HP psc 1210 all-in-one: my hp pc is not reconizing my printer hp after a year and a half

Similar Questions

• HP psc 1210 all-in-one printer: HP PC all-in-one printer

  Printing test page fine.  Prints the first page of the document very well.  After than that, each page becomes lighter and blurred until unreadable.  This "bad s.  Printer is several years old and has been the impression so far.

  Hello @bdr777,

  Welcome to the HP community!

  I hope you have a pleasant experience here.

  I would like to help with the discoloration print issue you have with your HP PSC 1210 all-in-one printer, when printing from your computer Windows 8.1.

  Could you try to make 3 copies of something on the printer for me? If the three pages of fine print, then we know that the problem is related to the software on your computer. If the pages are starting to fade and blur, then we know that the problem is probably with the printer cartridges.

  Are the cartridges you use genuine HP? Can you check the date of guarantee on them for me if they are? If they are relatively old cartridges, the nozzles down can be a bit clogged and start getting muddy upward while you print. (This is particularly likely if you use the printer very rarely).

  If copies are still faded and blurred, try these steps to clean the cartridges:

  1. Open the all-in-one with the power on and then remove the ink cartridges by slightly pressing the cartridge while pulling gently toward you.
  2. Inspect the ink cartridge ink nozzles and contacts for the accumulation of debris and ink.
  3. To clean build-up, dip a q-tip in distilled water (or water if distilled water is not available) and press the remaining water from the swab.
  4. While now the cartridge by the sides, as shown in Figure 3 below, gently wipe off any buildup of debris.
  5. Reinsert the ink cartridges and perform the alignment of ink cartridges.
  6. Print a test page to check the ink cartridges and rinse any remaining accumulation of the nozzles of the cartridges.

  

  -Source

  If the copies to print without any problem, try to download the HP printer installation wizard to make sure you have the latest drivers for your product.

  I hope this helps!

  Please reply to let me know if we have solved the problem.

  

• HP PSC 1210 all-in-one: could not open the HP Director icon to the desktop

  I installed the CD software for this fairly old printer on my laptop Windows 10 (64-bit). Everything seems to work fine except that I can't access the HP Director. I tried to check on the resources from HP site, but it does detect not all HP products on my laptop even if the printer is plugged in and on. Also, I searched for the car and the road status update on the site of HP tools. Even if I see my printer listed on the player page, it has no download button click next to my model. I was trying to see if the drive indeed download when I installed the software.  Again I don't know even though most everything works except for no access to the HP Director. I guess that the fundamental question is whether or not this now old enough (but still very good printer) can run on Windows 10. I used it before on XP. I'd appreciate any help with any of these issues. Thanks, Peggy

  Hello

  HP Director is not intended for Windows 10.

  The original CD was made several years earlier version 10 of Windows.

  Right click on the start icon and select programs and features, and then delete any software installed client the HP of your printer.

  Install the software by following the steps below:

  http://support.HP.com/us-en/product/HP-PSC-1200-all-in-one-printer-series/90763/model/90765/document/c01796879/

  Be aware that no full functionality is available for Windows 10 since it is an older model, scan and pritn base drivers are provided by the operating system itself.

  See "I have always used the HP and the HP Toolbox Solution Center. What I use now? "in the document for more information.

  Shlomi

• Printers HP psc 1210 all-in-one

  I tried for days to install my HP psc1210 all-in-one printer on a desktop HP Windows Vista SP2 that my aunt gave me when she bought a new. First of all, I used the installation disk for my printer HP psc 1200 Series (which of course is not for Vista), everything worked except for the Director of printing. Site Web of HP said that I had to replace the Director with the Solution Center. I tried but nothing works. When I use the center of Solution and want to copy the same screen rises which made with the Director of printing, but when I try to run the copy my computer says that the printer is not connected.

  The printer is connected via a USB cable and I can print on various programs such as MS Word, Outlook, etc. I don't know what to do and I'm afraid if I don't buy a new printer, I don't want to mess up the computer. There the 1200 series in the list of printers that should work with Windows Vista.

  Thank you

  Hi wlb8227,

  If you are able to print from various programs, then you have the printer installed correctly. Here is a document on how to install this printer on a Vista computer. Let me know if you need assistance?

  http://support.HP.com/us-en/document/c00808543

• When you try to reinstall hp psc 1210 all-in-one, the program is responsible for the computer, but when I try to open it a message says file inaccesable

  When you try to reload my win xp with my hp psc 1210 loads of computer program, but when I try to open the message file inaccesable bed

  Installs.
  Original title: * e-mail address is removed from the privacy *.

  Hello

  Sorry for the delay. I was hoping that someone familiar with would provide assistance.

  During the installation of the software for USB printers, the printer should not be connected until requested by the installation program.

  When you download (save this file)
  http://ftp.HP.com/pub/softlib/software3/COL6316/MP-19447-3/rw2_021_w02_enu.exe
  then right-click > run, what happens?

  Don

• PSC 1210 all-in-one: hp psc 1210 order copy but scan and print

  Until recently the copied PSC 1210, scanned and printed.  It copies is no longer in black & white, or rather when I press the copy button, the scanning starts and the printer prints a blank page.  Without moving anything, I can scan the document (Windows Fax and Scan) and print it using the same PSC 1210 and it prints perfectly.  A color copy prints a few characters in blue/green.  No recent change in hardware or software (other than the Microsoft updates).

  Hi @will-not-copy,.

  Maybe the problem is related to the ink, especially the black ink. If I understand your description that you can scan and print again, but you are unable to copy. Copying and scanning use the same hardware components so ideally if we work so should the other. Copy and print using the same ink system so if you can print, you should be able to copy; However, the impression of the computer may produce a composite black, which means that the colors combine to make black, when copying the printer can pull out the black cartridge to produce black. That's what I mean when I say that the problem might have something to do with the he black cartridge.

  I would like to print a self-test report to see if the printer hardware can produce black ink in stand-alone mode. To print a report, use the following steps:

  1. Load the plain, white paper into the paper tray.

• My PSC 1210 all-in-one not Scan after the recent software update

  There is no if long software update asked me to install the last change of HP software. Which is curious, because when I look in the download, the last of them for OS10.6 section, which I run, was released in 2009.

  Before, I scanned successfully by using the Print & Fax system preferences.

  When I did it today, thogh, after choosing the option to Scan and then open Scanner, I would get the message that there is 'no scanner not selected', although HP psc 1200 series at the top of the screen. I tried scanning several times and got the same result every time.

  What can I do to get this working again?

  Hmmm, that seems strange that you will receive an update for a PSC 1210, because I do not think that there has been updates this software for years.

  Have you tried to uninstall the driver and then reinstall?

  You can find the instructions to uninstall here: http://support.hp.com/us-en/document/c02259020

  And then re-install the driver by clicking on: http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&docname=c02259020&lc=en&os=219&product=90764&sw_lang=

  Click on drivers & downloads and select your operating system (Mac OS X) from the drop-down list and click Next.  Expand the sign next to the driver - product Installation software (8) + and then download/install the driver for 10.6.

• HP psc 1215 all-in-one: I accidentally reset the settings to the printer on my MAC, how can I re - install my printer

  Hello my printer is offline so I was trying to remove and add it again, however I accidentally reset printers 'recorded' and he's completely lost. How to reconnect it? I am connected to my printer with a USB cable. My computer is a MAC and psc1215 all-in-one printer. Thank you.

  Hey there @gucuk, welcome to the Forums of HP

  I came across your post about needing help to install your PSC 1215 turn it on for your Mac running 10.10. As there are has no comprehensive software features or drivers available for this printer on 10.10, you'll need to install the printer by an update from Apple.

  Click this link for instructions: installation of a Mac printer driver using Apple Software Update

  To testify of my attempt to help you today, click the thumb below. Click on the "accept as a Solution" If the problem has been resolved it please and thank you!

  If there are problems, let me know and I'll do my best to help.

• HP psc 1210 all-in-one: after installing Windows 10 my hp psc 1210 does not scan, I get a "need WIA driver" (but it prints)

  Hello

  I installed Windows 10 about 3 days ago. The printer will print but when I try to scan I get the following error. Thanks in advance. print but when I click on Scan

  Hi @gregmalnickhp,

  I see you found the error "required WIA driver. I would like to help you today. If this helps you to find a solution, please click on the button "" accept as Solution"" down below this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  The WIA drivers are part of the Windows operating system.

  Download and try to fix the WIA drivers. If you don't feel able to do these steps, you can contact the computer manufacturer or Microsoft to solve the error WIA.

  Back up the registry first.

  How to back up and restore the registry in Windows.

  Restore default startup for Windows Image Acquisition (WIA) Type.

  If you're still having problems, I would say to uninstall and reinstall the printer software.

  Temporarily, run Antivirus software and try to scan the image.

  If there is anything else I can help you, let me know. Thank you.

• cartridge error HP psc 1210 all-in-one

  I replaced the cartridge from the printer, cleaned and reinserted it several times. The contacts on the cartridge air clean, and the contacts inside the printer air clean.  The results are intermittent. Of course, when I remove the color cartridge I get impression black ok. I wonder if there is probably a problem with the contacts in the printer, so that even if they are clean, contacts are not deployed. Otherwise, it's a problem of internal material just with the color circuit. Or is there a way to tell. The "check print cartridge" light flashes, it is not very revealing.

  Hello Blackjackand welcome to the Forums of HP.

  First thing I would recommend would be to remvoe the cartridges and reset the power supply.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I would also follow through the steps listed in this document on Print Cartridge errors.

  If those who do not solve your problem, I'd be suggeest contacting HP directly.  You can use this Web site for information about how to contact HP properly, based on your region: contact HP worldwide.

  Please contact the HP Forums.

• I have windows7, y al istalar the all-in-one hp psc 1210 all-in-one me the por decir rechaza aren't compatible con windows7.

  What hago, if me pide el windows xp?

  Microsoft proporciona soporte sitio en frances responses. A Uniform Resource Locator (URL) here is entirely of Quebec reciba soporte para para information known location. Abre el issues y su select region in the list desplegable y haga click in el boton para continue flecha.

  http://answers.Microsoft.com/es-ES

• software and star driver hp psc 1315xi all-in-One extracts full but will not load on xp sp3

  Can not find a way to get this to install. After extracting I finally found it in running %Temp%. Searching through all files and folders, trying to find the exe file. to get it to autorun, but was unsuccessful. I tried to install this on 2 different PC with xp pro sp3 but no luck.

  The solution below is from michael323 here in the Forums of HP's Support.  Make sure that you send Bravo!

  I think I have solved this problem.

  I have a PC Windows XP Pro (SP3) who has been affected by this problem.

  Immediately after that the window of 'extraction' went to 100% and closed, nothing happened.  The windows install/never display software.

  Whenever I tried it creates a log file that started with this:

  "Parsed command line: «.\Setup.exe".

  Using datfile: C:\DOCUME~1\xxxxx\LOCALS~1\Temp\7zS1293\autorun.inf

  # GetValueByLang (f-> c_str(), _T (Version), _T (LanguagesInthisCD) failed "

  System LangID = 1033.  mapped to ENU

  # The system language is ENU, but is not on our CD!

  There was other error messages after that, but they all come from lines 3 and 5.

  Something she prevented the installation program to recognize the language ENU files ARE present in this download.

  Comparing two PCs, a problem, and one that works perfectly, I saw that one who was not was AutoRun disabled through a registry setting.  I temporarily deleted this registry on the PC that wasn't and Setup launched and ran like he was supposed to.  Here are the first of this log from the same PC, a few minutes later, where the only difference was that I had removed the registry setting criminalized:

  "Parsed command line: «.\Setup.exe".

  Using datfile: C:\DOCUME~1\xxxxx\LOCALS~1\Temp\7zS1293\autorun.inf

  System LangID = 1033.  mapped to ENU

  We use the system of language = FRA, which is located on our CD!

  As you can see, the message "(LanguagesInthisCD) failed" (line 3) disappeared, and the line 5 (now line 4) shows that it has to recognize that the language ENU installation files are present.

  So if you encounter this problem, and you are comfortable with the system registry, here is how I got it to work on my PC:

  Start regedit
  Navigate to the bottom of this tree
  -HKEY_LOCAL_MACHINE
  -SOFTWARE
  -Microsoft
  -Windows NT
  -CurrentVersion
  -IniFileMapping
  Below, find out if there is a key named "Autorun.inf".
  On my PC (the one with this problem) the value of this key has been "@SYS: nexistepas".
  If your registry database also has this, it may be the cause of your problem.
  In the left pane of regedit, do a right click on Autorun.inf and select "Rename" from the context menu.
  Change the name to something like "Autorun.inf.hold".
  Close regedit
  At this point, I restarted my PC, but I don't know if it is really necessary.
  I ran the downloaded driver file.  It extracted, and the Installer started out as it was supposed to.

  When it was done, I returned in regedit and renamed "Autorun.inf.hold" to "Autorun.inf".

  It is extremely frustrating for me, and (if you need it), I hope that this solution works for you.

• PSC 1210xi All in one driver for Windows 7

  I have a PSC 1210xi all in one.  When I put in my product for downloads, the choice in "Printers and multifunction" developed as all-in-one HP PSC 1210 or all-in-one HP PSC 1210V.  I have a new laptop that is running WIndows 7.  Should what download I choose?  I have loaded the original software for HP PSC 1100 series-1200 series, version 2.1.0.  Thank you.

  Hey Kan02. You don't need to download a driver for this printer, the driver is integrated in Windows 7. Here are two options on how to install this printer:

  Option 1:

  You can follow this document to install the printer: the driver for your product is included in the Windows 7 operating system

  OR

  Option 2:

  You can use the HP utility Windows 7 printer to install.

  Both of these options should get the printer to the top and runing for you.

  Take care

  Sean

• PSC 2210 all-in-one: PSC 2210 all-in-one with Windows 10: ok printer but the scanner does not work

  
  

  Hey @Manu37520,

  Welcome to the Forums of HP Support!

  I understand that you have some problems with the scanning of your PSC 2210 all-in-one printer to your PC for Windows 10. The printer has no drivers for Windows 10. You will need to use a computer with an operating system prior to analyze.

  Please let me know if that solves your problems. If so, please click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• PSC 1610 all-in-one

  Can I e-print to my HP PSC 1610 all-in-one?

  Hi JudithAMorrison,

  Just to add some additional information for you, your PSC 1610 is not able to ePrint, as it was released before that HP has applied the ePrint technology for their printers. All new printers are usually capable ePrint, so if you are wanting to acquire a range of HP active ePrint printers, you can contact HP Technical Support at the 1-800-474-6836 and see what kind of offers, they have to get you an active ePrint printer.

  If you need anything more, please let me know. Have a great day!