VPN routing issues...

Similar Questions

• Client VPN routing issue

  I am trying to configure client vpn software ver 5.0 for remote to connect to the local network behind a 1801 users.

  I can get the client saying its connected but traffic is not circulate outside in:

  When I try to ping an address 192.168.2.x behind the 1801 I get a response from the public ip address but then when I try to ping to another address I have no answer.

  I guess the question is associated with NAT.

  Here is my config, your help is apprecited

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  host name C#.

  !

  boot-start-marker

  boot-end-marker

  !

  enable password 7 #.

  !

  AAA new-model

  !

  AAA authentication login userauthen local

  AAA authorization groupauthor LAN

  !

  AAA - the id of the joint session

  !

  IP cef

  !

  IP domain name # .local

  property intellectual auth-proxy max-nodata-& 3

  property intellectual admission max-nodata-& 3

  !

  Authenticated MultiLink bundle-name Panel

  !

  username password admin privilege 15 7 #.

  !

  crypto ISAKMP policy 3

  BA 3des

  preshared authentication

  Group 2

  !

  ISAKMP crypto client configuration group 1801Client

  key ##############

  DNS 192.168.2.251

  win 192.168.2.251

  field # .local

  pool VpnPool

  ACL 121

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT

  !

  Crypto-map dynamic dynmap 10

  Set transform-set RIGHT

  !

  map clientmap client to authenticate crypto list userauthen

  card crypto clientmap isakmp authorization list groupauthor

  client configuration address map clientmap throwing crypto

  client configuration address map clientmap crypto answer

  10 ipsec-isakmp crypto map clientmap Dynamics dynmap

  !

  Archives

  The config log

  hidekeys

  !

  property intellectual ssh time 60

  property intellectual ssh authentication-2 retries

  !

  interface FastEthernet0

  address IP 87. #. #. # 255.255.255.252

  IP access-group 113 to

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  clientmap card crypto

  !

  interface BRI0

  no ip address

  encapsulation hdlc

  Shutdown

  !

  interface FastEthernet1

  interface FastEthernet8

  !

  ATM0 interface

  no ip address

  Shutdown

  No atm ilmi-keepalive

  DSL-automatic operation mode

  !

  interface Vlan1

  IP 192.168.2.245 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  !

  IP pool local VpnPool 192.168.3.200 192.168.3.210

  no ip forward-Protocol nd

  IP route 0.0.0.0 0.0.0.0 87. #. #. #

  !

  !

  no ip address of the http server

  no ip http secure server

  the IP nat inside source 1 interface FastEthernet0 overload list

  IP nat inside source static tcp 192.168.2.251 25 87. #. #. # 25 expandable

  Several similar to the threshold with different ports

  !

  access-list 1 permit 192.168.2.0 0.0.0.255

  access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq 22

  access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq 22

  access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq 22

  access-list 113 tcp refuse any any eq 22

  access-list 113 allow host tcp 82. #. #. # host 87. #. #. # eq telnet

  access-list 113 permit tcp 84. #. #. # 0.0.0.3 host 87. #. #. # eq telnet

  access-list 113 allow host tcp 79. #. #. # host 87. #. #. # eq telnet

  access-list 113 tcp refuse any any eq telnet

  113 ip access list allow a whole

  access-list 121 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

  access-list 121 allow ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255

  !

  control plan

  !

  Line con 0

  line to 0

  line vty 0 4

  transport input telnet ssh

  !

  end

  you have ruled out the IP address of the customer the NAT pool

  either denying them in access list 1

  or do road map that point to the loopback address as a next hop for any destent package for your pool to avoid nat

  first try to put this article in your access-lst 110

  access-list 110 deny 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255

  access-list 110 permit 192.168.2.0 0.0.0.255 any

  sheep allow 10 route map

  corresponds to the IP 110

  remove your old nat and type following one

  IP nat inside source overload map route interface fastethernet0 sheep

  rate if useful

  and let me know, good luck

• RVS4000 / WRVS4400 VPN routing issue.

  I would like to simplify my installation a bit, but unfortunately I do not know how to do this.

  I have a triangle of CSB RVS, 2 RVS4000, 1 WRVS4400 devices

  each router has a VPN gateway to gateway with 2 others, to any one of the 3 sites, you can access resources on the other 2.

  It also works well, if for some reason, one of the legs of the VPN breaks down, it passes through the other router.  at least it seems to work that way when it is tested.

  Now enter my problem.  I have 2 laptops that go around, Mine and at the office.  If any of these are off site and connect to a router via the QuickVPN client.  they can see the resources on the router, to which they connect.

  How would I be able to connect to the Router 1 and be able to access resources on other VPN routers ' ed?

  It is not so much a problem on the router because it is on the QuickVPN. When you go to an IP address that is not on the local network from the router, the QuickVPN does not and it that the request is sent to the internet.

  The only way to access the other site and resources would be to unplug the first router and connect to each other.

• Remote vpn routing issue

  Hi, please find the attachment.

  I want remote access client vpn server that connect you to my ASA 5510 outside interface.

  Is this possible via the static route set or something else?

  Thank you very much!!!

  Hello

  There is not enough information to give a good answer. This should be possible, but your level ASA software firewall and VPN Client configurations factor in this also.

  If you have a customer VPN Split Tunnel configuration, then you must add a rule to the existing ACL and say the IP address of the server. If you use Client VPN full Tunnel while you don't have to worry about the same thing only with Split Tunnel.

  Then you will probably need the configuration "permit same-security-traffic intra-interface" so that traffic can enter the 'outside' and leave 'outside' to the server. It won't work without the mentioned order.

  You will also need a PAT Dynamics example

  If you use a software 8.2 or below and have this dynamic PAT defect for LAN users

  Global 1 interface (outside)

  NAT (1 x.x.x.x y.y.y.y inside)

  Then for the Pool of Client VPN you can add this

  NAT (outside) 1 20.20.20.0 255.255.255.0

  More often, this should be sufficient to allow the traffic to arrive on the VPN Client user ASA and out of 'outside' interface and head to the server.

  Hope this helps

  Don't forget to mark the reply as the answer if it answered your question.

  -Jouni

• Tips to add a VPN router to my current network configuration

  Dear all

  My apologies if the answer to this question already exists, however, I searched in many situations and none seem to match what I'm after.

  I currently have an ISP modem/router in Bridge mode connected to a TC of Apple which is my wireless router, I have 2 Express airport connected to this acting as the extensors of the range.  I have a VPN service through the MyPrivate network I activate on the desired device when required and everything works fine.

  What I want to do now is to be able to use my AppleTV and burning Amazon via the VPN as well so you need to add a VPN router in the configuration.  I want to finish with 2 wireless networks running together for these devices who need VPN and those who are not.  I don't want to lose the opportunity to extend the network to express it however airport.

  If someone could explain to me if this is possible and if so how do I set up the network.

  Thanks in advance

  Mark

  Basically you would need a device that supports VPN-passthrough and VLANS for your goals of networking. MyPrivate network, seems to be a VPN SSL, which is a user-server configuration. In other words, you install a client VPN on your Mac and you connect to the VPN network MyPrivate server to establish a VPN tunnel.

  Networking two or more "separated", should be using a router that supports VLAN services. Each segment of VIRTUAL local area network, in essence, would be a separate, she either wired or wireless network or a combination of both. This would probably be the 'easiest' part for the installation program.

  Now how combining the two would be the question, and I don't know what would be the best way, or even if it is possible.

  A few thoughts:

  • Use a router that supports VLANS. Create at least two VIRTUAL LAN segments. One for Apple TV & Burns, one for Internet access in general. Connect the device to VPN client host on the first segment, and configure for Internet sharing.
  • Download a dedicated VPN network application that supports hosting of third-party VPN clients, like yours. You would still need a router that supports VLAN to provided separate network segments.
  • Hire a consultant network. Let them know what you the goals of networking and ask them to offer potential solutions.

• QuickVPN - could not do a ping the remote VPN router!

  Hello

  I have a RV042 (VPN router) and I have some problems to run properly using the QuickVPN client.

  Here is the Log of the QuickVPN client.

  2008-10-15 20:14:38 [STATUS] a network interface detected with 192.168.0.104 IP address
  2008-10-15 20:14:38 [STATUS] connection...
  2008-10-15 20:14:38 [STATUS] connection to a remote gateway with IP address: 96.20.174.84
  2008-10-15 20:14:38 [WARNING] server certificate does not exist on your local computer.
  2008-10-15 20:14:44 remote gateway [STATE] has been reached with https...
  2008-10-15 20:14:44 [STATUS] commissioning...
  2008-10-15 20:14:51 [STATUS] Tunnel is connected successfully.
  2008-10-15 20:14:51 [STATUS] verification of network...
  2008-10-15 20:14:55 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:14:58 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:01 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:05 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:08 [WARNING] failed to do a ping the remote VPN router!
  2008-10-15 20:15:11 [WARNING] Ping has been blocked, which can be caused by an unexpected disconnection.
  2008-10-15 20:15:19 [STATUS] disconnection...
  2008-10-15 20:15:25 [STATUS] Tunnel is disconnected successfully.

  I don't know how it is implemented, but if WuickVPN wait a form ping my router, it will not happen. I was never able to ping my router ouside of my ISP network.

  There is a way to disable the Ping process and continue with the VPN connection?

  QuickVPN try ping on the router via the VPN tunnel to check the connection. It should work without worrying about whether your ISP filters ICMP messages or not. The tunnel is encrypted your ISP won't know what you're doing.

  Please post the corresponding on the RV042 VPN log. That is expected to see how far you get.

  You have a firewall running on the computer? I think that some firewalls have difficulty with the traffic of ESP.

  What is the router that is connected to the computer? How is it that is configured?

• Remote access VPN routing

  Hello

  I'm having a problem on the VPN routing.

  The VPN client is connected correctly to ASA5510, but cannot access inside ASA and the Internet or another network. What I want to achieve is.

  [email protected] / * / -> ASA5520 (public IP)-> Inside (172.16.1.0)

  The VPN address pool uses 172.168.10.0 (I also tried 172.16.1.100 - 120 with the same network from the inside).

  interface GigabitEthernet0/0

  nameif outside

  security-level 0

  IP address a.a.a.a 255.255.255.0

  !

  interface GigabitEthernet0/1

  nameif inside

  security-level 100

  IP 172.16.1.1 255.255.255.0

  IP local pool vpnpool 192.168.10.1 - 192.168.10.254 mask 255.255.255.0

  access extensive list ip 172.16.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.10.0 255.255.255.0

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

  life crypto ipsec security association seconds 28800

  Crypto ipsec kilobytes of life - safety 4608000 association

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  internal VPNstaff group strategy

  attributes of Group Policy VPNstaff

  4.2.2.2 DNS server value

  Protocol-tunnel-VPN IPSec

  type tunnel-group VPNstaff remote access

  attributes global-tunnel-group VPNstaff

  address vpnpool pool

  Group Policy - by default-VPNstaff

  IPSec-attributes tunnel-group VPNstaff

  pre-shared-key *.

  Hello

  A quick test, try this.

  -Turn on nat - t (if its disable)

  Command: crypto isakmp nat-traversal 20

  see if it helps.

  If not,

  -Run a continuous ping from the client to the ASA inside the interface, make sure that you run the command 'management-access to inside' before you start with the ping.

  -Time our RESPONSE ICMP or inside the interface... ?

  If time-out, then

  -Check the number of decrypts using the command "show crypto ipsec his"

  If ICMP response to inside interface is received by the VPN client.

  -Ping to an internal host behind the ASA.

  -"Show crypto ipsec his"

  IF you have received responses if first test then here you should see decrypts number increases.

  -Apply the catches on the inside of the interface

  You can consult the document below

  http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a0080a9edd6.shtml

  -If you see the package source as VPN client interface to reach the inside interface for the destination of the host behind the ASA, then its a problem with your routing internal.

  In case you have an L3 device connected to the ASA inside the interface, make sure that you have a route for GW subnet 192.168.1.x as ASA inside the interface i.e. 172.16.1.1 score

  If his L2 or a dumb device, then as a quic test, make the following statement of the road using the command-line in windows on the host computer behind the asa participant in this test.

  route add 192.168.1.0 mask 255.255.255.0 172.16.1.1

  Please let me know if it helps.

  Concerning

  M

• Cisco IOS - access remote VPN - route unwanted problem

  Hello

  I recently ran into a problematic scenario: I am trying to connect to a remote LAN (using a Cisco VPN client on my windows xp machine) my office LAN and access a server there. The problem is that I need a remote local network access at the same time.

  Remote LAN: 172.16.0.0/16

  LAN office: 172.16.45.0/24

  Topology:

  (ME: 172.16.10.138/25) - (several subnets form 172.16.0.0/16) - (Internet cloud) - (VPN-Gateway) - (172.16.45.0/24) - (TARGET: 172.16.45.100)

  To provide access, I configured a VPN to access simple distance on a 1700 series router. It's the relevant part:

  (...)

  crypto ISAKMP client config group group-remote access

  my-key group

  VPN-address-pool

  ACL 100

  IP local pool pool of addresses-vpn - 172.16.55.1 172.16.55.30

  access-list 100 permit ip 172.16.45.100 host 172.16.55.0 0.0.0.31

  (...)

  The configuration works fine, I can access the 172.16.45.100 server every time I need to. However, the problem is that when the VPN connection is connected, Windows wants to somehow rout the packets intended for 172.16.0.0/16 through the VPN tunnel. This is apparently due to a static route that added by the Cisco VPN Client and all other specific VPN routes.

  I suspect that the culprit is the IP LOCAL POOL, since when the VPN is connected, debugging of Client VPN log shows something like "adapter connected, address 172.16.55.1/16. Focus on the part "/ 16". I checked the VPN status page and the only road indicated there was "172.16.45.100 255.255.255.255" under remote routes. Local routes was empty.

  Is this a known problem I missed the obvious solution for? Is there no workaround apart from the pool local vpn penetrating high-end 10.x.x.x or 192.168.x.x? Thank you in advance for advice or tips!

  Hello

  The best way is to avoid any overlap between the local network and VPN pool.

  Try 172.17.0.0/16, is also private IP address space:

  http://en.Wikipedia.org/wiki/Private_network

  Please rate if this helped.

  Kind regards

  Daniel

• Best Soho - Split Tunnel VPN router

  Hi - I'm looking for some advice for a soho router.

  Basically the main feature, I'm looking for is to run, which I think is a VPN split tunnel, so that all internal clients route default traffic out to the gateway of the ISP. However, if the traffic is destined for a list of several specific subnets (x.x.x.x/24, y.y.y.y/24 etc.), then it should establish a tunnel to an only PPTP/IPSEC host and route remote traffic for these subnets via the tunnel.   To be clear, that these subnets (x.x.x.x and y.y.y.y) is not attached to the end of the tunnel - which is a gateway device that will route them further.

  I've been watching the various VPN router offers and is not clear to me if I can do it with a RV - 042, BEFVP41 or something like the other thing SRP521W I must be able to manipulate the routing tables directly on.

  As an additional note, I have complete control over the end of SOHO - but simply an account at the end of the tunnel with (it is a service provider).  The idea is to use public services for 90% of the traffic, but if customers want to access a specific set of addresses, it will forward this specific traffic through the tunnel.

  Thanks in advance...

  On current view, do not touch the RPS with a bargepole.

  Adding access to additional subnets through a VPN tunnel is pretty standard, routing will be automatic if the VPN was established, but you must ensure that

  1. politics VPN at BOTH ENDS allows your local subnet to access these networks

  2. your subnet is not incompatible with other subnets or roads that can be used on remote networks

  3. assuming you're OK so far, remote subnets must have a route is added to the default gateway to point to your subnet via intermediate networks

  Good luck!

• VPN router to router with overlapping of internal networks

  Hello Experts,

  A small question. How to configure a VPN router to router with overlap in internal networks?

  Two of my internal networks have ip address 192.168.10.0 and 192.168.10.0

  No link or config will be appreciated. I searched but no luck.

  Thank you

  Randall

  Randall,

  Please see the below URL for the configuration details:

  Configure an IPSec Tunnel between routers with duplicate LAN subnets

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800b07ed.shtml

  Let me know if it helps.

  Kind regards

  Arul

  * Please note all useful messages *.

• Routing issue of Cisco VPN Client ASA

  Hi, I use a Barracuda NG for firewalls and I would use a Cisco ASA 5505 for VPN Client connections. But I have the problem that I can't get a connection to the VPN PC connected to the internal network. But I can reach the VPN connected PC from the inside. Here is a diagram of my network:

  cisco_asa_prob.jpg

  

  Here the IP Configuration and the routing of the Barracuda firewall table:

  screen_shot_2014-08 - 12_at_16.01.42.png

  

  I have a route on the Barracuda NG to the 10.10.10.0/24 network VPN Client on eth0.

  The 192.168.1.0/24 LAN I ping the Client comes with Client VPN 10.10.10.11 as it should. But I can't ping or access network resources in the local network for AnyConnected customer's PC that connected through the VPN.

  Here is the config Cisco ASA:

   : Saved : : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz : ASA Version 9.2(2) ! hostname leela names ip local pool VPN-Pool 10.10.10.10-10.10.10.200 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 switchport access vlan 5 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp ! interface Vlan5 nameif dmz security-level 50 ip address 172.16.0.250 255.255.255.0 ! ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server 192.168.1.10 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network obj_any subnet 0.0.0.0 0.0.0.0 object network VPN-Pool subnet 10.10.10.0 255.255.255.0 description VPN-Pool object network NETWORK_OBJ_10.10.10.0_24 subnet 10.10.10.0 255.255.255.0 access-list inside_access_in extended permit ip any any access-list inside_access_in extended permit ip object VPN-Pool any access-list dmz_access_in extended permit ip any any access-list global_access extended permit ip any any access-list outside_access_in extended permit ip any any pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected nat (inside,dmz) source static any any destination static NETWORK_OBJ_10.10.10.0_24 NETWORK_OBJ_10.10.10.0_24 no-proxy-arp route-lookup inactive access-group inside_access_in in interface inside access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz access-group global_access global route dmz 0.0.0.0 0.0.0.0 172.16.0.254 1 route inside 0.0.0.0 0.0.0.0 192.168.1.254 tunneled timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy server-type microsoft user-identity default-domain LOCAL aaa authentication enable console LDAP_SRV_GRP LOCAL aaa authentication http console LDAP_SRV_GRP LOCAL aaa authentication ssh console LDAP_SRV_GRP LOCAL aaa authentication serial console LOCAL http server enable 444 http 192.168.1.0 255.255.255.0 inside snmp-server location Vienna crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto map dmz_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map dmz_map interface dmz crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=leela proxy-ldc-issuer crl configure crypto ca trustpoint ASDM_TrustPoint1 enrollment terminal crl configure crypto ca trustpool policy crypto ca certificate chain ASDM_TrustPoint0 quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable dmz client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 no ssh stricthostkeycheck ssh 192.168.1.0 255.255.255.0 inside ssh timeout 30 ssh key-exchange group dh-group1-sha1 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.254-192.168.1.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept dynamic-filter updater-client enable dynamic-filter use-database ntp server 192.168.1.10 source inside ssl trust-point ASDM_TrustPoint0 dmz ssl trust-point ASDM_TrustPoint0 inside webvpn enable dmz no anyconnect-essentials anyconnect image disk0:/anyconnect-macosx-i386-3.1.05170-k9.pkg 1 anyconnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 2 anyconnect image disk0:/anyconnect-linux-3.1.05170-k9.pkg 3 anyconnect image disk0:/anyconnect-linux-64-3.1.05170-k9.pkg 4 anyconnect profiles AnyConnect_client_profile disk0:/AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy DfltGrpPolicy attributes default-domain value group-policy GroupPolicy_AnyConnect internal group-policy GroupPolicy_AnyConnect attributes wins-server none dns-server value 192.168.1.10 vpn-tunnel-protocol ikev2 ssl-client webvpn anyconnect profiles value AnyConnect_client_profile type user group-policy portal internal group-policy portal attributes vpn-tunnel-protocol ssl-clientless webvpn url-list none username tunnel-group AnyConnect type remote-access tunnel-group AnyConnect general-attributes address-pool VPN-Pool authentication-server-group LDAP_SRV_GRP default-group-policy GroupPolicy_AnyConnect tunnel-group AnyConnect webvpn-attributes group-alias AnyConnect enable tunnel-group Portal type remote-access tunnel-group Portal general-attributes authentication-server-group LDAP_SRV_GRP default-group-policy portal tunnel-group Portal webvpn-attributes group-alias portal enable! ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 ! prompt hostname context no call-home reporting anonymous hpm topN enable : end no asdm history enable

  Can someone please help me solve this problem?

  When I tried to solve this I didn't choose which interface the Packet Tracer?

  The interface inside or DMZ interface?  Inside, he says it will not work with the dmz but the error did not help me

  Anyone here knows why it does not work?

  screen_shot_2014-08 - 12_at_16.34.57.png

  

  screen_shot_2014-08 - 12_at_16.33.06.png

  

  Hello

  Inside LAN is directly connected to the right firewall VPN... then I don't think you have to have the itinerary tunnele... can you try to remove the road tunnel mode and check.

  entrance to the road that is static to achieve 10.10.10.11 as its display is correct...

  Route by tunnel watch also with 255 administrative distance.  I've never used that in my scenarios... lets see...

  Concerning

  Knockaert

• Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

  Hello

  Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

  The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

  Please, what missing am me?

  A few exits:

  ISAKMP crypto to show her:

  isakmp crypto #show her

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  Crypto ipsec to show her:

  Interface: GigabitEthernet0/0

  Tag crypto map: QRIOSMAP, local addr 62.173.32.122

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

  current_peer 62.173.32.50 port 500

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  #pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0

  #pkts not unpacked: 0, #pkts decompress failed: 0

  Errors #send 0, #recv 0 errors

  local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

  Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

  current outbound SPI: 0x4D7E4817 (1300121623)

  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:

  SPI: 0xEACF9A (15388570)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

  calendar of his: service life remaining (k/s) key: (4491222/1015)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  Please see my config:

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  encryption... isakmp key address 62.X.X... 50

  ISAKMP crypto keepalive 10 periodicals

  !

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

  !

  QRIOSMAP 10 ipsec-isakmp crypto map

  peer 62.X.X set... 50

  transformation-TS-QRIOS game

  PFS group2 Set

  match address 100

  !

  !

  !

  !

  !

  interface GigabitEthernet0/0

  Description WAN CONNECTION

  62.X.X IP... 124 255.255.255.248 secondary

  62.X.X IP... 123 255.255.255.248 secondary

  62.X.X IP... 122 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  card crypto QRIOSMAP

  !

  interface GigabitEthernet0/0.2

  !

  interface GigabitEthernet0/1

  LAN CONNECTION description $ES_LAN$

  address 192.168.20.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  !

  IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

  IP nat inside source list 1 pool mypool overload

  overload of IP nat inside source list 100 interface GigabitEthernet0/0

  !

  access-list 1 permit 192.168.20.0 0.0.0.255

  access-list 2 allow 10.2.0.0 0.0.0.255

  Note access-list 100 category QRIOSVPNTRAFFIC = 4

  Note access-list 100 IPSec rule

  access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

  access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

  access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

  access-list 101 deny ip any any newspaper

  access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 110 permit ip 192.168.20.0 0.0.0.255 any

  !

  !

  !

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

  Here are the things I see in your config

  I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

  IP route 0.0.0.0 0.0.0.0 62.X.X... 121

  IP route 0.0.0.0 0.0.0.0 62.172.32.121

  This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

  IP route 10.2.0.0 255.255.255.0 192.168.20.2

  In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

  IP route 172.17.0.0 255.255.0.0 Tunnel20

  IP route 172.17.2.0 255.255.255.0 Tunnel20

  And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

  IP route 172.18.0.0 255.255.0.0 Tunnel20

  IP route 172.18.0.0 Tunnel20 255.255.255.252

  HTH

  Rick

• Routing issue to site VPN site

  Hello

  I have a VPN site-to site of SR520 at SFsence VPN, the tunnel is up, but I can't ping internal addresses of these two paths of layout of the site terminate my default gateway. Help, please

  Access list configuration:

  access-list 100 permit ip 10.0.43.0 0.0.0.255 10.10.10.0 0.0.0.255

  access-list 100 permit ip 10.10.10.0 0.0.0.255 10.0.43.0 0.0.0.255

  IP nat inside source map route SHEEP interface Dialer 0 overload

  access-list 110 deny ip 10.10.10.0 0.0.0.255 10.0.43.0 0.0.0.255

  access-list 110 permit ip 10.10.10.0 0.0.0.255 any

  SHEEP allowed 10 route map

  corresponds to the IP 110

  Note: remote site (SFsence) of 10.0.43.0/24

  local site router Cisco SR520 10.10.10.0/29

  Glad to know everything works now,

  Please check the question as answered so future users can learn on this basis.

  Kind regards

• Routing issue after establish VPN

  Hello

  I have configure VPDN on router cisco very well, I can dila fine external windows vpn client vpn. but o cannot access all the servers behind my router. I can ping internal IP address of the router (10.2.1.1) only.

  I have two subnet 10.1.1.0 and 10.2.1.0 I need to get access via VPN

  Current configuration: 6253 bytes
  !
  version 12.4
  no service button
  tcp KeepAlive-component snap-in service
  a tcp-KeepAlive-quick service
  horodateurs service debug datetime localtime show-timezone msec
  Log service timestamps datetime localtime show-timezone msec
  encryption password service
  sequence numbers service
  !
  hostname wrmelgw
  !
  boot-start-marker
  boot-end-marker
  !
  logging buffered 51200
  recording console critical
  enable secret 5 *.
  !
  No aaa new-model
  clock timezone PCTime 10
  PCTime of summer time clock day March 30, 2003 03:00 October 26, 2003 02:00
  !
  Crypto pki trustpoint TP-self-signed-860329787
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 860329787
  revocation checking no
  rsakeypair TP-self-signed-860329787
  !
  !
  TP-self-signed-860329787 crypto pki certificate chain
  certificate self-signed 01
  308201B 5 A0030201 02020101 3082024C 300 D 0609 2A 864886 F70D0101 04050030
  2 060355 04031325 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 30312E30
  69666963 38363033 32393738 37301E17 313031 31313130 32313934 0D 6174652D
  345A170D 2E302C06 1325494F 03550403 32303031 30313030 30303030 5A 303031
  532D 5365 6C662D53 69676E65 4365 72746966 69636174 652 3836 30333239 642D
  06092A 86 4886F70D 01010105 37383730 819F300D 00308189 02818100 0003818D
  B48727D9 C6678610 CF7A69F6 BFFE48F2 63EE0A8D BFD7B83A 50659F84 FF358CA5
  5AD0ED97 B7D8212F E99AB991 36D0B172 538D D68B8746 51650BAC 17256811 1639
  80AB4344 B40FCDD1 B64B7011 49F90515 E2AD7346 4B1F1E5D 20F7D5F5 6B0AC5A8
  CF 255 444 1C29392E 634F9611 CF5761ED B873C63F 95B04B0D 38760A1B F6A5667B
  02030100 01A 37630 03551 D 13 74300F06 0101FF04 05300301 01FF3021 0603551D
  11041A 30 726D656C 18821677 67772E79 6F757264 6F6D6169 6E2E636F 6D301F06
  03551 D 23 80145FE0 04183016 D5554371 95D2A995 956BBCB2 0686 C 313 A06B301D
  0603551D 0E041604 145FE0D5 D2A99595 55437195 6BBCB206 86C313A0 6B300D06
  092A 8648 01040500 03818100 245311 1 A9BBA0F4 66D3A9BA 6D8AF2FD 86F70D01
  45785 D 42 3496AF0B B5513CDE 3B3CBFB3 D258E2F9 581442 3 A73E063F E9B071E5
  21E5CF80 FA0D717F 8A6F5202 BB88C26C A6D3A559 BA520562 CA 9 08447 0DB28B33
  5BBDC1D4 86EA654F 3AFEA64D 8BA13738 14952C7A 0FB76D7A 2B47883A 27DCB43B
  7DA80B53 8D98010E A 451, 2949 CBCE63A7
  quit smoking
  dot11 syslog
  no ip source route
  IP cef
  DHCP excluded-address IP 10.2.1.1 10.2.1.99
  !
  !
  no ip bootp Server
  "yourdomain.com" of the IP domain name
  name of the IP-server 139.130.4.4
  name of the IP-server 203.50.2.71
  !
  VPDN enable
  !
  VPDN-Group 1
  ! PPTP by default VPDN group
  accept-dialin
  Pptp Protocol
  virtual-model 1
  !
  !
  !
  username * privilege 15 secret *.
  vpn username password *.
  !
  !
  crypto ISAKMP policy 1
  BA 3des
  md5 hash
  preshared authentication
  QnrpzdFI crypto isakmp key address *.
  ISAKMP crypto 5 30 keepalive
  !
  !
  Crypto ipsec transform-set esp-3des esp-md5-hmac vpn - ts
  !
  RTP 1 ipsec-isakmp crypto map
  set peer *.
  the value of the transform-set vpn - ts
  match the address sydLAN
  !
  Archives
  The config log
  hidekeys
  !
  !
  synwait-time of tcp IP 10
  property intellectual ssh time 60
  property intellectual ssh authentication-2 retries
  !
  !
  !
  ATM0 interface
  no ip address
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  route IP cache flow
  No atm ilmi-keepalive
  DSL-automatic operation mode
  !
  point-to-point interface ATM0.1
  Description $FW_OUTSIDE$ $ES_WAN$
  PVC 8/35
  aal5mux encapsulation ppp Dialer
  Dialer pool-member 1
  !
  !
  interface FastEthernet0
  !
  interface FastEthernet1
  Inside description
  switchport access vlan 100
  !
  interface FastEthernet2
  !
  interface FastEthernet3
  !
  interface virtual-Template1
  IP unnumbered Vlan1
  peer default ip address pool vpn
  No keepalive
  PPP mppe auto encryption required
  PPP ms-chap for authentication ms-chap-v2
  !
  interface Vlan1
  Data VLAN description
  10.2.1.1 IP address 255.255.255.0
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly
  route IP cache flow
  IP tcp adjust-mss 1452
  !
  interface Vlan100
  Description VLAN VoIP
  no ip address
  !
  interface Dialer0
  203.* IP address. *. * 255.255.255.0
  IP access-group dry in
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly
  encapsulation ppp
  route IP cache flow
  Dialer pool 1
  Dialer-Group 1
  No cdp enable
  Authentication callin PPP chap Protocol
  PPP chap hostname *

  PPP chap password 7 *.
  crypto rtp map
  !
  VPN IP local pool 10.2.1.70 10.2.1.85
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 203.45.89.1
  IP route 10.1.0.0 255.255.0.0 10.2.1.254
  !
  no ip address of the http server
  local IP http authentication
  no ip http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  IP nat inside source static tcp 10.2.2.201 80 Dialer0 8001 interface
  IP nat inside source static tcp 10.2.2.200 80 Dialer0 8008 interface
  IP nat inside source map route VPN-sheep interface Dialer0 overload
  IP nat inside source static tcp 10.2.2.200 8000 203.45.89.182 8000 extensible
  !
  SHEEP extended IP access list
  deny ip 10.0.0.0 0.255.255.255 10.0.0.0 0.255.255.255
  IP 10.2.1.0 allow 0.0.0.255 any
  ip licensing 10.2.2.0 0.0.0.255 any
  dry extended IP access list
  permit tcp any any eq 1723
  allow icmp a whole
  allow tcp any a Workbench
  permit any any icmp echo response
  permit any any icmp echo
  allow icmp all once exceed
  ICMP all all ttl-exceeded allow it
  allow all all unreachable icmp
  permit tcp any any eq 22
  allow an esp
  permit any any eq non500-isakmp udp
  allow udp any any eq isakmp
  allow a gre
  allow a whole ahp
  allow any host 203.45.89.182 eq 8000 tcp
  permit tcp any host 203.45.89.182 eq 8001
  allow any host 203.45.89.182 eq 8008 tcp
  deny ip any any newspaper
  sydLAN extended IP access list
  IP 10.2.0.0 allow 0.0.255.255 10.1.0.0 0.0.255.255
  !
  recording of debug trap
  Dialer-list 1 ip protocol allow
  not run cdp
  !
  !
  route map VPN-sheep permit 1
  corresponds to the IP SHEEP
  !
  !
  control plan
  !
  connection of the banner ^ CAuthorized access only!
  Unplug IMMEDIATELY if you are not an authorized user. ^ C
  !
  Line con 0
  local connection
  no activation of the modem
  telnet output transport
  line to 0
  local connection
  telnet output transport
  line vty 0 4
  privilege level 15
  local connection
  transport input telnet ssh
  !
  max-task-time 5000 Planner
  Scheduler allocate 4000 1000
  Scheduler interval 500
  end

  You want to reach10.1.1.0 and 10.2.1.0

  The router has this route:
  IP route 10.1.0.0 255.255.0.0 10.2.1.254
  and this interface:
  interface Vlan1
  10.2.1.1 IP address 255.255.255.0

  This means that so that the VPN client reach 10.1.0.0/24, you need a route from the pool of VPN on the device 10.2.1.254 (guess another router).

  Also, please make sure that you have made the changes the ACL in my first post.

  I'm not sure I understand this: "

  just let you know that 10.2.1.0 is the direct network and there is between 10.2.1.0 and 10.1.1.0 ipsec tunnel (perhaps help) "

  So far I see 10.1.1.0 is accessible through 10.2.1.254, if you need a route to the router to reach the VPN pool.

  Example of route on 10.2.1.254:

  IP 10.2.1.x MASK 10.2.1.1--> road road to join the VPN pool inside the router IP

  Federico.

• WRVS4400N VPN Passthrough issues

  I had a WRVS4400N router for 8-9 months. When it is connected to a remote VPN, the PC will go down intermittently to connect to the remote VPN server. Anything running on the connection, such as distance or vSphere client or network file browsing, office will be temporarily unusable, then the connection is re-established. Usually one drop lasts several seconds and varies in frequency.

  A few notes:

  -I can reproduce the problem with more than one PC.

  -Both wired and wireless connections are affected.

  -If I use an old Linksys WRT router or connect directly to the internet modem, I don't see the problem.

  -J' have tried disabling UPnP, firewall and IPS without success.

  I tried using wireshark, but can't identify something specific. The traffic seems to just stop for 5-10 seconds before resuming.

  Any suggestions/help would be appreciated.

  Mr Champion,

  
  

  Have you tried just the quickvpn client and the view if your always get disconnected?

  
  

  If it is stable and pull-out decision still does not work, maybe try to download a fresh firmware of cisco.com, then reflash the router with firmware then reset factory of the router and manually reconfigure your settings and see if your seeing the same issue.

  
  

  I would like to know how it works.