VIsa error code: 1073807195

Similar Questions

• VISA-1073807343 error code when using ResourceManager.GetLocalManager (). FindResources (filter) to detect the map of Pickering PXI

  I'm upgrading our test system for Windows 7 and NI Developer Suite 2012 DS2 in Windows XP and NI Developer Suite 2008 4th quarter. I have a problem with the help of VISA to detect devices PXI of Pickering. The problem occurs with the next .NET NationalInstruments.VisaNS.ResourceManager.GetLocalManager () call. FindResources (filter). I use the filter "PXI? * INSTR.

  To trouble shoot this problem I was using the VISA program FindResources.2008 c# example. I get the following error message when you apply the "PXI? * INSTR"filter. "Where not enough information or the device or resource is not present in the system. VISA-1073807343 (0xBFFF0011), ErrorResourceNotFound error code.

  Looking at other markets, I infer that VISA is not find the maps. I came across the same error message when I tried to launch the "GPIB? * INSTR"filter however I determined that there was a problem with the NOR-488 driver. 2. after having repaired the driver of the FindResources.2008 program would find the GPIB instruments using the "GPIB? * INSTR"filter.

  Max the Pickering cards appear in "Devices and Interfaces" and are listed as follows:
  12: PCI Device 'PXI12::9:INSTR '.
  15: PCI Device 'PXI13::13:INSTR '.

  In XP, the cards have been identified as:
  PXI12::9:InStr (Pickering 40-785-522)
  PXI13::13:InStr (Pickering 40-780-522)

  Also Max for each device, I am able to open the Panel to Test VISA.

  Any ideas why the VISA is not able to detect these cards?

  Thank you

  I thought about it. Apparently I needed Windows 7 to install the driver for cards of Pickering. I guess the "PXI VPP / VISA drivers" supplied by Pickering Test would take care of this.

  Until Windows has installed the driver of Pickering cards have been listed as a PCI device under 'other devices '. After installation, the cards have been listed under "devices PXI of NI-VISA.

  MAX the card now are listed as:

  12: Pickering 40-785-522 'PXI12::9:INSTR '.
  15: Pickering 40-780-522 'PXI13::13:INSTR '.

• VISA IC returns the 0xBFFF003A error code when reading the USBTMC device

  Hello

  I'm creating a USBTMC device and have some difficulty to determine why a viRead returns the 0xBFFF003A error code. Strangely enough, it reports also to read the correct byte number and the buffer contains the correct data. I use VISA IC 5.1.2 but I had the same problem with version 5.0.3. I have no problem with the device recognized by VISA IC, MAX, LabVIEW SignalExpress or LabVIEW. Using the previous version of VISA IC performing an async read would return a code completion, 0x3FFF009B (VI_SUCCESS_SYNC).

  The attachment of the utility Trace all communications from e/s or watch for when the USB cable is plugged into the computer.

  Lines 1-18 LabVIEW SignalExpress 2011 has begun

  Lines 19-35 VISA IC: open the selection

  Line 36 VISA IC: claire

  Line 37 VISA IC: Read - 10 characters

  Line 38 VISA IC: Read - 21 characters

  Lines 39-44 LabVIEW: open, read 21 characters

  Line 45 VISA IC: Read - 18 characters

  Line 46 VISA IC: claire

  Line 47 VISA IC: Read - 18 characters

  Line 48 VISA IC: closed

  Note: LabVIEW crashed on line 44.  At the moment I know not whether that is related to this problem or not.

  Full error description: failed to start the read operation because the installer is not valid (because of attributes defined in an inconsistent state).

  I'm confused by why it says it cannot start operation when in fact, it returns the requested data and attributes that it refers to? I reviewed the USB descriptor values that I use, and they look correct to me.

  Any ideas?

  Thank you

  Hi Perry,

  I found the problem.  The TransferSize didn't get converted from big-endian to little endian and 0x0A was considered 0xA000000.

  See you soon,.

  Airaki

• error code 5507

  error code 5507

  Hi arsenal2014,

  Please visit Apple support communities.

  If you receive this error when you use home sharing, don't forget to try the troubleshooting steps to help with home sharing.

  All the best.

• I can't drag and drop files in the trash, error code-43 is detected, what should I do?

  I can't drag and drop files in the trash, error code-43 is detected, what should I do? What is an error code - 43?

  You can't empty the trash or move a file to the trash

  If the above does not help, then see below:

  Visit The FAQ XLab and read the FAQ on the waste problems. You can also try using Trash it! 5.1 to solve the problem. Or you can try this:

  Open the Terminal in the Utilities folder, and paste the following at the command prompt:

  sudo rm - Rf ~ /. Trash

  Press RETURN. Enter your administrator password when prompted. It will not echo to screen. Press RETURN again.

  (Someone should tell you that it is dangerous or useless, please disregard the comment.)

• Error code 23 Bulletin Board.

  Hello

  I've problem with display error code compare 23 and doesn't work. When I press right button display error! I can't use the feature on this feature, it is locked.

  Who can help me? Please, I beg you!

  Thank you very much!

  Hey Buddy,

  It seems that something has confused your display software and if you get an error code and it s not in use.

  Simple reinstallation of the program should help get rid me of this. Simply visit the Web from Toshiba site and looking for the latest version. Download and install it then your bulletin board software should work again as usual. :)

• HP Deskjet 3056 A does not: 0xc7390500 HW_BARACUS_HEA error code

  HP Deskjet 3056 A windows 7 64-bit wireless configuration

  Do not answer and this displays on his screen.

  0xc7390500 HW_BARACUS_HEA error code

  I bought this black and finally installation Friday in our new apartment. Settled and a test page printed, all very well, even a sodoku puzzle. Really impressed me here.  Left work in the other room, later my fiance has continued to visit him, and this mistake was on his screen. for the past 2 weeks I did my best to figure out how to solve.  All programs support and stuff do not help, says they can not connect to the printer. Hooking up to usb allows it to be recognized but do not operate.  Unplug / vile the power button and it will boot fine, and after a second idea, it appears.

  I don't want to whimp out and return immediately. but my patience has been tested...

  These codes 0 x normally indicate an internal hardware error state in the printer.  The software of the printer is not link to the printer correctly, right now, is because the printer is in an error state.

  There is a document to solve the codes of x 0 in printer Deskjet 3056 has found here.

  I hope this helps.

• GPIB write error code 6, how to make good waiting in comm GPIB

  Hello!

  I use a MUX Keithley and a digital Voltmeter to measure different values in my system, including the resistance of the wire 4. My project runs for several hours without any problem, but last night I got an error after about 8 hours DURATION. My mistake in the main vi shows the following error:

  GPIB Write in A_4Wire_resMUX_2!1,2!3,2!5_new.vi Error code 6.
  

  I have attached this Subvi, as you can see, I put a while loop in the Subvi to give enough time to measure 4 son to do. But of course maybe another function GPIB write hangs in the Subvi, not that after the while loop.

  I have 2 questions:

  1. What is the best way to make the error handling in comm GPIB, so I could see on my final mistake on what caused the problem in this certain sub - VI?

  2. can someone show me what I could do better in this sub - VI, in order to avoid possible errors of GPIB?

  Its just guessing, but I think the error comes from that I can't give enough time to the GPIB device to perform an action, then the next writing of GPIB breaks down?

  more information: Windows XP, LabView 2010 full version

  Thanks much for the advice and help!

  2001 pilot

  7001 driver

  Now that you have a modern version of LabVIEW why are you not taking advantage of the instrument driver network?  VISA is beautiful and 488,2 gross primitives should consider as "obsolete".

  Since you did not use the specific instrument driver vi we cannot say that write on this device generates the error that you are experiencing.

  So to specifically answer to Q1.  Use the driver found on the instrument driver network - they are tested and structured in a way to help debug your application and to take advantage of the powerful features of VISA...

  And (2) (see #1) and change the sequence stacked in a state machine

• HP Envy 4520: new HP Envy 4520 error code Oxc4eb800 at startup?

  Very frustrating that the printer is brand new and I even not at the installation stage to add the cartridges or paper. "Error code oxc4eb800 when up... have tried engine ERS power on" method, but does not... I have literally this just taken out of the box and in this case... .Please help... I, m at a loss.

  Welcome to the HP Forums.
  I hope that you are well @Patrik1,

  I read the error message/code you see on your urge for 4520 and I wanted to respond to troubleshoot!

  Please visit the link below and try the reset for this error. If the error persists, call the helpline to discuss a replacement printer.

  "' 0xc19a0005" or similar error screens

  If you have trouble, let me know and I'll do my best to help.

  Hit the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.

  Have a nice day

  HP technical support are available by clicking on the following link:

  http://support.HP.com/GB-en/contact-HP/

  (1) once the page opens, please select the country in which you are located. Then enter your model of HP on the right number.

  (2) then choose "Contact the Support" tab at the top and scroll to the bottom of the page "HP Support - contact" to fill out the form with your details.

  (3) Once finished, click the "Show Options" at the bottom right.

  (4) Finally, scroll to the bottom of the page and select "Get a phone number." A file number and telephone number will now fill for you.

• Get visa error 1073807194 after the power of the instrument cycle

  Hello and thanks in advance,

  I connect to an instrument via VISA with the port and IP address of the device. Normally, this works well, but if the loss of instrument (and camp) power during execution of the VI, LabView must be restarted for the VI to work again. (It's all labview, not only my VI). Error code: 1073807194 | VI_ERROR_CONN_LOST | The connection of the given session has been lost. None of these instabilities occur when only one connection is disrupted and restored. It is still a valuable resource for VISA. Can I solve this problem by disabling the port or plug and if so, how? I wish to insert a code to check if the connection is blocked and if so, erase it.

  I'm under LV 8.6 on Windows XP using measurement and automation to assign the resource VISA by manual selection of the socket. The VI is attached.

  This thread is useful, but the links are dead: http://forums.ni.com/t5/LabVIEW/visa-write-connection-has-been-lost/m-p/342028.

  Thank you very much!

  When you quit LabVIEW, and restart, LabVIEW automatically close all Sessions VISA.  Try to use the function of re-closing VISA close the existing session and open a new one.

• Error Code 37 running labview 6 with windows XP

  I checked most of the posts about this generic error code 37. Here's my dilemma... Labview 6 running on a windows NT system. This computer is on its last breath, and we want to switch to XP... I installed labview 6 on a XP machine and the program works very well... and I actually get my external device data unless I get the ERROR 37... the great thing is I can not launch a Subvi, which creates a linear between because once I get error 37, stops the Subvi. I don't understand how can I read data from my external device, still get the device not found msg. I even tried to install 7 LV and LV 8 still get the same results.

  To close the Communication port, you could create a new white vi, ask a close visa on the block diagram, he points to the port to close and run the vi.

• Windows Update 80070005 error code

  original title: error code 80070005

  Whenever I try to run windows update I received the error code 80070005.
  I tried to disable McAfee and a new attempt to update but get the same error.
  The update history shows no automatic updates since July 08.
  How can I fix it?

  Hello Kumbo,

  Method 1: please visit it mentioned below links MS for resolutions. Hope this can solve your problems,
  http://support.Microsoft.com/kb/816731

  http://support.Microsoft.com/kb/968003

   

• Windows updates: error code 80040154

  No updates have been installed successfully in more than a month... What is the problem? Error code: 80040154... using Windows Vista basic

  * Title *.
  My Windows Vista Basic does not accept windows updates: error code 80040154. What is the problem?

  Alan,
  If you have not already opened him a pension case and you still get this error, here are a few things to try.
  Run these tools and see if one of them report errors that cannot be fixed:
  Disk error checking
  System File Checker  
  The system update tool

  If those who invent it own and you still have a problem you can run some virus\malware scan from another source and then your.  Take a look at these links because they have some great info on virus protection:
  Get rid of malware 
  Can I clean an already infected computer?   
  Windows Live OneCare Safety Scanner Windows 7\Vista

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Error code 80240016 failed to update Windows Update

  Hello

  I've recently noticed that I had problems installing anything new from microsoft.  Last week, I tried to download internet explorer 8, but he repeated that the link was broken.  Then I tried to download other things on the microsoft Web site, and I got the same message.  Now, the update of windows tried to install service pack 1 and it is said, could not be updated with 80240016 error code - saying it currently installs other updates.  I think the problem is that the computer can't download anything from microsoft, any help on this would be appreciated.
  Thank you

  Hello Alex817,

  Thank you for using Microsoft Vista answers Forum!

  Since you have not found the option run as administrator of the normal mode, I would say that you follow step in the link in safe mode. To correct these goal, also try and create a new admin account and see if you can run the program as administrator of the normal mode.

  How to start in safe MODE

  1. Restart your computer if it is running.
  2. Press the F8 key after your computer powers initially.
  3. Once you see the menu Advanced Startup Options , you can stop tapping.
  4. Up/down arrow keys to highlight your selection.
  5. Select Safe Mode with network and press enter.
  6. You should see loading drivers and then Please wait.
  7. You should then be on the Welcome screen.

  Connect to your computer using an account with administrator privileges.

  Here is the link to new http://support.microsoft.com/kb/957307

  If please reply and let us know if your problem is resolved or if you need more help

  David O
  Microsoft Answers Support Engineer
  Visit our and tell us what you think.

• Update KB981715, 8007006e, Windows 7 Home Premium, Office Pro 2007 error Code

  Kept getting a notice of update for KB981715.  After download, kept getting the 8007006E error code.  I am running Windows 7 and Microsoft Office Pro 2007.

  AAA93,
  Run the following tools and then try to install the update again.  Let us know the results of the tools.

  System File Checker

  Update of the system analysis tool Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.