vShield Edge 5.1.2 load balancing HTTPS health check possible?

Similar Questions

• How do I see the IP Source address of a customer using ACE One-armed-mode of loading balance HTTP proxy request

  I use a device of 4710 Ace deployed in armed mode, use Source TAR to balancing HTTP request to a couple of Proxy servers.

  Everything works well, but the thing is that I do not see the client IP addresses on the Proxy logs, so I can't keep track of them.

  Interfaces and the Nat configs are:

  interface vlan 200

  Description of server-side-VLAN

  Bridge-Group 5

  NAT-pool 5 10.1.1.5 10.1.1.5 netmask 255.255.255.0 pat

  entered service VIP policy

  interface vlan 300

  Client-Side-VLAN description

  Bridge-Group 5

  interface bvi 5

  IP 10.1.1.3 255.255.248.0

  Interface Client-Server virtual description

  IP route 0.0.0.0 0.0.0.0 10.1.1.1

  and the policy looks like this

  Policy-map multi-game VIP

  class port 80

  Balancing vip continues

  policy of balancing port 80

  NAT Dynamics 5 vlan 200

  The resource assignment:

  Sticky ip-netmask 255.255.255.255 address two CLASSES of RESOURCES

  Timeout 5

  Serverfarm Service80

  Any suggestions will be appreciated,

  Thank you

  Hello

  You can use X-forwarded-for to insert the IP address of the client in the header Http. take a look at the link below:

  http://www.Cisco.com/en/us/products/HW/modules/ps2706/products_configura...

  Let me know if you have any questions.

  Kind regards
  Kanwal

  Sent by Cisco Support technique iPhone App

• Balancer load balancing vCloud weigh with POSSIBLE.

  Hello

  I try to get 2 vCloud Director of cells of load balanced through a vSheild edge load balancer. I'm running vCloud Director 5.1.0.810718 and vshield Manager 5.1.2 - 943471. The two cells are synchronized time, two cells have the same certificate and the two are running on vCloud Director. the vShield edge device is configured as high availability and 2 external interfaces and internal 1 interface. I have 2 pools server implemented in load balancing, 1 pool for the HTTP and the second basin of the consoleproxy. Virtual servers are also implemented, I created 2 virtual servers by using external links to http and consoleproxy. the instructions I used to set up cells and the edge device are shown in the vCloud Director vCloud 5.1 zero Part4 network load balancing. After reading the reading part in vCAT page 311 thru page 314 balancing, it indicates that I need to copy the SSL certificate to the for the public URL of http load balancer. My question is, how do copy you the SSL certificate in the load balancer? any help would be greatly appreciated.

  Thank you

  J

  J

  The method of the copy of the certificate in load balancing is different for each load balancing.  I find that it is only necessary if you're trying to unload SSL for HTTPS connection.  If you do not have SSL offloading, I don't worry about this.

  Look at what vCAT doc?  vCAT is a series of documents, and there are several versions.  I want to just make sure I'm looking at the same thing before commenting.

• Console Proxy doesn't work is not behind the edge load balancer

  I have a strange problem. I set up a load balancer with vShield Edge. Behind the load balancer, I have two cells vCloud. The Web interface works very well for users, but trying to connect a VMRC to view remote screen it displays 'connection' and then the session is disconnected.

  Then I stop the first cell and users can establish a VMRC connection again. When I activate the first cell once again, the web interface continues to work, but not the proxy of the console. Then I stop the second cell and now elements of the console working again.

  Any tips?

  Gabrié

  Have a similar setup and had the same problem.  Two things to check.  Go to c:\users\\appdata\local\temp\vmware- and open the last file vmware-vmrc - xxxx.log.  Towards the end, it should tell you why it's a failure.  For me, it was a conflict of thumbprint SSL, dating back to the different SSL certificates on the cells.  Also, be sure to vCloud Director Administration-Public address you have the right audiences VCD console address specified. To resolve the inconsistency of my mark, I just created a file certificates.ks a cell and then copied on the other cell and reran the script configures.  Good luck with VMware to help.  I opened a folder for this issue 6 days ago and have yet to get any help!

  -Craig

• Best way to HTTP in OSB load balancing

  Hello world
  
  We have a cluster of OSB and we must load balance HTTP requests on managed servers. Looking for info on OSB in load balancing, I found that there are essentially two options: use a hardware load balancer or a software solution like Weblogic HttpClusterServlet. For the moment, we have without balancer material available so we will have to take the option of software. I found a few articles on the configuration of HttpClusterServlet as http://redstack.wordpress.com/2010/12/20/using-weblogic-as-a-load-balancer.
  But I have a question for this configuration. If we use a managed server as a proxy HTTP requests between OSB as managed servers, what would happen if the server goes down? I think that one of the main objectives of a cluster deployment is to avoid a single point of failure, but with this configuration, all requests depend on the availability of the managed proxy server.
  
  Could you recommend a configuration of implementation of OSB load balancing?
  
  Thank you in advance,
  
  Daniel.

  Load Balancing in a cluster for http requests can be made using at least 4 different ways:

  (1) - use a hardware load balancer like F5 BigIP LTM
  (2) - use a web server with the plugin from weblogic to the cluster frontend
  (3) - use weblogic with HTTPClusterServlet
  (4) - use the DNS round robin - it works if you managed servers that run on 2 machines (say mach1, mach2) but on the same port. Client HTTP use hostname "mach" to access the URL and the dns has a resolution of names alternating Mach mach 1 and mach2 IP addresses...

  All options except (1) only achieve load balancing and not automatically failover all instances... Balancing load material has the additional feature to probe [sending periodic pings to targets], by which it can detect if the target resource is alive and do not send traffic to other nodes who are alive... That's why the hardware load balancers are worth their investment...
  other options may work if the client is encoded to a retry on failure... so on 2nd or subsequent attempt, the routing is done in the machine that is alive...

  For the options (1), (2)) and (3), you also need a redundancy of the system (material of load balancer, web server or weblogic) to avoid the single point of failure for load balancing... Balancers support material are usually deployed in redundant pairs to achieve...

  Published by: atheek1 on 11/22/2011 15:31

• vShield Edge balancer to load within vCloud Director?

  Hi all

  I had a long week, installation and configuration vCloud Director. So far, it looks great.

  However, I wanted to create a paralytic with 2 web servers and a LoadBalancer (vShield Edge device) in front of them. I just don't seem to be able to find anything about how I activate on the web site of vCloud Director. I can do the NAT and firewall, but balancing is missing ... I'm sure it's there somewhere, I'm just not see it!

  Can someone point me to the right direction?

  Bgrds,

  Finnzi

  This requires the additional license for vShield edge and configure vShield to vCenter PLugin.  There is no user interface in vCD interface to configure the load balaning VSE again.  1.5 introduces the possibility to configure VPN (if authorized), through vCD, but not the LB function again.

• vShield 5.5 - load balancer - trying to implement the signed certificate

  Some background information for the context:

  vShield Mgr 5.5:

  -imported Root CA Cert and a CA-signed X.509 cert.

  -capable to connect to vShield Mgr with certificates of trust.

  VCD cells:

  -all certificates signed and imported

  -able to connect directly with certificates of trust.

  balancer load vShield:

  VM: vcloud.ourcloudnet.com (10.10.10.1)

  Profile: http/https, least_conn, 80/443, the members are the two cells of vCD

  We want to have a cert signed and approved for load balancer address (vcloud.ourcloudnet.com). I tried to follow the procedures described in the Administration Guide vShield 73 page, but I'm getting confused with the procedure itself. When he says "you can generate a CSR and get it signed by a certification authority." If you generate a CSR at the global level, it is available for all vShield edges in your inventory. ", which means generating a CSR to the Mgr level as opposed to the Edge level vShield vShield? I'm doing this all wrong?

  Need advice please.

  I understood the question. When the certificate is ready to be downloaded, I need to select Base 64 encoded instead of the DER encoded. This will allow me to see the signed certificate in the format plain text and then paste the contents of the certificate signed when I import the certificate in the edge of load balancer device.

  When I did that I also fell on another question I want to create a new discussion on.

  Thanks anyway for the help.

• 5.1.2 is edge load balancing service logon aware?

  Hello

  We expect configure edge gateway Load Balancing Service using vCloud Director 5.1.2 and vCloud network and security 5.1.2

  Is it implemented no consciousness of the session of load balancing? I found a tip in this blog: http://blogs.vmware.com/vcloud/2012/11/how-to-configure-a-load-balancer-using-vcloud-networking-and-security-edge-device-vshield.html, but its not mentioned in the vCloud Director Administrator's Guide (5.1.1)

  If this is possible in 5.1.2 where can I get more information on that?

  What kind of awareness of the session is possible (cookie, setting html)?

  Best regards

  jmarschall

  Hello

  Yes, taking consciousness/session persistence is supported on the edge. As stated on the blog post you referenced, cookie based (HTTP) and SSL (HTTPS) ID session, as Source IP based session persistence is taken in charge. Use of cookies, you can still define if you want to use Insert cookie or cookie prefixing.

• Http-plugin supports metric base load balancing? like Mod_OC4J!

  He supports balancing the metric-based in Oracle 10 g AS OC4J.
  
  It's a good way to spread the query load among OC4Js based on a metric which was reported by OC4Js.
  
  When load balancing based on the metric system is enabled, requests are routed between based OC4Js on the report of a defined metric, as the ratio of round robin, automatic relaxing... etc.
  
  
  WebLogic server HTTP-Plugin has similar features? Could experts suggest simiilar workaround (s) or solution (s) Please?

  Johna Pakas wrote:

  Sean KTN says:

  Kumashiro Shiniti wrote:

  Johna Pakas wrote:

  I think you should connect with Oracle Sales. Let them to clarify.

  It is a good idea.

  Since now, WLS have no metric based load balancing.
  For load balancing, you must configure the proxy servers.

  http://e-docs.BEA.com/WLS/docs103/cluster/setup.html
  http://e-docs.BEA.com/WLS/docs103/cluster/load_balancing.html

  Give them some pressure to release new features.

  My concern, metric according to load balancing is explicitly vital for most of the users using OC4J. Y at - it no alternative to measure loading WLS? As I can build module
  or plugin Web levels... of course raise this request to my sys development team exactly.

  WLS do support 3 types:-Round Robin load balancing, load balancing based on the weight & Random load balancing.
  In the near future, I guess they do not provide as metric base load balancing MOD_OC4J.

  If you like to take some tasks to measure, I sugget contact you your sales local oracle for assistance. They have probably you persuade enjoying service professinal anyway.

• Hi ALL, did any attempt on the virtual computer NETWORK load balancing using HYPERV on UCS blades

  I try to configure the CASE server cluster by using the Unicast NLB on the virtual machine on different blades on the UCS, it works for awhile, then he abandoned packages.

  I heard that this screenplay of unicast is not supported in the UCS when she used END-host mode in the fabric interconnet...? any attempted before.

  Would it, I use the multicast mode is that something needs to be done on the FBI62020 or the LAN switch upstream. ??

  Header note I found on the implementation of UCS for mulitcast NLBL:

  Microsoft NLB can be deployed in 3 modes:

  Unicast

  Multicast

  IGMP multicast

  For series B UCS deployments, we have seen that the multicast and IGMP multicast work.

  IGMP multicast mode seems to be the more reliable deployment mode.

  To do this, the monitoring settings:

  All NLB Microsoft value "Multicast IGMP" nodes.  Important!  Check ths by logging into EACH node independently.  Do not rely on the MMC of NLB snap.

  An IGMP applicant must be present on the VLAN of NLB.  If PIM is enabled on the VIRTUAL LAN that is your interrogator.  UCS cannot function as applicant IGMP.  If an interrogator of functioning is not present, NLB IGMP mode will not work.

  You must have a static ARP entry on cheating it upstream pointing IP address Unicast NLB on the multicast MAC address NETWORK load balancing.  This need will set up, of course, on the VLAN of the NLB VIP. The key is that the routing for the NLB VLAN interface must use this ARP entry as a unicast IP ARP response may not contain a multicast mac address. (Violation of the RFC 1812)  Hosts on the NLB VLAN must also use the static entry.  You may have several entries ARP.  IOS can use a function of 'alias' of ARP. (Google it.)

  How Microsoft NLB works. -The truncated for brevity Mac addresses.

  TOPOLOGY OF NLB MS

  NETWORK VLAN 10 = subnet 10.1.1.0/24 IP load balancing

  VIP = 10.1.1.10 NETWORK LOAD BALANCING

  Arp entry static switch advanced IP 10.1.1.10 upstream to MAC 01

  NLB VIP (MAC 01, IP 10.1.1.10)

  NODE-A (AA, MAC IP:10.1.1.88)

  NŒUD-B (MAC BB, IP:10.1.1.99)

  Using the IGMP snooping and interrogator VLAN snooping table is filled with the mac NLB address and groups pointing to the appropriate L2 ports.

  MS NLB nodes will send the responses of IGMP queries.

  This snooping table could take 30 to 60 seconds to complete.

  Host on VLAN 200 (10.200.1.35) sends traffic to NETWORK VIP (10.1.1.10) load balancing

  It goes of course to VLAN 10 interface that uses the static ARP entry to resolve to address MAC 01 VIP NETWORK load balancing.

  Since it is a multicast frame destination it will be forward by the IGMP snooping table.

  The framework will arrive at ALL NLB nodes. (NŒUD-A & NŒUD-B)

  NLB nodes will use its load balancing algorithm to determine which node will manage the TCP session.

  Only one NLB node will respond to this host with TCP ACK to start the session.

  NOTES

  This works in a VMware with N1k, standard vSwtich and vDS environment. Where surveillance IGMP is not enabled, the framing for VIP MAC NETWORK load balancing will be flooded.

  NLB can only work with TCP-based services.

  As stated previously mapping an IP unicast to a multicast mac address is a violation implied by RFC 1812.

  TROUBLESHOOTING

  Make sure your interrogator is working. Just to clarify that this does not mean that it is actually at work.

  Wireshark lets check that IGMP queries are received by the NLB nodes.

  Make sure that the ARP response works as expected.  Once Wireshark again is your friend.

  Look at the paintings IGMP snooping. Validate the L2 ports appearing as expected.

  CSCtx27555 [Bug-preview for CSCtx27555] Unknown multicast with destination outside the range MAC 01:xx: are deleted. (6200 FI fixed in 2.0.2m)

  IGMP mode not affected.

  CSCtx27555    Unknown multicast with destination outside the range MAC 01:xx: are deleted.

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtx27555

  fixed in 2.0(2m)

  Solution: Change the NLB mode of operation of "Multicast" to "multicast IGMP', which modifies balancing load NETWORK VIP MAC at 0100.5exx.xxx Beach, allows to transfer occur as expected.

  Q: and if I switch to switch mode, which means all of the profile and the settings on the servers are completely exhausted and I need to recreate them. ???

  A:Cisco Unified Computing System Ethernet switching Modes

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns517/ns224/ns944/whitepaper_c11-701962.html

  -There is no impact on the configuration, you have done service profiles.  they will continue to work as expected.  Mode selector has the FI behave more like a conventional switch.  Most notable is that Spanning tree will be activated and if you have several uplinks yew, tree covering weight will begin to block redundant paths.

  You need to review your topology and what impact tree covering weight.  Generally, we at the switch port upstream defined as "edge master", you want to delete this line.

  For pre-production and laboratory environment, PDI can help qualified with the planning, design and implementation partners.  Given to review the IDP site and open a case if you need more detailed assistance.

• Network Load Balancing error

  Hello

  I have DC with 192.168.10.2 255.255.255.0 P.DNS 192.168.10.2 & ADC 192.168.10.3 P.DNS 192.168.10.2 255.255.255.0

  When I configure the network load balancing in win2012r2 std I get below error. Please help on this.

  "NLB Manager running on a system with all networks bound to NLB mifht does not work as expected.
  If all interfaces are ser to run NLB in "unicast" mode, Manager NLB will fail to connect to the hosts. »

  Thank you.

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• OSPF load balancing

  Hello

  Does anyone know how to deploy load balancing in OSPF area 0?

  Any suggestion for documentation would be apreciated.

  Thanks in advance for your help

  Hello

  OSPF is only the equal cost load balancing, so you must have two channels with equal to the destination charges.

  This command must also be set to more than one:

  maximum-paths

  under router ospf configuration.

  I think you also need ip cef enabled.

  See this link for more information:

  http://www.Cisco.com/warp/public/105/loadbal_cef.html#beforecef

  Aaron

  Hope that this help - remember to note messages :-)

• Load Balancing does not not on 2911

  Hello people,

  I have some difficulty to operate the Load Balance on my 2911.

  I have followed the editing on this site:

  http://www.Cisco.com/en/us/Tech/tk648/tk361/technologies_configuration_example09186a0080950834.shtml

  and APARENTLY it works, but not in reality, because I see packets using a NAT IPS bot thru, but when I check on the interfaces I see we're not receive / send anything.

  Background:

  G0/0, I have one ISP, other 1/G0, G0/2 my network.

  Building configuration...

  Current configuration: 6045 bytes

  !

  ! Last configuration change to 15:47:49 UTC Tuesday, January 28, 2014 by alan

  ! NVRAM config update at 14:32:59 UTC Tuesday, January 28, 2014 by alan

  ! NVRAM config update at 14:32:59 UTC Tuesday, January 28, 2014 by alan

  version 15.1

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  ROUTER1 hostname

  !

  boot-start-marker

  boot-end-marker

  !

  !

  logging buffered 51200 warnings

  !

  No aaa new-model

  !

  !

  No ipv6 cef

  IP source-route

  IP cef

  !

  !

  !

  !

  dhcp LAN_DHCP_POOL IP pool

  network 192.168.0.0 255.255.0.0

  default router 192.168.2.2

  domain g_bacon

  DNS 8.8.8.8 Server 208.67.222.222

  0 8 rental

  !

  !

  no ip domain search

  IP host ROUTER1 192.168.2.2

  8.8.8.8 IP name-server

  name-server IP 208.67.222.222

  IP-server names 8.8.4.4

  IP-server names 208.67.220.220

  !

  Authenticated MultiLink bundle-name Panel

  !

  !

  Crypto pki token removal timeout default 0

  !

  Crypto pki trustpoint TP-self-signed-2101532551

  enrollment selfsigned

  name of the object cn = IOS - Self - signed - certificate - 2101532551

  revocation checking no

  rsakeypair TP-self-signed-2101532551

  !

  !

  TP-self-signed-2101532551 crypto pki certificate chain

  certificate self-signed 01

  3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201

  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30

  69666963 32313031 35333235 6174652D 3531301E 32313137 OF 31323239 170 3131

  31335A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D

  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 31303135 65642D

  33323535 3130819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101

  8100DEA3 06574FDF B2B2113F 84A1EF39 9969F4D9 04131994 A3FCC466 D0328CCF

  B219F1AE A3DCC204 CD993BB2 F59C9A7F C251024E 382162 5 D9277CEB F1A575A5

  0356 C 896 A7A1BB48 8EA4CFF6 DA77B72C 9904A73B 6731A6E0 3004E5EA B44C1F7F

  5667496C 1E8E603D BE9B1AA1 1065E449 F6110C17 1A5FE3B9 3593BF87 96E14DEC

  010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 87FF0203

  551 2304 18301680 14E5F8C8 C30593C3 CEAB1874 F94F070B 9674F152 AD301D06

  03551D0E 04160414 E5F8C8C3 0593C3CE AB1874F9 4F070B96 74F152AD 300 D 0609

  2A 864886 F70D0101 A 05050003 81810092 51314, 50 EA812CDA AC97A8D1 2CA06BCC

  6FD5B4A6 DA888322 E2166AB4 0CF340BB E0407C95 584A1BDF 5DC3A6EE 2862E9CF

  7BF0C831 54F06ABF 011664 D 3 75269FF3 02D434BD 0FD15F32 EB34730C 47FE29D9

  7C2BBF9D 5BDB1D4F EEBFBED5 9B07450E 83DA57B2 1F296D0A 52D39A8F 6A 679244

  05C0924C F3FA9A05 53198E BDB28409

  quit smoking

  license udi pid CISCO2911/K9 sn FTX1553AJQU

  !

  !

  username privilege 15 secret 5 alan $1$ b6Jk$ 8iz3K3cTUgSZ.VePkKl5a.

  !

  redundancy

  !

  !

  !

  !

  !

  class-map correspondence-any PROHIBIDAS

  Protocol httpwww.facebook.comhost game «»

  Protocol httpwww.youtube.comhost game «»

  match Protocol http host 'www.pornotube.com.

  Protocol http host «www.xvideos.com» game

  match Protocol http host 'www.mega.co.nz'.

  match Protocol http host 'www.radios-on-line.com.ar'.

  match Protocol http host 'www.enlaradio.com.ar'.

  Protocol http host «www.cienradios.com.ar» game

  match Protocol http host 'www.radios-argentina.com.ar'.

  match Protocol http host 'www.fmyam.com.ar'.

  Protocol http host «www.piratebay.org» game

  class-map match-all P2P

  winmx Protocol game

  gnutella Protocol game

  bittorrent Protocol game

  match Protocol kazaa2

  !

  !

  Policy-map DROP_PROHIBIDAS

  class PROHIBIDAS

  drop

  class P2P

  drop

  !

  !

  !

  !

  !

  !

  !

  !

  the Embedded-Service-Engine0/0 interface

  no ip address

  Shutdown

  !

  interface GigabitEthernet0/0

  Fibertel description

  DHCP IP address

  IP access-group acl101 in

  IP access-group out acl101

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  No cdp enable

  out of service-policy DROP_PROHIBIDAS

  !

  interface GigabitEthernet0/1

  Arnet description

  IP 186.153.125.138 255.255.255.248

  IP access-group acl101 in

  IP access-group out acl101

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  No cdp enable

  out of service-policy DROP_PROHIBIDAS

  !

  interface GigabitEthernet0/2

  IP 192.168.2.2 255.255.0.0

  IP access-group block_FB in

  IP access-group out acl101

  IP nat inside

  IP virtual-reassembly in

  IP tcp adjust-mss 1452

  automatic duplex

  automatic speed

  No cdp enable

  !

  router RIP

  version 2

  network 192.168.0.0

  !

  IP forward-Protocol ND

  !

  IP http server

  IP 8180 http port

  20 class IP http access

  IP http secure server

  IP http timeout policy slowed down 60 life 86400 request 10000

  !

  IP nat inside source map route address interface GigabitEthernet0/1 overload

  IP nat inside source map route fibertel interface GigabitEthernet0/0 overload

  IP route 0.0.0.0 0.0.0.0 track GigabitEthernet0/0 123

  IP route 0.0.0.0 0.0.0.0 200.122.102.1 254

  !

  block_FB extended IP access list

  deny ip 192.168.0.0 0.0.255.255 welcome 173.252.100.16

  deny ip 192.168.0.0 0.0.255.255 173.252.64.0 0.0.63.255

  deny ip 192.168.0.0 0.0.255.255 31.13.24.0 0.0.7.255

  deny ip 192.168.0.0 0.0.255.255 31.13.64.0 0.0.63.255

  deny ip 192.168.0.0 0.0.255.255 66.220.144.0 0.0.15.255

  deny ip 192.168.0.0 0.0.255.255 69.63.176.0 0.0.15.255

  deny ip 192.168.0.0 0.0.255.255 69.171.224.0 0.0.31.255

  deny ip 192.168.0.0 0.0.255.255 74.119.76.0 0.0.3.255

  deny ip 192.168.0.0 0.0.255.255 103.4.96.0 0.0.3.255

  deny ip 192.168.0.0 0.0.255.255 204.15.20.0 0.0.3.255

  IP 192.168.0.0 allow 0.0.255.255 everything

  allow an ip

  !

  access-list 110 permit ip 192.168.0.0 0.0.255.255 everything

  !

  !

  !

  !

  route allowed fibertel 10 map

  corresponds to the IP 110

  is the interface GigabitEthernet0/0

  !

  arnet allowed 10 route map

  corresponds to the IP 110

  is the interface GigabitEthernet0/1

  !

  !

  !

  control plan

  !

  !

  exec banner ^ C ^ C

  connection of the banner ^ C ^ C

  Banner motd ^ C ^ C

  !

  Line con 0

  local connection

  line to 0

  line 2

  no activation-character

  No exec

  preferred no transport

  transport of entry all

  transport output pad rlogin lapb - your MOP v120 udptn ssh telnet

  StopBits 1

  line vty 0 4

  access-class 23 in

  privilege level 15

  local connection

  transport input telnet ssh

  line vty 5 15

  access-class 23 in

  privilege level 15

  local connection

  transport input telnet ssh

  !

  Scheduler allocate 20000 1000

  end

  So far so good, I have check the transactions of NAT:

  ROUTER1 #show ip nat trans

  Inside global internal local outside global local outdoor Pro

  TCP 200.122.102.74:62114 192.168.0.1:62114 17.151.239.110:443 17.151.239.110:443

  TCP 200.122.102.74:62119 192.168.0.1:62119 17.172.233.134:5223 17.172.233.134:5223

  TCP 200.122.102.74:34945 192.168.0.2:34945 181.30.241.103:443 181.30.241.103:443

  TCP 200.122.102.74:37444 192.168.0.2:37444 173.194.42.230:443 173.194.42.230:443

  TCP 200.122.102.74:37695 192.168.0.2:37695 181.30.241.109:80 181.30.241.109:80

  TCP 200.122.102.74:40662 192.168.0.2:40662 173.194.74.188:5228 173.194.74.188:5228

  TCP 186.153.125.138:41426 192.168.0.2:41426 216.115.101.179:443 216.115.101.179:443

  TCP 200.122.102.74:41484 192.168.0.2:41484 216.115.101.179:443 216.115.101.179:443

  TCP 200.122.102.74:42381 192.168.0.2:42381 181.30.241.31:80 181.30.241.31:80

  TCP 186.153.125.138:42553 192.168.0.2:42553 98.136.223.39:8996 98.136.223.39:8996

  and I see they're going through the two connections.

  Buuuuuuuuuuuuut, when I check the interfaces...

  ROUTER1 #show int g0/0

  GigabitEthernet0/0 is up, line protocol is up

  Material is CN Gigabit Ethernet, the address is c464.1354.b8c0 (BIA c464.1354.b8c0

  )

  Description: Fibertel

  The Internet address is 200.122.102.74/24

  MTU 1500 bytes, BW 100000 Kbit/s, DLY 100 usec,

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  KeepAlive set (10 sec)

  Full-Duplex, 100 Mbps, media type is RJ45

  control output stream is XON, control of input stream is XON

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry of 00:00:00, 00:00:00 exit, exit hang never

  Final cleaning of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0

  Strategy of queues: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 774000 bps, 161 packets/s

  5 minute output rate 423000 bps, 102 packets/s

  2133521 package, 1223904205 bytes, 0 no buffer entry

  Received 615778 broadcasts (0 of IP multicasts)

  0 Runts, 0 giants, 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  Watchdog 0, multicast 0, break 0 comments

  1065308 packets output, 214203455 bytes, 0 underruns

  0 output errors, 0 collisions, 1 interface resets

  unknown protocol 0 drops

  0 babbles, collision end 0, 0 deferred

  1 lost carrier, 0 no carrier, interrupt the output of 0

  output buffer, the output buffers 0 permuted 0 failures

  ROUTER1 #show int g0/1

  GigabitEthernet0/1 is up, line protocol is up

  Material is CN Gigabit Ethernet, the address is c464.1354.b8c1 (BIA c464.1354.b8c1

  )

  Description: arnet

  The Internet address is 186.153.125.138/29

  MTU 1500 bytes, BW 100000 Kbit/s, DLY 100 usec,

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  KeepAlive set (10 sec)

  Full-Duplex, 100 Mbps, media type is RJ45

  control output stream is XON, control of input stream is XON

  Type of the ARP: ARPA, ARP Timeout 04:00

  Last entry 00:04:01, 00:00:06 exit, exit hang never

  Final cleaning of "show interface" counters never

  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0

  Strategy of queues: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 0 bps, 0 packets/s

  5 minute output rate 0 bps, 0 packets/s

  208948 packages, 153515983 bytes, 0 no buffer entry

  Received 1236 broadcasts (0 of IP multicasts)

  0 Runts, 0 giants, 0 shifters

  entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored

  Watchdog 0, multicast 0, break 0 comments

  190283 packets output, 45657373 bytes, 0 underruns

  0 output errors, 0 collisions, 0 resets interface

  unknown protocol 0 drops

  0 babbles, collision end 0, 0 deferred

  carrier, 0 no carrier, lost 0 0 interrupt output

  output buffer, the output buffers 0 permuted 0 failures

  Everything happens through G0/0 and nothing in G0/1!

  Any ideas on why this is happening?

  Thank you in advance for your help!

  Kind regards

  Alan

  Hello

  Yes here you only have a single default route installed (one from the DHCP server) so it can't NAT on the other interface as it can route on this one.

  Change your configuration like this:

  no ip route 0.0.0.0 0.0.0.0 track GigabitEthernet0/0 123

  no ip route 0.0.0.0 0.0.0.0 200.122.102.1 254

  IP route 0.0.0.0 0.0.0.0 dhcp

  IP route 0.0.0.0 0.0.0.0 200.122.102.1 254

  Now if you want to follow the first route look at this document:

  http://www.Cisco.com/en/us/docs/iOS/dial/configuration/guide/dia_rel_stc_rtg_bckup.html#wp1065528

  Concerning

  Alain

  Remember messages useful rate.

• Double connection ISP and load balancing

  Hi all

  I have the Cisco 2911 router k 9/s with 3 GB ports. I have also two different ISP connections, all have two different available bandwidth (one is asymmetrical, else a symmetrical).

  What I want to achieve is to ensure the balance of Nice load between two ISPS for all PCs behind the NAT device.

  What I know so far, it's that I can use CEF or PfR/REL. For both of this technology, I have some doubts.

  CEF: distributes the network load between the two connections based on sessions (which is good, because I strongly to use tools like Skype or Lync for audio/video conversations). However, what is happening, when I get on one of the ISP connections broadband bandwidth max? He's going to choke for 50% of the connections? Or it will detect the use of bandwidth and to force using second ISP?

  PfR/REL: as far as I understood it resolves my concern regarding the use of the connection, but what happens to the session? Should it also be based on this mechanism? As you know that it is very important for audio/video connections.

  Are there other tools that can provide these load balancing? I know DAB, but I don't want to decide manually, where each service (e.g. http or ssh) will have to go. I'm looking for something more automated.

  Thanks in advance for any help.

  Piotr

  Hello

  I assume that you have a static route for the subnet 213.192.65.0/24 on top of the output and with the combination of order

  network default IP 213.192.65.105 213.192.65.105 IP address is installed as a default gateway. What is the #2 ISP?

  If so, it explains why he always goes on ISP2 only.

  http://www.Cisco.com/en/us/Tech/tk365/technologies_tech_note09186a0080094374.shtml#flagging

  Just remove the config:

  Noneip default-network 213.192.65.105

  Noneip default-gateway 213.192.65.105

  Then again check the routing table:

  SH ip route

  Hope it helps.

  Best regards
  Akim

• RV042 load balancing problem

  We have two network connections coming into the office. One is a private Wan, and the other is a WAN on the internet. We have a RV042 router configured for load balancing. We have our private WAN which includes Exchange and 6 VPN Wan1. On WAN2, we have a public IP address and home workers. Both connections are 5 Mg T1s and both have the ability to access the internet but only wan2 has a public IP (76.x.x.x) were as WAN1 has a private IP address. (10.x.x.x).

  Were now the problem lies is our new website based on payroll, system does not support load balancing. We have on one hand stop when we do pay (Tower load balancing off.)

  Now is it possible to use our computers to pay only one side? change the host file maybe? Or force a certain MAC address of use only the WAN1 or is there a better router to achieve?

  Any help would be appreciated

  Peter Labelle

  I don't have a RV042 and have had reference to the Administrator's guide:

  http://www.Cisco.com/en/us/docs/routers/CSBR/RV042/Admin/Guide/RV042_V10_UG_C-Web.PDF

  I hope these comments are useful. Perhaps you can comment and let me know if it works for you. Check balancing load and the binding protocol section.  These changes are disruptive... Please assume a failure during the change.  Not a long interruption, but the sessions at the same distance could be lowered.

  Out, you can use the protocol binding. This could cause some problems with the VPN client... you can try this after hours?

  For entrants, how customers and remote computers know the accounting software?  You are advertising this IP address via a link or another?

  If you are, then you can have a preference through one of the links.  If you advertise this IP address then you will not be able to provide a preference to a supplier of services on the other.

  Do please see the Administrator's guide and let me know your thoughts.  Sincere greetings and HTH,

  Andrew Lissitz