What is the new 'best practice' for suncing VM in Vsphere 4.0

Similar Questions

• Best practices for network configuration of vSphere with two subnets?

  Well, then I'll set up 3 ESXi hosts connected to storage shared with two different subnets. I configured the iSCSI initiator and the iSCSI with his own default gateway - 192.168.1.1 - targets through a Cisco router and did the same with the hosts configured with its own default gateway - 192.168.2.2. I don't know if I should have a router in the middle to route traffic between two subnets since I use iSCSI ports linking and grouping of NETWORK cards. If I shouldn't use a physical router, how do I route the traffic between different subnets and use iSCSI ports binding at the same time. What are the best practices for the implementation of a network with two subnets vSphere (ESX host network: iSCSI network)? Thank you in advance.

  Install the most common iSCSI would be traffic between hosts and

  the storage is not being routed, because a router it could reduce performance.

  If you have VLAN 10(192.168.1.0/24) iSCSI, VLAN 20 (192.168.2.0/24) ESX

  MGMT and VLAN 30 (192.168.3.0/24) comments VMs and VLAN 40 (192.168.4.0/24)

  vMotion a deployment scenario might be something like:

  NIC1 - vSwitch 0 - active VMK (192.168.1.10) MGMT, vMotion VMK (192.168.4.10)

  standby

  NIC2 - vSwitch 1 - current (VLAN30) guest virtual machine port group

  NIC3 - vSwitch 2 - active VMK1 (192.168.1.10) iSCSI

  NIC4 - vSwitch 2 - active VMK2 (192.168.1.11) iSCSI

  NIC5 - vSwitch 1 - current (VLAN30) guest virtual machine port group

  NIC6 - vSwitch 0 - MGMT VMK (192.168.2.10) standby, vMotion

  VMK (192.168.4.10) active

  You would place you on VLAN 10 storage with an IP address of something like target

  192.168.1.8 and iSCSI traffic would remain on this VLAN. The default value

  gateway configured in ESXi would be the router the VLAN 20 with an ip address of

  something like 192.168.2.1. I hope that scenario help set some options.

  Tuesday, June 24, 2014 19:16, vctl [email protected]>

• What are the best practices for a new employee to learn inside the instance of their business of Eloqua as efficiently as possible?

  We have companies everything changed at some point in our lives. And we all go through the process in the first weeks, where you feel new and are just trying to figure out how not to get lost on your way in the mornings.

  On top of that, trying to familiarize yourself with your new company Eloqua instance can be a daunting task, especially if it's a large organization.

  What are the best practices for new employees to learn as efficiently and effectively as possible?

  I am in this situation right now. Moved to a much larger organization. It is a huge task trying to understand all the ins and outs not only society, but also of the eloqua instance, especially when she is complex with many points of integration. I find that most of the learning happens when I really go do the work. I spent a ton of time going through the programs, documentation, integrations, etc., but after awhile, it's all just words on a page and not absorbed.

  The biggest thing that I recommend is to learn how and why things are made the way they are currently, ask lots of questions, don't assume not that things work the same as they did with your previous employer.

  Download some base in place level benchmarks to demonstrate additional improvement.

  Make a list of tasks in the long term. As a new pair of eyes, make a list of things you'd like to improve.

• What is the best practice for a 'regular' Server VMware and VDI environment?

  What is the best practice for a "regular" VMware Server and VDI environment?   A single environment (ESXi and SAN) can accommodate two if it is a whole new configuration?  Or even better to keep separate?

  Enjoying inputs.

  Quick and dirty answer is that "it depends."

  serioulsy, it depends really two things budget and IO.  If you had the money for two without then buy two and don't have to host your server environment and the other for VDI desktop, their IO profiles are completely different.

  If this is not the case, try to keep each type of use for their own dedicated LUN.

• What are the best practices for creating only time data types, and not the Date

  Hi gurus,

  We use 12 c DB and we have a requirement to create the column with datatype of time only, if someone please describe what are the best practices for the creation of this.

  I would strongly appreciate ideas and suggestions.

  Kind regards
  Ranjan

  Hello

  How do you intend to use the time?

  If you are going to combine with DATEs or timestamps from a other source, then an INTERVAL DAY TO SECOND or NUMBER may be better.

  Will you need to perform arithmetic operations on time, for example, increase the time to 20%, or take an average?   If so, the NUMBER would be preferable.

  You are just going to display it?  In this case, DAY INTERVAL in SECONDS, DATE or VARCHAR2 would work.

  As Blushadow said, it depends.

• What is the best way or best practices for access to the session defined in servelt pipeline component?

  Hi Experts,

  What is the best way or best practices for access to the session defined in servelt pipeline component?

  Please, share your ideas.

  Thank you

  ankV

  As performance is concerned, a lot would depend on as to how your design & logic is implemented and you presented search operations to support the specific performance problems. In fact the operation itself can be not expensive than in-house it is somewhat like a search for key/value of the objects in session/application context name. But having said that, Yes, a potential performance problem could be because it's a synchronized operation. So to avoid searches to be performed during each request, caching the results of a search of a component. And in the majority of cases to solve a 'A' component within your component, you must configure a property reference 'A' in the file properties for your component.

• What is the best practice for the enumeration for the ADF?

  Dear all,
  
  What is the best practice for the enumeration for the ADF?
  
  I need to add the enumeration to my request. ex: sex, marital status.
  
  How to deliver? Declarative custom components or is there another way?
  
  Thank you.
  Angelique

  Check out this topic - '5.3 fill view object Rows with static data' in Guide of Dev
  http://download.Oracle.com/docs/CD/E17904_01/Web.1111/b31974/bcquerying.htm#CEGCGFCA

• I would like to know the "best practices" for unplugging my computer permanently to the internet and other updates.

  Thank you for taking the time to read this. I would like to know the "best practices" for unplugging my computer permanently to the internet and other updates. I thought I would do a clean install of Windows XP, install my Microsoft Works again and nothing else. I would like to effectively transforming my computer into a word processor. He continues more and more slow. I get blue screen errors, once again. I received excellent Microsoft Support when it happened before, but since my computer is around 13 years, I think it is not worth the headache to try to remedy. I ran the Windows 7 Upgrade Advisor, and my computer would not be able to upgrade. Please, can someone tell me how to make it only a word processor without updates or internet connection? (I already have a new computer with Microsoft Windows 7 Home Premium, it's the computer that I use. The old computer is just sitting there and once a week or so I updates.) I appreciate your time, thank you!

  original title: old computer unstable

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/install-Windows-XP

  http://www.WindowsXPHome.WindowsReinstall.com/sp2installxpcdoldhdd/indexfullpage.htm

  http://aumha.NET/viewtopic.php?f=62&t=44636

  Clean install XP sites
  You can choose which site to reinstall XP.

  Once it is installed, then you do not have to connect what anyone, however, some updates may be required to perform the work, test this by installing work and see if you get an error msg. Except that you should be fine.

• Best practices for the installation of 10 GbE

  I have a new HP DL380G7 who has 4 cards on 1 G and 2 10 network interface cards.

  This will run VSphere 4.1 esxi

  I'm looking for some advice on what would be a good network for this server configuration.

  The storage will be NFS goes to a NAS Server

  I tried to create 2 vswitch one with one of the NICs embedded for the service console and the other switch was a team of the 10G env.

  Support Vmware told me that in this configuration, I had to make sure that the service console was on a different subnet from the kernel NFS or NFS traffic will try to go on the service console port.

  I tried this config but as soon as I add a Vkernel to the 2nd switch I am not out ping.

  So I thought I'd post here with what would be a best practice configuration for this server.

  In the first configuration, it is difficult to say which interface will be used for NFS traffic.  Therefore, it is not a recommended configuration.

  The second configuration must be correct.

• Measurement on the side time server? Best practices for the turn-based game

  Hello

  What would be the best practice for measuring time in a turn based game?

  I was looking at the timeout of the room, but to use that it would mean that, for each round, I put users in a new room?

  Is there a way where I can measure time serverside and keep users in the same room?

  If so, I could use php, otherwise, we would need java that allows to measure a time race.

  See you soon,.

  G

  Hello

  You can definitely use PHP or Java - we provide integration of server

  libraries for either. I don't know exactly what is the use case, so I can't

  comment on what makes the most sense, but if it is not information which must be

  totally secure, grading on the client can be a viable approach also.

  Nigel

• Best practices for the integration of the Master Data Management (MDM)

  I work on the integration of MDM with Eloqua and are looking for the best approach to sync data lead/Contact changes of Eloqua in our internal MDM Hub (output only). Ideally, we would like that integration practically in real time but my findings to date suggest that there is no option. Any integration will result in a kind of calendar.

  Here are the options that we had:

  1. "Exotic" CRM integration: using internal events to capture and queue in the queue changes internal (QIP) and allows access to the queue from outside Eloqua SOAP/REST API
  2. Data export: set up a Data Export that is "expected" to run on request and exteernally annex survey via the API SOAP/REST/in bulk
  3. API in bulk: changes in voting that has happened since the previous survey through the API in bulk from Eloqua outside (not sure how this is different from the previous option)

  Two other options which may not work at all and who are potentially antimodel:

  • Cloud connector: create a campaign questioning changes to schedule and configure a connector of cloud (if possible at all) to notify MDM endpoint to query contact/lead "record" of Eloqua.
  • "Native" integration CRM (crazy): fake of a native CRM endpoint (for example, Salesforce) and use internal events and external calls to Eloqua push data into our MDM

  Issues related to the:

  1. What is the best practice for this integration?
  2. Give us an option that would give us the close integration in real-time (technically asynchronous but always / event-based reminder)? (something like the outgoing in Salesforce e-mail)
  3. What limits should consider these options? (for example API daily call, size response SOAP/REST)

  If you can, I would try to talk to Informatica...

  To imitate the integrations of native type, you use the QIP and control what activities it validated by internal events as you would with a native integration.

  You will also use the cloud api connector to allow you to set up an integration CRM (or MDM) program.

  You have fields of identification is added objects contact and account in Eloqua for their respective IDs in the MDM system and keep track of the last update of MDM with a date field.

  A task scheduled outside of Eloqua would go to a certain interval and extract the QAP changes send to MDM and pull the contacts waiting to be sent in place of the cloud connector.

  It isn't really much of anything as outgoing unfortunately use Messaging.  You can send form data shall immediately submit data to Server (it would be a bit like from collections of rule of integration running of the steps in processing of forms).

  See you soon,.

  Ben

• Best practices for adding form fillable form designer EULA & forcing acceptance by the user

  What are created the best practices for adding a license agreement end user to a form with LiveCycle Designer. and to force the user to signify the acceptance of the EULA before access inside the form?

  Time, I have the kludged with a series of four message boxes (which is necessary because my LICENSE agreement, like most) is too long to fit in a single messageBox).  3 first message boxes have OK/Cancel buttons.  If the user clicks OK, she gets the following message EULA box; If she clicks cancel the form closes.  The last post (fourth) area a Yes/No buttons with the corresponding behavior.  It seems that the work (I think?), but it's ugly.  Is there an "easy way" to do it with a single drop-down dialog box "I agree" and "I refuse" custom buttons?

  I've seen references to Tools like this but they are marked as obsolete or abandoned due to security or other unspecified concerns.

  Best, Blake

  Another way might be, keep the form pages hidden at the beginning and only display a single page that has text box that contains the EULA with accept and refuse to scroll buttons. IF someone refuses, you can keep the rest of the hidden form or display message boxes to force acceptance of the EULA.

  If anyone agrees, you can simply hide the EULA page, and display form pages.

  I hope that used here too scripting required to reach it either.

• Best practices for storing the Logs of the system for all newly improved ESXi hosts?

  Hi people,

  What are the options and best practices for the Logs of the system for all newly improved 5.1u1 ESXi hosts?

  Do I need to have the Syslog server or it can be safely ignored?

  Thank you

  Evening,

  Syslog is preferred, but VMware has provided a collector of syslog on the vcenter installation disc can be installed on any windows host or your vcenter. I can't count the number of times where I had guests CMTF or newspapers lost... Fortunately for the syslog which collects up to the accident.  It is not necessary, but it's really a good idea without any real cost since you can use your vcenter host.

  Here is an article on how to install it:

  Set up Syslog ESXi collector | VMware vSphere Blog - VMware Blogs

  Thank you

• vSpere 5 Networking of best practices for the use of 4 to 1 GB NIC?

  Hello

  I'm looking for a networking of best practices for the use of 4-1 GB NIC with vSphere 5. I know there are a lot of good practice using 10 GB, but our current config does support only 1 GB. I need to include the management, vMotion, Virtual Machine (VM) and iSCSi. If there are others you would recommend, please let me know.

  I found a diagram that resembles what I need, but it's for 10 GB. I think it works...

  (I had this pattern HERE - rights go to Paul Kelly)

  My next question is how much of a traffic load is each object take through the network, percentage wise?

  For example, 'Management' is very small and the only time where it is in use is during the installation of the agent. Then it uses 70%.

  I need the percentage of bandwidth, if possible.

  If anyone out there can help me, that would be so awesome.

  Thank you!

  -Erich

  Without knowing your environment, it would be impossible to give you an idea of the uses of bandwidth.

  That said if you had about 10-15 virtual machines per host with this configuration, you should be fine.

  Sent from my iPhone

• best practices for loading the swf file

  Greetings,

  Using CS5 AS2

  I am creating a website in flash (all files are in a directory/folder on SharePoint) and want to make sure that what seems to work well is recommended.

  I have an index.swf with many buttons that will take the user to landing pages/content/other SWFs. On these various buttons, I have the script...

  (release) {loadMovieNum ("name.swf", 0) ;}}                I could also just do {loadMovie ("name.swf", 0) ;} ?}

  Transitions film nicely name.swf and on this page, I have a button that returns the user to the index.swf...

  (release) {loadMovieNum ("index.swf", 0) ;}}   Things back to index.swf nicely and the user can chose to go to a different landing page.

  It seems that I am on the right track, BC., nothing's wrong? but want to check out. I'm following best practices for moving from one swf to another within a Web site?

  Thanks for the help or confirmation!

  You are welcome.