Why two phones ring at the same time

Similar Questions

• My wife and I have iPhone 5 s, the two rings at the same time while we are at home when one of us Gets a call. They are on the same account, is there a way to stop this without establishing separate accounts?

  My wife and I have iPhone 5 s, the two rings at the same time while we are at home when one of us Gets a call. They are on the same account, is there a way to stop this without establishing separate accounts?

  settings - phone - call another device - off.

  One of you should get their own apple ID, you just go to have problems later.

• I recently bought a computer build-yourself. My question is what is the best way to mirror or save files on the two hard disks at the same time?

  Hello community,

  I recently bought a computer build-yourself.
  My question is what is the best way to mirror or save files on the two hard disks at the same time?
  I know there is a way in diskmgmt.msc, but I can't seem to make it work.
  Spec:
  Windows 7 Professional 64 bit
  8 GB ram ddr3
  2 x 1 TB hard drive

  On Saturday, 22 September 2012 00:53:18 + 0000, kevin.coe wrote:

  As I said, I think it's not only not a good idea, I think it's a very

  a poor man. Backup should be stored outside the computer content. Or
  use a service like Carbonite Online backup.

  Ken Blake, Microsoft MVP

  What is raid? A large number of people I know use raids.

  RAID 1 (mirroring) is not a backup solution. RAID 1 uses two or
  Several readers, each one duplicate of the other, to provide redundancy,
  no backup. It is used in situations (almost always inside)
  companies, not in homes) where any city cannot be tolerated.
  because the way it works is that if a disk fails the other takes
  more seamlessly.

  Although some people thing of RAID 1 as a backup technique, it is
  what it is, because it is subject to a simultaneous loss of the
  original and many of the main dangers facing the mirror
  your data - serious power, close to the lightning seeds, virus
  attacks, stolen computer, etc. Most companies that use RAID 1
  also have a solid plan of external backup in place.

  "Why the RAID is (usually) a Terrible idea".
  http://www.pugetsystems.com/articles?&ID=29
  Ken Blake, Microsoft MVP

• Could a NI6008 be shared by two software programs at the same time?

  Hello

  I wrote two software with Labwindows/CVI for different purposes. Two of them are using NI6008. I have only one ni6008 attached to my laptop. I can run two programs at the same time? I mean, it's a NI6008 could be controlled by two different software at the same time? Thank you!

  Best,

  Shang

  Shang,

  There are four types of tasks, AO, DIO and counter. You can have one of each performer both on a USB-6008.

  Kind regards

  Kyle Mozdzyn

  Engineering applications

  National Instruments

• How to take snapshots of two usb camera at the same time

  Hello

  I have a project where I have to take still photos of two usb camera at the same time repeatedly and save the in a particular direcltory. I am received using a camera by using "Camera Grab vi", but I can't make it work with 2 cameras, I use the flat sequence and 2 "Camerra Grab vi: with particular camera in a sequence, but each time when I run the program I get only pic of a camera, its seems a camera dominates the other.»

  Please is it possible to use the two camera simultaneously. Attached are the snapshot of my vi.

  Thank you

  Ankit G

  Looks like you are using the same reference at the same time grabbing the camera. The two camera snaps happen but the second camera clamp is written on the first so it seems alone is slam. Try to run the VI executiong highlighted arbitrary mode (select icon icons four bulb to the right of the button run on the schema). This will allow you to see the data stream. In order to get both of these Snap you'll need separate references. You can try to watch one of our examples in the example Finder OR give you some direction (LabVIEW > help > find examples > Browse tab > Input and Output material > IMAQdx > high level > Snap.vi). You can break the two cameras at the same time if you just copy this code and double of the code.
  (Note: If you change the examples, always save as copy in another location so that you do not save on the packed example)

• Trigger two FPGA instances at the same time

  I have a basic FPGA code that transmits the bits of data on a serial (RS-485) bus, the code is written so that it expects in the first State of a machine to States in a single-cycle timed loop.  After a certain trigger, he begins to read a FIFO containing data and sends the data on a line of Tx.  It does this until all bits are send and then it goes back to the first State to wait for the next trigger.  The relaxation is necessary because windows must fill out first before the FPGA FIFO can start sending.

  I need two instances of this code runs, because I have two buses of com (one is redundant).  So I use the FPGA code as a Subvi and I wrote a main FPGA vi to call two separate instances of the Subvi in parallel.  A regular window vi wrote on the FIFO for bed FIFO for Rx and Tx.  No problems so far.

  The thing is I start two transmissions in 200nS of each other (Yes, nanoseconds).  Windows will write two FIFO in parallel, but the timing is 4uS apart, too long.  I tried implementing a Boolean flag in the Subvi FPGA, but windows can not write directly on the control of Subvi.  FPGA won't allow (the Write function is grayed out).  I tried to use a FIFO for a flag, but the problem is a race condition.  One of the instances is first read FIFO and he destroy.  The other can't read.  I need a common trigger point to be used by the two instances of Subvi.

  My final solution was to use a memory in the Subvi FPGA and digital control in the main FPGA vi.  Windows write in numerical order, it may because the control is in the main FPGA vi.  Inside the main FPGA, I run a timed loop that looks for digital to be zero.  If so, it writes the value into the location of the memory used by the Subvi FPGA.  After awhile, the principal wrote a zero back to memory to prevent the Subvi is restarted, as well as to write a zero for digital to reset.  This repeats, waiting for windows to write in digital again for the next transmission.

  I had to do it this way because sometimes I want to pass on the bus, and sometimes just one or the other.  Numeric values are used to determine which to pass on.  Now, the transmissions are starting to almost exactly at the same time, 1 or 2 nanoseconds apart.  But the trigger process seems very silly to me.  I was wondering if there is a better solution.  I'm pretty new to FPGA.

  tbob wrote:

  Basically, I did the same thing using FPGA memory.  Windows I am writing for a digital control that resides inside the main FPGA vi.  In the main FPGA, I write in the memory.  Inside the Subvi FPGA, I read the brief and decode the value to use either one or the other or both buses.  After fool with it for awhile, because reading Memeory needs to use a shift register (probably because it takes a whole cycle of clock), I had to work.  The two bus trigger at the same time.  I guess it's not really important if I use a FIFO or if I use the memory.  The main problem is that I write Windows at the hand of FPGA, then the hand of FPGA for the Subvi FPGA.  Then the time is right for what is the Subvi is.

  There are some advantages to the use of two FIFO on your approach.  First of all, you don't have the change of register for the memory location.  Secondly, we should not worry that VI is responsible for compensation to the memory location, or do, you run the risk that one of your subVIs run twice, or not at all, if the memory is not erased at the right time.  Perhaps most important, you'll save yourself space on the FPGA because you will not need arbitration - the additional code that is added when two parts of the FPGA try to access the same resource at the same time.  In your case, both instances of the Subvi access the memory block at the same time, so the FPGA compiler adds additional logic to avoid conflict.  If only read you the memory block in one place and just write it in one place (reading and writing can be different loops where subVIs) there is no need for arbitration.  Using two FIFOs, you can keep independent and avoid the conflict resolution code.  See the help for the "arbitration" for more details.

• Is it possible to have two mice connected at the same time?

  Hello. I have a gamer mouse, and I am pretty tired of changing the battery every now and then. So I was wondering if I could connect a wired mouse, I could use on the desktop, while my current mouse is always connected - for when I want to do some gaming. Windows Vista will allow that I have two mice connected at the same time?

  Hello

  You can connect two mice of universal Bus controller to the computer, but it goes to show that a single pointer.

• possible to have 2 different application fields for two different clips at the same time

  Hello

  possible to have 2 different application fields for two different clips at the same time for the classification match in terms of the scope, only not to the eye?

  Not that I know of.  And Yes, it would be very useful. As would the ability to go back 2 in reading monitor and a button "game clip under the read head 1. Sigh.

  Neil

• Insertion of records in two different tables at the same time?

  Hello everyone, I have question about inserting records in two different tables at the same time, I'm looking for is by the way a unique id, which is created in the first statement insert to the second insert statement. Example of this problem:

  < cfquery name = "addRecords1" datasource = 'test' >

  Insert Into Table1 (name, Date, age)

  Values (< cfqueryparam cfsqltype = "cf_sql_char" value = "#arguments.) "Name # ' >.

  < cfqueryparam cfsqltype = 'cf_sql_date' value = '#arguments. "Date # ' >.

  < cfqueryparam cfsqltype = "cf_sql_int" value = "#arguments. Age #"(>); "

  Select SCOPE_IDENTITY() as RecID;

  < / cfquery >

  < cfquery name = "addRecords2" datasource = 'test' >

  Insert into Table2(Company,City,Date,ID)

  Values (< cfqueryparam cfsqltype = "cf_sql_char" value = "#arguments.Company #" >,)

  < cfqueryparam cfsqltype = "cf_sql_char" value = "" #City # ">,"

  < cfqueryparam cfsqltype = 'cf_sql_date' value = "" #Date # ">,"

  ( < cfqueryparam cfsqltype = "cf_sql_int" value = "How to pass RecID to insert in this table?" >).

  < / cfquery >

  In this example, I'm inserting records in table 1 and creation of IDENTITY SCOPE as RecId. I would like to pass this id and insert it in my table 2. This Id, I'll use in my second table as an identifier. If anyone knows anything about this please let me know. Thank you.

  );
  

  QueryName - DOT - ColumnName, so it should be:

  );
  

  HTH,

  ^_^

• appearing in two different colors at the same time container attached screenshot.

  Hello

  I am very impressed with this site's Look, you can see that
  in this the container showed up in two different colors at the same time as shown in the attached screenshot.

  Please tell me how to get there?

  A part is loading advertising and other view their business rules.

  Please tell me how to get this behavior

  Because when I use the Application container = 'black' background color, it displays the container integer oiail color.

  Help, please

  Thanks in advance.

  There are many ways to achieve this. We can be to use the background image for the application. Other means may be to use various containers (Panel, canvas etc with background pictures) to get this look. Think of it in HTML view. How you can use the div tags to your page layout, you can use various containers of Flex to your page layout.

• Why can't run at the same time two wmm?

  I use wmm to convert video files in 320 x 240 to save space on my computer.  A file of 4 GB maybe becomes a go.

  Hello
   
  Two instances of Windows Movie Maker cannot run on Windows at the same time as it is by design.
   
  Getting started with Windows Movie Maker: http://windows.microsoft.com/en-US/windows-vista/Getting-started-with-Windows-Movie-Maker
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Vibrator of Smartphones blackBerry and ring at the same time?

  Is it possible to have the phone ring and vibrate at the same time? Seems that when I turn the volume past "vibrator" that the phone does not vibrate when a call comes through. Now, the vibrator is not very powerful, but if I'm in a noisy place I need to vibrate to give me a chance to pick up the call.

  Any help or advice are appreciated.

  Hey i68040,

  There is a feature that you can enable for this in the settings of the phone sounds and notifications, he said vibrate in calls

  Ice

• How to display two open sites at the same time on the screen instead of switch between tabs?

  I need to open two different sites using Firefox. They appear as tabs, but I can only show a tab at a time and have continually switch back. I need to have two separate sites open and displayed simultaneously on the screen. Is there a way to do this or an add-on that will support multiple windows open on the screen?

  You can open all pages in separate windows and resize and position windows horizontally or vertically to the two visible at the same time.

  Note that you can drag a tab slightly downwards in the navigation window to tear off the tab, or use the context menu of the tab (transition to the new window).

• Is it possible to use express Airport and Time Capsule both as two Wifi-repeaters at the same time?

  Hello

  I have a time Capsule from the airport. I use it for my back ups and he repeats my wifi in the House (bottom).

  Now I need a Repeater wifi upstairs. I think to buy Airport Express. I will connect the Airport express with a Lan connection on the floor. And then I would also have wifi on the floor.

  But is it possible to use the time Capsule Airport express airport and at the same time: two repeaters-wifi?

  1. I have a Fritz! Box router / wifi (we called wifi Fritz! box)

  2. I have a time Capsule airport / wifi Repeater (we called the turtle wifi)

  3 and now I want Airport express on the floor for the wifi upstairs (another name for this wifi?)

  Is this possible?

  Before I had used TP-link (in socket), but it works for a few months.

  Thank you for your help and advice.

  2. I have a time Capsule airport / wifi Repeater (we called the turtle wifi)

  I think that your terminology wrong... the TC cannot work as a Repeater in the Frtiz.

  I think that you have done is connect via ethernet and run it as wireless... or WAP Access Point. It is perfectly great way to do it.

  3 and now I want Airport express on the floor for the wifi upstairs (another name for this wifi?)

  This is connected by ethernet, then it will work fine... you can call it Expresswifi

  You are certainly going to clutter the wireless channels, you could so be interesting rather than auto setting fastenings.

  2.4 ghz has been set to 1, TC 6 and 11 Express then Frtiz.

  5 GHz is less of a problem... auto should be fine, because the beach is mediocre.

• How I have two tabs open at the same time

  I want to work on both windows at the same time, in order to drag a symbol from one to the other

  Perhaps there is an add-on to view side-by-side tabs in the same window? Certainly, it is not built in.

  You can open pages in two separate windows and resize the windows so that they appear side by side.

  Let's say you have a window with two tabs open. If you restore the window if it is not expanded (you can see some Office behind it), then you can drag a tab from the window and drop it on the screen area to give it its own window.

  As far as I know, there isn't a way to place these side-by-side windows automatically, but you can use all the usual methods of resizing windows with the mouse to set up.