VPN concentrator - using several authentication servers

Similar Questions

• 3000 VPN concentrator using ospf md5 authentication failed

  Hi all

  I just tested ospf with a 3005 VPN connected with a cisco router using ospf md5 authentication, but fail. Cisco router, I can see neighbouring State ospf is "INIT", but can not see any connection VPN 3005, physical connection is good, ping can be reached between them. I tried the command "ip ospf authentication message-digest & ip ospf authentication-key ' and"ip ospf message-digest-key"command in the router the password is the same in both sides and the md5 id has been set. But when I use simple authentication or disable authentication that the neighbor relationship can ride. Any body met this case before? Thank you!

  Best regards

  Teru Lei

  Hello

  This is a known bug, I also met this before: CSCef38044

  It is not possible to accumulate OSPF with newer versions of IOS, on which they'RE ability is enabled using MD5 hash neighborship. They'RE capa is activated somewhere of 12.2 T. This behavior can be found on CVPN 4.1.5 and above whose 4.7 also.

  I tested it with several IOS and OS CVPN - same result. The symptom: router ospf neighborship remains in the State INIT/DROTHER.

  Workaround is to configure the router:

  router ospf 1

  No they're ability

  This will solve your problem.

  Attila Suba

• 802.1 x (dot1x) with IP phone / workstation using several authentication domains (MDA)

  Scenario:

  Workstation (behind the phone)

  8.5 (2) software IP Phone 7911

  ACS 4.1 with AD on the same server

  Cisco switch WS-C3750E-24PD with c3750e-universalk9 - mz.122 - 53.SE1.bin

  Guide used:

  http://www.Cisco.com/en/us/Tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml

  http://www.Cisco.com/en/us/products/sw/secursw/ps2086/products_configuration_example09186a00801df0e4.shtml

  To accomplish:

  Computer and authentication of the IP phone with 802. 1 x. The phone using EAP - MD5 and the workstation with PEAP-MSCHAP version 2.

  Tried and worked:

  Workstation using EAP - MD5 (with ACS username) and use PEAP (with AD user name) and it also acceded to the vlan correct according to the username.

  The journal of the ACS, authentication failed:

  Message-Type-name of user - Group-Name-Caller ID - network access profile name - Code failure-authentic -.

  Authentic has no EAP type - CP 7911 G-SEP00254594D6BA--00-25-45-94-D6-BA VOZ - (default) - not configured

  Configuration of the Switch:

  Group AAA dot1x default authentication RADIUS

  Group AAA authorization network default RADIUS

  RADIUS-server host 10.32.250.250 auth-port 1645 acct-port 1646 borders 7 095F4B07110445425B54

  interface GigabitEthernet1/0/3

  switchport mode access

  switchport nonegotiate

  switchport voice vlan 200

  multi-domain of host-mode authentication

  Auto control of the port of authentication

  periodic authentication

  MLS qos trust device cisco-phone

  MLS qos based on vlan

  dot1x EAP both

  dot1x quiet-time 20

  dot1x timeout server-timeout 100

  dot1x tx-delay 100

  broadcast storm control 15.00

  multicast storm-control level 10.00

  spanning tree portfast

  spanning tree guard root

  Summary of ACS Configuration:

  Configured the AAA

  2 group - voice and data, each with their VLAN respective and the ACS configuration parameters (attribute / value (AV))

  Added the user name and password for IP phones

  Mapped the announcement to the DataSet

  A certificate and installed in the workstation

  Set up the configuration of global authentication, where I ticked the boxes PEAP and EAP - MD5

  So, as I said, it only authenticates the workstation w / IP phone.  When I add the IP phone it does not authenticate any of them.

  Someone at - it one day?

  Hello

  First of all, you can try a different sw for phone (for example 8.4.2S). I have a similar problem with the 8.5 software and phones 7945/7965. Secondary, you must attribute av-pair confiigure side ACS for the correct placement of the voice phone to vlan.

  Concerning

  Stanislav

• VPN concentrator + PIX on LAN-> customers can not reach local servers

  Hello

  I have a problem wrt. remote access clients coming via a VPN3000 concentrator and trying to access local servers.

  For the topology:

  The internal network is 10.0.1.0/24. It connects with the outside world, as well as via a PIX DMZ; the PIX has 10.0.1.1 in the internal network.

  On the same LAN (internal), I have the VPN concentrator for the inside address 10.0.1.5. It assigns addresses in the 10.0.100.0/24 range to the

  VPN client-PCs.

  I can sucessfully connect using the VPN client SW to the hub, i.e. remote access clients out addresses

  the 10.0.100.0/24 range.

  The problem: access from VPN clients to internal network is * not * possible; for example, a customer with 10.0.100.1 cannot connect to

  internal to the 10.0.1.28 server.

  To my knowledge, this is a routing problem because the server (10.0.1.28) has no idea on how to reach customers in

  10.0.100.0/24. The only thing that the server is a default static route pointing to the PIX, i.e. 10.0.1.1.

  So I set up a static route on the PIX for 10.0.100.0 pointing to the hub-VPN, that is

  Mylan route 10.0.100.0 255.255.255.0 10.0.1.5 1

  This does not solve my problem though.

  In the PIX logs, I see the entries as follows:

  % 3 PIX-106011: deny entering (no xlate) tcp src trainee: 10.0.1.28 (atlas) / 445 intern dst: 10.0.100.1 (pending) 1064

  The PIX seems to abandon return packages, i.e. traffic from the server back to the client

  To my knowledge, the problem seems to be:

  Short traffic VPN - client-> Concentrator VPN-> Server-> PIX - where it gets moved.

  My reasoning: the PIX only sees the package back, i.e. the package back from the server to the client - and therefore decreasing the

  package because he has not seen the package from the client to the server.

  So here are my questions:

  (o) how do I configure the PIX that I be connectivity between my remote VPN clients (10.0.100.0/24) and

  computers servers on the local network (10.0.1.0/24)?

  (o) someone else you have something like this going?

  PS: Please note that the first obvious idea, installation of static routes on all machines on the local network is not an option here.

  Thank you very much in advance for your help,.

  -ewald

  Hello, PIX the because can not route traffic on the same interface (prior to version 7.0 anyway), I suggest you two places your hub to the outside with the inside of the legs on a zone demilitarized or (if you can not do a makeover of the network) you remove your pool with 10.0.100.0 - addresses and create a pool with 10.0.1.0 - addresses which is a part of the address space. No, NOT all. A little book that it is not used inside.

  Best regards

  Robert Maras

• can I use mulitple Essbase servers if I have several web servers planning?

  Hello
  can I use mulitple Essbase servers if I have several web servers planning?
  Can I have a planning application of finance running on a Web server on a single server Essbase.
  Have another application of planning operations running on another Web server on another box of Essbase and server?
  Thanks in advance.

  Hello

  You can have a lot of servers that you want essbase, provided that they are registered on the same shared services. When you create a data source for the planning your application, you must provide Essbase server name and login. You can provide an essbase server to a source of data and another for another essbase server.

  Also, since planning is based on the RDBMS database, you can have multiple servers web planning pointing to the same planning application. You can use the concept of load balancer as well.

  Let me know if it helps.

  See you soon
  RS

• VPN Concentrator at the migration of ASA - auth problem.

  Hi all

  I'm migrating to remote access VPN (IPSec) VPN 3020 to ASA. Local authentication works very well. If I add the IAS radius for authentication servers, then I get the following error message

  Secure VPN connection terminated by a peer.

  433 reason: (reason unspecified peer)

  The capture of shows "access-reject" in back IAS server packages. IAS server is configured in the same way as the VPN 3020.

  I run the code to 8.0 (0) on the SAA. Any idea of what is the cause?

  Hello

  You specify the shared secret between asa and IAS?

  You specified in RADIUS server that ASA is allowed to send requests? In other words has specified that the SAA is a valid SIN?

  This link may be useful: http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806de37e.shtml

  I hope this helps.

  Best regards.

  Massimiliano.

• problem of traffic flow with tunnel created the network with a tunnel to a VPN concentrator

  Hi, I worked with Cisco and the seller for 2 weeks on this.II am hoping that what we are witnessing will ring a Bell with someone.

  Some basic information:

  I work at a seller who needs from one site to the other tunnel.  There are currently 1 site to another with the seller using a Juniper SSG, which works without incident in my system.  I'm transitioning to routers Cisco 2811 and put in place a new tunnel with the seller for the 2800 uses a different public ip address in my address range.  So my network has 2 tunnels with the provider that uses a Cisco VPN concentrator.  The hosts behind the tunnel use 20x.x.x.x public IP addresses.

  My Cisco router will create a tunnel, but I can't not to hosts on the network of the provider through the Cisco 2811, but I can't get through the tunnel of Juniper.  The seller sees my packages and provider host meets them and sends them to the tunnel.  They never reach the external interface on my Cisco router.

  I'm from the external interface so that my endpoint and the peers are the same IP address.  (note, I tried to do a static NAT and have an address of tunnel and my different host to the same result.)  Cisco has confirmed that I do have 2 addresses different and this configuration was a success with the creation of another successful tunnels toa different network.)

  I tested this configuration on a network of transit area before moving the router to the production network and my Cisco 2811 has managed to create the tunnel and ping the inside host.  Once we moved the router at camp, we can no longer ping on the host behind the seller tunnel.   The seller assured me that the tunnel setting is exactly the same, and he sees his host to send traffic to the tunnel.  The seller seems well versed with the VPN concentrator and manages connections for many customers successfully.

  The seller has a second VPN concentrator on a separate network and I can connect to this VPN concentrator with success of the Cisco 2811 who is having problems with the hub, which has also a tunnel with Gin.

  Here is what we have done so far:

  (1) confirm the config with the help of Cisco 2811.  The tunnel is up.  SH cyrpto ipa wristwatch tunnel upward.
  (2) turn on Nat - T side of the tunnel VPN landscapers
  (3) confirm that the traffic flows properly a tunnel on another network (which would indicate that the Cisco config is ok)
  (4) successfully, tunnel and reach a different configuration hosting
  (5) to confirm all the settings of tunnel with the seller
  (6) the seller confirmed that his side host has no way and that it points to the default gateway
  (7) to rebuild the tunnel from scratch
  8) confirm with our ISP that no way divert traffic elsewhere.  My gateway lSP sees my directly connected external address.
  (9) confirm that the ACL matches with the seller
  (10) I can't get the Juniper because he is in production and in constant use

  Is there a known issue with the help of a VPN concentrator to connect to 2 tunnels on the same 28 network range?

  Options or ideas are welcome.  I had countless sessions with Cisco webex, but do not have access to the hub of the seller.  I can forward suggestions.

  Here's a code

  crypto ISAKMP policy 1
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 2
  BA 3des
  preshared authentication
  Group 2

  Crypto ipsec transform-set mytrans aes - esp esp-sha-hmac

  Crypto-map dynamic dynmap 30
  Set transform-set RIGHT

  ISAKMP crypto key address No.-xauth

  interface FastEthernet0/0
  Description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE $ 0/0
  IP 255.255.255.240
  IP access-group 107 to
  IP access-group out 106
  NAT outside IP
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  crypto mymap map

  logging of access lists (applied outside to get an idea of what will happen.  No esp traffic happens, he has never hits)

  allowed access list 106 esp host host newspaper
  106 ip access list allow a whole
  allowed access list 107 esp host host Journal
  access-list 107 permit ip host host Journal

  access-list 107 permit ip host host Journal
  107 ip access list allow a whole

  Crypto isa HS her
  IPv4 Crypto ISAKMP Security Association
  status of DST CBC State conn-id slot
    QM_IDLE ASSETS 0 1010

  "Mymap" ipsec-isakmp crypto map 1
  Peer =.
  Extend the 116 IP access list
  access - list 116 permit ip host host (which is a public IP address))
  Current counterpart:
  Life safety association: 4608000 kilobytes / 2800 seconds
  PFS (Y/N): N
  Transform sets = {}
  myTrans,
  }

  OK - so I have messed around the lab for 20 minutes and came up with the below (ip are IP test:-)

  (4) ip nat pool crypto-nat 10.1.1.1 10.1.1.1 prefix length 30 <> it comes to the new address of NAT

  !
  (1) ip nat inside source list 102 interface FastEthernet0/0 overload <> it comes to the interface by default NAT

  !
  IP nat inside source map route overload of crypto-nat of crypto-nat pool <> it is the policy of the NAT function

  !

  (6) access-list 101 permit ip 172.16.1.0 0.0.0.255 172.16.2.0 0.0.0.255 <> defines the IP source and destination traffic

  !

  (2) access-list 102 deny ip 172.16.1.0 0.0.0.255 172.16.2.0 0.0.0.255 <> does not NAT the normal communication

  (3) access-list 102 deny ip 10.1.1.1 host 172.16.2.0 0.0.0.255 <> does not re - NAT NAT

  (1) access-list 102 permit ip 172.16.1.0 0.0.0.255 any <> allows everyone else to use the IP Address of the interface for NAT

  !

  (5) crypto-nat route-map permit 5 <> condition for the specific required NAT
  corresponds to the IP 101 <> game of traffic source and destination IP must be NAT'td

  (7) access list 103 permit ip 10.1.1.1 host 172.16.2.0 0.0.0.255 <> crypto acl

  Then, how the works above, when a package with the what IP 172.16.1.0/24 source wants to leave the router to connect to google, say the source will change to IP interface (1).  When 172.16.1.0/24 wants to talk to172.16.2.0/24, it does not get translated (2).  When the remote end traffic equaled the following clause of NAT - the already NAT'td IP will not be affected again (3) when a host 172.16.1.0/24 wants to communicate with 172.16.2.20/24 we need a NAT NAT specific pool is required (4).  We must define a method of specific traffic to apply the NAT with a roadmap (5) which applies only when the specific traffic (6), then simply define the interesting traffic to the VPN to initiate and enable comms (7) corresponding

• Help, please! Connected to the VPN, but cannot access internal servers.

  Hi friends,

  I'm a newbie on vpn stuff, I set up a base on a Cisco ASA 5505 vpn by using ASDM, and I was able to connect to it.  However, I can't ssh or RDP to one of the servers in the House after that I connected to the vpn.  Here is the configuration.  Help, please!

  ASA Version 8.2 (5)

  !

  hostname sc - asa

  domain abc.com

  enable the encrypted password xxxxxxxxx

  xxxxxxxxx encrypted passwd

  names of

  !

  interface Ethernet0/0

  switchport access vlan 2

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan1

  nameif inside

  security-level 100

  IP 192.168.1.1 255.255.255.0

  !

  interface Vlan2

  nameif outside

  security-level 0

  IP address dhcp setroute

  !

  passive FTP mode

  DNS server-group DefaultDNS

  domain OpenDNS.com

  sc-pool_splitTunnelAcl-list of allowed access standard 192.168.1.0 255.255.255.0

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  pager lines 24

  Enable logging

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  IP local pool sc-192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown cold start

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  interface ID client DHCP-client to the outside

  dhcpd outside auto_config

  !

  dhcpd address 192.168.1.5 - 192.168.1.36 inside

  dhcpd dns 208.67.222.222 208.67.220.220 interface inside

  rental contract interface 86400 dhcpd inside

  dhcpd abc.com domain inside interface

  dhcpd allow inside

  !

  a basic threat threat detection

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  SSL encryption rc4 - md5, rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1

  WebVPN

  abc group policy - sc internal

  attributes of the strategy of group abc - sc

  value of server DNS 208.67.222.222 192.168.1.3

  Protocol-tunnel-VPN IPSec

  Split-tunnel-policy tunnelspecified

  Split-tunnel-network-list value abc-sc_splitTunnelAcl

  field default value abc.com

  a001 xxxxxxxxxxx encrypted password username

  a002 xxxxxxxxxxx encrypted password username

  username a003 encrypted password privilege 0 xxxxxxxxxxx

  a003 username attributes

  Strategy Group-VPN-abc-sc

  a004 xxxxxxxxxxx encrypted password privilege 0 username

  a004 username attributes

  Strategy Group-VPN-abc-sc

  a005 xxxxxxxxxxx encrypted password username

  a006 xxxxxxxxxxx encrypted password username

  username privilege 15 encrypted password xxxxxxxxxxx a007

  remote access to tunnel-group abc - sc type

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  Group Policy - by default-abc-sc

  tunnel-group abc - sc ipsec-attributes

  pre-shared key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  type of policy-card inspect dns preset_dns_map

  parameters

  maximum message length automatic of customer

  message-length maximum 512

  Policy-map global_policy

  class inspection_default

  inspect the preset_dns_map dns

  inspect the ftp

  inspect h323 h225

  inspect the h323 ras

  inspect the rsh

  inspect the rtsp

  inspect esmtp

  inspect sqlnet

  inspect the skinny

  inspect sunrpc

  inspect xdmcp

  inspect the sip

  inspect the netbios

  inspect the tftp

  Review the ip options

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:e7df4fa4b60a252d806ca5222d48883b

  : end

  Hello

  I would suggest you start by changing the pool VPN to something else than the current LAN network and see if that helps

  These should be the configuration required to achieve this goal

  • First remove us pool setup VPN VPN
  • Then we delete the VPN Pool and create again with an another address space
  • When then attach this new Pool of VPN again to the VPN configuration
  • In the last step, we add a NAT0 / exempt for this new pool VPN NAT configuration and remove the old ACL line for the former group of VPN

  attributes global-tunnel-group-abc - sc

  no address-sc-swimming pool

  no ip local pool sc 192.168.1.100 - 192.168.1.110 mask 255.255.255.0

  IP local pool sc-192.168.100.100 - 192.168.100.110 mask 255.255.255.0

  attributes global-tunnel-group-abc - sc

  address sc-pool pool

  inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.100.0 255.255.255.0

  No inside_nat0_outbound access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.1.96 255.255.255.240

  -Jouni

• Unable to connect to the Cisco VPN you use native client: El Capitan

  I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

  When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

  * connect using the old work VPN connection: without success

  Config: Hand [server address, account name],

  AUTH settings [shared secret, the Group name].

  Advanced [mode to use the passive FTP = TRUE]

  errors:

  "authd [124]: copy_rights: _server_authorize failed.

  "raccoon [2580]: could not send message vpn_control: Broken pipe"

  ...

  * Add new VPN connection using L2TP over IPSec: without success

  Config: Hand [server address, account name],

  Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

  Advanced [send all traffic on the VPN = TRUE]

  errsors:

  "pppd [2616]: password not found in the system keychain.

  "authd [124]: copy_rights: _server_authorize failed.

  ...

  
  

  * Add new connection using Cisco via IPSec VPN: without success

  Main config: [server address, account name].

  AUTH settings [shared secret, the Group name].

  Advanced [mode to use the passive FTP = TRUE]

  errors:

  "authd [124]: copy_rights: _server_authorize failed.

  "raccoon [2580]: could not send message vpn_control: Broken pipe"

  VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

  I. Journal of Console app existing/Legacy VPN connection:

  26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

  26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

  26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

  26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

  26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

  26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

  26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 339 [2580]: connection.

  26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

  26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

  26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

  26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 405 [2580]: connection.

  26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

  26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

  26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

  26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

  26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

  26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

  26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

  26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

  26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

  [26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

  26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

  26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

  26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

  26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

  [26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

  26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  $VPN_SERVER_IP

  II. new VPN connection using L2TP over IPSec Console app log:

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

  26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

  26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

  26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

  26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

  26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

  26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

  26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

  26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

  26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

  26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

  26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

  26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

  26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

  26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

  26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

  26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

  26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

  26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

  26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

  26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

  26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

  III. New connection of Cisco VPN through IPSec Console app log:

  26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

  26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

  [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

  [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

  26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

  26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

  26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

  26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

  26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 296 [2576]: connection.

  26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

  26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

  26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 374 raccoon [2576]: connection.

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

  26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

  26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

  26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

  26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

  26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

  26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

  26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

  26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

  [26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

  26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

  26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

  26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

  26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

  [26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

  26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  It seems that I solved the problem, but I'm not sure it helped.

  After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

• VPN concentrator to transmit user group information to the IAS server?

  All,

  the feeling that the answer will be no, but we have replaced our MS RAS server using a VPN 3030 using an IAS server for authentication on a Win2k3 domain. The question we have is that some people share files FCP with people from other groups. HIA just validates the user password and verifies that they are in a private network allowed virtual group, which is then allowing them access more than they should, is it all the same for the hub the information on an IAS to control server as well? If not, does anyone know how to check popular ID using the remote VPN access are in the right group to which they are connected?

  Sorry I think I did the above clear as mud!

  Do not know your question, but you can cause the IAS server to assign a group to a user by adding the attribute class to a specific IAS security policy. Add class = OU = groupname; (do not omit the semicolon) for the attributes RADIUS IAS policy against which a user will be auth, and this will have an impact to the 3030, which will assign them to the appropriate group.

  I hope this helps.

• Configuration file for the VPN concentrator

  Hello

  I have a text-based VPN concentrator configuration file, and I want to know if there is a configuration guide of Concentrator VPN that I can use to refer to this file. The configuration on cisco.com guide is currently for the GUI based configuration.

  Furthermore, if there is a tool/utility that will read the configuration file in the format GUI without physical access to the device, which will also help.

  Thanks in advance for any assistance.

  There is a "XML export screen" in the management section of the files on the VPN concentrator. You can export the current configuration of the concentrator in a XML format, which provides the labels and values for the fields in the configuration file.

  http://www.Cisco.com/en/us/docs/security/vpn3000/vpn3000_47/Administration/Guide/Fileman.html#wpxref53361

• Cisco VPN Client behind PIX 515E,-&gt; VPN concentrator

  I'm trying to configure a client as follows:

  The user is running Cisco VPN Client 4.0. They are behind a 6.1 PIX 515E (4), and I need to connect to a VPN concentrator located outside of our network. We use PAT for address translation. As far as I know, to allow ipsec through Firewall 1 tunnel, I need to upgrade the pix to 6.3 and activate "fixup protocol esp-ike.

  Is there another way to do this? I am also curious to know how much more easy/better this will work if we were dealing with pptp.

  You don't necessarily need to fixup protocol esp-ike active. The remote Hub there encapsulation NAT - T enabled so that clients behind the NAT can run?

• Restrictions of VPN concentrator

  We use an all 3000 series concentrator some users access to a part of our network.

  It has been implemented to allow the PC to communicate with our private addresses (class B).

  I need access to a couple of IP internally (within the class B).

  Is it possible to refuse access to these IP specifically, or should I go and completely re - build the lists allow?

  To do this, the most consistent is to use filters and rules to deny traffic to these IP addresses, click on the following link for it:

  http://www.Cisco.com/en/us/docs/security/vpn3000/vpn3000_47/configuration/guide/polmgt.html

  Create rules and add them to a filter that can then be applied to the group that these clients are connecting to.

  On a different approach, if these vpn clients use the TunnelAll like politics of split tunnel, you can modify the policy to be "exclude the networks in the list in order to bypass the tunnel" and use a list system (which will contain the restricted hosts), and where the traffic is provided for guests, the VPN client will not tunnel traffic. FYI, this will send traffic for guests with this policy of TUNNEL from SPLIT to be sent the text, not routed, but sent in plain text by the vpn client.

• VPN concentrator 3000

  I have a small question, I have a backup ACS server which was built just now, I noticed on my hub under Config-online system-online servers = > authentication, I have the primary server for authentication in place, the question is do I add the server to backup ACS as well so if the primary goes it will automatically use the ACS server? Thank you in advance!

  This is how its supposed to work. Given that you have not set up a group of authentication servers list.

  Kind regards

  Prem

  Please rate if this can help!

• Ports open VPN concentrator

  I'm running the port scan (Angry IP Scanner) against VPN concentrator. Sometimes it shows the port as open 21. I have disabled ftp under "Management protocols" sometimes it shows the port 389 & 1002 as open. What wrong with my VPN concentrator?

  I activated only IPSEC protocol Tunneling.

  When I run the scan of port which ports are should be included amongst them open?

  Thank you

  Hello avilt,

  VCA means Cluster Virtual Agent. This is used mainly when the VPN 3000 pair is configured for load balancing,... when doing so cells communicate with each other on VCA and we must normally allow this on the filters...

  My question is, u have allowed this filter on the public interface? you see the ports via the VPN concentrator or you make a sweep WILL and see these ports (such as FTP) to be opened on the VPN concentrator?

  REDA