What is the correct alignment? (sandisk extreme 240 GB)

each review seems to show an alignment of 1024 k as ssd, as here http://img.hexus.net/v2/SSD/SanDisk/Extreme240/AS-SSDb.png

However my drive is set to 234496 in windows 7.  This is a new installation, the ahci enabled and the intel rst installed 10.8.  Also using the R201 firmware.  All other drives have been disconnected when I installed. c3/c6 processor disabled in the bios.

Data sheet:

P8z68-v pro gen 3

I7 2600 k

8 GB of ddr3 memory

Corsair ax850psu

Say you clone the drive, then use a partitioning tool to set the alingment?

as long as AS SSD presents this green number you alignment is good to go. Basically any number can be displayed here so it is evenly divisible by 4, you're good to go.

Tags: SanDisk SSD

Similar Questions

  • What is the correct recovery process once upgraded to Windows 10? (No OneKey Recovery)

    I have a cell phone Z50-70 which is preinstalled with Windows 8.1. It is an OEM version, with the product key that is stored in the Bios. This is an installation of UEFI.

    The vehicle currently has OneKey recovery installed, which, if I understand well (I've not used actually still), allows you to recover from a hard disk recovery partition. This is not a "fresh" Windows 8.1, but an image provided by Lenovo that take back you to the State the laptop was bought originally (will have all software Lenovo and preinstalled drivers).

    According to the official upgrade guide Lenovo, before performing the upgrade of Windows 10, we should uninstall basically all software from Lenovo, including OneKey recovery and it won't work in Windows 10.

    Issues related to the:

    1. What is the correct process to recover the system from Windows 10 if something goes wrong? I think that Windows 10 integrates a feature "Reboot your computer" in the settings which I suppose is what we are supposed to use. It would take me to:

    a. a completely new install Windows 10?

    b. a created image during the upgrade from 8.1 to 10, containing all my files etc. when performing the upgrade?

    c. or he would use the recovery partition from Lenovo (which would have used OneKey Recovery if it was compatible) and take me back to 8.1 for Windows?

    (d) another thing?

    2. once I did the upgrade and Windows 10 has successfully activated, I think I could create a bootable with ISO of Windows 10, inside boot media and install a completely new install of Windows 10 and activate it. Theoretically, I could make as many fresh installs from the boot media I want, as long as initially, I did the upgrade (not a clean install), and the hardware of the laptop does not change. Is this correct?

    2A. If, therefore, during the first boot media clean installation process, I'd be sure compeletly remove the Lenovo recovery partition entirely and go from there, rely on 'Reset your PC' feature of Windows 10? Could I could use even just reinstall Windows boot again media 10 as a way to recover? If I understand correctly, it is not absurd to keep recovery partition it if it can not be used within Windows 10.

    I think I had a desktop PC ordinary with a retail version of Windows, then everything above would be fine. The complications added here are that 1. I have no product key Windows 8.1 (alll is managed by the BIOS) and 2. I have no recovery disk. I want to make sure that I understand everything completely before moving, and potentially do a clean installation using bootable media, so that I don't end up ruin something and end up with either a laptop I can not recover, a Windows installation that is not enabled.

    Thank you.

    Update for anyone of another reading:

    I just uninstall OneKey recovery on my installation of Windows 8.1 for the upgrade. While Windows is concerned, OneKey Recovery has been completely removed.

    The good news is that I then shut down the laptop, you press the novo button, selected "System Recovery" and I was always greeted with OneKey recovery program where I could choose to restore from original image, or a custom image. So I guess that once I have upgraded to Windows 10, I'll always have the option to restore to the factory Windows 8.1 if I ever need/want to.

    The confusion seems to be that OneKey recovery software is actually two separate software:

    1 OneKey Recovery #1 is installed in the hidden recovery partition which is responsible to perform a system restore from the image of your choice - either the image of plant or a custom image created by #2 OneKey recovery software. OneKey Recovery Software #1 is still accessible via the Novo button.

    2 OneKey Recovery #2 is installed on the Windows 8.1 installation, which is responsible for the creation of custom system images. You can also choose to restore the system from here, but AFAIK, it just restarts the computer and OneKey #1 software, which allows you to recover expenses. OneKey Recovery #2 is the software Lenovo told us to uninstall it before Windows 10. However, uninstalling OneKey Recovery #2 let software OneKey Recovery tact #1.

    As far as I know, this means that the uninstall OneKey Recovery #2 mean that we lose the ability to create custom system images, but we reserve the option to restore from a system image.

    Can anyone confirm that I understood, and that what I said above is indeed the case?

    I'm still a little uncertain about what Windows built tens in the willingness to ' PC ' do well - that it will use the Lenovo recovery partition or run a 10 Windows Installer Clean up.

  • What are the correct settings in outlook express to pop and smtp in att.yahoo?

    What are the correct settings in outlook express to pop and smtp in att.yahoo?

    If it's a US or CA, Yahoo account, and that you are not subscribed to Yahoo Mail Plus, then you cannot access the account in Outlook Express.

    POP Yahoo! Mail more for Outlook Express configuration
    http://Overview.mail.Yahoo.com/enhancements/mailplus

  • margins for the printer so the words are not cut on the right side. What are the correct numbers for size printing letter?

    What are the correct for the printer margin settings so that everything is on paper, without truncating them.?

    What are the correct for the printer margin settings so that everything is on paper, without truncating them.?

    go to the icon for your printer, go to the page set up, size, A4 sheet? 19.05 mm pitch all sides, mine is set up for this and it seems ok. or what you like

  • Vista will not start! Black screen, no mouse, no cursor pointer. Startup Repair cannot repair. Details say 'wrong pass '. What is the correct syntax for pkgmgr to uninstall?

    Vista will not start!  Black screen, no mouse, no cursor pointer.  Startup Repair cannot repair.  Details say 'wrong pass '.  It looks like all the files are well intact on the disk.

    What is the correct for pkgmgr syntax when you try to uninstall an update by using a command prompt when starting Vista OS disk?  I entered the following in the "x:\Sources >" prompt:

    start /w pkgmgr/o: "C:\; /Up:Package_1_for_KB2840149~31bf3856ad364e35~x86~~6.0.1.0 C:\Windows.

    When I run this command it ends quickly and when I run 'echo %errorlevel%' I get '5', which seems to mean 'access denied'.  How am I supposed to have access to remove the patch?  Am I missing something?  Perhaps a switch in the syntax to access?  Help, please.  Thank you.

    I tried both options that you recommended.  As initially stated, no boot option would produce something other than the black screen.  I tried to boot from a drive and restoring the system running, but she didn't, and when I tried to do it again the recovery console could not find restore points. ?.

    An update, the computer is now fixed.  Oddly enough, I ran recovery of starting a drive at least 8 times and each time I checked the details and he said: he ran chkdsk without error and return to the same cause "a patch is preventing windows to start.  I even ran chkdsk c: /f from a prompt command from the recovery disk and it found no errors.  That's when I posted the question above after trying to remove the patch in the manner described above.  After some time and frustration, I decided to run chkdsk /r c:.  It took awhile, but it found 1 bad sector, moved the data, the bad sector tag and finished.  Once I restarted from that, everything came and went very well.

    So, the original question remains, what was missing in the command to run pkgmgr/high: successfully.  And the new question exists as to why start Recovery claims run chkdsk if it does not, or he turns the version/f not the version/r the same as I did manually?  It would be good to know for the future.  Thank you!

  • What is the correct URL for the commercial intent tool?

    I'm in the middle to make a transfer online. I need to know the tool the URL of Microsoft online commercial intention.

    I like: adlab.microsoft.com/Online-Commercial-Intention/default.aspx

    I tried Microsoft and a google search...

    This tool still exist? And if so, where? What is the correct URL?

    Thanks for your help!

    This is the site for

    http://ADLAB.Microsoft.com/audience-intelligence.aspx

    But when I click on the online commercial intent tool, the page is not found.
    http://ADLAB.Microsoft.com/online-commercial-intention/

    I would like to use the contact information on this page to see if the tool will be available:
    http://ADLAB.Microsoft.com/contact-us.aspx

    Contact information
    • Microsoft Bing Ads Labs
    • 1 Microsoft way, Redmond, WA, 98052-6399
    • Phone: 425.882.8080
    • Fax: 425.936.7329
    • E-mail: * e-mail address is removed from the privacy *.
    • Website: http://adlab.microsoft.com

      Sincerely,

      Marilyn

  • What is the correct order of network provider

    original title: network provider order

    What is the correct order for network providers.

    my choices are:

    a. provide Dell Wireless WLAN Card Logon
    Server Desktop Session host remote M/Soft b.
     c. Web Client Network and
    d. M/Soft Windows network...

    Hello

    The order of network providers can be changed according to the requirement. I suggest you to see the following link on the change of the network adapters.

    Modify the protocol bindings and the network provider order
    http://TechNet.Microsoft.com/en-us/library/cc732472 (v = ws.10) .aspx

  • What is the correct syntax to reference a page point (P23_ID, for example) in a process of PL/SQL page after submit?

    What is the correct syntax to reference a page point (P23_ID, for example) in a process of PL/SQL page after submit?

    TexasApexDeveloper wrote:

    Variable binding is preferred: P23_ID you can also use & P23_ID. (variable substitution notation).

    Bind variable and static text substitution references are not interchangeable. For example, static text substitution references cannot be used in allocation targets:

    :P23_ID  := 'foo';  -- valid
    &P23_ID. := 'bar'; -- syntax error (or something weird or sinister due to SQL injection)
    

    Substituting static text references should be avoided in SQL and PL/SQL code because of the risk of behavior topic SQL injection and / odd error because of values containing quotes, etc.

  • What is the correct procedure to take a host of a hav?

    Sometimes need to take a host far a hav, what is the correct procedure for it?

    Thank you!

    George

    Disconnect the host in your cluster, and then remove host.  Or evacuate all customers outside the host, put in maintenance mode, and then remove the cluster

  • What is the correct version of Flash Player for Kindle Fire HD?

    What is the correct version of Flash Player for Kindle Fire HD? Where do they find it? How can I install? Thank you.

    Hi nani2eande,

    The last Kindle Fire HD is not officially supported by Flash Player.  Please see this page for a list of all certified devices:

    That said, some users were able to get Flash Player working on Kindle using Dolphin fire, a third of browser.

  • What is the correct procedure to abandon diskgroup asm is rac?

    Hello

    I would like to table a diskgroup in asm to the CCR? What is the correct procedure?
    1 should I disassemble the diskgroup firstly in 2 node?
    2 alter diskgroup xxx drop command to run in the 2 nodes or just 1 node?
    3. after droping command, is there any other procedures to be done?

    No matter what doc to follow?

    Thank you

    Andrew

    Hi André,.

    860523 wrote:
    Thank you very much. Oracle 10.2, if I unmount the diskgroup, I want something offline, or what is the procedure before changing disgroup xxx disassemble?

    You MUST remove (using DBCA) or move (using RMAN) all databases stored on the diskgroup (if exists) before giving up DISKGROUP.
    (1) check if there are any database using the DISKGROUP.
    The query above must return no rows.

    SQL>  SELECT D.NAME,C.INSTANCE_NAME,C.DB_NAME,C.STATUS
         FROM GV$ASM_DISKGROUP D , GV$ASM_CLIENT C
         WHERE D.GROUP_NUMBER=C.GROUP_NUMBER
         AND D.NAME = '';  
    
    no rows selected
    

    If the above query returns rows you remove and stop must all first trial or move the database to an another DISKGROUP.

    (2) remove the Diskgroup all instances of ASM, except one.

    ALTER DISKGROUP  DISMOUNT;
    

    (3) decline diskgroup of the ASM instance, that the diskgroup is still mounted

    DROP DISKGROUP ; -- If no files on DISKGROUP
    DROP DISKGROUP  INCLUDING CONTENTS; - If exits files on DISKGROUP
    

    Just it.

    Kind regards
    Levi Pereira

  • What is the correct notation for complex variables

    I need to handle files after download. They are all uploaded in 1 directory by a flash component and then I need to rename them, and move to the directory that corresponds to the choice of categories and subcategories. Now I'm having trouble finding how to get my variables correctly

    It's the thisFiletoMove1 variable, it must match the destination file in the cffile tag

    (< FileExists('#request.site.imgupload#\max_#MultiPowUploadFileName_0#') cfif >
    < cffile action = "Rename".
    source="#request.site.imgupload#\max_#MultiPowUploadFileName_0#".
    destination="#request.site.imgupload#\#request.currentimgid#_max.jpg" >
    < cfset thisFiletoMove1 = #request.currentimgid #_max.jpg / >
    < / cfif >

    < cfset thisFiletoMove1 = #request.currentimgid #_max.jpg / > is what gives an error construct CFML invalid encountered, ColdFusion was looking at the following:

    _max.jpg

    Then I try

    < cfset thisFiletoMove1 = #request.currentimgid & "_max.jpg" / > and I get

    The C:\websites\beta.antiek.net\demo\galleries\test\thisFiletoMove1 source specified in the cffile tag is not valid

    So now I wonder, what is the correct way to do this?

    Bianca

    bianca_homedev wrote:

    I need to handle files after download. They are all uploaded in 1 directory by a flash component and then I need to rename them, and move to the directory that corresponds to the choice of categories and subcategories. Now I'm having trouble finding how to get my variables correctly

    It's the thisFiletoMove1 variable, it must match the destination file in the cffile tag


     
    source="#request.site.imgupload#\max_#MultiPowUploadFileName_0#".
    destination="#request.site.imgupload#\#request.currentimgid#_max.jpg" >
       

    is what gives a construction of CFML not valid error found, ColdFusion was looking at the following:

    _max.jpg

    Then I try

    and I get

    The C:\websites\beta.antiek.net\demo\galleries\test\thisFiletoMove1 source specified in the cffile tag is not valid

    So now I wonder, what is the correct way to do this?

    All are both wrong:


    You were near. What you meant was probably

    However, are even better

  • What is the correct syntax for the use of a variable in an ad-hoc query?

    Hi all

    I'm a casual user of the DB and right now need to update the records about 1000 + so that a certain column gets a unique value.

    So I thought I'd use a variable for this.

    Then, I built this type of SQL statement for only a small subset of records:
    ----------
    variable number recNumber;
    exec: recNumber: = 1;
    UPDATE TABLE_TO_BE_UPD
    SET COL_TO_BE_UPD = COL_TO_BE_UPD + recNumber
    WHERE COL_TO_BE_UPD IN ('VAL_A', 'VAL_B');
    ----------

    I get invalid SQL statement error when you try to run above (except for the guest who asks for a value I want to omit).

    In any case, I also tried this one:
    ----------
    CREATE SEQUENCE seqCounter;
    UPDATE TABLE_TO_BE_UPD
    SET COL_TO_BE_UPD = COL_TO_BE_UPD + seqCounter.NEXTVAL
    WHERE COL_TO_BE_UPD IN ('VAL_A', 'VAL_B');
    ----------

    Of it, I got the error ORA-01722: invalid number... I guess it's because seqCounter is of type number and the COL_TO_BE_UPD is of type character... (?)

    Then I want to ask is what is the correct way to define and use a counter variable type to add a number at the end of a string?

    Also another question I would ask is that are variables that are used in queries ad hoc, also called "bind variables"?

    Thank you muchly

    If you want to add a unique number to a column, then it would be:

    UPDATE TABLE_TO_BE_UPD
    SET COL_TO_BE_UPD = COL_TO_BE_UPD ||to_char(rownum)
    WHERE COL_TO_BE_UPD IN ('VAL_A','VAL_B');
    
  • What is the correct query?

    I have two tables: tmp and tmp1. the output should be, for each NOC in tmp, its SOPs should be ALL in the tmp1. The correct output should be "1111".

    I wrote a query based on 1111, it works. But how can I extend to 2222, 3333... ? What is the correct query?

    Thank you.

    select * from tmp;
    
    CNO                    PNO                    
    ---------------------- ---------------------- 
    1111                   10506                  
    1111                   10507                  
    1111                   10508                  
    1111                   10509                  
    2222                   10601                  
    2222                   10701                  
    3333                   10800                  
    3333                   10900                  
    
    8 rows selected
    
    select * from tmp1;
    
    PNO                    
    ---------------------- 
    10506                  
    10507                  
    10508                  
    10509                  
    10701                  
    10800                  
    
    6 rows selected
    
    select * from tmp where 
    cno = 1111 
    and
    not EXISTS(select pno from tmp  where cno = 1111 minus select pno from tmp1)
    
    
    CNO                    PNO                    
    ---------------------- ---------------------- 
    1111                   10506                  
    1111                   10507                  
    1111                   10508                  
    1111                   10509                  
    
    4 rows selected
    Published by: user533361 on 27 Sep 2009 13:47

    user533361 wrote:
    If it has 10000 records ONC in tmp, so we cannot write the query as your method below. I think that we should have other ways...

    Well, just run:

    select  cno
      from  tmp t1,
            tmp1 t2
      where t1.pno = t2.pno(+)
      group by cno
      having count(t1.pno) = count(t2.pno)
    / 
    

    RTFM: WITH clause is just a way to quit smoking to create a table on the fly with your sample data. I don't envy littering my database with tables of all subjects to which I answer :).

    SY.

  • I get the 'BAD IMAGE' when many *.exe files is available. The error image refers to "BROWSE ~ .dll." What is the correct file name?

    When I type (OK) the computer continues to the application, I entered, but there may be a range
    in the opinion of the 'BAD IMAGE' with various. EXE files. Somehow gotten past as the correct file name cut short
    what he should ever TRAVEL ~ .dll. I can rename it leaving out the "~" symbol, but I don't know what to rename it.
    Help?

    Hello

    It would be useful to the Windows OS is supported .

Maybe you are looking for