visitor's ability to log in. - need to set up a visitor access to a Wi - Fi hotspot

How can I configure visitor access to the Wi - Fi hotspot at home is not using my... secured network need to put in place the second network...  I have linksys

If I understand you correctly, you have a configuration of wireless network in your home and you want a second, network isn't secure wireless for customers.

Start reading the instructions here--> http://ezlan.net/shield.html
Instead of follow the directions to disable the part of the second router wireless, what you want to do is to configure two routers so that their wireless signals is separated as far as possible (see the second paragraph after the heading 'Note' on the linked page).

Ideally, routers should also be physically separated as much as possible.  Set a router to use channel 1 and the other router to use channel 11.  You may still experience some problems of interference between your two routers or between one of them and router is a close neighbor set to the same channel.

Tags: Windows

Similar Questions

  • You need to set the drive letter to the USB Ports front before any device has been inserted - that won't change when the device is connected. I have Windows XP Professional with Visual Studio 6 installed

    You need to set the drive letter to the USB Ports front before any device has been inserted - that won't change when the device is connected. I have Windows XP Professional with Visual Studio 6 installed. Thanks for your help

    diana73,

    First of all, make sure that you're connected Administrators account to do.

    How to change a drive letter to change an existing drive letter on a drive, on a partition, or a volume, follow these steps:

    1. Sign in as an administrator or as a member of the Administrators group.
    2. Click Start , click run and type compmgmt.msc .
    3. In the left pane, and then click disk management .
    4. Right click on the drive, the partition, the logical drive or volume that you want to assign a drive letter to and then click change drive letter and paths .
    5. Click change .
    6. Click assign the following drive letter if it is not already selected, click the drive letter that you want to use, and then click OK .
    7. Click Yes when you are prompted to confirm the drive letter change.

    The letter of the drive, partition, or volume that you specified is changed, and the new drive letter is displayed in the appropriate drive, partition, or volume in the disk management tool.

    Good luck! Please rate me upward if you find my post helpful. Thank you!

  • BlackBerry Smartphones Newbie needs help setting up email

    Hello world

    I've been the proud owner of a "BOLD" for about 48 hours now. This is my first Blackberry, so please bear with me.

    I need to set up my Yahoo email. I remember setting up front, but I deleted it as my allowance for the use of network (3 Australia) showed 2 MB roaming allowance, of which half was used in one day.

    I think that the e-mail message has been implemented via a browser page, but I can't go back to this page. The e-mail setup wizard seems to be to the establishment through BES which I did not. Does anyone know the address of the page?

    I also remember, when I chose the browser (not of Planet 3) I was taken in a BB page that showed several options of setting up various things. There were about 5 or 6 boxes grey listed above the other? Anyone also know the address of the page for this?

    Thanks for any help,

    Paul

    You also see a personal Email Setup on the device icon? If not try going into the Options | Advanced options | The host routing table. In this screen press press the button menu and choose to register now. See if you receive a message from check delivered to your device. Subsequently, reset the unit by removing the battery for 30 seconds. See if you have this icon now after restarting the device. If you still don't you can try setting up the account again on your carrier's Web site BIS to add return e-mail accounts?

    What options do you remember on this Web site? Try to go to mobile.blackberry.com on your browser and see if it's the page.

  • I need to set up my computer at home to print from a working remote desktop connection - how to put in place

    I need step by hep instructions on how to install one in my home computer can print remote desktop connection works.  OS 7 Pro work and home OS is Windows 7 home preuiem.  I don't know how to set options in local resources.  I just need to set up my printer driver or printer on the remote computer.

    Thank you

    Hello

    Thanks for posting your question in the Microsoft Community forums.

    I see from the description of the problem, you want to know how to configure the printer to print from the remote desktop connection.

    I will surely you help with this.
    I suggest that you set these settings before you connect and check if it helps.

    (a) Open Remote Desktop connection by clicking the Start button, clicking all programs , clicking Accessories, and then clicking Remote Desktop connection.
    (b) click on Optionsand then click the local resources tab.
    (c) under local devices and resources, Select the check box Printers .
    (d) click Connect to start the session.

    If the problem persists, I suggest you send the request in TechNet community to improve assistance in this regard. Please visit the link below to find a community that will provide the support you want.
    http://social.technet.Microsoft.com/forums/en/w7itpronetworking/threads
    Let us know the status of the issue after you perform the troubleshooting steps. If you need additional help or information on Windows, I'll be happy to help you. We, at tender Microsoft to excellence.

  • you really need to set up a place to enter bugs.   When you select a page in the Panel of the browser, then select all, the program crashes.   Acrobat CC on el capitan mac.

    you really need to set up a place to enter bugs.   When you select a page in the Panel of the browser, then select all, the program crashes.   Acrobat CC on el capitan mac.

    Hi, Hello, Hello, Hello, bongiorno.

    ==> Feature request/Bug Report Form

    .

  • What information do I need to set up a test server

    What information do I need to set up a test server

    After you have installed a local test server, go to the Site > manage sites & set your server to test local, as shown below.  In this example, I use WAMP server and my local site folder resides in the wamp\www folder.  On XAMPP or MAMP, the site folder is htdocs.

    Advanced tab

    Last screen

    Nancy O.

  • Need help setting up related content in HCM 9.1 PeopleTools 8.51

    I need help setting up related content in HCM 9.1 PeopleTools 8.51.
    I created a new service id in 'Set Related Content Service'. Its simple, it basically goes to google.com.
    Then I assigned Related Content for the Application Pages on the page «Manage the Configuration content to related» I'm my scenario, I've added it to the careers under the main menu.
    Then I went to the careers page, but the 'related information' link does not appear. How can I get this link to related information to appear at the top of the page/component?

    Thank you
    -Cory

    In order to get it work, there are a few basic server configuration requirements that you need in order to make it work.

    (1) define the field of authentication on the Web server
    (2) set the authentication of domain on the web profile
    (3) enable Single Sign-On

    The next in "My Oracle Support" document provides details on configuring content services.

    E-PORTAL: how to set up content related services. [984855.1 ID]

    In addition, here is a link to the PeopleBooks online that deals with the configuration of related content services.

    http://download.Oracle.com/docs/CD/E18083_01/pt851pbr0/Eng/psbooks/tprt/book.htm?file=tprt/htm/tprt20.htm#H3002

    In addition, there are also some know the limitations to the use of related content are different depending on the version of the tools you use.

    I hope this helps.

  • My computer won't let me log on to my account directors and cant access programs that need administrator permission

    Log cant administrator account and it is not removed is where I was logged in and then shut down my computer and then I could not connect more please help

    When I try to log the log service failed and I already tried safe mode and I can get on the account but my computer won't let me access programs and areas requiring permission for administrators

    Hello

    When you log in Mode safe mode, it accepts the password for your administrator account? In Safe Mode, open Control Panel and select user accounts. It shows on your account administrator?

    If so, while in Safe Mode, select Start Programs/Accessories/tools system. Click on System Restore .

    1. click on the Next button. Place a check mark to show more restore Points.

    2. Select a restore point with a date and time before when you saw for the first time this question.

    3. press the Next button. Click the Finish button.

    Start System Restore and restart the computer. Make sure that it ends completely before doing anything.

    NOTE: Using Safe Mode system restore is permanent. You will not be able to cancel the system restore process.

    Let us know the results.

    Thank you for using Windows 7

    Ronnie Vernon MVP

  • Need help setting up WebUI for the Wireless Gateway

    I have problem installing a Web UI for my demo project.

    I just do temperature is a simple application of WSN on a node of thermocouple WSN-3121 and it logging on a RT NI 9792 wireless gateway.

    Then, I wanted to create a web user interface and display whats in the user interface of the gateway - see the project.

    SO I'm stuck with the web INTERFACE coming.  I tried to read as much as I can but I still don't know what I'm doing wrong.

    As far as I see it, I need to create a web service in the construction for my gateway specifications and place the gateway_main.vi like the vi to use.  Then build and deployment.  Once it happened, and I run the vi on the bridge, I created a Web user interface as shown in the picture, where it counts the the gateway web service using 192.168.0.16:8080 - that works very well.

    When I run the Web interface, it is just and expires.

    I am using LAbview 2010.  Help, please.

    Hello markza,

    Your approach using the Web user interface designer and understanding its use case is quite accurate, the question lies in the web service, you have deployed. The VI you build as web service, which is gateway_main.vi, while loops inside and so cannot be used as a web service. The reason for the timeout is that your user interface Builder application calls the web service LV2010 and is stuck there for waiting time loops to complete. Also, the data type of cluster is not supported in the user Web interface Builder, so you'd have to break up from the entrance of the time of picking for the node wireless in two separate digital inputs.

    I recommend creating a Subvi out of your code inside of the while loop inside gateway_main.vi. The Subvi must have two digital inputs to replace the cluster (as mentioned above) and do not have one of the Boolean inputs Start or Stop. Output would remain the same, that is, two doubles and a Boolean value.

    I would like to know if this is useful and if you have any other questions.

    Thank you!

    Dieudonné jgfcnbh

    The user of LabVIEW Web R & D interface generator

  • Need help setting bios to boot from the cd. I did already but the laptop does not start again for cd player.

    Hello

    I forgot that my administration windows log password after the holidays.  I have loaded down a free program called Ophcrack and had set my laptop to boot from cd 1 but I just cannot get the laptop to boot from a cd.  He just continued boot from the internal hard disk.

    The cd is an image and it is bootable on my desk.

    The model of laptop: laptop HP ENVY m6

    Product number: C2N77UA #ABL

    BIOS version: F.25

    Processor type: Intel Core i7-3632QM CPU @ 2.20 GHz

    OS: Windows 8.1

    I only did a password reset disk (I'm learning the hard way now!).

    I don't want to do a "System Recovery" because I have some data on it.

    I realize there are paid there password recovery tools windows, but I would like to use this 'free' program to try to break 1.

    I just need help / instructions to set the bios for laptop can be started from a cd.  I also tried to boot from a key USB but the laptop kept begin its internal drive.

    Help, please.  Thanks a ton!

    Ted

    Hi Ted,

    You are welcome

    Boot into the bios menu and go to the very section where you have disabled the Secure Boot.

    Find an entry called materials and this value to Activate.

    Save the changes and exit the bios.

    Follow the previous procedure below:

    Insert the bootable disc of Ophcrack and laptop stop.

    Tap away at the esc you key start Notepad to open the Start Menu.  Select boot options ( f9 ), use the arrow keys to select the CD/DVD drive and press ENTER.  You can also get a prompt to "Press any key to" continuous - it if requested.

    Kind regards

    DP - K

  • How can I prevent the Contacts log? someone has set up on my pc without my permission

    Someone has recently implemented a 'Contactlog' on my pc that saves my activity on Hotmail. I suspect it's my partner who suffers from paranoia and was made without my permission or knowledge since March 09 from the journal. Please can you advise how I stop it / remove it. I tried to delete the log that is in a format txt, but it says that it cannot remove that another program is underway elsewhere when I see everything open. Please can you help me.
    Thank you

    Log on to an administrator user account and see if Parental control is activated for your own user account. If they are, disable them. If you use an administrator (not recommended) account, and therefore Parental controls are not involved, there must be a third party controlling the installed software. You need to know is that the program monitoring and contact their technical support. MS - MVP - Elephant Boy computers - don't panic!

  • 2911 ISM and CUE: need to (re) install CUE to access GUI?

    All the experts out there, I am a volunteer for installation of the IPT (voice) for my church.  They have a 2911ISR router that I'm trying to install / set up for a small Office Setup.

    The question is stated: need to (re) install CUE to get the GUI (web Interface) to work?  It comes with CUE 8.6.6 on module ISM-SRE-300-K9.  But I don't know if it's because the GUI isn't here or if I have configured the interfaces and route incorrectly.

    Here is the list of software on the ISM:

    MACC-2911-CUE # sh inst soft its
    History of Software Installation:
    See install.log for more details

    2014-03-19 12:48:39 * Install Publ. command * cmd: Opt 1: 0, Pkg:cue - allapps.sme.8.6.6.pkg Url:ftp://10.1.1.1// Mode: 1 Proto:1 host: 10.1.1.1
    2014-03-19 12:56:41 * CLEANED SOFTWARE *.
    Timestamp subsystem Version Description UID
    2014-03-19 12:56:42 Thirdparty 8.6.6 Service motor Thirdparty Code a3442277-7890-4782-9e6b-9d19efc1e0d8
    2014-03-19 12:56:42 plugin Enablement 8.6.6 enablement Plugin pack 26bd663c-3e5a-43d9-a6c3-5441ce44941b
    2014-03-19 12:56:42 languages of linguistic support for voicemail 8.6.6 IDENTIFIES global pack e2e81cc6-39b5-47e1-9f83-b83c897fc50c
    2014-03-19 12:56:42 overall 8.6.6 Global manifest edceaf0b-a890-4045-9086-5452fac85eba
    2014-03-19 12:56:42 infrastructure 8.6.6 Service engine Infrastructure a36e1be1-ce8a-4f53-ace7-1844262aa0b9
    2014-03-19 12:56:42 LPG Infrastructure 8.6.6 Service engine LPG Infrastructure 9f112eb1-6f58-4dd4-8faa-8530467af3b9
    2014-03-19 12:56:42 Voice Mail 8.6.6 Voicemail application 8e7823e2-0e92-4470-8860-653246345f9d
    2014-03-19 12:56:42 CUE Voicemail UK English 8.6.6 British English language pack fa803d25-9c89-4171-a14c-ec12d6ed6b8c
    2014-03-19 12:56:42 Bootloader 2.1.36 (secondary) Service Engine Bootloader 9d7b26fb-21b2-416e-8b65-425c2f8da5d8
    2014-03-19 12:56:42 8.6.6 installer Installer a0fb9f0a-fa5c-4b21-a64c-0cb9d6379573
    2014-03-19 12:56:42 core 8.6.6 engine OS Core Service 430f25f9-0fed-48a4-b362-823937138501
    2014-03-19 12:56:42 standard automatic Telephony Service Infrastructure 8.6.6 engine e3db91b0-f47d-460c-ad22-65001a5d45a9
    2014-03-19 13:01:48 * CLEANED SOFTWARE *.
    Timestamp subsystem Version Description UID
    2014-03-19 13:06:40 * CLEANED SOFTWARE *.
    Timestamp subsystem Version Description UID
    2014-03-19 23:17:44 * CLEANED SOFTWARE *.
    Timestamp subsystem Version Description UID
    2014-03-19 23:41:53 * CLEANED SOFTWARE *.
    Timestamp subsystem Version Description UID
    2014-04-20 17:47:59 * CLEANED SOFTWARE *.
    Timestamp subsystem Version Description UID
    See install.log for more details

    Can you confirm the GUI files are there or they lack; in which case I need to (re) install CUE?

    Thanks in advance for any help you can provide.  It is greatly appreciated.

    Shutdown?

  • Need help setting up switch SG300-10

    Hello

    I bought a SG300-10 switch and configuration.

    I have a problem to set up it causes that I'm not really used to networking.

    what I set up at the moment is the VLAN.

    VLAN 2 - step my router it for internet access

    Vlan10 - is for my server and pc in my office

    VLAN 40 - is for the wifi of comments.

    I will use the mode switch layer 3 and I want to configure a DHCP server on the vlan 40 but I'm not very well how to do.  I activated the DHCP and created a pool of ip but how I assign on the vlan 40? and how to set up everything to go on the internet? If I followed the basic logic, I will put all my members of port of vlan 2, is that correct?

    IM new in the field of networking

    Thank you

    Hi Justin,

    Here is some basic information for the switch. With VLAN, it is tag VLAN and remove the brand VLAN. A package of UNTAG means in the package header, there is no VLAN ID. The switch will provide separate from the client connection based on the transfer of bridge table. Usually UNTAG VLAN is used for the client connection. A beacon packet contains the VLAN ID in the header. In general, tag packets is used between other network device. An access port is member of 1 VLAN that is not marked. A trunk (on small business product) port is a port that has 1 UNTAG VLAN (VLAN native) and has the ability to tag the VLAN extra.

    Some examples of configuration CLI for tag and remove the brand VLAN. Keep in mind, VLAN 1 is the default VLAN, therefore, unless you make sure, VLAN 1 will default.

    To create a VLAN 2 on your switch

    Configure the terminal

    database of VLAN

    VLAN 2,3,4

    This will create the VLANs 2, 3 and 4

    To configure an IP address to a VLAN

    Configure the terminal

    interface vlan 1

    IP 192.168.1.254 255.255.255.0

    interface vlan 2

    192.168.2.254 255.255.255.0

    interface vlan 3

    192.168.3.254 IP address 255.255.255.0

    interface vlan 4

    IP 192.168.4.254 255.255.255.0

    Keep in mind, VLAN 1 must have a static IP address before you assign any other VLAN an IP address, or the switch will "lock".

    To assign an access as a member of the VLAN 1 port

    Configure the terminal

    Article IG1 interface

    switchport mode access

    To assign an access as a member of VLAN 2 port

    Configure the terminal

    interface hi2

    switchport mode access

    switchport access vlan 2

    If you check the GUI you'll notice port 1 is "1u" and port 2 is "2u".

    To create a trunk and assign some VLAN-

    Configure the terminal

    interface IG3

    switchport mode trunk

    switchport trunk allowed vlan add 2

    In the GUI, you will notice 3 port will be "1u, 2 t".

    To configure a port to have a VLAN different other that 1 as it removes the brand on a chest.

    Configure the terminal

    interface IG4

    switchport mode trunk

    switchport vlan trunk native 2

    switchport trunk allowed vlan add 3.4

    On the GUI, it will show '2u, 3 t, 4 t'

    Now that we have fundamental port assignment of the road, you can work on DHCP and IP address management.

    When the switch is in mode layer 3, if there is an IP address assigned to a VLAN, it is a switch virtual interface (SVI). The IP address of the service VLAN as default gateway which connects to this VLAN. The switch can associate the pool DHCP IP interface created on the switch-based layer 3.

    Firstly, we must establish your first jump of the switch - the default gateway of the switch statement. If you have a router connected to the SG300 you must assign the SG300 default gateway, which is the IP address of the router.

    Configure the terminal

    Default IP gateway 192.168.1.1

    Then you can concentrate on your DHCP scope. To configure a server DHCP table here is an example-

    network IP dhcp pool PRODUCTION

    address 192.168.2.1 low high 192.168.2.253 255.255.255.0

    Infinite rental

    default router 192.168.2.254

    dns-Server 8.8.8.8

    This basic table DHCP said many things.

    The name of the table is the PRODUCTION, this can be anything you want.

    low address is the first IP address that is assignable in the pool while high address is the last

    infinite lease means that had not expired DHCP lease

    Router by default, it is the most important. It is the default gateway, that the switch will be assigned to the customer. This is very important if you want router between VLAN or upstream of the internet

    DNS server, this allows to resolve the name instead of having to use IP only.

    Now, if you connect to a computer that is enable DHCP where VLAN 2 is not marked, you should receive an IP address that is assigned by the switch on this computer. Notice that the pool is a number of address IP 2 VLAN. The definition of IP pool, this is how it will bind to one VLAN, by matching the subnet.

    Now, once you have all the basic configuration complete, as Marty says, depending on the capacity of your router, it will need to need to support VLAN tagging, interface sub dot1q OR, as Marty has said, it would need static route to allow to your additional subnet route on the internet.

    Hope this will help you get on your way.

    -Tom
    Please mark replied messages useful

  • Need help setting up DB Link from my Oracle 11 g XE to SQL Server.

    Hello

    I am trying to create a link to DB from my Oracle 11 g Express Edition on a Windows XP computer to a SQL Server. Here are the steps I've done so far.

    1. creating and setting up a connection to the DB SQL Server ODBC. Baptized SQLSERVER. Authenticated by Windows.
    2. updated the listener.ora. See below.
    SID_LIST_LISTENER =
  (SID_LIST =
    (SID_DESC =
      (SID_NAME = PLSExtProc)
      (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
      (PROGRAM = extproc)
    )
    (SID_DESC =
      (SID_NAME = CLRExtProc)
      (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
      (PROGRAM = extproc)
    )
    (SID_DESC =
      (SID_NAME = SQLSERVER)
      (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
      (PROGRAM = hsodbc) 
    ) 
  )

LISTENER =
  (DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
      (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
    )
  )

DEFAULT_SERVICE_LISTENER = (XE)
    3. updated the tnsnames.ora. See below.
    XE =
  (DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
    (CONNECT_DATA =
      (SERVER = DEDICATED)
      (SERVICE_NAME = XE)
    )
  )

EXTPROC_CONNECTION_DATA =
  (DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
    )
    (CONNECT_DATA =
      (SID = PLSExtProc)
      (PRESENTATION = RO)
    )
  )

ORACLR_CONNECTION_DATA = 
  (DESCRIPTION = 
    (ADDRESS_LIST = 
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1)) 
    ) 
    (CONNECT_DATA = 
      (SID = CLRExtProc) 
      (PRESENTATION = RO) 
    ) 
  ) 

SQLSERVER = 
  (DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT=1521))
    )
    (CONNECT_DATA =
      (SID = SQLSERVER)
    ) 
  (HS = OK)
)
    4. copy C:\oraclexe\app\oracle\product\11.2.0\server\hs\admin\initdg4odbc.ora to C:\oraclexe\app\oracle\product\11.2.0\server\hs\admin\initSQLSERVER.ora and has changed. See below.
    # This is a sample agent init file that contains the HS parameters that are
# needed for the Database Gateway for ODBC

#
# HS init parameters
#
HS_FDS_CONNECT_INFO = SQLSERVER
HS_FDS_TRACE_LEVEL = off


#
# Environment variables required for the non-Oracle system
#
#set <envvar>=<value>
    5 restarted listener.
    C:\>lsnrctl stop

LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 18-SEP-2012 11:33
:51

Copyright (c) 1991, 2010, Oracle.  All rights reserved.

Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
The command completed successfully

C:\>lsnrctl start

LSNRCTL for 32-bit Windows: Version 11.2.0.2.0 - Production on 18-SEP-2012 11:33
:54

Copyright (c) 1991, 2010, Oracle.  All rights reserved.

Starting tnslsnr: please wait...

TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Production
System parameter file is C:\oraclexe\app\oracle\product\11.2.0\server\network\ad
min\listener.ora
Log messages written to C:\oraclexe\app\oracle\diag\tnslsnr\PHAILORTD000012\list
ener\alert\log.xml
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1ipc
)))
Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1521)))

Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC1)))
STATUS of the LISTENER
------------------------
Alias                     LISTENER
Version                   TNSLSNR for 32-bit Windows: Version 11.2.0.2.0 - Produ
ction
Start Date                18-SEP-2012 11:33:57
Uptime                    0 days 0 hr. 0 min. 3 sec
Trace Level               off
Security                  ON: Local OS Authentication
SNMP                      OFF
Default Service           XE
Listener Parameter File   C:\oraclexe\app\oracle\product\11.2.0\server\network\a
dmin\listener.ora
Listener Log File         C:\oraclexe\app\oracle\diag\tnslsnr\PHAILORTD000012\li
stener\alert\log.xml
Listening Endpoints Summary...
  (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC1ipc)))
  (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost)(PORT=1521
)))
Services Summary...
Service "CLRExtProc" has 1 instance(s).
  Instance "CLRExtProc", status UNKNOWN, has 1 handler(s) for this service...
Service "PLSExtProc" has 1 instance(s).
  Instance "PLSExtProc", status UNKNOWN, has 1 handler(s) for this service...
Service "SQLSERVER" has 1 instance(s).
  Instance "SQLSERVER", status UNKNOWN, has 1 handler(s) for this service...
The command completed successfully
    6. link of database created by using the following command.
    create database link sqlserver using 'SQLSERVER';
    7. test using
    select * from "dbo.mytable"@sqlserver;

ORA-28545: error diagnosed by Net8 when connecting to an agent
Unable to retrieve text of NETWORK/NCR message 65535
ORA-02063: preceding 2 lines from SQLSERVER

select * from dbo.mytable@sqlserver;

ORA-28545: error diagnosed by Net8 when connecting to an agent
Unable to retrieve text of NETWORK/NCR message 65535
ORA-02063: preceding 2 lines from SQLSERVER

select * from mytable@sqlserver;

ORA-28545: error diagnosed by Net8 when connecting to an agent
Unable to retrieve text of NETWORK/NCR message 65535
ORA-02063: preceding 2 lines from SQLSERVER
    I followed the steps in this link but do not know where I was wrong. Someone can help me.

    http://www.DBA-Oracle.com/t_heterogeneous_database_connections_sql_server.htm

    Thank you
    Allen

    HS messages should go here: heterogeneous connectivity

    No problem with this type of installation.

    A glitch in your specific configuration

    >

    (SID_NAME = SQLSERVER)
    (ORACLE_HOME = C:\oraclexe\app\oracle\product\11.2.0\server)
    (PROGRAM = hsodbc)

    11 g, the executable file is dg4odbc.exe, so you have read PROGRAM = dg4odbc. (I could reproduce the error with wrong program setting).

  • The "Log FIles" in the coldfusion 9.01 administrator access error

    When I try to look at the log files in cfadmin, I get this error:

    Diagnosis:
    The isSystemLog method was not found. He doesn't are has no method with the method specified name and the arguments types or the isSystemLog method is overloaded with argument types ColdFusion cannot decrypt reliably. ColdFusion found 0 methods that correspond to the provided arguments. If it is a Java object and you verified that the method exists, use the javacast function to reduce ambiguity.
    The error occurred on line 283

    I have also noticed that the scheduled tasks 'Last Run' does not update. I enabled logging in cfadmin for scheduled tasks and created a scheduler.log with all the tasks being connected and running properly for this.

    I am at a loss here and really need help before going to live with that.


    The problem has been resolved, it seems that the update applies without error due to the fact that a mail app kept the cfperfmon_9.dll in open C:\windows\system32 which prevented the 9.01 update to crush the original.

    Thank you all for your help! works fine now.

Maybe you are looking for