VMotion compatibility guide
Hi all
Can someone help me find a compatibility guide for VMotion on HP servers. We run two HP DL380G6 servers with Intel® Xeon® X 5560 processors and you want to buy HP DL380 G7 servers with Intel® Xeon® X 5650 processors. I need to know if these different models will be able to vmotion.
Thank you
Kenny
Hi Kenny,
You can take a look at the following article.
Good luck.
Concerning
Franck
Tags: VMware
Similar Questions
-
vMotion compatibility Intel CPU
Hi all
I'm making reference to this document: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1991
Requirements of VMotion CPU compatibility for Intel processors
We have four servers BL460c G1 (Xeon 54xx CPU). I want to buy two new servers to replace 2 we have in an offbeat upgrade. The new servers are BL460c G7 (Xeon 56xx CPU).
In the above document, our current processor is part of Group C. Our new servers fit into Group E. There are instructions of compatibility vmotion for vMotioning fast between the groups C - D and D-e... but I need to know if I can vMotion the c.-e. group. Is this possible, or what I can not vmotion?
Thanks for your help!
The VMware Compatibility Guide for your research material and click on the CPU model. This will open a web page that shows all modes of EVC supported CPU.
André
-
If I have two servers from different manufacturers in the same cluster DRS (Dell and HP), but both with Intel E5600 processors, are there problems with vmotion compatibility?
See what VMware says:
Sometimes, the suppliers of processors introduced changes important architects in the same processor family (for example, 64-bit and SSE3 extensions). VMware identifies these exceptions, if it cannot guarantee a successful with vMotion migration.
Source: the CPU compatibility requirements
When you activate CVS for a cluster with Intel of E3 Xeon or Xeon E5 family processors that have different revision numbers (v2, v3, v4), a CVS base is necessary. This is due to new instruction sets is available in different revisions. Although the processors will be the basis of CVS, it is mandatory for all processors have the same sets of instructions to virtual machines.
As for the process of Xeon with different revisions, when you turn on VCA for a cluster with Intel Xeon processors even family (for example, E56xx, X56xx, L56xx), a CVS base is necessary. This is due to new instruction sets is available in different revisions. Although the processors will be the basis of CVS, it is mandatory for all processors have the same sets of instructions to virtual machines.
-
I have hp dl380p gen8. Intel xeon processor e5-2650 v2 @2. 60 ghz now I want to check VMware Compatibility Guide for my hardware, but there are 3-4 servers on the Internet of the VMware Compatibility Guide site. which is correct, that I can find. Please help me to find true material on the site Internet of the VMware Compatibility Guide
ESXi 5.5 u2 @.
BTW, this model shows only compatible from 55U3
-
The processors for vMotion compatibility
We have just upgraded to vSphere Essentials 6, Plus so we can take advantage of vMotion. We have built an almost exact replica of our existing Dell PowerEdge T420 server, so that we can have a high availability for virtual machines, they move from one physical server to another, depending on the needs. Looking through the documentation of DRS cluster, it is said that the processors 'must come from the same class of supplier (Intel and AMD) with the same family of compatible processor for migration with vMotion. . "(vSphere 5.5 Documentation Centre()'
Our current server has a processor of v2 Intel Xeon E5-2440 (8 cores, 20 MB of cache, 1.9 GHz). The seller we buy our new generation of server of door the same CPU model number (Intel Xeon E5-2440), but with 6 cores, 15 MB of cache, 2. 4 GHz. They have to special order the exact same processor, we currently have. We will encounter any problems if the rest of the hardware is the same, but the processors are slightly different? Same supplier, same family, same model number – only with fewer cores, less cache, more GHz. Is that what I should consider before moving?
Thank you!
Ben
Your processors are of different generations, the E5-2440 is a Sandy Bridge and the E5-2440 v2 is an Ivy Bridge, take a look here: http://ark.intel.com/compare/64612, 75263
And since they are from a different generation, you need to activate CVS in your cluster to the power of the machine virtual vMotion between these hosts, have a look here for more information on the CVS: KB VMware: best vMotion compatibility (EVC) processor support
-
The host cannot be admitted to the current cluster Enhanced vMotion compatibility mode.
Hello everyone
Here's the situation...
I have:
vSphere 5.1 Cluster with two 5.1 ESXi hosts and configuration VSA.
vCenter Server running on a virtual Windows Server 2012 machine.
Task: Transfer virtual vCenter to a physical machine.
I have install the physical machine with Windows server 2012.
Installed vCenter 5.5 (hosts Newer then the ESXi 5.1)
VSA installed Manager (VSA Cluster 5.5)
When go to VSA Manager I am introduced to the following screen...
Recover DOES NOT work!
Full move operation DOES NOT work!
It recognizes the Cluster AUV-> check availability (is online and OK)-> begins to create the Cluster VSA and it fails with the following error...
Move the cluster host
VSA HA Cluster
The host cannot be admitted to the current cluster Enhanced vMotion compatibility mode. Under voltage or suspension of the virtual machines on the host can use the CPU features hidden by this mode.
Could someone please help?
Thanks to you all! This problem has been SOLVED as follows...
- VCenter Server go to--> "C:\Program Files\VMware\Infrastructure\tomcat\webapps\VSAManager\WEB-INF\classes".
- Open the file "dev.properties" with Notepad
- Change the line that says "evc.config.baseline = lowest" to 'highest = evc.config.baseline' and save the file.
- Perform the SERVICES. MSC and reboot 'VMware VirtualCenter Management Webservices'
After that it of back in the VSA Manager and run it again 'Cluster of VSA recover'!
Now, the wizard should be able to add hosts to the inventory, create the HA Cluster and add hosts to the HA cluster and configure Cluster HA.
Done everything! :-)
-
FT/HA/vMotion compatibility
Hello
I hope that the forum does not mind this strange issue. I tried to continue my learning of vSphere and ESXI installed on a white box with i7-2600 machine, on the Intel H67 chipset. Everything works
I would now like to add a second esxi host, practice FT/HA/Vmotion. I intend to stick with the i7-2600 for the processor, but my question is, the motherboard chipset should it be the same? I have to stay with a motherboard that is H67?
Thank you.
-MN
Hello
Shorat response is "no, it doesn't have to be the same.
Slightly longer answer is:
For HA, it shouldn't make any difference if it's the same or not (mother or processor card). For FT, and vMotion processor count.
Although FT and vMotion are apparently completely different one from the other, FT is possible with vMotion, so, the first thing to do is to understand the vMotion compatibility.
The "only thing" vMotion to be is (apart from a shared storage, network connectivity, etc.) East of compatible processors between them. You can have a look on this
and this
http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1991
As you will see, processor questions and where you do not have the same processor, then you should play a little with VCA.
This is a compatibility table for EVC and the mask, you need to use in case you want to use two different processors
And in case you want to learn a little more about all these (basic knowledge), you can take a look in this doc.
http://www.VMware.com/files/PDF/vmotion_info_guide.PDF
I hope this has helped you!
Concerning
SEB
-
ESX 2.5.5 does support Windows 2003? -Online new vs Compatibility Guide OS compatibility guide
I'm pushing on with W2K3 on ESX 2.5.5. I think it's OK and believe that I've done it before.
"The Guide of the obsolete OS indicates W2K3 on ESX 2.0 and the online Compatibility Guide only covers ESX 3.0 and refers to discouraged on the tab"other"documents".
Can someone clarify and verify that W2K3 will work on ESX 2.5.5?
Thank you, all points will be awarded.
W2K3 works and is supported on ESX 2.5 - I doneit frequently.
If you find this or any other answer useful please consider awarding points marking the answer correct or useful
-
I am looking for a few new ESX boxes to expand our data center of VSphere 4 current U1.
Ideally, I would buy Intel E7540 series servers because they can FT and adapt the specifications I need.
I currently have a mix of X 5355 and E7330 ESX boxes.
DELL sales tell me that E7540 processors are not compatible with the existing X 5355 vmotion and processors E7330 (even with active CVS).
VCA and flexmigration enable me to vmotion (hot) between theses processors and processor E7540? I have the impression that the seller DELL is perhaps wrong as I thought VCA and flexmigration should mitigate the differences between these processors (obviously within reason)? Surely at least between the E7330 and the E7540?
I had a look to many documents, including the KB Article: 1003212 but still trying to find a definitive answer?
Forget DELL sales. They should be compatible under VCA VMotion (VCA's enhanced VMotion compatibility). But they are obviously not compatible FT.
---
MCSA, MCTS, VCP, VMware vExpert 2009
-
Anyone know if knew that Opteron 6200 (Interlagos) are compatible with Opteron 6100 (Magny Cours) VMotion?
VMware used to maintain an up-to-date list of processors with a compatibility matrix, but I didn't see a current copy of this document within a certain time. The last that I could dig up was 2008, so I ask my question here.
Also, if anyone knows of a compatibility matrix was updated that they could tell me, that would be helpful.
Thank you!
Allen Beddingfield
Systems engineer
The University of Alabama
Allen: I can confirm that VMotion works between Opteron 6100 and 6200 if you are using the CVS 'AMD Opteron Genesis 3 (no 3DNow!) '.
-
VMotion compatibility - different CPU
Sorry to post a question, but I just haven't found the answer in the readme guides and admin I have for 4.1. We use servers for our cluster, all HP DL380 G5 with the dual Xeon 5430 (quadcore). We are looking to add a few boxes to the cluster, and we will most likely go with the HP DL380 G7 beings are current servers are almost two years now. G7 will always have Xeon processors, but they will certainly have higher clock speeds to this processor will not match exactly. In my view, that this used to be a problem in the past, when he came to VM vMotioning fast between the two different cpu. My question is, is this even a question? If I stay within the Intel Xeon family, I'm ok for vmotion between two different cpu? The same of course, brand just diffenrent speeds and possibly different number of hearts.
Thank you
-scott
You may need to activate CVS for vMotion work
-
Intel's Nehalem VMotion compatibility - And current Xeon
Hi all
I was wondering if anyone can tell me if the processors Intel Nehalem will be compatible with the Xeon VMotion, I in my BL460c? I am looking into the possibility of adding some BL490c to our ESX cluster, once they are released, but I am wary of any possible difference in CPU.
If you enable CVS in your cluster, you should not have problems with compatibility.
-KjB
-
Intel Xeon 54xx vmotion compatibility
Hello.
If I understand correctly - vmotion on same family CPU should work without problem.
We got 3 nodes with Xeon 5410 and 1 node with Xeon 5430.
VMotion of 5410-5430 work is good.
But it works of 5430 to 5410 incompatibility NX/XD.
Hide allows a flag NX/XD, but he isn't very good resolution for us.
question 2:
(1) is on same family vmotion CPU should work without any problem?
(2) what do we lose if disable NX/XD indicator on each virtual machine?
(3) the concealment of NX/XD is better or worse then VCA?
NX/XD is only a function of the CPU, but there are others (like SSE).
So the good solution is VCA at the level of the cluster or CPUID mask at the virtual machine level.
I suggest that the VCA solution is very simple to implement.
Create a new cluster empty, enable CVS, move each ESX in the new cluster (the ESX must be in maintenance mode).
See also: http://kb.vmware.com/kb/1005764
André
-
Someone at - it a processors for VMotion compatibility table.
I have a bunch of two nodes and try to consolidate this number up to 3 or 4 knots, but I need to try to understand what are coincident with what processors. VMware has a chart, but for the life of me I can't find. I have HP and IBM blades and standard server systems. with a slew of old and new processors. Looking for a way to determine if I can match processors even if they match 100%. For example
HP ProLiant DL585 AMD Opteron Processor 848 G1, I can match with a
HP ProLiant DL585 G1 AMD Opteron Processor 852
Without masking of Vmotion and CPU still work.
Thanks in advance!
The HP ftp://ftp.compaq.com/pub/products/servers/vmware/vmotion.pdf
Also check Opscheck. http://www.vwire.com/free-tools/opscheck
VMware http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1003212 link
-
Sanity Check: Hardware compatibility: vMotion/CPU/VCA etc.
Hi all
We currently have a DRS cluster with 6 hosts Dell Poweredge R610 with Intel Xeon 5540 or 5530 processors which, according to article KB (http://kb.vmware.com/kb/1991) are in Group D for the vMotion compatibility. (Nehalem-EP)
I want to add new hosts to the cluster and try again Dell R620s. These have Xeon CPU E5-2640. I can't find an article with the same level of detail for the new processors. The compatibility guide Vmware tells me that it is a Sandy bridge processor?
If I add hosts with newer processors to the cluster, be they work? Or do I have to turn on some sort of CVS mode?
If I read this article (KB VMware: best vMotion compatibility (EVC) processor support ) he gives to think that I would need to market the VCA Level2 (Nehalem). This would be 'disable' have the CPU features in the new host beyond what former processors... But what happens in 'x' time of years when all guests have disappeared - presumbaly I can then disable compatibility EVC mode so that all the features of the CPU are presented? This would have a negative impact on existing virtual machines?
Please could someone health mental check me or point me in the direction of something to reassure me?
Thanks in advance
NB. Currently on vSphere 4.0, but the upgrade to 5/5.1 soon.
I suppose that once the VCA mode is activated, it will always be equal to the level of the 'down' (older?) (In this case Nehalem) CPU level up to what the last host with Nehalem processors is removed from the cluster.
Yes, that's correct.
Maybe you are looking for
-
How to change the link colors after consulting with Firefox's search results?
All other browsers I used for searches always change the color or the color of the visited link. I just downloaded the latest version of Firefox, but does not do it anymore.
-
Canon MP 730 printer all-in-one more no signal my TX1000 HP pav. Entertainment Notebook PC
I have a Canon MP730 while a printer, a desk, a HP Pavilion Entertainment PC tx1000 laptop, a Wireless Linksys router. The linksys wireless router is connected to the internet, the desktop computer is connected to the linksys, the printer is connecte
-
Deleting a file that causes a buffer overrun
I downloaded a video file that gives me a buffer overrun. I can not remove this file to the trash or shread as these options stop working when I try to use them to make the tour of this file. I would appreciate your suggentions know how I can get thi
-
Can you get audio through the screen via a DVI - D connection? I have a HP x 2011 anda monitor HP Envy PC 700-050. Any help would be appreciated, thanks.
-
Hash value for Digital River Windows 7 Ultimate SP1, 32 and 64-bit downloads, Spanish
Hello. I read in other posts here that Digital River links are legitimate to download original ISOs, and I saw the hash values for downloads of ISOs, for the English language. Because of the site web of Digital River no longer exist, I would like to