Vulnerability ID: NON-2015-0211 on my WNDR4500v3 router

Similar Questions

• After the analysis of my PC - WARNING vulnerability ID: NON-2015-0211, help please

  The report says that my firmware is out of date and that it upgraded. So, as any reasonable computer geek I checked out your site and found the upgrade you suggested to other people with the same problem... download to v1.1.2.12. I downloaded and followed the instructions, there is no download, several times. I watched my router on your site and went to his specific download page and there the last update was the he version to what I have installed on it (v1.0.0.48), so I don't know if there is an update, you can direct me. Any help greatly appreciated ywould.

  Sincerely,

  Sethos099

  Unfortunately, there will be no update future firmware for the router.

  This is because the router is already EOL.

  Consider getting a newer model.

• Using 36 FF but still get the message on tests of vulnerability for hack "Freak."

  "Attention!" Your client is vulnerable to CVE-2015-0204. Even if your client does no suites RSA to EXPORT, it can still be fooled into using one of them. We encourage you to upgrade your client. "

  https://nakedsecurity.Sophos.com/2015/03/04/the-freak-bug-in-tlsssl-what-you-need-to-know/

  "As far as we know, the trick does not work against TLS implementations used by Microsoft, Google and Mozilla.

  If the users of Internet Explorer, chrome/Chrome and Firefox are OK. »

  This affects pretty much just Android users default browser on older versions of Android, Safari users and browsers old and obsolete. Users using Firefox 36 as safe from this attack (at least insofar as it is currently understood)

• Adobe CC 2015 programs do not start

  Hello, I really need help. My CC 2015 programs will not start. I go to the Task Manager and they appear quickly (when I click on them), but then immediately disappear. They want to start but can not. However, my non - 2015 CC programs work quite well (for example, CS6, Scout CC, edge Fireworks animate CC). I disabled my firewall and it does not always help. I have uninstalled/reinstalled, signed out/in, several times...

  Any Suggestions?

  Hi guys,.

  I thank very you much for trying to help out. I was actually with Adobe support for about 3 hours trying to get this up and running. Finally done! It is Windows 7, which had to be completely updated. So if anyone has any questions as I've described, see your Windows updates first. Make sure that everything is compatible with the installation.

  Thanks again!

  Sarah

• WNDR4500v3 is not running in 802.11n mode

  Hello

  I have a Netgear WNDR4500v3 router (N900) and I have noticed that I use in my band of 2.4 ghz in 802.11 g and my 5 GHz band (which I use exclusively for the game features) runs in 802. 11A. The router itself should not be performed in n? I have a wireless card in my PC that supports Wi - Fi N and 5 GHz and when WifiInfoViewer using almost all the other networks around my area appear as N but not of my two SSID not. I went through the control panel of the router and I don't see anything to change... I'm no expert in networks, but I feel my router is not reached its full potential and maybe that's why?

  in any case... Thank you

  Keith

  WPA2 security is required for check N, to be sure, that you use. WMM also must be activated also.

• Sign in required when you use the classic/2015 Installer

  I'm trying to deploy Acrobat Standard DC.

  I logged on to the site of license and downloaded Acrobat_2015_Web_WWMUI.exe (description: Acrobat DC2015 12.0 WIN ESD ALL CLASSIC)

  I downloaded the Acrobat DC Customization Wizard

  I wrote the serial number of the license site for Acrobat 12.0 English universal Windows LIC SN

  In the "Customization Options" CustWiz I entered the serial number (copied and pasted to check that there is no error in transposition)

  In the CustWiz 'Online services and features', I checked disable them the product updates, Upsell turn off and disable all services

  I saved the package, which has created AcroPro.mst

  I also transform > generate transformation and has called myInstall.mst

  I then deployed acropro.msi with TRANSFORMS = "AcroPro.mst" (and also tried with MyInstall.mst) and it installs successfully the program. "

  I checked the path is C:\Program Files (x 86) \Adobe\Acrobat 2015\ which means the classic route Setup

  When I try to launch Adobe Acrobat DC, I'm Guest Sign In just...

  According to the plan prior to the deployment of ETK, granting of rights of use section, it is said that "prior active Admin for all users".

  What does enter the serial number in the Customization Wizard (which I did) or is there something else I need to do to activate this license/serial number so that I can avoid this thing all sign-in and run Acrobat DC just as we have in the past?

  Connect to the launch is required until you click 'exception Grant Offline' button next to the serial number field of CW. When you click this button, your computer must be connected to the internet.

• How to solve backup permissions?

  Following the instructions in the:

  <"rel = 'nofollow' > https://developer.mozilla.org/en-US/Firefox_OS/Phone_guide/Flame/Updating_your_Flame#Backing_up_and_restoring_your_Flame_data > "

  I could back up my old phone with script of B2G-flash-tool. And I could push most of this backup on a new phone, but he hung up and kind of crapped on my phone. Calendar and e-mail applications had given, but the market wouldn't even load. I just got a blank screen. So I re-flashed my phone and set up from scratch. I want to back up the basic settings that I have now, but I get warnings and no data is stored:

       amanda@mona:B2G-flash-tool$ python backup_restore_profile.py -b -p ../Squid/sep13bak
       2015-09-13 18:02:22,590 - utilities.adb_helper - INFO - restarting adbd as root
  

       2015-09-13 18:02:22,590 - __main__ - INFO - Target device [None]
       2015-09-13 18:02:22,594 - __main__ - INFO - Stop B2G.
       2015-09-13 18:02:22,601 - __main__ - INFO - Backing up profile...
       2015-09-13 18:02:22,601 - __main__ - INFO - Backing up Wifi information...
       2015-09-13 18:02:22,616 - __main__ - WARNING - If you don't have root permission, you cannot backup Wifi information.
       2015-09-13 18:02:22,616 - __main__ - INFO - Backing up /data/b2g/mozilla to /tmp/backup_restore_ma6OPK/b2g-mozilla/ ...
       2015-09-13 18:02:22,626 - __main__ - WARNING - Can not pull files from /data/b2g/mozilla to /tmp/backup_restore_ma6OPK/b2g-mozilla/
       2015-09-13 18:02:22,627 - __main__ - INFO - Backing up /data/local to /tmp/backup_restore_ma6OPK/data-local/ ...
       2015-09-13 18:02:22,646 - __main__ - WARNING - Can not pull files from /data/local to /tmp/backup_restore_ma6OPK/data-local/
       2015-09-13 18:02:22,647 - __main__ - INFO - Backup profile done.
       2015-09-13 18:02:22,647 - __main__ - INFO - Copy profile from /tmp/backup_restore_ma6OPK to [../Squid/sep13bak].
       2015-09-13 18:02:22,647 - __main__ - INFO - Start B2G.
  

  The process creates a "sep13bak" directory and create subfolders for b2g-mozilla, given local and wifi, but they are all empty. I can't understand why I would not be able to pull files. I didn't need to root on my old phone. Is there a setting that I rocked long time that I'm missing here?

  Ugh. Too bad. I had to literally just disable "USB storage".

• ESXi bnx2x problem!

  Hello, today the esxi server failed in CMTF. In a discharge of these events:

  [7m2015-09-24T22:50:54.755Z cpu19:33255)WARNING: LinNet: netdev_watchdog:3678: NETDEV WATCHDOG: vmnic0: transmit timed out [0m
  2015-09-24T22:50:54.755Z cpu19:33255)WARNING: at vmkdrivers/src_92/vmklinux_92/vmware/linux_net.c:3707/netdev_watchdog() (inside vmklinux)
  2015-09-24T22:50:54.755Z cpu19:33255)Backtrace for current CPU #19, worldID=33255, rbp=0x43063118ecb0
  2015-09-24T22:50:54.755Z cpu19:33255)0x4390cf39be10:[0x41800d696dfe]vmk_LogBacktraceMessage@vmkernel#nover+0x22 stack: 0x13, 0x41800dd1f
  2015-09-24T22:50:54.755Z cpu19:33255)0x4390cf39be30:[0x41800dd1f7b7][email protected]#9.2+0x27f stack: 0x43063117cce
  2015-09-24T22:50:54.755Z cpu19:33255)0x4390cf39bea0:[0x41800dd45a5f][email protected]#9.2+0xd7 stack: 0x4306
  2015-09-24T22:50:54.755Z cpu19:33255)0x4390cf39bf30:[0x41800d64fa52]helpFunc@vmkernel#nover+0x4e6 stack: 0x0, 0x43063117cce0, 0x27, 0x0,
  2015-09-24T22:50:54.755Z cpu19:33255)0x4390cf39bfd0:[0x41800d812aee]CpuSched_StartWorld@vmkernel#nover+0xa2 stack: 0x0, 0x0, 0x0, 0x0, 0
  2015-09-24T22:51:16.840Z cpu10:33254)<3>[bnx2x_clean_tx_queue:1626(vmnic0)]timeout waiting for queue[0]: txdata->tx_pkt_prod(65183) != txdata->tx_pkt_cons(63170)
  2015-09-24T22:51:38.901Z cpu10:33254)<3>[bnx2x_clean_tx_queue:1626(vmnic0)]timeout waiting for queue[0]: txdata->tx_pkt_prod(65183) != txdata->tx_pkt_cons(63170)
  2015-09-24T22:51:51.244Z cpu16:33415)NMP: nmp_ThrottleLogForDevice:3178: Cmd 0x12 (0x43a5c8c7cd00, 0) to dev "naa.600508b1001c06cde91a898a5f4a6294" on path "vmhba0:C0:T0:L1" Failed: H:0x0 D:0x2 P:0x0 Valid sense data: 0x5 0x24 0x0. Act:NONE
  2015-09-24T22:53:29.623Z cpu0:33254)<3>[bnx2x_state_wait:319(vmnic0)]timeout waiting for state 7
  2015-09-24T22:53:29.857Z cpu0:33254)IntrCookie: 1903: cookie 0x1c moduleID 4110 <vmnic0> exclusive, flags 0x25
  2015-09-24T22:53:29.857Z cpu0:33254)IntrCookie: 1903: cookie 0x1e moduleID 4110 <vmnic0-fp-0> exclusive, flags 0x25
  2015-09-24T22:53:29.857Z cpu0:33254)<6>bnx2x 0000:02:00.0: vmnic0: using MSI-X  IRQs: sp 16  fp[0] 26 ... fp[7] 33
  2015-09-24T22:53:31.078Z cpu0:33254)IntrCookie: 1903: cookie 0x1f moduleID 4110 <vmnic0-fp-1> exclusive, flags 0x25
  2015-09-24T22:53:31.122Z cpu9:33249)<3>bnx2x: [bnx2x_attn_int_deasserted3:4518(vmnic0)]MC assert!
  2015-09-24T22:53:31.122Z cpu9:33249)<3>bnx2x: [bnx2x_mc_assert:894(vmnic0)]XSTORM_ASSERT_LIST_INDEX 0x2
  2015-09-24T22:53:31.122Z cpu9:33249)<3>bnx2x: [bnx2x_mc_assert:908(vmnic0)]XSTORM_ASSERT_INDEX 0x0 = 0x00000000 0x00000000 0x00000000 0x00010026
  2015-09-24T22:53:31.122Z cpu9:33249)<3>bnx2x: [bnx2x_mc_assert:922(vmnic0)]Chip Revision: everest2, FW Version: 7_8_52
  2015-09-24T22:53:31.122Z cpu9:33249)<3>bnx2x: [bnx2x_attn_int_deasserted3:4524(vmnic0)]driver assert
  2015-09-24T22:53:31.123Z cpu0:33254)<3>[bnx2x_esx_set_vlan_stripping:5947(vmnic0)]Failed to configure VLAN stripping for Queue 1
  2015-09-24T22:53:31.123Z cpu0:33254)IntrCookie: 1903: cookie 0x20 moduleID 4110 <vmnic0-fp-2> exclusive, flags 0x25
  2015-09-24T22:53:31.145Z cpu0:33254)<3>bnx2x: [bnx2x_setup_queue:9147(vmnic0)]Queue(2) SETUP failed
  2015-09-24T22:53:31.145Z cpu0:33254)<3>[bnx2x_esx_setup_queue:599(vmnic0)]Queue 2 setup failed[0xfffffffb]
  2015-09-24T22:53:31.145Z cpu0:33254)<3>[bnx2x_esx_init_netqs:932(vmnic0)]Could not start tx netq[-5]:2
  2015-09-24T22:53:31.166Z cpu0:33254)<3>[bnx2x_queue_chk_transition:5310(vmnic0)]Blocking transition since pending was 20
  2015-09-24T22:53:31.166Z cpu0:33254)<3>[bnx2x_queue_state_change:4499(vmnic0)]check transition returned an error. rc -16
  2015-09-24T22:53:31.360Z cpu9:33249)<3>bnx2x: [bnx2x_panic_dump:1097(vmnic0)]begin crash dump -----------------
  2015-09-24T22:53:31.360Z cpu9:33249)<3>bnx2x: [bnx2x_panic_dump:1103(vmnic0)]def_idx(0x2)  def_att_idx(0x3)  attn_state(0x101)  spq_prod_idx(0x6) next_stats_cnt(0x0)
  2015-09-24T22:53:31.360Z cpu9:33249)<3>bnx2x: [bnx2x_panic_dump:1108(vmnic0)]DSB: attn bits(0x0)  ack(0x101)  id(0x10)  idx(0x3)
  <3>bnx2x: [bnx2x_panic_dump:1109(vmnic0)]     def (0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x2 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0)  2015-09-24T22:53:31.360Z cpu9:33249)igu_sb_id(0x10)  igu_seg_id(0x0) pf_id(0x0)  vnic_id(0x0)  vf_id(0xff)  vf_valid (0x0) state(0x1)
  2015-09-24T22:53:31.360Z cpu9:33249)<3>bnx2x: [bnx2x_panic_dump:1150(vmnic0)]fp0: rx_bd_prod(0x3fd)  rx_bd_cons(0x0)  rx_comp_prod(0x40c)  rx_comp_cons(0x1)  *rx_cons_sb(0x1)
  2015-09-24T22:53:31.360Z cpu9:33249)<3>bnx2x: [bnx2x_panic_dump:1153(vmnic0)]     rx_sge_prod(0x0)  last_max_sge(0x0)  fp_hc_idx(0x1)
  2015-09-24T22:53:31.360Z cpu9:33249)<3>bnx2x: [bnx2x_panic_dump:1163(vmnic0)]fp0: tx_pkt_prod(0x152)  tx_pkt_cons(0x0)  tx_bd_prod(0x2a6)  tx_bd_cons(0x0)  *tx_cons_sb(0x0)
  

  I understand that the driver is broken. could not help me?

  Is this esxi 6.0 or later?  If so, it's a known issue. Please refer to KB KB VMware: ESXi 6.0 the network connectivity is lost with the NETDEV WATCHDOG timeouts in the vmkernel.log

  There is a workaround script in the KB.

• Configure the host of Serengeti

  Hey guys -.

  I get the following error message when you try to run the workflow "configure the host of Serengeti."

  I have BDE appliance 2.0 and 2.0 version of the plugin installed orchestrator

  [2015-03-02 16:24:19.006] [I] vShield Manager - Targe
  [2015-03-02 16:24:19.171] [I] https://10.69.255.184:8443/serengeti
  [2015-03-02 16:24:34.133] [I] REST host: DynamicWrapper (Instance) : [RESTHost]-[class com.vmware.o11n.plugin.rest.RESTHost] -- VALUE : com.vmware.o11n.plugin.rest.RESTHost@e8f027e0
  [2015-03-02 16:24:34.133] [I] REST host authentication: DynamicWrapper (Instance) : [RESTAuthentication]-[class com.vmware.o11n.plugin.rest.Authentication] -- VALUE : NONE
  [2015-03-02 16:24:34.184] [I] REST host added: DynamicWrapper (Instance) : [RESTHost]-[class com.vmware.o11n.plugin.rest.RESTHost] -- VALUE : com.vmware.o11n.plugin.rest.RESTHost@1f9746b
  [2015-03-02 16:24:34.318] [I] op: DynamicWrapper (Instance) : [RESTOperation]-[class com.vmware.o11n.plugin.rest.RESTOperation] -- VALUE : Login 452e4501-4ba7-4b47-81b1-c46716ca0210 /j_spring_security_check?j_username=YWRtaW5pc3RyYXRvckB2c3BoZXJlLmxvY2Fs&j_password=xxxxxxx POST 0 application/json
  [2015-03-02 16:24:34.318] [I] host: DynamicWrapper (Instance) : [RESTHost]-[class com.vmware.o11n.plugin.rest.RESTHost] -- VALUE : com.vmware.o11n.plugin.rest.RESTHost@f64b2fcb
  [2015-03-02 16:24:34.541] [I] vShield Manager - Targe
  [2015-03-02 16:24:34.546] [I] Serengeti
  [2015-03-02 16:24:34.662] [I] Login
  [2015-03-02 16:24:34.755] [I] Request: DynamicWrapper (Instance) : [RESTRequest]-[class com.vmware.o11n.plugin.rest.Request] -- VALUE : com.vmware.o11n.plugin.rest.Request@60986bab
  [2015-03-02 16:24:34.755] [I] Request URL: https://10.69.255.184:8443/serengeti/j_spring_security_check?j_username=YWRtaW5pc3RyYXRvckB2c3BoZXJlLmxvY2Fs&j_password=xxxxxx
  [2015-03-02 16:24:34.797] [I] Cannot execute request: hostname in certificate didn't match:  !=  (Workflow:Execute Login Operation / Execute Operation (item2)#14)
  [2015-03-02 16:24:34.898] [I] REST host removed: DynamicWrapper (Instance) : [RESTHost]-[class com.vmware.o11n.plugin.rest.RESTHost] -- VALUE : com.vmware.o11n.plugin.rest.RESTHost@79e5b22
  

  I would appreciate some advice from people who know what they are doing before you start poking around.

  Let me know if you need more information

  See you soon!

  Hi eatVM,

  You solved this problem?

  HTTP and REST of the vRO6.0 plugin added new more stringent audits.

  VMware has just released the version of technical overview of the vRO REST plugin with an option to disable checking of the host.

  So if you want to have BDE plugin works fine with vRA 6.2, you should spend the REST HTTP plugin.

  You can download the plugin here.

  Technical preview of REST plugin version

  Upgrade of the REST-HTTP 1.0.4.2229037 HTTP-REST 1.0.7 - 2563729 of vRO configuration web page.

  
  

  Make sure the value false for the parameter 'hostVerification' during execution workflow "Configuration of the host of Serengeti."

  
  

  Indulge yourself, hope everything goes well with you!

  
  

  Kind regards

  Sylvana

• Network cable unplugged, but I promise you that's not!

  I connect my computer to my Linksys router (this computer will not connect wirelessly).  Unfortunately, my computer thinks that the network cable is unplugged.  Let me give a few details before you continue!

  Router: Linksys WRT54GL v1.1, with the firmware update

  Ethernet card: Realtek PCIe GBE Family Controller (with up-to-date drivers)

  Computer OS: Windows 7 64-bit

  And now for the fun part.  First of all, I thought it was a bad ethernet cable, so I tried another and another still.  The cable doesn't seem to be the problem.

  Secondly, I thought it might well be my ethernet card.  I plugged the ethernet cable from my modem cable directly on my ethernet card and was instantly rewarded with a connection.  With this, I noticed that my ethernet card is not the problem.

  Third, I thought, well, it must be the router.  I tried all four ports on the back of the router to see if it was bad.  None of them worked.  The router shows not all lights for ports 1, 2, 3 or 4, regardless of where I plug. Progress!  Of course, it is the router, no?  In order to ensure, I ran a cable ethernet to the router to a laptop and has been awarded once more with a connection.  If the router is not the problem.

  After doing some reading here and abroad, I have reduced my 'speed and Duplex"to 10 Mbps half Duplex.  Who has not solved the problem.

  Any help would be immensely appreciated, because I'm quite frustrated.  Please let me know if I can provide more information for you.  Thank you in advance for your help!

  My friend is a very nice person and so is his first wife. I get along with two of them very well, but they have been quarreling all the time while they were married. They are now divorced and married to new partners and the two relations are developing.

  What this has to do with your problem? Well, your systematic troubleshooting effort eliminated all the simple causes of failure but it has not examined the issues of compatibility. I suspect that NETWORK card in your PC is just out of tolerance or is your router. Other devices can be a little more tolerant (as new friends partners), but together they won't work. How to test this? Here are a few options:

  (a) borrow a switch/router of different brand of a friend.

  (b) connect the two PCs on a switch that is not the same brand as your router, and then plug the switch on the router.

  Please post the result here!

• BlackBerry Smartphones on e-mail records

  When I created my email accounts, my BB only see the Inbox, none of the filtered messages are routed to another folder.  How do I change this?

  For example, in my Yahoo account, that filter messages in different folders.  Most of what strikes the Inbox is spam, I don't want to see.  How can I get my BB to show me the files and not the Inbox?

  Thank you

  You need BES to do, if you have only BIS, you cannot

• BlackBerry Smartphones Blackberry 8350i Nextel: question Word &amp; Sheet To Go (Standard Version). The whole Plan.

  New Member here (I got a new BlackBerry work a month ago) and this is my 1st Smartphone. The company that I work pays the entire Plan, but as we discovered everything really does mean everything! Professional email (Outlook) costs extra and Word To Go, Sheet To Go works best if you pay extra for the Premium Plan except that none of us can remove sheets, routing of telephone calls to my cost today of OnStar 20 cents a minute (used to be free and was a great security function-handsfree) and about 5 or 6 BlackBerry technicians and I can't seem to be able to even get the option of forwarding calls at work... and this is my second Blackberry in 4 weeks.

  I like the idea that I can now wear Excel spreadsheets with me which some with formulas. Problem is that every time a new version of one of the spreadsheets will be sent by e-mail to me so I try and delete the old, then download a new. I can't remove sheets of Excel spreadsheets or Word Documents.

  Someone told me that I can't remove spreadsheets or once their downloaded word documents. And he is paying extra for the Premium edition!

  Is this really true? Sounds crazy me finally fill the memory card then it's useless. The only cure for this that I have found is when I get an email with a Word Document attached or an attached Excel spreadsheet isn't absolutely download it, but save it in saved messages, which means that I won't be able to make a montage in the leaves.

  I love receiving e-mail, SMS, etc that I am usually on the road (all work related) but with what I stated above, I really wonder if it's really worth what we pay for the Plan and the purchase of BlackBerry.

  Can someone help me and prove me wrong? I would really appreciate it.

  Thank YOU, John

  Click the icon of your media, then click the MENU button and select Explorer

  Access your media card-blackberry-documents

  Highlight your excel sheet

  menu button-removal

• On the Question of VPN S2S source NAT

  Currently we have a number of implementation of VPN with various clients.  We are NAT'ing range them at a 24 in our network to keep simple routing, but we seek to NAT Source our resources due to security problems.  It is an example of a current virtual private network that we have configured:

  outside_map crypto card 5 corresponds to the address SAMPLE_cryptomap

  outside_map 5 peer set 99.99.99.99 crypto card

  card crypto outside_map 5 set ikev1 transform-set ESP-3DES-MD5 SHA-ESP-3DES

  card crypto outside_map 5 the value reverse-road

  SAMPLE_cryptomap list extended access permitted ip object-group APP_CLIENT_Hosts-group of objects CLIENT_Hosts

  NAT (inside, outside) static source APP_CLIENT_Hosts APP_CLIENT_Hosts CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source APP_CLIENT_Hosts APP_CLIENT_Hosts CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source APP_CLIENT_Hosts APP_CLIENT_Hosts CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  the APP_CLIENT_Hosts object-group network

  network-object, object SITE1_APP_JCAPS_Dev_VIP

  network-object, object SITE1_APP_JCAPS_Prod_VIP

  network-object, object SITE2_APP_JCAPS_Dev_Host

  network-object, object SITE2_APP_JCAPS_Prod_VIP

  network-object, object SITE1_APP_PACS_Primary

  network of the SITE1_APP_JCAPS_Dev_VIP object

  Home 10.200.125.32

  network of the SITE1_APP_JCAPS_Prod_VIP object

  Home 10.200.120.32

  network of the SITE2_APP_JCAPS_Dev_Host object

  Home 10.30.15.30

  network of the SITE2_APP_JCAPS_Prod_VIP object

  Home 10.30.10.32

  network of the SITE1_APP_PACS_Primary object

  Home 10.200.10.75

  network of the CLIENT_Host_1 object

  host of the object-Network 192.168.15.100

  network of the CLIENT_Host_2 object

  host of the object-Network 192.168.15.130

  network of the CLIENT_Host_3 object

  host of the object-Network 192.168.15.15

  network of the CLIENT_Host_1_NAT object

  host of the object-Network 10.200.192.31

  network of the CLIENT_Host_2_NAT object

  host of the object-Network 10.200.192.32

  network of the CLIENT_Host_3_NAT object

  host of the object-Network 10.200.192.33

  My question revolves around the Source NAT configuration.  If I understand correctly, I have to configure 3 statements of NAT per NAT Source since there are three different destinations that are NAT' ed.  I think I would need to add this:

  network of the SITE1_APP_JCAPS_Dev_VIP_NAT object

  Home 88.88.88.81

  network of the SITE1_APP_JCAPS_Prod_VIP_NAT object

  Home 88.88.88.82

  network of the SITE2_APP_JCAPS_Dev_Host_NAT object

  Home 88.88.88.83

  network of the SITE2_APP_JCAPS_Prod_VIP_NAT object

  Home 88.88.88.84

  network of the SITE1_APP_PACS_Primary_NAT object

  Home 88.88.88.85

  NAT (inside, outside) static source SITE1_APP_JCAPS_Dev_VIP SITE1_APP_JCAPS_Dev_VIP_NAT CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_JCAPS_Dev_VIP SITE1_APP_JCAPS_Dev_VIP_NAT CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_JCAPS_Dev_VIP SITE1_APP_JCAPS_Dev_VIP_NAT CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_JCAPS_Prod_VIP SITE1_APP_JCAPS_Prod_VIP_NAT CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_JCAPS_Prod_VIP SITE1_APP_JCAPS_Prod_VIP_NAT CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_JCAPS_Prod_VIP SITE1_APP_JCAPS_Prod_VIP_NAT CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE2_APP_JCAPS_Dev_Host SITE2_APP_JCAPS_Dev_Host_NAT CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE2_APP_JCAPS_Dev_Host SITE2_APP_JCAPS_Dev_Host_NAT CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE2_APP_JCAPS_Dev_Host SITE2_APP_JCAPS_Dev_Host_NAT CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE2_APP_JCAPS_Prod_VIP SITE2_APP_JCAPS_Prod_VIP_NAT CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE2_APP_JCAPS_Prod_VIP SITE2_APP_JCAPS_Prod_VIP_NAT CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE2_APP_JCAPS_Prod_VIP SITE2_APP_JCAPS_Prod_VIP_NAT CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_PACS_Primary SITE1_APP_PACS_Primary_NAT CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_PACS_Primary SITE1_APP_PACS_Primary_NAT CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  NAT (inside, outside) static source SITE1_APP_PACS_Primary SITE1_APP_PACS_Primary_NAT CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  Is that correct, or is at - it an easier way to do this without having to add all statements of NAT?  Moreover, any change would be to do on the access list?

  Hello

  To my knowledge you should not create several new instructions from NAT. You should be well just create a new Group 'object' for new addresses your source address NAT.

  To better explain, take a look at your current ' object-group ' that defines your source addresses

  the APP_CLIENT_Hosts object-group network

  network-object, object SITE1_APP_JCAPS_Dev_VIP

  network-object, object SITE1_APP_JCAPS_Prod_VIP

  network-object, object SITE2_APP_JCAPS_Dev_Host

  network-object, object SITE2_APP_JCAPS_Prod_VIP

  network-object, object SITE1_APP_PACS_Primary

  Now you can do this sets up a "object-group" that contains a NAT IP address for each of the IP addresses inside the ' object-group ' and 'object' used above. The IMPORTANT thing is that the ' object-group ' that contains the NAT IP addresses is in the SAME ORDER as the actual source addresses.

  I mean, this is the first IP address is in most object - group ' will correspond to the first IP address in the newly created "object-group" for the IP NAT addresses.

  As above, you can simply have the same "nat" configurations 3 as before but you change/add in the newly created "object-group"

  For example, you might do the following

  network of the SITE1_APP_JCAPS_Dev_VIP_NAT object

  Home 88.88.88.81

  network of the SITE1_APP_JCAPS_Prod_VIP_NAT object

  Home 88.88.88.82

  network of the SITE2_APP_JCAPS_Dev_Host_NAT object

  Home 88.88.88.83

  network of the SITE2_APP_JCAPS_Prod_VIP_NAT object

  Home 88.88.88.84

  network of the SITE1_APP_PACS_Primary_NAT object

  Home 88.88.88.85

  the APP_CLIENT_Hosts_NAT object-group network

  network-object, object SITE1_APP_JCAPS_Dev_VIP_NAT

  network-object, object SITE1_APP_JCAPS_Prod_VIP_NAT

  network-object, object SITE2_APP_JCAPS_Dev_Host_NAT

  network-object, object SITE2_APP_JCAPS_Prod_VIP_NAT

  network-object, object SITE1_APP_PACS_Primary_NAT

  Then you add the following configurations of "nat"

  NAT (inside, outside) 1 static source APP_CLIENT_Hosts APP_CLIENT_Hosts_NAT CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  Static NAT APP_CLIENT_Hosts APP_CLIENT_Hosts_NAT static destination CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of source route 2 (inside, outside)

  NAT 3 (indoor, outdoor) static source APP_CLIENT_Hosts APP_CLIENT_Hosts_NAT CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  Note line numbers, we added the above commands. This allows them to enter the upper part of the ASAs NAT rules, and therefore, they will become active immediately. Without line numbers that they will only be used after when you remove the old lines.

  Then you can remove the "old"

  no nat source (indoor, outdoor) public static APP_CLIENT_Hosts APP_CLIENT_Hosts CLIENT_Host_1_NAT CLIENT_Host_1 non-proxy-arp-search of route static destination

  no nat source (indoor, outdoor) public static APP_CLIENT_Hosts APP_CLIENT_Hosts CLIENT_Host_2_NAT CLIENT_Host_2 non-proxy-arp-search of route static destination

  no nat source (indoor, outdoor) public static APP_CLIENT_Hosts APP_CLIENT_Hosts CLIENT_Host_3_NAT CLIENT_Host_3 non-proxy-arp-search of route static destination

  This should leave you with 3 configurations "nat" who made the NAT source addresses and destination.

  Naturally while you perform this change you will also have to change the ACL Crypto to match the new source NAT. This is because as all NAT is done before any VPN on the ASA. So the destination addresses are Nations United for before VPN and source addresses are translated before VPN.

  If you do not want to make the changes without affecting the connections too so I suggest

  • Add rules to the ACL Crypto for new addresses (NAT) source. Of course, this must be done on both sides of the VPN L2L. You would still be leaving the original configurations to the Crypto ACL does not not the functioning of the L2L VPN.
  • Add new configurations of "nat" above without the line numbers I mentioned who mean you that they wont be used until you remove the "old".
  • When you are ready to be migrated to use the new IP addresses, simply remove the original "nat" configurations and the ASA will start the corresponding traffic for new "nat" configurations. Provided of course that there is no other "nat" configuration before the nine that could mess things up. This should be verified by the person making the changes.

  Of course if you can afford a small cut when then changing the order in which you do things should not matter that much. In my work, that connections are usually not that critical that you can't make these changes almost at any point as it is a matter of minutes what it takes to make changes.

  Hope this made sense and helped

  Remember to mark a reply as the answer if it answered your question.

  Feel free to ask more if necessary.

  -Jouni

• sparse mode multicast edge WAN router

  Hi all

  I hope you well. I have a problem of multicast and I was wondering if anyone can help. We have several remote sites connected to the router end hub and some sites are unable to receive multicast streams. We use the pim sparse mode with RP static. whenever I try to do a ping to a lan switch multicast stream I get

  (*, G) entry with correct PR, RPF nbr and the incoming interface on LHR but oil mill interface iam get none. on the last jump (LHR) router I see interface OIL as pointing as the igmp join query comes from LAN to lan.

  I see (ip lan of the CBC, G) entry in the table mrouting but interface new entrant is pointing to lan, no details of PR and outbound interface is WAN.

  can you advise or point iin right direction. Thank you

  concerning

  M

  You will see that because the switch acts as a source for a stream multicasting if your WAN router it records correctly.

  If you try to troubleshoot multicast on the remote receiver then the above is not a valid test and tells you nothing.

  What is the address of muilticast group you are trying to reach the remote site?

  That shows the mroute for this group address table?

  Jon

• Vulnerability CVE-2015-7547 glibc on SRA series

  Glibc recently patched vulnerability (CVE-2015-7547) apply to the SRA series products? See

  Hi Teemup,

  Here is the official information related this vulnerability

  https://support.software.Dell.com/product-notification/187642?ProductName=SonicWALL%20SRA%20Series

  Ben D
  Reference Dell SonicWall
  #Iwork4Dell