When the closure of XP, get a message another user is connected

Similar Questions

• When the computer is started, get error message sistray has stopped working

  Original title: sistray has stopped working

  When I start my Pc, I get a sign that says "SisTray stopped working" and something like windows are looking for solutions, but whenever I turn it on, just the same sign. What should I do?

  Thank you.

  Hello

  1. what operating system do you use?

  2. don't you make changes to the computer?

  Method 1: Check in safe mode and the clean boot

  For the open procedure the computer in safe mode, open the site mentioned below:

  Start your computer in safe mode.

  http://windows.microsoft.com/en-US/windows7/Start-your-computer-in-safe-mode.

  If the problem does not persist in safe mode, try to start your computer in a clean boot.

  For the procedure to place the computer in a clean boot, open the site mentioned below:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7.

  http://support.microsoft.com/kb/929135.

  Note: to set the computer back to start normally, use the step 7 in the same link.

  Method 2: Update the video driver

  Update driver by following the steps in the site mentioned below:

  Update a hardware driver that is not working properly.

  http://windows.microsoft.com/en-US/windows7/Update-a-driver-for-hardware-that-isn ' t-work correctly.

• My MacBook is not connect to my Time Capsule to back up.  IMac my wife backup fine and our wifi works, but when I try to save, I get a message telling me to connect to the T. C. when it is available, which is never.  Help

  My MacBook Pro is not connect to my Time Capsule so it backs up.  IMac my wife backup fine and our wifi works, but when I try to save, I get a message telling me to connect to the T. C. when it is available, which is never.

  The problem started when I upgraded to Yosemite, sometimes back.  I am running 10.10.5.

  The MacBook Pro...

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click Add or remove from your drive

  Under the heading of backup disks, click on the drive it to highlight (probably named 'Data', unless you have changed the name of the drive)

  Click remove disk

  Close the windows

  Restart the MacBook Pro

  Click the 'clock' Time machine at the top of the screen of the Mac

  Click Open Time Machine Preferences

  Click select drive or Add or remove disks

  Choose the Time Capsule drive (probably named 'Data') by highlighting

  Click use the disk

  Close the windows

  Wait a while to see if a backup is performed

  If you want to manually run the backup, click on the Time Machine clock icon, and then click Backup now

  Report on your results. If the backup still does not work, we need the exact message that you see there.

• When I get a notification of a new email and go and click on the "Mail" cone, I get this message the e-mail address or the password is incorrect. Please try again.

  Windows live ID is OK and open.

  My windows ID is open and OK.
  When I get a notification of a new email and go and click on the "Mail" cone I get this message
  The e-mail address or the password is incorrect. Please try again.

  Then I have to re-enter my details.

  I never had this problem before, whenever I clicked on the "Mail" icon I was taken directly in my mailbox.  It just started this week.

  I use iMac - so I installed the latest version of Live and I still have this problem

  When I enter my details I am taken to the "account overview" and not my mailbox.

  Help!

  Hello

  There seems to be a problem with Windows Live mail, it would be better to post the same question in Windows Live solution Center for assistance.

  Windows Live Solution Center: http://windowslivehelp.com/

  For more information, see the following link:

  Portal email: http://windowslivehelp.com/product.aspx?ProductID=15

  Hope the information is useful.

• When I try to run Age Of Empires with the CD in, I get a message "Please insert the right CD-ROM, select OK and restart the application.

  Former title: Trouble running games CD, post installation under Vista. That is to say 2 AoE, Warrior kings.

  I have vista on my laptop, I installed games like shogun and medieval total war and they both work perfectly, I tried to put it on the age empires and warrior kings: battles who are also on a cd format, I installed the last but they usually run after that. Although the instialltion is over, I get asked if I wanted to leave the program to run as administrator. : s

  DVD/CD drive recognize there is a disc, but does not work automatically. I can't install the program normally when I run the setup.exe for the game. When I try to run the program with the CD in, I get a message "Please insert the right CD-ROM, select OK and restart the application.

  I tried to run them in compatibility mode, using all variants. and also I tried soome of advice from the help article about the disk drivers. game discs are clean and one striped.

  Why can I install the program and access the drive to use the files it contains, but then not use the disk?

  Hello
   
  
  This problem may occur if one of the following conditions is true:
  a. you do not use the game disc to start the program.
  b. the CD player is not compatible with the program.
  c. using a copy of the program CD.
  d. you are not connected to the computer as an administrator.
  e. the programs interfere with the start of the game which is running but is invisible to you.
  f. the CD-ROM drive uses out-of-date drivers.
   
   
  I would ask you to try the methods listed in the article below:
  Error message or the game stops responding on the "Loading" screen when you start a Microsoft game: "insert the right CD.
  http://support.Microsoft.com/kb/228985/en-us
  
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• When I boot computer I get this message... Remove the c:/System Volume Information directory. EFaDATA\SYMEFA. DB-log is corrupted and unreadable

  Original title: damaged and unreadable

  When I boot computer I get this message... Remove the c:/System Volume Information directory. EFaDATA\SYMEFA. DB-Journal is damaged and unreadable... How to fix this?

  Thank you very much for your help.
  I discovered the new external hard drive was the problem. Formatted as NTFS seems to be a problem so I reformatted to FAT and the problem disappeared.
  The error message was: the journal of System Volume Information EfaData SYMFA DB file or directory is corrupted and unreadable.

  Thanks again.

• When runing the system restore, I get a message says, "System Restore did not complete Sudessfully" the reason why it gives States "an unspecified error occurred during system restore.

  When I was runing the Sytem Restore I get a message that says "System restore was not completed successfully" the reason he give said "an unknown error occurred during system restore.

  Problems with system restore:

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  1. If you use Norton (Etc), disable it before using System Restore. info at the link above.

  2. try SR in safe mode:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  3 Malware will stop at the system restore:

  If necessary, do all the workSafe Mode with network.

   

  To get intoSafe Mode with network, press F8 at the Power On / boot and use key arrow upward to get intoSafeMode with networking from the list of options, and then press ENTER.

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight.

  See you soon.

  Mick Murphy - Microsoft partner

• When I try to use the Snipping Tool I get a message saying that "the capture tool doesn't on your computer right now. Restart your computer and try again. If the problem persists, contact your system administer. "__What I can do to fix this? __Thanks

  When I try to use the Snipping Tool I get a message saying that "the capture tool doesn't on your computer right now. Restart your computer and try again. If the problem persists, contact your system administer. »
  What can I do to fix this?
  Thank you

  Hi Palaimo,

  See if one of the patches in the following link works for you.

  Snipping Tool fails

  Ramesh Srinivasan, Microsoft MVP [Windows Desktop Experience]

• When installing Lightroom 6 I asks me to enter the serial number, I get a message that we do not endorse serial number

  When during the installation of Lightroom 6 I asks me to enter the serial number, I get a message that it is impossible to endorse the serial number.

  What should I do?

  Hi Porpora60,

  I am locking this discussion, because a duplicate exists here: Lightroom6 installation code does not work.

  If you were unable to solve the problem by using the troubleshooting steps in the links provided, Ned please Contact customer via chat to confirm your correct series number.

  Best,

  Del

• I use LR cc and when I try to use the feature up, I get a message back indicating that "no connection found Upgright". I do not have ' had this problem in the past. IM using Windows 10 and I used a Canon 7 d Mark II with an II Canon 24-70 lens. No idea wh

  I use LR cc and when I try to use the feature up, I get a message back indicating that "no connection found Upgright". I have not had this problem in the past. IM using Windows 10 and I used a Canon 7 d Mark II with an II Canon 24-70 lens.

  It simply means that it cannot find enough information in the image to apply a correction. Have you tried to apply a profile and then using the vertical transformation.

• When I click on the address bar, I get a message that "internet explore has stopped working". ?

  When I click on the address bar, I get a message that "internet explore has stopped working".  After that it stops working, it reopens to my homepage.  Sometimes it is OK, but usually, I need to go get put in a website and go that direction.

  Hello

  Try resetting Internet explorer.

  From the below link you can use Microsoft fix it to reset IE.

  http://support.Microsoft.com/kb/923737

• I try to download my paid for 13 elements upgrade. When I click on the "Download" button, I get this message: 413 header length too large

  I try to download my paid for 13 elements upgrade. When I click on the "Download" button, I get this message: 413 header length too large.  Help?

  You can download it by using the direct download link, which I predicted.

  Download Photoshop Elements products | 10, 11, 12, 13

  During installation, when prompted enter the serial number and to proceed with the installation.

  If you had purchased the update serial number.

  First, enter the serial number Photoshop elements 13.

  Then it will ask for the previous qualifying version number.

  In the drop-down list, select Photoshop elements 12 and enter the serial number Photoshop elements 12

• When I re-startup I get a message "no available boot device - HDD internal.

  Original title: start the problem.

  Recently, my computer hangs in.  Sometimes, when I re-startup I get a message "no available boot device - HDD internal. Can someone tell me what this means? (Doesn't look good!)

  This probably (should) means that your hard drive is dying

  Try this if you can initialize

• I have an epson stylys photo printer - rx680 series. When I try printer I get err message, (open unit and removal to scan paper, I did but til do a printer)

  stylys photo printer - rx680 series.  When I try printer I get err message, (open unit and removal to scan paper, I did but til d)

  Hello

  Thanks for posting the request in the Microsoft community forum.
  You have reached the right forum for your question.

  1. don't you make changes on the computer before the show?
  2. What is the exact error message?

  You can try the steps in knowledge base article and check.

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Try to update the latest driver on the manufacturer's Web site and check.
  http://www.Epson.com/cgi-bin/store/consumer/consDetail.jsp?OID=63069505

  
  Just reply with the results. I'd be happy to help you further.

• Network Ricoh Aficio 2027 PCL 5 printer, I am trying to connect to is not on my list of printers available, and when I type in I get a message that it is not properly typed

  The network Ricoh Aficio 2027 PCL 5 printer, I am trying to connect to is not on my list of printers available, and when I type in I get a message that it is not typed correctly.

  Right Church wrong Pew. Post here instead-online http://answers.microsoft.com/en-us/windows/forum/windows_xp-hardware