When you try to reinstall hp psc 1210 all-in-one, the program is responsible for the computer, but when I try to open it a message says file inaccesable

Similar Questions

• HP psc 1210 all-in-one printer: HP PC all-in-one printer

  Printing test page fine.  Prints the first page of the document very well.  After than that, each page becomes lighter and blurred until unreadable.  This "bad s.  Printer is several years old and has been the impression so far.

  Hello @bdr777,

  Welcome to the HP community!

  I hope you have a pleasant experience here.

  I would like to help with the discoloration print issue you have with your HP PSC 1210 all-in-one printer, when printing from your computer Windows 8.1.

  Could you try to make 3 copies of something on the printer for me? If the three pages of fine print, then we know that the problem is related to the software on your computer. If the pages are starting to fade and blur, then we know that the problem is probably with the printer cartridges.

  Are the cartridges you use genuine HP? Can you check the date of guarantee on them for me if they are? If they are relatively old cartridges, the nozzles down can be a bit clogged and start getting muddy upward while you print. (This is particularly likely if you use the printer very rarely).

  If copies are still faded and blurred, try these steps to clean the cartridges:

  1. Open the all-in-one with the power on and then remove the ink cartridges by slightly pressing the cartridge while pulling gently toward you.
  2. Inspect the ink cartridge ink nozzles and contacts for the accumulation of debris and ink.
  3. To clean build-up, dip a q-tip in distilled water (or water if distilled water is not available) and press the remaining water from the swab.
  4. While now the cartridge by the sides, as shown in Figure 3 below, gently wipe off any buildup of debris.
  5. Reinsert the ink cartridges and perform the alignment of ink cartridges.
  6. Print a test page to check the ink cartridges and rinse any remaining accumulation of the nozzles of the cartridges.

  

  -Source

  If the copies to print without any problem, try to download the HP printer installation wizard to make sure you have the latest drivers for your product.

  I hope this helps!

  Please reply to let me know if we have solved the problem.

  

• When you try to open a session message a userinit.exe (oxc0000005) on Windows Vista

  When you try to open a session in systems invites a userinit.exe (oxc0000005) on Windows Vista message and appears a black page, tried to work on safe mode and restart, but does not solve the problem and won't let me in in the operating system, please notify

  Startup Repair: frequently asked questions

  Here are answers to some common questions about startup repair.

  What is the Startup Repair?

  Startup Repair is a Windows Recovery tool that can fix certain problems, such as system files missing or damaged, that might prevent Windows from starting correctly. When you run the Startup Repair, it scans your computer for the problem and then tries to fix it so that your computer can start correctly.

  If you experience problems when you attempt to run the Startup Repair tool, or if your computer does not have the Startup Repair, your computer manufacturer can have customized or replaced the tool. See the documentation provided with your computer or go to the manufacturer's Web site.

  How to use Startup Repair?

  Startup Repair is located on the System Recovery Options menu, which is on the Windows installation disc. Startup Repair can also be installed on your drive hard if your computer has preinstalled recovery options. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.

  If you have a Windows installation disc:

  1. Insert the installation disc. If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer.

  2. Restart your computer.

     Click the Start button, click the arrow next to the button lock and then click on restart.

  3. Choose your language settings, and then click Next.

  4. Click on repair your computer.

  5. Select the operating system you want to repair, and then click Next.

  6. In the System Recovery Options menu, click Startup Repair.

  If your computer has preinstalled recovery options:

  1. Remove all floppy disks, CDs and DVDs from your computer and restart your computer.

     Click the Start button, click the arrow next to the button lock and then click on restart.

  2. Do one of the following:

     • If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again.

     • If your computer has more than one operating system, use the arrow keys to select the operating system you want to repair, and then press and hold F8.

  3. In the Advanced Boot Options screen, use the arrow keys to highlight repair your computer and press ENTER.

  4. Select a keyboard layout, and then click Next.

  5. Select a user name and password, and then click OK.

  6. In the System Recovery Options menu, click Startup Repair.

  Are there problems Startup Repair cannot fix?

  Startup Repair cannot fix hardware failures or certain types of virus attacks. It is not a backup tool, so it cannot help you recover personal files, such as photos or documents. To help protect your computer, back up your system and your files regularly. For more information, search for "backup" in Help and Support.

  What happens if startup repair is unable to solve my problem?

  If the repairs are not successful, you will see a summary of the problem and links to contact for support information. Your computer manufacturer may include additional support information.

  See also

  • What to do if Windows does not start correctly
  • What is system restore?

  Also on the screen where you choose the Startup Repair, you can also choose command prompt. Type this (it's a single line)

  Tracking Add "HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /v "Userinit" / t Reg_Sz/d "c:\windows\system32\userinit.exe".

• HP PSC 1210 all-in-one: could not open the HP Director icon to the desktop

  I installed the CD software for this fairly old printer on my laptop Windows 10 (64-bit). Everything seems to work fine except that I can't access the HP Director. I tried to check on the resources from HP site, but it does detect not all HP products on my laptop even if the printer is plugged in and on. Also, I searched for the car and the road status update on the site of HP tools. Even if I see my printer listed on the player page, it has no download button click next to my model. I was trying to see if the drive indeed download when I installed the software.  Again I don't know even though most everything works except for no access to the HP Director. I guess that the fundamental question is whether or not this now old enough (but still very good printer) can run on Windows 10. I used it before on XP. I'd appreciate any help with any of these issues. Thanks, Peggy

  Hello

  HP Director is not intended for Windows 10.

  The original CD was made several years earlier version 10 of Windows.

  Right click on the start icon and select programs and features, and then delete any software installed client the HP of your printer.

  Install the software by following the steps below:

  http://support.HP.com/us-en/product/HP-PSC-1200-all-in-one-printer-series/90763/model/90765/document/c01796879/

  Be aware that no full functionality is available for Windows 10 since it is an older model, scan and pritn base drivers are provided by the operating system itself.

  See "I have always used the HP and the HP Toolbox Solution Center. What I use now? "in the document for more information.

  Shlomi

• Error when you try to open a video or audio file using Windows Media Player-operation abandoned

  WINDOWS MEDIA NOT OPEN FOR ME!

  I recently bought a new jvc hd everio hd camera, I put the videos I recorded there from the other day that the files were .mts and he says, replace these files with .avi and it will play so I played 1 and he played really agitated then WMP just stopped working and I got the error

  C:/folder...  Abandoned operation!

  Continues to appear when I try to open any type of video or audio file now, I want to uninstall and reinstall the wmp player, but I need to know is there a way to fix this to play as it was before, I went on the net tryin to google it and search for it but im leaves loop holes saying changing the programs by default and other things but nothing worked , I need to find the right way to get this working... help me...

  Hi DragLee,

   
  Windows Media Player is the default or integrated drive in Windows Vista. It can't be uninstalled or reinstalled. However, if a system file is missing or damaged, we can run sfc (System File Checker) scan to find and fix system files corrupted.
   
  Try these steps and check the result.
  Step 1: Scan of the sfc
  1. open an elevated command prompt. To do this, click Start, click programs, accessories principally made, right-click Guest, and then click Run as administrator. If you are prompted for an administrator password or a confirmation, type the password, or click on allow.
  2. type the following command and press ENTER: sfc/scannow
  3 restart the computer once the analysis is complete.
  4. check if the problem persists.
   
  For more information, see http://support.microsoft.com/kb/929833
   
  Step 2: If the problem persists, perform the system restore to a date where the media player was working fine
  1. Click Start, type system restore in the search box, and then click System Restore in the list programs.
  If you are prompted for an administrator password or a confirmation, type your password or click on continue.
  2. in the System Restore dialog box, click on choose a different restore point and then click Next.
  3. in the list of restore points, click a restore point created before you started having the problem, and then click Next.
  4. click on finish.
   
  See which is the system restore?
  I hope this helps.

   

  Kind regards
  Syed - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I get a Parameter (valid parameters are "/" and "/ Uninstall" install) command line invalid when you try to open a saved information zip file

  When I get an email from a cell phone photo, it is saved in the download folder (which is another problem), and when I try to open it in that folder I get the above error message. I am able to open the image in the body of the email, however. I would like to save these photos in "My Documents/pictures."
  Thank you... System WIN 7

  If the image is displayed in the body to the size you want, you can save using one of these approaches:

  • image right click > Save Image as...
  • Right-click (anywhere on the page) > Page Info > media tab > choose image > button "Save as."

  To change your download folder, or activate the dialog box to allow you to choose each time, read this article: start-up, homepage, tabs and download settings.

  Does it work?

  About the error message in your subject line, I don't know what is the cause. What program do you use to Zip/Unzip?

• ShowWindow enter an infinite loop when you try to open a subfolder of a file system shell extension

  Hi all,

  I've implemented a file system shell extension. Everything works fine, but the next case: the user tries to open a subfolder of the extended file system (double clicking on its icon, for example), but an error is detected. When the ShowWindow is called to display the error message, the thread enters an infinite loop within the ShowWindow function.

  It seems that the shell access mode when double click to open a subfolder which prohibits the display of new windows.

  Have someone faced this situation? Can anyone give me a suggestion in order to investigate in the right direction?

  I thank very you much.

  Hello

  I discovered the reason for the behavior represented: I created the message window as a child of the display window. At the opening of the subfolder view window becomes disabled, which also affect the child window. Definition of the parent to NULL window I solved the problem.

  Paolo Righi

• My PSC 1210 all-in-one not Scan after the recent software update

  There is no if long software update asked me to install the last change of HP software. Which is curious, because when I look in the download, the last of them for OS10.6 section, which I run, was released in 2009.

  Before, I scanned successfully by using the Print & Fax system preferences.

  When I did it today, thogh, after choosing the option to Scan and then open Scanner, I would get the message that there is 'no scanner not selected', although HP psc 1200 series at the top of the screen. I tried scanning several times and got the same result every time.

  What can I do to get this working again?

  Hmmm, that seems strange that you will receive an update for a PSC 1210, because I do not think that there has been updates this software for years.

  Have you tried to uninstall the driver and then reinstall?

  You can find the instructions to uninstall here: http://support.hp.com/us-en/document/c02259020

  And then re-install the driver by clicking on: http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&docname=c02259020&lc=en&os=219&product=90764&sw_lang=

  Click on drivers & downloads and select your operating system (Mac OS X) from the drop-down list and click Next.  Expand the sign next to the driver - product Installation software (8) + and then download/install the driver for 10.6.

• HP psc 1210 all-in-one: after installing Windows 10 my hp psc 1210 does not scan, I get a "need WIA driver" (but it prints)

  Hello

  I installed Windows 10 about 3 days ago. The printer will print but when I try to scan I get the following error. Thanks in advance. print but when I click on Scan

  Hi @gregmalnickhp,

  I see you found the error "required WIA driver. I would like to help you today. If this helps you to find a solution, please click on the button "" accept as Solution"" down below this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  The WIA drivers are part of the Windows operating system.

  Download and try to fix the WIA drivers. If you don't feel able to do these steps, you can contact the computer manufacturer or Microsoft to solve the error WIA.

  Back up the registry first.

  How to back up and restore the registry in Windows.

  Restore default startup for Windows Image Acquisition (WIA) Type.

  If you're still having problems, I would say to uninstall and reinstall the printer software.

  Temporarily, run Antivirus software and try to scan the image.

  If there is anything else I can help you, let me know. Thank you.

• PSC 1210 all-in-one: hp psc 1210 order copy but scan and print

  Until recently the copied PSC 1210, scanned and printed.  It copies is no longer in black & white, or rather when I press the copy button, the scanning starts and the printer prints a blank page.  Without moving anything, I can scan the document (Windows Fax and Scan) and print it using the same PSC 1210 and it prints perfectly.  A color copy prints a few characters in blue/green.  No recent change in hardware or software (other than the Microsoft updates).

  Hi @will-not-copy,.

  Maybe the problem is related to the ink, especially the black ink. If I understand your description that you can scan and print again, but you are unable to copy. Copying and scanning use the same hardware components so ideally if we work so should the other. Copy and print using the same ink system so if you can print, you should be able to copy; However, the impression of the computer may produce a composite black, which means that the colors combine to make black, when copying the printer can pull out the black cartridge to produce black. That's what I mean when I say that the problem might have something to do with the he black cartridge.

  I would like to print a self-test report to see if the printer hardware can produce black ink in stand-alone mode. To print a report, use the following steps:

  1. Load the plain, white paper into the paper tray.

• Printers HP psc 1210 all-in-one

  I tried for days to install my HP psc1210 all-in-one printer on a desktop HP Windows Vista SP2 that my aunt gave me when she bought a new. First of all, I used the installation disk for my printer HP psc 1200 Series (which of course is not for Vista), everything worked except for the Director of printing. Site Web of HP said that I had to replace the Director with the Solution Center. I tried but nothing works. When I use the center of Solution and want to copy the same screen rises which made with the Director of printing, but when I try to run the copy my computer says that the printer is not connected.

  The printer is connected via a USB cable and I can print on various programs such as MS Word, Outlook, etc. I don't know what to do and I'm afraid if I don't buy a new printer, I don't want to mess up the computer. There the 1200 series in the list of printers that should work with Windows Vista.

  Thank you

  Hi wlb8227,

  If you are able to print from various programs, then you have the printer installed correctly. Here is a document on how to install this printer on a Vista computer. Let me know if you need assistance?

  http://support.HP.com/us-en/document/c00808543

• I installed Photoshop CC now when I download my older camera images in Adobe Bridge and try to open in Photoshop it says file not found

  I have two old cameras, a Canon Powershot SX40 and a Sony DSC - H2. Today, I downloaded Photoshop CC and when I try to open all the images that I downloaded on the bridge of one of these cameras, I get a message "Could not complete your request because the file cannot be found". I can see these image files in the Finder, Adobe Bridge, Illustrator and can open InDesign is. Help, what do I do to be able to open my photos in Photoshop?

  Hi rg,.

  If you have an older version of the Mac operating system, this error may result from last camera raw update.

  Refer to this link: error: 'File not found' when opening JPEG files

  Kind regards

  Claes

• When you try to open windows mail it says "Windows Mail has stopped working". The error code is COOD1198. Does anyone know how to fix this?

  Download updates for

  There was a problem with that caused it to stop working correctly.

  Your computer may run out of updates that can help improve its stability and security.

  Go online to search for and install the Important updates and recommended.

  1. Click here to access the Windows Update Web site online

  2. In the left pane, click check for updates. If updates are found, click view available updates.

  3. Select all important updates and then click install. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

     Note
     If you have activated the automatic update, you can not see important updates listed. If this is the case, the updates have already been downloaded to your computer.

  I am aware of the windows updates.

  Try to compact and repair the database and see if it suits it.  See www.oehelp.com/WMUtil/

  Also be aware of the problems caused by the installation of IE9: see www.oehelp.com/OETips.aspx#15

  And beware of interference antivirus.  See point 3 on this page as well.

  Steve

• HP psc 1210 all-in-one: my hp pc is not reconizing my printer hp after a year and a half

  Just for the last month, my printer does not appear as a device on my pc.  I checked the connections, tried to detach from the pc and then reinstall it.  I tried again today after a reboot.  I don't know where he might be my software to attempt to reinstall the printer.  Any suggestions?

  Hi @Dakota15-6-7.

  I appreciate your patience.

  I think it might be time to consider the options for the printer maintenance. I recommend that join you our technical support team. You can click on the following link to start a business: www.hp.com/contacthp/

  Once you complete the form online to build your business, you can choose among different ways to contact direct.

  Good luck

• cartridge error HP psc 1210 all-in-one

  I replaced the cartridge from the printer, cleaned and reinserted it several times. The contacts on the cartridge air clean, and the contacts inside the printer air clean.  The results are intermittent. Of course, when I remove the color cartridge I get impression black ok. I wonder if there is probably a problem with the contacts in the printer, so that even if they are clean, contacts are not deployed. Otherwise, it's a problem of internal material just with the color circuit. Or is there a way to tell. The "check print cartridge" light flashes, it is not very revealing.

  Hello Blackjackand welcome to the Forums of HP.

  First thing I would recommend would be to remvoe the cartridges and reset the power supply.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I would also follow through the steps listed in this document on Print Cartridge errors.

  If those who do not solve your problem, I'd be suggeest contacting HP directly.  You can use this Web site for information about how to contact HP properly, based on your region: contact HP worldwide.

  Please contact the HP Forums.