working.

  Then a message from Microsoft saying no soloution found. Can someone help me?

  Hey Buddy

  May I ask why you post this message here on the forum of Toshiba?

  I think you should contact the manufacturer of the device for support

• Slow connection to the mapped network drive

  Here's my situation.

  We have 10 workstations, all on the same, all computers running windows 8.

  We have 1 router, 1 switch and a SIN.

  9 computers can access our NAS with ease via the network of navigation or the mapped network drives.  The 10th computer cannot even open the network folder, or the network mapped drives when they appear she clicks 'This PC' falling down.  In fact, the PC 'that' fall down, never actually opens.  The green bar loads the top of the page, but never actually opens.  The network folder, does not yet appear.

  She is able to ping the NAS very well (as well as other machines) and that it can access the NAS by opening a program (word or excel for example) and then opening a folder and navigation, but it is obviously very embarrassing.

  What gives?

  Why can she access the NAS in a program like Word or Excel, but not of navigation?

  Hi George,.

  Thanks for posting your query in Microsoft Community Forum.

  According to the description of the issue, I recommend you post your query in the TechNet Forums. TechNet is watched by other computing professionals who would be more likely to help you.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=W8

  Hope this information is useful.