Watch crashed during the update to look at iOS 3

Similar Questions

• Equium A60 crashed during the update of the Bios

  Hello, can someone tell me if this can be repaired. IHAVE an A60 Equium that crashed during the update of the BIOS, now he died nothing lights up.
  Thanks in advance

  I presume that the BIOS chip is damaged. In this case, you can do anything to make it work again. Just approved can help.

  The problem is that the repair can be quite expensive. Check it out. If selling Yes the laptop on eBay and... you know what I mean. :(

• Satellite A210-15Y crashed during the update of the bios

  The worst case has happened and the laptop computer crashed during an update of the bios. I know that there is the possibility to repait the bios with a tool of recovery from crisis. For this purpose you have to press 2 keys (in most cases FN + B or Win + B) during the connection of the supply cable and the next start. I tried many books, but nothing happened. Can someone tell me the keys on which I have to press a 210 - 15Y satellite and maybe where I can get an image of cd of the tool of the crisis, because the laptop does not have a floppydrive?

  Hello

  As far as I know that the BIOS crisis procedure may be crazy by a technician of the ASP.
  You can not download a version of traditional BIOS who can update the BIOS from a USB FDD floppy.
  You can download only focused on the victory of the BIOS that can be run so that windows operating system is running.

  In my opinion, you should get in touch with a local ASP!

• Satellite Pro L100 - Crash during the update of the Bios

  Hello

  I am the owner of a Satellite Pro L100 (PSLA4E)

  On the Toshiba site I downloaded the BIOS update. While installing I read that it was necessary to supply cable is plugged. Before I could cancel for the cable, he had started and then frozen. The computer stopped working and so I turned it off! Since then, I've read that it was a very big mistake!

  When put on the fan starts and I can hear etc cd drive spinning. After 15 seconds, the screen is blank, the computer starts beeping!
  Is there a way to solve this?

  Thank you very much
  Rich

  Hi Richard

  Seems not good buddy from your description, that something went wrong during the update procedure and now the ROM module has been flashed properly.

  Maybe you area lucky man and the motherboard isn't too bad, but only the Rom module must be flashed again.

  Unfortunately, this must be done by the technician of the ASP. You will need to contact the ASP in your country for assistance.

  Good luck and have a nice day

• 1130us Envy4 crashed during the update of the BIOS

  Hello!

  I just killed my laptop Envy4-1130us favorite.

  I decided to update the BIOS of v.13 to v.25

  During the update process, mogen of BONE (Win8.1) upwards. No error has been shown. After restarting laptop for a few hours, and now it is not working. Supply duct is turned on, the system fan works at full load, but the screen is black, and system does not (OS not start and does not not the power button).

  Community can help me? An it's the BIOS of the laptop recovery console?

  PS: Excuse my English.

  Update:

  When the laptop was completely unloaded, I plugged in the AC adapter.

  It powers on and then the bios recovery procedure has been started.

  So now I have a BIOS v.10

  Thank you HP Bot now my desire to NEVER been updated bios

• crashed during the update does not start now

  my computer laptop gateway arrested during an update (not sure which). It does not start, I get a file missing or corrupt ntoskrnl.exe error. My repair disc does not work either, I read in the forum vista repair disks are not recognized if you instaledl a service pack. So if this is the case where should I go from here. I would be most grateful for any help. jpshan

  It seems that the update has affected your daughters to start.

  ·        Do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not resolve the problem, try the following:

  To run the Bootrec.exe tool, you must start Windows RE. To do this, follow these steps (you may need an Installation of Vista disc to do that)

  1. put the Windows Vista installation disc in the disc drive, and then start the computer.

  2. press a key when you are prompted.

  3. Select a language, a time, a currency, a keyboard or an input method, and then click Next.

  4. click on repair your computer.

  5. click on the operating system that you want to repair, and then click Next.

  6. in the System Recovery Options dialog box, click command prompt.

  7. type Bootrec.exe, and then press ENTER.

  Note If rebuilding the BCD does not resolve the startup problem, you can export and delete the BCD, and then run this option again. In doing so, you ensure that the BCD is completely rebuilt. To do this, type the following commands at the command prompt Windows RE:

  ·        bcdedit/export C:\BCD_Backup

  ·        c:

  ·        Boot CD

  ·        BCD attrib s h - r

  ·        Ren c:\boot\bcd BCD.old

  ·        Bootrec /RebuildBcd

  If this does not work, then withdraws EasyBCD http://neosmart.net/dl.php?id=1 and run this process and see that helps.

  If not, then please repost your question in Forum Windows Update: http://social.answers.microsoft.com/Forums/en-US/vistawu/threads where update problems specialists will be happy to assist with the problems you have encountered. Be sure to include the names and numbers KB ALL updates that have been installed before this problem started.

  Good luck and I hope this helps!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Satellite Pro A60 crashed during the update of the BIOS

  Updating to BIOS ver 1.70 to 1.90 (from Windows XP) my Satellite Pro A60 off without any warnings. After about 5 minutes of waiting I went it. And... computer just several beeps and stops again.
  Anyone has idea what it means? Is it possible to turn it on again?

  Hi Vladimir,.

  I suspect that your BIOS is damaged when your A60 turns off. Unfortunately, this means you A60 are a failure now his POSITION leading to generate failure codes series.

  As Felix said codes tells the Toshiba Service Agent exactly what the problem is so you will need to contact them for assistance.

  HTH

• Windows 8 crashed during the last update, now wants to save and may not do.

  Windows 8 crashed during the last update. Stuck at 30% for more than 4 hours before I finally pressed the power button to restart the system. Windows 8 Pro with Media Center now says system build 9200 at the bottom right of the screen.

  Whenever I try to activate Windows 8, it cannot connect. When you use the command prompt Windows + R and slui 3 with my purchased serial number I get Code 0 x 80070424. Description: The specified service does not exist as an installed service.

  Hello

  This error can appear if your firewall settings prevent Windows to complete the online activation process. To resolve this problem, you can activate Windows by phone instead.

  1. Enter in the right edge of the screen and then click on Search.
     (If you use a mouse, point to the upper right of the screen, move the pointer of the mouse down and then click find.)
  2. Type SLUI 04 in the search box, type or click on applicationsand then tap or click SLUI 04.
  3. Follow the instructions on the screen.

  Hope this helps

• Satellite Pro A110 crashes during the transfer of the large data in LAN

  Hello

  My Satellite Pro A110 crashes during the transfer of the large data in LAN. The network driver is a Realtek RTL8139/810 x Family Fast Ethernet NIC I've been looking through this forum and found some wire whit exactly the same problem, saying that the solution is to update Realtek lan set up in BIOS, not the computer BIOS, but I can't find any link to download the necessary upgrade file. Can anyone tell me please where to find this upgrade file or send it to me directly?

  Thanks in advance

  Is - this transfer of data in the company where you work? Do you want to download data from the server, or how to understand this? How to understand what you mean under big data?

  Have you tried downloading data on the Internet? For example, if you try to download some trailer HD (more than 200 MB)?

• iPad froze during the update and may not exceed

  Has obtained the new ipad and put in place.  Went do the last software update and it froze during the update process.  Blocked at the white screen with the apple logo.  Can not pass it and past 2 hours.  Tried to restore through itunes, but get the error that I need to enter my password which I can't because I'm stuck on the white screen.

  Hey there smbirchler,

  Congratulations on your new iPad! Looks like you were updating the iOS version, the device froze, and now you can't pass the white Apple logo screen, even after you try to restore in iTunes. I know how happy I am when I get a new camera, so we'll work together on that, so you are able to enjoy your iPad mini.

  We will have you try to use the device in Recovery Mode. Take a look at this article for how to do this:

  If you are unable to update or restore your iPhone, iPad or iPod touch

  Thanks for being a part of the communities of Apple Support!

• Equium A60 Notebook failure during the update of the BIOS

  Hello
  My computer crashed during the BIOS update recommended to treat the blue screen error message. I have turned it off completely and now it won't start at all. No lights turn on or it's like there is no power getting to the machine. My outlet does work as I have tested. This could mean my battery is dead? I tried to remove and clean the contacts or the update of the BIOS had something to do with it?

  Thank you
  Phil

  Hi, Phil the A60 sometimes fails started well only very rarely that incidentally that happened to me once. To solve this problem requires the removal and re-sitting of the battery pack. However, in your case, it sounds very likely the BIOS update has failed unfortunately is a return trip to Toshiba.

  Richard S.

• Windows 7 BSOD after accidental shutdown during the update

  Stop computer accidentally during the update of windows. Now computer stuck in a loop of startup blue screen. Safe mode and windows recovery all lead to the blue screen. I don't have a recovery disk. What should I do?

  Hello

  According to the description of the problem, your computer is stuck in blue screen loop. So, I suggest you to create installation media by following the steps described in the article mentioned below and after that try to run automatic reapir.

  Download Windows 7 Disk Images (ISO files)

  After you create the Bootable USB key, change the boot priority and set it to USB. If you are unsure it is advisable to contact manufacturer FRO even. After changing the boot priority is trying to start your computer by using the bootable USB key.

  To run the repair to start the Windows recovery environment (WinRE), follow these steps:

  • Insert the Windows installation disc in the disc drive, and then start the computer.
  • When the message press any key to start from the CD or DVD is displayed, press a key.
  • If your PC does not automatically detect the media
  • When the computer reboots, read on screen for instructions that explain how to interrupt normal startup and access the basic input/output system (BIOS) configuration utility. Most PCs use the F2, F10, ESC or del key to start the configuration of the BIOS.
  • Looking for a tab in the BIOS configuration utility that is labeled boot order, The Options of Bootor Boot. By following the instructions on the screen, use the arrow keys to go to the boot order, and then press ENTER.
  • Locate the flash USB, DVD or CD player (this could be called removable device) in the startup list. By following the instructions on the screen, use the arrow keys to move the drive to the top so that it appears first in the startup list. Press ENTER. The startup command sequence is now changed to boot from the flash drive, CD, DVD, or USB.
  • Press F10 to save your changes and exit the BIOS Setup utility. Select Yes in the confirmation window. The PC will restart.
  • Select a language, a time and a currency, a keyboard or input method, and then click Next.
  • Click on repair your computer.
  • In the System Recovery Options dialog box, select the drive of your Windows installation, and then click Next.
  • In the System Recovery Options dialog box, click on repair your computer.
  • Click the operating system you want to repair, and then click Next.
  • In the System Recovery Options dialog box, click Startup Repair.

  For more information about System Recovery Options, see What are the system recovery options in Windows?

  For more information about the Startup Repair, see Startup Repair: frequently asked questions.

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

  Kind regards

• Smartphones from blackBerry Torch 9800 completely erased during the update

  When I plugged my phone into the computer to charge, an update came on the bb Desktop Manager - to update to 6.0 Bundle 2467 - and I started the update.  After a few minutes, I realized that I have to back up my phone before the update but Office bb wouldn't let me - he said that HE had to be updated.  If the device software update paused until the Office update was complete.  When it was over, the update of the device continued... and I have no back upward.

  Somewhere in the middle of the update (after about half an hour) the phone blinked, there was funny "beep" and a message came that the update could not continue.  The phone has rebooted, but was stuck at about 65%.   I let it sit for a few minutes, still doesn't move do not.  Pulled the battery, let stand a few minutes like that and then reintegrated.  Began to restart, then won again at the same place.  Taken from the battery after a few more minutes and wait for about 15 minutes.

  When I put the battery back, the phone quickly started completely... but because the updater won Mid-implementation to date ALL is lost! Contacts, calendar, memos.

  Is it possible to recover whatever it is? Or all my data lost somewhere in cyberspace is?

  * There is a small file, about 5 MB called Contacts Blackberry so I thought I could synchronize the files from there, but I don't know how!

  Can anyone help?  Really aggravated in this topic...

  Hello and welcome to the community!

  First of all, we will be sure your BB works correctly and with the proper operating system. Is it? What you have said, I can't say for sure. If it does not work, then you can reload your new OS itself, just to be sure. Don't worry about all the data on your BB... he already went there now (based on what you said).

  For your data, Desktop software must have made a backup during the update process... sometimes, we offer the chance to overcome that... I hope that you do not have. In any case search your computer for files with the extension of the IPD or BBB (depending on the version of the Desktop software you use)... These are the files that would have been created on your computer when the update process performed the backup. Look at the time, the files were created... created around the time you were doing the update are candidates to perform a restore of your BB.

  Otherwise, if you had made use of yourself of the free app of the BB Protect your data are indeed "in the clouds" available for to restore you.

  In addition, if you use a Desktop Organizer (for example, Outlook), which must contain your data.

  In addition, if you have none of these, then you have indeed now met data loss, which is sad indeed.

  Good luck!

• My mac crashes during the installation of the cs6. I have to turn off the mac. Now, I can't reinstall or uninstall cs6. He said the Installer failed to initialize.

  My mac crashes during the installation of the cs6. I have to turn off the mac. Now, I can't reinstall or uninstall cs6. He said the Installer failed to initialize.

  If you have not yet installed any Adobe application, try step below and check.

  Step 1

  (1) right-click on the icon in the Finder, then select 'Go - To' folder.
  (2) you will get a text box, type in the following command and then press the 'return '. ( "Don't miss ~ symbol" )

  ~/Library

  It will open the folder of the user's library.

  (3) then navigate to Application Support > Adobe.

  Open the Adobe folder and rename the OOBE, OOBE old and AAMUpdater to old AAMUpdater.

  Step 2

  (1) right-click on the icon in the Finder, then select 'Go - To' folder.
  (2) you will get a text box, type in the following command and then press the 'return '.

  / Library

  It will open the folder System Library.

  (3) then navigate to Application Support > Adobe.

  Open the Adobe folder and rename the folder Caps Caps-old and young OOBE to centenarians, OOBE Adobe Application Manager of Adobe Application Manager.
  

  
  

  Step 3)

  Basket of Adobe Application Manager of Applications > utilities.

  Step 4) [same step again]
  

  Click on the link below and download Adobe Application Manager and install the same:

  http://download.Adobe.com/pub/Adobe/creativesuite/CC/Mac/ApplicationManager9.0_all.dmg

  Once installation is complete, niche is going disappear, and then open the Application folder and locate the icon to launch Adobe Application manager, double-click it and update.

  Once the update is complete.

  Restart the computer once and try to install CS 6.

• Problem with CS5 to crash during the insertion or deletion of page

  I have a legacy file (teaching manual) which was created in CS2 and has been edited and updated over the past two years with no problems. The file is about 360 pages, with about 30 illustrations, table of contents and index larger size. During the updating of the material today, I went back to insert a page because the text to overflow and InDesign crashed. This happens whenever I try to insert or delete a single page. I can insert a single page on the pages i to viii, but when I try to insert a page in InDesign Sec2:1 early crashes. I can open and close the file, and edit anywhere without any problem.

  If I insert 2 pages at a time, it works fine and I can run the text on the page. But when I delete the extra page that I don't need, it crashes. It doesn't seem to be specific to any specific master page in the file. I tried several times to export to an IDML file, reopen and save it in an InDesign file, but the same problem occurs.

  The same thing with the file on the same verson InDesign which is on my laptop. This problem does not occur with other InDesign files that I've created in the past. I need help. Thank you!

  I just thought some about this, so I'm glad you popped up again.

  Seems to me you have two choices, go back to the previous version which works and re-do much editing or try to fix later. If you want to go back, open the file and check the bey in the history of file holding the CTRL key while you choose about InDesign from the menu help. You will see the full backup history in the lower left corner of the dialog box. I check for the latest version, that it has been saved, then open the file in this version and export into .inx (in CS4 or earlier) or .idml .idml for CS5 or later, and then open the .idml in CS5 and save as a new .indd and proceed.

  The existing file, you can divide and conquer stuff, but like I said, I thought instead, and in your shoes I would probably ignore the first step and try to export to text marked for each story, and then build a new doc by placing the tagged text. If it seems to be OK, place the images again and go ahead.

  Whatever it is, I think you have some heavy lifting.