waited for the parent session complete

Similar Questions

• Start stuck on "Please wait for the Local Session Manager."

  I would say that this problem started a couple of days. Went to start my laptop (Toshiba) and he sat on the "Please wait" message forever.

  Had no problems to start in safe mode. Looked up various ways of addressing the problem.

  Was able to change the resume date and back a few weeks ago. Still no luck. Happened to read something on a printer Epson being perhaps the problem driver (it was installed a day before the date of restoration chosen). Uninstalled the drivers, computer still does not start.

  Tried restarting running. I do not have the CD it came with Vista, but it was an option when you hold F8 during startup (I think?) Couldn't find any problems.

  Ran check on memory. No problem either.

  Changed settings for a verbose startup and ran a Diagnostic startup - all good for this. Then tried selective startup load system services... This is when the error occurs. When starting, it hangs on "Please wait for the Local Session Manager" and does nothing more.

  I looked in the event viewer to see what came that time and a couple mistakes were:

  Event ID 6000: winlogon notification subscriber was unavailable to handle a notification event.

  Event ID 7026: the next (s) start or start failed to load system
  spldr
  Wanarpv6

  It would be very useful for me not having to run my computer in safe mode automatically all the time, although it is useful that I at least have that option. Any help is greatly appreciated.

  Hello

  1. by chance your computer is connected to a domain environment?

  2. as you mentioned in your article that you tried the selective startup, I want to confirm if you have disabled the services left 3rd after hide Microsoft services?

  If you did not disable these services make sure you disable and then check if it works.
  See the article below for more information.
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 in the above article.

  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• VMware-vim-cmd: waiting for orders to be completed?

  Hi all, I adapt a backup script I made for VMware Server 1.x to VMware Server 2.x and I'm having trouble doing ordinary things like 'suspend' or "create a snapshot" "a VM from starting.

  There are several ways to do the same thing in a certain way does not require any authentication, others indeed require authentication, for example, to create a snapshot, you can:

  VMware-vim-cmd vmsvc/snapshot.create 'id of the virtual machine.

  or

  vmrun-h https://127.0.0.1:8333 / sdk u user-p password of snapshot "[datastore] /vm_path/vmx_name.vmx '

  The problem with vmware-vim-cmd approach is that it does not wait for the command to complete, and is not a welcome feature in a script.

  Instead, the vmrun command wait until the end, but to use it in a script, you must also include the identification of the user and password information in the script, and it is not welcome.

  So the question (as shown in the topic) is: is it possible to make orders of vim-vmware-cmd to wait until the end?

  If someone knows how to do that I would be very grateful

  Thank you for reading,

  10nico

  The vimsh and the vimsh wrapper vmware-vim-cmd is not officially supported by VMware, that being said, I agree that it should allow you to check the situation, etc. It can be a pro/con and depending on how the call command, the wrappers actually communicate to the VI API server, and if you look at the VI API there are all both blocking and non call.

  Vmware-vim-cmd, the command is executed and returns to the shell for most. You might be able to monitor the tasks that is created and ensure that it is completed, but I have not played too much with it.

  [root@himalaya scripts]# vmware-vim-cmd vimsvc
  Commands available under vimsvc/:
  auth/             login             task_cancel       task_list
  connect           logout            task_description
  license           property_dump     task_info
  

  Again, these are undocumented, unsupported and the behavior will vary =)

  I advise to use the VI API (Powershell or VI Perl Toolkit) to accomplish your tasks, and you can even take a look at some of the utilities that are available with the VI Perl Toolkit Utilities: http://www.vmware.com/support/developer/viperltoolkit/viperl15/doc/perl_toolkit_utilities_idx.html

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  http://Twitter.com/lamw

  If you find this information useful, please give points to "correct" or "useful".

• Wait for the entry?

  Hi all
  
  I need to create a custom entry dialog box and the problem I encountered is that I can't figure out how to make my request to wait for the user to complete the entries in the framework. When you use a JDialog or JOptionPane application will stop running and wait for the dialog box to close. My question is how to do something similar without using a JOptionPane or JDialog. I just can't figure out how to get the same effect by using a JFrame or other component. I know I could just use a JDialog or JOptionPane to get input from the user, but I'm just curious to know how I can stop running and wait for the entry as the JOptionPane allows you to do, but without using a JOptionPane or JDialog.
  
  Thank you for your help :)
  Nathan D.
  
  -----
  : Edit:
  I forgot to mention that the reason main I avoids JDialogs is I need the entry dialog box to be internal not external application I use mode exclusive fullscreen. And a JOptionPane does not allow me to add the other components too it such as JLabels and other GUI. I just need a way to get input from a component or internal window and wait for the entry as a JOptionPane or JDialog.
  -----
  
  A NBS are:
  
  

  import java.awt.event.*;
  import java.awt.*;
  import javax.swing.*;
  
  
  
  public class Main extends JFrame implements ActionListener {
  
      /**
       * @param args the command line arguments
       */
      public static void main(String[] args) {
          new Main();
      }
  
  
      JButton go = new JButton("Show custom input dialog");
  
      public Main() {
          setSize(300,150);
          setLocationRelativeTo(null);
          setLayout(new FlowLayout());
          go.addActionListener(this);
          add(go);
          setVisible(true);
      }
  
      public void actionPerformed(ActionEvent e) {
          InputDialog d = new InputDialog();
  
          /*
           * Here is the problem it is necessary that I create a
           * custom input dialog to allow further modifications however
           * i'm not sure how to wait for the user to enter text and press
           * continue in that input dialog. Unlike JOptionPane the code executes
           * before the user presses continue. My question is how do I wait for the user
           * to press continue in the InputDialog before I call d.getString(); without making the main
           * application unresponsive.
           */
  
          String returnValue = d.getString();
          System.out.println("return value "+returnValue); //will be null or empty because application doesn't wait for input.
      }
  
  
      class InputDialog extends JFrame implements ActionListener {
          JTextField f = new JTextField();
          JButton go = new JButton("Continue");
  
          public InputDialog() {
              setTitle("Custom Input Dialog");
              setSize(300,150);
              setLocationRelativeTo(null);
              setLayout(new FlowLayout());
              f.setPreferredSize(new Dimension(100,25));
              go.addActionListener(this);
              add(f);
              add(go);
              setVisible(true);
          }
  
          public void actionPerformed(ActionEvent e) {
  
          }
  
          public String getString() {
              return f.getText();
          }
      }
  }

  Published by: neptune692 on January 3, 2011 13:25

  neptune692 wrote:
  .. a JOptionPane does not allow me to add the other components too it such as JLabels and other GUI. ..

  Of course, it does!

  import java.awt.event.*;
  import java.awt.*;
  import javax.swing.*;
  
  public class DumbNameMain extends JFrame implements ActionListener {
  
      /**
       * @param args the command line arguments
       */
      public static void main(String[] args) {
          new DumbNameMain();
      }
  
      JButton go = new JButton("Show custom input dialog");
  
      public DumbNameMain() {
          setSize(300,150);
          setLocationRelativeTo(null);
          setLayout(new FlowLayout());
          go.addActionListener(this);
          add(go);
          setVisible(true);
      }
  
      public void actionPerformed(ActionEvent e) {
          JTextField f = new JTextField(10);
          JButton go = new JButton("Continue");
          JPanel p = new JPanel(new FlowLayout());
          p.add(f);
          p.add(go);
          JOptionPane.showMessageDialog( this, p );
  
          String returnValue = f.getText();
          System.out.println("return value "+returnValue);
      }
  }
  

• waiting for the task to be completed

  I inherited a program that tests a hardware device extensively.  A test turns or several times each channel of AI and bed the waveform of channel I.  I use a card PXI-6229 DAQ with c# .NET.  The program is suspended in the while loop, wait until the task is complete. This is the code:

  public bool TestThisChannel (object nullObject) {}
  Double coversionFactor;
  String name;
  String Description;
  _PXI6229_SLOT12.getChannelInfo ((int) nullObject, name, coversionFactor, to the Description);
  _PXI6229_SLOT12. StartAnalogInput6s (Name);
  for (int i = 0; i)< 5;="" i++)="" {="" 5="">
  _PXIChassis.SetPowerRelayOn (null);
  _PXIChassis.Wait500ms (null);
  _PXIChassis.SetPowerRelayOff (null);
  _PXIChassis.Wait500ms (null);
  }
             
  While {(_PXI6229_SLOT12.runningTask!=null)}
  } //Wait task is completed

  AnalogMultipleInputTask private task;
  runningTask of public work;
  private AsyncCallback analogCallback;
  Private AnalogMultiChannelReader analogInReader;
  public AnalogWaveformdata;

  Public Sub StartAnalogInput6s (string AIChannel)
  {
  Create a new task
  try {}
  AnalogMultipleInputTask = new Task();

  Create a virtual channel
  AnalogMultipleInputTask.AIChannels.CreateVoltageChannel (AIChannel, "",)
  (AITerminalConfiguration) (-1),-10, 10, AIVoltageUnits.Volts);

  Configure synchronization settings
                 
  AnalogMultipleInputTask.Timing.ConfigureSampleClock ("", 100000, SampleClockActiveEdge.Rising, SampleQuantityMode.ContinuousSamples, 600000);
                 
  Check the task
  AnalogMultipleInputTask.Control (TaskAction.Verify);

  Prepare the table for the data
  runningTask = AnalogMultipleInputTask;
  analogInReader = new AnalogMultiChannelReader (AnalogMultipleInputTask.Stream);
  analogCallback = new AsyncCallback (EndAnalogInput);

  For .NET Framework 2.0 or a later version, use SynchronizeCallbacks to specify that the object
  Marshals the callbacks on the appropriate threads.
  analogInReader.SynchronizeCallbacks = true;
  analogInReader.BeginReadWaveform (600000, analogCallback, AnalogMultipleInputTask);
  } catch (Exception exception) {}
  MessageBox.Show (exception. (Message);
  runningTask = null;
  AnalogMultipleInputTask.Dispose ();
  }
  }

  public void EndAnalogInput (IAsyncResult ar)
  {
  Try
  {
  If (runningTask is ATR AsyncState)
  {
  Read the data of the channels
  data = analogInReader.EndReadWaveform (ar);
  }
  }
  catch (System.exception DaqException)
  {
  Display errors
  MessageBox.Show (exception. (Message);
  runningTask = null;

  AnalogMultipleInputTask.Dispose ();
  }
  }

  Any help will be appreciated.

  Thank you

  Howard

  Thanks Mason. You got me thinking on the right track.  I made a few changes based on an example I found of NOR.  I changed analogInReader.BeginReadWaveform (...) of data = analogInReader.ReadWaveform (600000) and I changed the while (_PXI6229_SLOT12.runningTask! = null) {} to _PXI6229_SLOT12.runningTask.WaitUntilDone () and it seems to work fine.

  Thanks for your help.

  Howard

• CREATE INDEXES online is waiting for the TX = 4 mode

  Hello

  I have a strange blocking problem where an INDEX CREATE LINE is waiting for a transaction that did only inserted a line in the parent table.

  Wait is mode TX = 4 (not TM locks) and I currently have it reproduced only on 11.2.0.3 and 11.2.0.4

  Easy to replicate the schema SCOTT:

  Session 1:

  SQL > set time on

  14:54:58 SQL > insert into SCOTT. Dept (DEPTNO, dname) values (50, 'test');

  1 line of creation.

  Session 2;

  14:55:24 SQL > create index test on SCOTT. EMP (ename) online;

  It's waiting ' enq: TX - line lock conflict ":"

  SQL > select sid, chain_signature from v$ wait_chains where blocker_is_valid = 'TRUE '.

  SID CHAIN_SIGNATURE

  ---------- ----------------------------------------------------------------------

  603 ' SQL * Net client message' < ='enq: TX - line lock conflict '

  While waiting to acquire the lock of transaction in mode 4:

  SQL > select * lock gv$ where sid = 603

  INST_ID SELECT ADDR KADDR SID TYPE ID1 ID2 LMODE CTIME BLOCK REQUEST

  ---------- ---------------- ---------------- ---------- ---- ---------- ---------- ---------- ---------- ---------- ----------

  1 00000006CDA05EB8 00000006CDA05F10 603 352577 0 4 0 348 2 AE

  1 00000006CDA06078 00000006CDA060D0 603 DL 779505 0 3 0 308 2

  1 00000006CD9FABE0 00000006CD9FAC38 603 DL 779505 0 3 0 308 2

  1 00007F28001F5028 00007F28001F5088 603 779505 0 2 0 308 2 TM

  1 00007F28001F5028 00007F28001F5088 603 779510 0 4 0 308 2 TM

  1 00000006CD9FA240 00000006CD9FA298 603 779505 0 4 0 308 2 OD

  1 00000006B4F26790 00000006B4F26808 589847 711499 6 0 308 2 TX 603

  1 00000006CDA0ED68 00000006CDA0EDC0 655377 996169 0 4 308 TX 603 0

  I've traced 10046 and 10704:

  broadcast message = obj 29231196672 #= 779514 tim = 1447251053634045

  ksqgtl * mode TX-000f001e-000ad97c = 4 flags = 0 x 10001 timeout = 21474836 *.

  ksqgtl: xcb = 0x6bb322528, ktcdix = 2147483647, topxcb = 0x6bb322528

  ktcipt (topxcb) = 0 x 0

  ksucti: init logon has of txn DID:

  ksqgtl:

  ksqlkdid: 0001-003F-0000AFC4

  ksudidTrace: ksqgtl

  ktcmydid(): 0001-003F-0000AFC4

  ksusesdi: 0001-003F-0000AFC3

  ksusetxn: 0001-003F-0000AFC4

  ksqcmi: TX, f001e, ad97c mode = 4 timeout = 21474836

  2015-11-11 15:11:36.566

  WAITING #140700792578680: nam ='enq: TX - line lock conflict ' ela 42932082 name = | mode = 1415053316 usn < < 16 | location = sequence 983070 = obj 711036 #= 779514 tim = 1447251096566283

  And there is nothing in V$ SESSION leader/block/line current. class obj # is EMP. current sql_id is the CREATE INDEX.

  If anyone has an idea on:

  -Why creating an index in line must wait for transactions that modified only parent table

  -How to continue the investigation

  -can or cannot reproduce in other versions

  Thanks in advance,

  Franck.

  I guess you have a constraint foreign key between emp and Dept.

  It's expected behaviours: since 11.1 any DML at one end of a referential integrity constraint translates into a mode lock 3 taken at the other end, and your phenomenon resembles a side effect of this.

  When you try to create the index online that your session must assume that the other session (holding mode 3 on the emp and dept) may have changed the emp and dept, so it must wait for the session to the commit or rollback.

  (I guess that in principle, he could walk the cancellation of the transaction see if EMP had in fact been changed - but maybe who was considered too complicated to be worth the risk to implement)

  Concerning

  Jonathan Lewis

  Updated - I just did a quick check to reproduce the effect on 11.1.0.7

  For reference - here are a few notes on modes of locking and how the application has changed over time: https://jonathanlewis.wordpress.com/2010/06/21/locks/

• Wait for the event begins with SQL * Net message from client-time wait 178577 units

  Hello
  
  I'm watching events waiting for a request from long time in TOAD.
  I start the query on an instance of TOAD, and open the browser to log on to another instance.
  But I am surprised to see that in "TOtal expected" on the RIGHT part->
  SQL * Net message from client is the longest time and is already - > 178577 units while I just to start the query.
  
  Considering that, in the current waiting she shows DB file scattered read correctly for a few seconds.
  
  Please suggest.

  user8941550 wrote:
  Hello. No explanation for this... :-(

  Hello

  people work here, you don't know?
  I think Tom Kyte explains it well enough. This wait event is linked to your session database waiting for the guest to say to do something.

  So it is not related to the database, but to your application.
  Also as it is a wait of session event you might have had your session inactive for some time (do nothing)

  If you want to check the waiting events correctly I suggest using tkprof and start a new session in SQL more as shown by Tom Kyte in the link I posted.

  Then, run your query in sqlplus setting track and pull it out as soon as your statement is completed.
  that is to say:

  -- myest.sql
  alter session set events '10046 trace name context forever, level 12';
  SELECT ... -- your query here
  exit
  

  Run in sqlplus in this way:

  sqlplus user/password@db @mytest.sql
  

  Then check with tkprof.

  Kind regards.
  Al

• Storage VMotion - a general error occurred: could not wait for the data.  Error bad0007.

  People,

  I searched through this forum and have not found an answer that works in many positions out there, I say to myself that I would ask him once again.

  Here's the context:

  We have 12 identical Dell M600 blades in 2 chassis with 16 GB of Ram, 2 x Xeon E5430, they are all connected to an Equallogic PS 5000XV iSCSI SAN on a separate iSCSI (vswitch1) with 2 cards network dedicated network and dedicated switch, console svc iscsi dedicated, dedicated VMkernel port for iscsi access. Net access (vswitch0) contains port groups VM for our various networks and a console port and vmkernel svc for VMotion with 2 separate NETWORK cards as well.

  We are running ESX 3.5 U3 and VCenter 2.5 U3 on Win2k3 R2

  VMotion works between all servers, Storage Vmotion works for most machines, HA works and the value 2 host failurs with no monitoring of vm, DRS is set to manual for now I have a few machines on the local stores that I complete my rebuilt LUN, there is no set of rules for DRS and VMware EVC is enabled for guests of the Intel. However, I'll just describe one machine to do svmotion below.

  Here's the problem:

  I'm trying to Svmotion via svmotion.pl - interactive, a Machine to Windows 2000 with a virtual disk and a virtual RDM. I am aware of the requirements for the RDM and required parameters for svmotion, independent is not selected for the RDM, and I also have svmotioned several machines linux and win2k3 with the same configuration without problem. In the interactive session, I choose to individually place the disks and I chose the virtual disk to only the virtual machine to be moved, essentially, as I saw it move vdisk virtual machine and then copy to the pointer of the RDM.

  The use of the processor in this machine is about 25% average. but I try to run migrations at the time the lowest. and The Host it itself shows only about 5.5 GB of the 16 GB of RAM used. so I think we're good on the RAM. the volume/datastore that I'm migrating from has 485 GB free and the volume/datastore I migration towards a 145 GB free. the VM virtual disk is only about 33 GB.

  I run the script the windows version of the RCLI svmotion. and when to begin the process, I get the following error at around 2 percent of the progress:

  "Since the server has encountered an error: a general error occurred: could not wait for the data."  Error bad0007. Invalid parameter. »

  After searching around, I found the following hotfixes to the U2 release notes

  • Migrate.PageInTimeoutResetOnProgress: Set the value to 1.

  • Migrate.PageInProgress: The value 30, if you get an error even after the setting of the Migrate.PageInTimeoutResetOnProgress variable.

  I've made these changes, and I still get the same error.

  When I dig in the newspaper, I see these entries in the journal of vmkwarning:

  (Feb 24 00:17:32 vmkernel iq-virt-c2-b6: 82:04:13:56.794 cpu4:1394) WARNING: bunch: 1397: migHeap0 already at its maximumSize bunch. Cannot extend.

  (Feb 24 00:17:32 vmkernel iq-virt-c2-b6: 82:04:13:56.794 cpu4:1394) WARNING: bunch: 1522: Heap_Align (migHeap0, 1030120338/1030120338 bytes, 4 align) failed.  calling: 0x988f61

  (Feb 24 00:17:32 vmkernel iq-virt-c2-b6: 82:04:13:56.794 cpu4:1394) WARNING: migrate: 1243: 1235452646235015: failure: out of memory (0xbad0014) @0x98da8b

  (Feb 24 00:17:32 vmkernel iq-virt-c2-b6: 82:04:13:56.794 cpu2:1395) WARNING: MigrateNet: 309: 1235452646235015: 5 - 0xa023818: sent only 4096 bytes of data in message 0: Broken pipe

  (Feb 24 00:17:32 vmkernel iq-virt-c2-b6: 82:04:13:56.794 cpu6:1396) WARNING: migrate: 1243: 1235452646235015: failed: Migration protocol error (0xbad003e) @0x98da8b

  (Feb 24 00:17:32 vmkernel iq-virt-c2-b6: 82:04:13:56.794 cpu2:1395) WARNING: migrate: 6776: 1235452646235015: could not send data for 56486: Broken pipe

  At this point, I'm stuck... What is Windows RCLI? the vcenter Server? or the service console with not enough of RAM? We have already increased all our consoles service 512 MB...

  Any help would be greatly appreciated...

  Thanks in advance.

  Alvin

  The vmkernel on out of memory error, I had that before. And vmware support recommends setting 800M Max service console memory. And I did it and have no problems after that.

  See if that helps the issue.

  Mike

• remote desktop hang at 'Please wait for the system event notification' during logoff

  When I disconnect a remote connection, sometimes the GET logoff screen stuck at "Please wait for the system event notification" next time I try to open a session.
  This can also happen if that I disconnect the user, but the user seems to weigh on this same screen as well.

  There is a particular difficulty for this?  I can connect as long as administrator to another account, I can't kill connection attached somehow to be registered in the next time?

  Thank you

  Hello

  I suggest you to take a look at the answer in this thread and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/Sens-could-not-connect-to-the-system-event/4e5a04e9-88f8-4017-9416-2ca67c5ce7c5

  Hope this helps,

• Please wait for the customer to political group - stop questions

  Hello

  I have problems with the closing of a machine. When the machine is connected to the corporate network, everything works fine. However, if the computer is connected to the VPN (1 hour or more) it is always suspended when it stops. First step in the shutdown process is:

  Please wait for the system event Notification service.

  This change after 3 minutes exactly. Next step:

  Please wait for Group Policy client windows 7

  is never exceeded (even after a few hours). Machine never off.

  Under newspapers there are always these 4 events when the machine stops in vain:

  1. 6005: the winlogon notification subscriber takes a long time to handle the notification event (Logoff).
  2. 4627: the event COM + a system expired attempt to fire the method of logging on the event {D5978650-5B9F-11D1-8DD2-00AA004ABD5E} class for the Publisher and the Subscriber.  The Subscriber has not responded within 180 seconds. The full name of the subscription is "ISensLogon2". The HRESULT is 80010002
  3. 6006: the winlogon notification subscriber took 180 second (s) to handle the notification event (Logoff).
  4. 6005: the winlogon notification subscriber takes a long time to handle the notification event (Logoff).

  Sense has expired after 3 minutes while there is no event 6006 for GPClient and machine is stuck there for centuries (Please wait for the customer to group policy). I noticed in the system logs that before the machine hangs during the shutdown process there are these errors and warnings:

  • 5783: the session configuration for the Windows NT or Windows 2000 Domain Controller \\server for the domain X is not admissible.  The current CPP of Netlogon call on \\machine to \\server was canceled.
  • 1014: name resolution for the name of the server has expired after none of the configured DNS servers answered.
  • 131: NtpClient could not set a domain peer to use as a source of time due to the DNS resolution error on ". NtpClient will try again in 3473457 minutes and double the reattempt interval thereafter. The error was: the requested name is valid, but no data of the requested type was found. (0x80072AFC).

  There is more than 1014 events for different servers and some 131. 5783 is always alone.

  I did a group policy log, because I thought that I will be able to see where the machine stuck. Below you can see the part of the newspaper GPSVC when the machine stops in vain:

  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: incoming with the event 0xe58
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: cancellation pending appeals
  GPSVC (2d4.1cfc) 21:31:24:327 Client_CompleteNotificationCall: failed with 0x71a
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: cancelled waiting for calls
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: dating dwStatus = 0 x 0
  GPSVC (438.1a04) 21:31:24:327 waiting for user group wire political end.
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: incoming with the event 0xe10
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: cancellation pending appeals
  GPSVC (218.C88) 21:31:24:327 Client_CompleteNotificationCall: failed with 0 x 525
  GPSVC (2d4.1cfc) 21:31:24:327 Client_CompleteNotificationCall: failed with 0x71a
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: cancelled waiting for calls
  GPSVC (2d4.9C8) 21:31:24:327 CGPNotify::OnNotificationTriggered: Completenotification failed with 1317
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: incoming with the event 0xdcc
  GPSVC (218.1054) 21:31:24:327 CGPNotify::UnregisterNotification: incoming with the event 0x20cc
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (2d4.9C8) 21:31:24:327 CGPNotify::OnNotificationTriggered: Completenotification failed with 1317
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::UnregisterNotification: incoming with the event 0xd90
  GPSVC (218.1054) 21:31:24:327 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (2d4.1cfc) 21:31:24:327 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (2d4.1cfc) 21:31:24:342 CGPNotify::UnregisterNotification: dating dwStatus = 0 x 0
  GPSVC (218.D48) 21:31:24:342 Client_CompleteNotificationCall: failed with 0 x 525
  GPSVC (218.D48) 21:31:24:342 CGPNotify::OnNotificationTriggered: Completenotification failed with 1317
  GPSVC (218.1c04) 21:31:24:327 Client_CompleteNotificationCall: failed with 0 x 525
  GPSVC (218.1c04) 21:31:24:342 CGPNotify::OnNotificationTriggered: Completenotification failed with 1317
  GPSVC (218.1054) 21:31:24:342 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (218.1054) 21:31:24:342 CGPNotify::UnregisterNotification: dating dwStatus = 0 x 0
  GPSVC (218.1054) 21:31:24:342 CGPNotify::UnregisterNotification: entering with the event 0 x 2100
  GPSVC (218.1054) 21:31:24:342 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (218.1054) 21:31:24:342 CGPNotify::UnregisterNotification: dating dwStatus = 0 x 0
  GPSVC (218.1054) 21:31:24:342 CGPNotify::UnregisterNotification: entering with the event 0 x 1264
  GPSVC (218.1054) 21:31:24:342 CGPNotify::AbortAsyncRegistration: No asynchronous recording is in progress
  GPSVC (218.1054) 21:31:24:342 CGPNotify::UnregisterNotification: dating dwStatus = 0 x 0

  I excluded 1 GP machine and left on the VPN for a few hours, several times. He always stopped correctly.

  However I tried with the VPN disconnection before turning off the machine, I even turned off WiFi but machine still hanging. If I tried to get GP results it takes ages before stopping the machine and he's stuck in the step "to get the user name. Gpupdate/force will never update policy (it stops at policy update...). I tired with the installation of different patches that has not solved the problem.

  I think that there is that DNS issues while the machine is on VPN which led the GP cannot be applied. When the machine tries to close it is always somehow connected. There is no problem with the connection, no GP application script when the user disconnects, not roaming profiles.

  Does anyone have the same problems? All machines are Dell with Juniper NC (VPN).

  Thank you

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  TechNet forum: For Windows 7 

  Hope this information helps.

• Script to wait for Clone task is completed

  Good day, as part of the post, I run a command that enables the NIC and sets the right Port-Group of cloning process. I put a sleep command in each environment is diferrent, so I find myself always change this duration of sleep because the cloning process does not end in the time of sleep and the rest of the script fails. So in order to get rid of the sleep control that I want to capture the CloneVM_Task and pass this parameter to wait-task that will force the completion of the ClonVM_Task. I could just make sure no other tasks are running but this task, but as we all know that alays can't be the case. So that's what I did.

  I begin a deployment of FVO to have an another long running task. Then I run the script.

  If ((Get - PSSnapin - name Vmware.VimAutomation.Core - ErrorAction SilentlyContinue) - eq $null) {Add-PSSnapin "Vmware.VimAutomation.Core"}

  # Virtual Center details
  $server_address = "MYvCenter name" or IP

  SE connect-VIServer-Server $server_Address - user username-pass password - WarningAction SilentlyContinue

  
  #Create Master VM Templates
  #
  # Here we import the CSV file with the account information and he piped in a Foreach-object
  # Creating a Variable that imports the csv file that contains all data of the virtual machine

  CD "e:\Scripts.
  $InputFile = import-Csv "E:\scripts\mycloneinput.csv".
  $InputFile | {ForEach-Object

  $ip = $_. VM_IPAddress
  $GName = $_. VM_Guestname
  $TName = $_. Template_name
  $HName = get-VMHost "myhostname" # 1 first Select
  $Desc = $_. Description
  $Dstore = $_. Datastore_Name
  $Spec = $_. Customization
  $Folder = $_. Folder
  $Sfolder = $_. Subfolder
  $NIC = $_. NIC
  $NIC_Lable = $_. NIC_Label
  $Gateway = $_. NIC_Gateway
  $SubnetMask = "255.255.255.0".
  $DNS1 = $_. DNS1
  $DNS2 = $_. DNS2
  
  Write-host "creation: ' $GName
  Write-host "template name is: ' $TName

  # This takes variables and creates the virtual machine
  Get-OSCustomizationSpec $Spec | Get-OSCustomizationNicMapping | »
  Game-OSCustomizationNicMapping - IpMode UseStaticIP - $ip - $SubnetMask subnet mask - DNS IpAddress $DNS1, $DNS2 - DefaultGateway $Gateway
  New-VM-name $GName - location $Folder - model $TName - host $HName - $Dstore - $Desc Description data store - OSCustomizationSpec $Spec - RunAsync-confirm: $false
  
  #######################################
  #Waiting for cloning process to finish.
  #######################################

  $$$ Under notes show a little history of how I got to this point.

  $$ Note1: the first attempt, I just captured running tasks and their past to the task pending. "Well, since the deploy OVF and ClonVM_Task where it runs would wait up to two when completed by the end."

  $$ Note2: so I added the If Else loop below that failed, because $RTask never equaled only CloneVM_Task, but was a table of two.

  $$ Note3: I tried to us below to separate the two tasks to help

  # $RTask = get-task-status running (who captured the two tasks running)

  # $Array = $Rtask.Split("") (Errored with the method call failed because [System.Object []] contains a method named 'Split'.)
  # So I tried to divide the table like this. ForEach ($Task in $Rtask.Name - Split("")) {Write-Host "my tasks are:" $Task}

  
  Get-task-status Running | Export-CSV "E:\scripts\Current_Tasks.csv".
  $InputFile2 = import-CSV "E:\scripts\mmca\mmca_Current_Tasks.csv".
  $InputFile2 | {ForEach-Object
  $RTask = $_. Name
  Write-Host "current task is: ' $RTask
  IF ($RTask - eq "CloneVM_Task") {}
  Write-Host "current task of Clonning is: ' $RTask
  Write-Host "in the meantime the cloning process finish.
  Waiting-task-task $MyTask
  }
  Else {}
  Write-Host "no cloning process is executed.
  }
  }
  
  # This allows the NIC and set the correct Port Group
  Get-VM-name $GName | Get-NetworkAdapter-name $NIC | Together-NetworkAdapter - NetworkName $NIC_Lable-confirm: $false - StartConnected $true
  
  }

  When I run the present, I get the following:

  # #This shows the task start Clonning #.

  erverId: /[email protected]:443 /
  Status: running
  IsCancelable: true
  PercentComplete: 5
  StartTime: 03/05/2013 00:52:13
  FinishTime:
  ObjectId: VirtualMachine-vm-382
  Result:
  Description: Clone virtual machine
  ExtensionData: VMware.Vim.Task
  ID: Work-task-2070
  Name: CloneVM_Task
  UID: /[email protected]:443 / task = work-work-2070 /

  #########################################################

  # #Runs through the tasks running.

  Current task: deploy the model to the FVO
  No cloning process is executed

  # Ignore deploy it task #.

  # #Matches the If statement and continues to process #.
  Current task is: CloneVM_Task
  Task current Clonning is: CloneVM_Task
  Wait for the cloning process to complete

  # #Error #.

  Waiting-Task: cannot bind parameter 'task '. Impossible to convert the value of 'CloneVM_Task' to type 'System.String' type 'VMware.VimAutomation.Sdk.Types.V1.Task '.
  E:\scripts\Working_Create_Master_Templates.ps1:71 tank: 24
  + Wait-task-task < < < < $RTask
  + CategoryInfo: InvalidArgument: (:)) [waiting-Task], ParameterBindingException)
  + FullyQualifiedErrorId: CannotConvertArgumentNoMessage, VMware.VimAutomation.ViCore.Cmdlets.Commands.WaitTask

  $$$ Under notes show a little history of how I got to this point.

  Note1: The first attempt, I have just captured tasks currently running and pending their past to the task. "Well, since the deploy OVF and ClonVM_Task where it runs would wait up to two when completed by the end."

  NOTE2: So I added the If Else loop below which failed because $RTask never equaled only CloneVM_Task, but was a picture of two tasks.

  Note3: I tried to use the following to divide the two tasks:

  $RTask = get-task-status running (who captured the two tasks running)

  foreach ($Task in $Rtask - Split(""))
  {
  {Write-Host "my tasks are:" $Task}
  IF ($Task - eq "CloneVM_Task") {}
  Write-Host "current task of Clonning is: ' $Task
  Write-Host "in the meantime the cloning process finish.
  Waiting-task-task $Task
  }
  Else {}
  Write-Host "no cloning process is executed.
  }

  
  }

  # #Output the little script above #.

  Current task: deploy OVF model CloneVM_Task
  My tasks are: deploy
  My tasks are: OVF
  My tasks are: model
  My tasks are: CloneVM_Task
  Task current Clonning is: CloneVM_Task
  Wait for the cloning process to complete
  Waiting-Task: cannot bind parameter 'task '. Impossible to convert the value of 'CloneVM_Task' to type 'System.String' type 'VMware.VimAutomation.Sdk.Types.V1.Task '.
  Online: 11 char: 24
  + Wait-task-task < < < < $Task
  + CategoryInfo: InvalidArgument: (:)) [waiting-Task], ParameterBindingException)
  + FullyQualifiedErrorId: CannotConvertArgumentNoMessage, VMware.VimAutomation.ViCore.Cmdlets.Commands.WaitTask

  I'm new to Powercli and I've scoured Google for a possible answer. I thought I might have a solution that has been published on the VMware PowerCLI Forum, but I couldn't get this to work. Any help would be greatly appreciated.

  #########################################

  I wasn't worried about how to tasks where splits, unless I was trying to follow the import fo the OVF, so that the script went into the loop If and as one of the names for CloneVM_Task then he Treaty. But I got the same error I did in the last version of the above script. That's why I have the version curent thinking that if I exported and then imported the tasks it might make a difference.

  I'm new to Powercli and would like a little help. I am either very close or by a mile off. :-)

  Thank you

  Mitch

  Why don't you store the the task object that is returned when you use the RunAsync switch?

  You can create a loop around the State and wait until the clone job is done.

  $task = New-VM -Name MyVM ... -RunAsync 
  
  while($task.ExtensionData.Info.State -eq "running"){
    sleep 1  $task.ExtensionData.UpdateViewData('Info.State')
  }
  

  The big difference with the Wait-job cmdlet, it is that this will allow you to perform additional work in the While loop.

  Waiting-task the cmdlet waits just until the task is finisned and you can not do anything else.

• The wait for the customization of the vm finish

  Hi, I am trying to find a way to wait for customization of vm finish before moving on to the next script. That's only 1 vm. I've seen a screenplay written by Lan Renouf, according to me, but I don't know how to change the script to look at the State of only 1 vm instead of several. Any help would be appreciated! Here is the link to Alan if anyone is interested:

  http://blogs.VMware.com/vipowershell/2012/08/waiting-for-OS-customization-to-complete.html '

  Thanks in advance

  Remove the RunAsync parameter

• SRM does not wait for the guests of the DPM enabled

  Hello

  We are testing our environment vsphere 5/SRM and essentially 5, everything goes very well except for wake up initiated by the SRM to the DPM active guests.

  --------------------------------

  The SRM 5.0 doco States:

  SRM temporarily disables DPM for the cluster, and ensures that all guests there are lit before recovery begins. After the recovery or the test is completed, SRM reactive DPM for the cluster, but it hosts are found in the current state of execution while DPM is able to feed them downwards as needed.

  --------------------------------

  The question that we see is that SRM send indeed wake up for guests in mode standby and milestone of recovery as a success. The problem is that SRM does not wait until the guests are completely turned on before before feeding on the VMs. The day before hosts to wake the system correctly storage access newly presented no problem. The problem is that the bubbles to test network is not created on the hosts of the day before and no VMs are assigned to these hosts during the entire test.

  That said, I checked the advanced settings and I cannot find a setting that will force SRM to wait for the standby hosts to be fully integrated in the cluster before you perform additional steps.

  Everyone knows this behavior? Am I missing a setting somwhere? My fear is that this behavior will happen during a real failover and potentially cause problems.

  Thank you for your time,

  Smokey

  Hello

  This should not happen.

  Can you please open a SR, download bundle Journal, engineers will be able to understand what is happening?

  Once you open a case, display the number of SR.

  Michael.

• Don't want to wait for the results of the query

  Hello world.
  
  I'm on CF 7 and SQL Server 2005.
  
  I call a procedure stored through my CF code. The process can potentially take an hour or two to run. I would like the proc run on SQL Server, but don't want my page of FC wait for the results before we continue, I want just the code that follows the proc will run while the database server do it is something silently in the background. Is it possible to do this?
  
  Thank you

  You could try to create a job that calls your long-term stored procedure. In the CF, call the sp_start_job system stored procedure to start your work. I think sp_start_job returns at the start of the task, not when the work is complete, but you will need to test this.

  http://msdn.Microsoft.com/en-us/library/ms186757 (SQL.90) .aspx

• Difference between waiting occupied buffer and read by the wait of the other session in 10g

  Hello
  
  Can someone let me know the difference between waiting occupied buffer and read by other session wait in 10g
  
  Thank you

  http://download.Oracle.com/docs/CD/B19306_01/server.102/b14237/waitevents003.htm#sthref2988

  
  buffer busy waits

  Wait that a buffer becomes available. This event occurs because a buffer is either be read in the buffer cache by another session (and waiting for this reading end the session) or the buffer is the buffer cache, but in an incompatible mode (in other words, some other session changes the buffer).
  

  http://download.Oracle.com/docs/CD/B19306_01/server.102/b14237/waitevents003.htm#sthref3159
  
  read by another session

  This event occurs when a session requested a buffer that is currently being read into the buffer cache by another session. Prior to version 10.1, expected for this event have been grouped with the other reasons for waiting for the buffers under the event "wait occupied buffer.