VPN tunnel between 2 ASA 5505 with the same default gateway

Similar Questions

• Site to Site VPN tunnel between two ASA

  I use the Site Wizard to Site on an ASA 5520, and ASA 5505 of the ADSM. Both are using 8.4 (5). When you create configurations. You follow the wizard configurations with manual what ACL s to allow the traffic of every subnet connected to talk to each other? Or they are automatically generated in the configuration file? Have not been to school yet to understand how to create the CLI VPN tunnels and what to look for.

  Thank you

  Carlos

  Hello

  First, I would like to say that I don't personally use ASDM for the configuration.

  But you should be able to configure all the necessary elements for a connection VPN L2L base through the wizard.

  I guess that typical problems to do so could relate to the lack of configuration NAT exempt or might not choose the setting "Bypass Interface Access List" that would mean you would allow traffic from the remote site in the 'external' ACL of ASA local interface. Like all other traffic coming from behind the 'outer' interface

  If you share format CLI configurations and say what networks must be able to connect via VPN L2L then I could give the required CLI format configurations.

  -Jouni

• EzVPN between Cisco ASA 5505 (with NEM mode) and Ciscoo 881 Roure

  Hi friends,

  I configured the Cisco ASA 5505 and Cisco router with DMVPN 881. 3 offices works very well but one office remains failure. I did the same configuration for all facilities but this router does not work. Any ideas?

  Please find below the exit of 881 router Cisco:

  YF2_Tbilisi_router #.
  * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:26.793 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:31:26.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:26.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:36.793 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
  * 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:31:36.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:36.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 09:31:44.929 4 August: ISAKMP: (0): serving SA., its is 88961 B 34, delme is 88961 B 34
  * 4 August 09:31:46.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:46.793 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:31:46.793 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
  * 4 August 09:31:46.793: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
  * 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:31:46.793 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
  * 09:31:46.793 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
  * 09:31:46.793 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 09:31:46.793 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

  * 4 August 09:31:47.805: del_node 2.2.2.2 src dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
  * 09:31:47.805 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 4 August 09:31:47.805: ISAKMP: (0): profile of THE request is (NULL)
  * 09:31:47.805 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
  * 09:31:47.805 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004819
  * 09:31:47.805 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
  * 09:31:47.805 4 August: ISAKMP: (0): client configuration parameters 87531228 adjustment
  * 09:31:47.805 4 August: ISAKMP: 500 local port, remote port 500
  * 09:31:47.805 4 August: ISAKMP: find a dup her to the tree during his B 88961, 34 = isadb_insert call BVA
  * 4 August 09:31:47.805: ISAKMP: (0): set up client mode.
  * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
  * 4 August 09:31:47.805: ISAKMP: (0): built the seller-07 ID NAT - t
  * 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-03 ID
  * 4 August 09:31:47.805: ISAKMP: (0): built the seller-02 ID NAT - t
  * 4 August 09:31:47.805: ISKAMP: more send buffer from 1024 to 3072
  * 09:31:47.805 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
  * 09:31:47.805 4 August: ISAKMP (0): payload ID
  next payload: 13
  type: 11
  Group ID: Youth_Facility_2
  Protocol: 17
  Port: 0
  Length: 24
  * 09:31:47.805 4 August: ISAKMP: (0): the total payload length: 24
  * 09:31:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
  * 09:31:47.809 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

  * 4 August 09:31:47.809: ISAKMP: (0): Beginner aggressive Mode Exchange
  * 4 August 09:31:47.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:47.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:31:57.809 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
  * 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:31:57.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:31:57.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:07.809 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
  * 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:07.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:07.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:17.809 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
  * 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:17.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:17.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:27.809 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:27.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:27.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:37.809 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
  * 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:37.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:37.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 09:32:46.793 4 August: ISAKMP: (0): serving SA., his is 872E1504, delme is 872E1504
  * 4 August 09:32:47.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:47.809 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:32:47.809 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
  * 4 August 09:32:47.809: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
  * 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
  * 09:32:47.809 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
  * 09:32:47.809 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
  * 09:32:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 09:32:47.809 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

  * 4 August 09:32:48.909: del_node src 2.2.2.2:500 dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
  * 09:32:48.909 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 4 August 09:32:48.909: ISAKMP: (0): profile of THE request is (NULL)
  * 09:32:48.909 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
  * 09:32:48.909 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004818
  * 09:32:48.909 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
  * 09:32:48.909 4 August: ISAKMP: (0): client setting Configuration parameters 88C05A48
  * 09:32:48.909 4 August: ISAKMP: 500 local port, remote port 500
  * 09:32:48.909 4 August: ISAKMP: find a dup her to the tree during the isadb_insert his 87B57D38 = call BVA
  * 4 August 09:32:48.909: ISAKMP: (0): set up client mode.
  * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
  * 4 August 09:32:48.909: ISAKMP: (0): built the seller-07 ID NAT - t
  * 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-03 ID
  * 4 August 09:32:48.909: ISAKMP: (0): built the seller-02 ID NAT - t
  * 4 August 09:32:48.909: ISKAMP: more send buffer from 1024 to 3072
  * 09:32:48.913 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
  * 09:32:48.913 4 August: ISAKMP (0): payload ID
  next payload: 13
  type: 11
  Group ID: Youth_Facility_2
  Protocol: 17
  Port: 0
  Length: 24
  * 09:32:48.913 4 August: ISAKMP: (0): the total payload length: 24
  * 09:32:48.913 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
  * 09:32:48.913 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

  * 4 August 09:32:48.913: ISAKMP: (0): Beginner aggressive Mode Exchange
  * 4 August 09:32:48.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:48.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:32:58.913 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
  * 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:32:58.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:32:58.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:33:08.913 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
  * 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:33:08.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:33:08.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:33:18.913 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
  * 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:33:18.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:33:18.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
  * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
  * 09:33:28.913 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
  * 4 August 09:33:28.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
  * 09:33:28.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.

  There is no DMVPN on the SAA. All that you have configured, is not compatible with the ASA or something another DMVPN then. At least debugging shows that there are some EzVPN involved.

  The debug version, it seems that there is no communication on UDP/500 possible between devices. Maybe something is blocking who?

• Why should Windows 8.1 I 2 different profiles with the same default folders, but each with completely different content?

  I want to save my e-mail and archives. I intend to put them in my folder "Documents" for backup of 'Cloud' and also in an external hard drive that I have always used in the past and, as a child of 76 with a new computer, 8.1 instead of XP and TB instead of Outlook Express, that I feel more confident on my external hard drive! I have 31 TB and Windows 8.1. I put my computer to show the "hidden files and folders". In user/AppData/Local name there is a record of TB with 'Profiles' and there my XXXX.default folder - but it has only a limited number of files and folders (Cache/cache2...). In user/AppData/Roaming name, there is also a TB with 'Profiles' folder and there my XXXX.default folder- but it contains a completely different and much larger files and Folders collection (4 different folders and multiple files MAB and SQLITE and others). Why have I not two files with different content identical default? Do I have to register each one? Can someone please explain/help, preferably in words this 76 year-old could understand.

  Windows 8 user accounts can be local or remote. It assumes that everyone has a roaming profile. Thunderbird uses mobile records as you can see, but there is only the rump in local that I don't really understand the existence of.

  Thunderbird does not use it, I guess that windows creates.

• My image file thumbnails appear with the same default image of a river and two mountains, why?

  You turn on your computer, open my computer, a drive and a folder where you store images. There are a lot of pictures. You want to copy a picture. But you can't just select it. Because all thumbnails are "same." You will need to open each photo to chech them.

  Yes, it's what is the problem that I am facing my pc. It's a Windows Vista Starter SP2. Everything was fine, but I don't know since when this started to happen.

  A solution please.

  Concerning

  Shashidhar

  Here's a possibility... go to... Start ORB / Control Panel.
  Folder options / tab / files and folders / uncheck
  "Always show icons, never thumbnails" / apply / OK.

• Problem with Tunnel VPN L2L between 2 ASA´s

  Hi guys,.

  I have some problems with my VPN Site to site tunnel between 2 ASA (5520/5505).

  I watched a lot of videos on youtube, but I can't find out why the tunnel does not...

  Both devices can ping eachothers WAN IP address (outside interfaces), but I don't see any traffic between the 2 sites. It seems that the tunnel is not open to everyone. When i PING from the local to the Remote LAN (which should be an interesting traffic for the tunnel...), the its IKEv1 remains empty...

  Am I missing something? I can't understand it more why same phase 1 is not engaged.

  You NAT won't. In your config file traffic is NATted initially and then does not match any more crypto ACL. You must move the rule dynamic NAT/PAT until the end of the table on two ASAs NAT:

   no nat (INSIDE,OUTSIDE) source dynamic any interface nat (INSIDE,OUTSIDE) after-auto source dynamic any interface

• Help with a VPN tunnel between ASA 5510 and Juniper SSG20

  Hello

  We have a customer wanting to configure a VPN Site to Site tunnel between a new purchased 5510 of ASA located in his direction with its Juniper SSG20 Office, located in the main office. We contacted HP and they send us a Cisco professional to do the job.

  After 2 days from 16:00 to 22:00 and error and countless hours of research online and nunerous calls, we are still unable to get traffic from the network of agencies to enter the tunnel.

  Main branch
  1.1.1.2                                 1.1.1.1
  -----                                               -----------
  192.168.8.0/24 | ASA|-----------------------------------| Juniper |    192.168.1.0/24
  -----                                               -----------
  192.168.8.254 192.168.1.254

  According to Cisco professionals, the tunnel is now in place but no traffic through. We are unable to ping anything on the network on the other side (192.168.1.0/24). We receive timeout ping all the time. The Cisco professional told us it's a routing or NAT problem and he's working on a solution!

  Through research, I came across a post on Experts-Exchange (here) [the 1st comment on the original post] which States "...". that both sides of the VPN must have a different class of LAN for the VPN to work... " Would that be our problem?

  It has become a critical issue to the point that he had to replace the Cisco ASA with a temporary Juniper SSG5 on another subnet (192.168.7.0/24) to get the tunnel upward and through traffic until the ASA VPN issue is resolved and I didn't need to say that the client is killing us!

  Help is very appreciated.

  Thank you

  1. Yes, ping package from the interface of the ASA is considered valuable traffic to the LAN of Juniper.

  SAA, need you traffic from the interface source ASA's private, because interesting to determine by crypto ACL MYLIST traffic between 192.168.8.0/24 and 192.168.1.0/24.

  You will also need to add the following configuration to be able to get the ping of the interface of the ASA:

  management-private access

  To initiate the ping of the private interface ASA:

  ping 192.168.1.254 private

  2. the default time before the next generation of new key is normally 28800 seconds, and if there is no interesting traffic flowing between 2 subnets, he'll tear the VPN tunnel down. As soon as there is interesting traffic, the VPN tunnel will be built automatically into the next generation of new key. However, if there is traffic before generating a new key, the new tunnel will be established, and VPN tunnel will remain standing and continue encrypt and decrypt traffic.

  Currently, your configuration has been defined with ITS lifetime of 3600 seconds GOLD / 4608000 kilobytes of traffic before the next generate a new key (it will be either 3600 seconds, or 4608000 kilobytes period expires first). You can certainly change it by default to 28800 seconds without configuring kilobytes. SA life is negotiated between the ASA and Juniper, and whatever is the lowest value will be used.

  Hope that helps.

• ASA 5505 - I can't create an IPSEC VPN between two ASA 5505

  Hello

  I have two ASA 5505 with basic license and I'm trying to create a VPN IPSEC using the CLI. Here are the steps I did:

  1 Configure ASA-1 (host name, vlan 1 and vlan 2).

  2. configure a static route

  3. create object network (local and remote)

  4. create the access list

  5. create ikev1 crypto

  6. create tunnel-group

  7 Configure nat

  and I repeat the steps above with the ASA but another change IP.

  Are to correct the above steps?

  Why can I not create an IPSEC VPN between devices?.

  No, you needn't. The ASA configuration is ok. Packet trace proved it. I think it can be a problem on the hosts. Please, check the firewall on the PC and try to put out of service, if it is running.

• L2l between an ASA 5505 and WatchGuard XTM330 with dynamic IP

  Hi guys,.

  I looked for a solution on this one but can't find inappropriate, most of the discussions were old and with dead links to the solution.

  We have an ASA 5505 with static IP address on the outside and a customer who have a WatchGuard XTM330 with dynamic IP address to the outside.

  Is it possible to have an L2L VPN between our ASA and the WatchGuard when he has a dynamic IP?

  I have no experience on the series of WatchGuard,

  so, I am very grateful for any answer!

  Thanks in advance and have a nice day

  BR

  Robin

  Hi Robin,

  Here are the links you can make reference when configuring static to the dynamic VPN tunnel: -.
  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-next-generation-firewalls/112075-dynamic-IPSec-ASA-router-CCP.html

  This one is with Pix on the remote side, but the configuration will remain the same on the local side: -.
  http://www.WatchGuard.com/docs/4-6-Firebox-CiscoPix.PDF

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Two VPN tunnels on the same device with the same protected networks

  There is a remote site that wants me to put in place two separate tunnels of VPN with the same internal IP at each end. FOR EXAMPLE

  LAN = 10.212.170.201/32, 10.212.170.202/32

  Remote network 192.168.0.0/24 =

  I currently have a tunnel between the above:

  End Point distance = 111.93.152.186

  Local endpoint point = 198.205.115.252

  Now, they want to set up a VPN for the same networks between:

  End Point distance = 115.115.130.34

  Local endpoint point = 198.205.115.252

  It is my understanding that the Cisco ASA 5520 can do. The only way I've seen this done with Cisco hardware is to use two ASAs, but there may be a way to use the costs of road or some other tricks to make it happen.

  I'm open to suggestions.

  Is a backup?

  In, specify endpoint remote second as a "backup" of the peer in the first virtual private network.  Alone will be active at the time - but there are toggled if the VPN in first dies.

• Site to Site VPN between Cisco ASA 5505 and Sonicwall TZ170

  I'm trying to implement a VPN site-to site between our data center and office.  The data center has a Cisco ASA 5505 and the Office has a Sonicwall TZ170.  I managed to configure the two so that the vpn connects.  Each of the firewall I ping the IP Address of the internet firewall on the other side and a desktop computer I can ping the IP Address of the firewall internal datacenter but I can't carry traffic between private subnets datacenter and desktop.  Can anyone help?

  The config below has had IPs/passwords has changed.

  External Datacenter: 1.1.1.4

  External office: 1.1.1.1

  Internal data center: 10.5.0.1/24

  Internal office: 10.10.0.1/24

  : Saved
  :
  ASA Version 8.2 (1)
  !
  hostname datacenterfirewall
  mydomain.tld domain name
  activate the password encrypted
  passwd encrypted
  names of
  name 10.10.0.0 OfficeNetwork
  10.5.0.0 DatacenterNetwork name
  !
  interface Vlan1
  nameif inside
  security-level 100
  10.5.0.1 IP address 255.255.255.0
  !
  interface Vlan2
  nameif outside
  security-level 0
  1.1.1.4 IP address 255.255.255.0
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  passive FTP mode
  clock timezone IS - 5
  clock to summer time EDT recurring
  DNS server-group DefaultDNS
  buydomains.com domain name
  permit same-security-traffic inter-interface
  permit same-security-traffic intra-interface
  inside_access_in list extended access permit icmp any one
  inside_access_in list extended access permitted tcp a whole
  inside_access_in list extended access udp allowed a whole
  inside_access_in of access allowed any ip an extended list
  outside_access_in list extended access permit icmp any one
  outside_access_in list extended access udp allowed any any eq isakmp
  IP DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0 allow Access-list extended pixtosw
  pixtosw list extended access allow icmp DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0
  IP OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0 allow Access-list extended pixtosw
  pixtosw list extended access allow icmp OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0
  outside_cryptomap_66.1 list of allowed ip extended access all OfficeNetwork 255.255.255.0
  outside_cryptomap_66.1 ip OfficeNetwork 255.255.255.0 allowed extended access list all
  outside_cryptomap_66.1 list extended access permit icmp any OfficeNetwork 255.255.255.0
  outside_cryptomap_66.1 list extended access allowed icmp OfficeNetwork 255.255.255.0 everything
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  IP verify reverse path to the outside interface
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 623.bin
  don't allow no asdm history
  ARP timeout 14400
  NAT-control
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0
  inside_access_in access to the interface inside group
  Access-group outside_access_in in interface outside
  Route inside 0.0.0.0 0.0.0.0 1.1.1.1 1
  Route OfficeNetwork 255.255.255.0 outside 1.1.1.1 1
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  dynamic-access-policy-registration DfltAccessPolicy
  Enable http server
  http 10.5.0.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set esp-aes-256 walthamoffice, esp-sha-hmac
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto dynamic-map ciscopix 1 corresponds to the address outside_cryptomap_66.1
  Crypto dynamic-map ciscopix 1 transform-set walthamoffice
  Crypto dynamic-map ciscopix 1 the value reverse-road
  map dynmaptosw 66-isakmp ipsec crypto dynamic ciscopix
  dynmaptosw interface card crypto outside
  crypto isakmp identity address
  crypto ISAKMP allow outside
  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  crypto ISAKMP policy 13
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  lifetime 28800
  crypto ISAKMP policy 30
  preshared authentication
  aes-256 encryption
  sha hash
  Group 2
  life 86400
  No encryption isakmp nat-traversal
  Telnet 10.5.0.0 255.255.255.0 inside
  Telnet timeout 5
  SSH 10.5.0.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  management-access inside
  dhcpd address 10.5.0.2 - 10.5.0.254 inside
  dhcpd allow inside
  !

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  NTP server 66.250.45.2 source outdoors
  NTP server 72.18.205.157 source outdoors
  NTP server 208.53.158.34 source outdoors
  WebVPN
  attributes of Group Policy DfltGrpPolicy
  VPN-idle-timeout no
  username admin password encrypted
  tunnel-group 1.1.1.1 type ipsec-l2l
  tunnel-group 1.1.1.1 ipsec-attributes
  pre-shared-key *.
  !
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  !
  context of prompt hostname
  Cryptochecksum:7f319172e5de9c0e550804a263f8e49e
  : end

  Mattew, obvious lack of education is the rule exempt from nat for your tunnel, your access list pixtosw is similar on this example, I assume that you have gone through this link, if it does not see the configs on both sides.

  Add the statement of rule sheep in asa and try again.

  NAT (inside) 0-list of access pixtosw

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008052c9d4.shtml

  Concerning

• VPN tunnel between the concentrator 3005 and router Cisco 827

  I am trying to establish a VPN tunnel between the Central Office with VPN 3005 and controller branch Cisco 827 router.

  There is a router of perimeter with access set up in front of the 3005 list.

  I quote the ACLs on the Central perimeter router instructionsuivante to allow traffic to permit ip 3005 - acl 101 all 193.188.X.X (address of the hub)

  I get the following message appears when I try to ping a local host in the Central site.

  Can Anyoune give me the correct steps to 827 and 3005.

  Thank you

  CCNP Ansar.

  ------------------------------------------------------------------------------------------------------

  Debug crypto ISAKMP

  encryption of debugging engine

  Debug crypto his

  debug output

  ------------------

  1d20h: IPSEC (sa_request):,.

  (Eng. msg key.) Local OUTGOING = 172.22.113.41, distance = 193.188.108.165.

  local_proxy = 202.71.244.160/255.255.255.240/0/0 (type = 4),

  remote_proxy = 128.128.1.78/255.255.255.255/0/0 (type = 1),

  Protocol = ESP, transform = esp - esp-md5-hmac.

  lifedur = 3600 s and KB 4608000,

  SPI = 0x83B8AC1B (2209917979), id_conn = 0, keysize = 0, flags = 0x400D

  1d20h: ISAKMP: ke received message (1/1)

  1d20h: ISAKMP: 500 local port, remote port 500

  1d20h: ISAKMP (0:1): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM

  Former State = new State IKE_READY = IKE_I_MM1

  1d20h: ISAKMP (0:1): early changes of Main Mode

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE...

  1d20h: ISAKMP (0:1): will increment the error counter on his: retransmit the phase 1

  1d20h: ISAKMP (0:1): retransmission phase 1 MM_NO_STATE

  1d20h: ISAKMP (0:1): lot of 193.188.108.165 sending (I) MM_NO_STATE

  1d20h: IPSEC (key_engine): request timer shot: count = 1,.

  You must also allow the esp Protocol in your ACL.

  access-list 101 permit esp any host x.x.x.x (address of the hub)

  Hope this helps,

  -Nairi

• Easy VPN setup with interface to multiples with the same level of security

  Hello

  I want to configure an ASA 5505 with 7.2 (4) software and dual license ISP and when I configure two interfaces with the level 0 on two security interfaces and enable vpnclient the trace message appear:

  ERROR: Cannot determine the internal and external interfaces Easy VPN remote: multiple interfaces with the same levels of security.

  vpnlclient of configuration above:

  vpnclient Server x.x.x.x where x.x.x.x
  vpnclient mode network-extension-mode
  vpnclient nem-st-autoconnect
  vpnclient TUNNEL_EZVPN_TUNNELSPEC vpngroup password *.
  vpnclient username usr_ezvpn_tunnelspec password *.
  vpnclient enable

  interfaces:

  interface Vlan200
  nameif outside1
  security-level 0
  IP x.x.x.x 255.255.255.252
  !
  interface Vlan300
  nameif outside2
  security-level 1
  IP x.x.x.x 255.255.255.128
  !

  monitor the SLA to the routing:

  monitor SLA 100
  type echo protocol ipIcmpEcho 200.221.2.45 interface outside1
  NUM-package of 5
  frequency 30
  monitor als 100 calendar life never start-time now
  ALS 200 monitor
  type echo protocol ipIcmpEcho 200.154.56.80 interface outside2
  NUM-package of 5
  frequency 30
  Annex monitor SLA 200 life never start-time now
  ALS 300 monitor
  type echo protocol ipIcmpEcho 4.2.2.1 interface outside1
  NUM-package of 5
  frequency 30
  Annex monitor SLA 300 life never start-time now
  ALS 400 monitor
  type echo protocol ipIcmpEcho 200.244.168.149 interface outside1
  NUM-package of 5
  Timeout 3000
  threshold of 3000
  frequency 30
  Annex monitor SLA 400 life never start-time now

  Follow-up:

  !
  track 1 rtr 400 accessibility
  !
  Track 2 rtr 200 accessibility
  !

  routes:

  Route 0.0.0.0 outside1 0.0.0.0 x.x.x.x 100 track 1
  Route 0.0.0.0 outside2 0.0.0.0 x.x.x.x 200 track 2

  The track works normal.

  Kind regards!

  Try using the command "backup interface" on the secondary ISP interface.

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/b_72.html#wp1338585

  You need to increase the level of security to 1 for this interface.

  By default, EasyVPN uses the highest level of safety inside and the lowest outside.  Anything between the two must be set manually.  I assume you have an interior vlan defined but not added to the posted config.

• VPN tunnel between 3 places

  Expertise of expensive

  Recently we hava configured vpn tunnel between two locations. Want to create a tunnel vpn on a third location. What configuration will be valid on the version of firewall cisco PIX 501 6.3.4.

  Please see thr existing pix config at two location.

  Please post the latest config?

• Why gesture to turn on my trackpad behaves not as before for switching between tabs when it works the same with all other programs besides Firefox?

  Why gesture to turn on my trackpad behaves not as before for switching between tabs when it works the same with all other programs besides Firefox?

  I changed the subject: config to make the rotation gesture to move between tabs and it worked great for well over a year. It now behaves properly, as described here:

  https://Bugzilla.Mozilla.org/show_bug.cgi?id=877598

  It used to be very controllable move a tab on, now it is erratic and moves quickly and the unexpected tabs regardless of the slowness, I do the gesture of rotation. It's the main reason I use Firefox on Chrome and I will continue to do so unless there is no solution for this.

  Just put the browser.gesture.twist.threshold to something around 15-25.