Why used the pc would I delete the songs of m USB?

Similar Questions

• Why using the typewriter in acrobat 9 adds less file size that the use of the text of the comment in acrobat 11 tool?

  Why using the typewriter in acrobat 9 adds less file size that the use of the text of the comment in acrobat 11 tool?

  Two employees, one using acrobat 9 and the other uses acrobat 11. The two employees open a secure document one page 105 KB in size. Used using acrobat 9 using the typewriter tool to add comments. Document increases in volume to 137 kb. Second employee using acrobat 11 uses the comment add the text tool (since it is no longer a typewriter tool). This employee has to use tool once and the document immediately increases size of 105 k to 950 + kb. Why is this? What can be done to avoid this?

  As I suspected much earlier, the difference is in the fonts that are used for the text. For the smaller file, text annotation font is Times Roman. that is a policy that is essentially built into Acrobat/Reader. For the larger file, the font is Tahoma, which is not an integrated police force, which ends by happens so the entire police gets embedded in the PDF file. The size of this font on disk file is 681KO on my system (Mac), and it ends up taking more space when they are embedded in the PDF file. The same type of thing happens with form fields and this is done so that all characters in the font are available when the text is changed in a system that may not have the installed font.

  One of the problems is if you try to reduce the size of the file by changing the font that used up one of the built-in ones (Courier, Helvetica, TImes Roman), Acrobat does not remove the now unused of the file font information, if you do not get the reduction in file size that you can imagine, even if the font is no longer presented as being incorporated. I submitted this as a bug some time ago, but it has not been fixed.

• Why use the symbol "!" here?

  Why use the symbol "!" here?
  If (! contactOld.getWorkAddress) .equals)
  ...
  

  public void entryUpdated(MapEvent event)
  {
  Contact contactOld = (Contact)event.getOldValue();
  Contact contactNew = (Contact)event.getNewValue();
  StringBuffer sb = new StringBuffer();
  if (!contactOld.getHomeAddress().equals(
  contactNew.getHomeAddress()))
  {
  sb.append("Home address ");
  }
  if (!contactOld.getWorkAddress().equals(
  contactNew.getWorkAddress()))
  {
  sb.append("Work address ");
  }
  if (!contactOld.getTelephoneNumbers().equals(
  contactNew.getTelephoneNumbers()))
  {
  sb.append("Telephone ");
  }
  
  sb.append("was updated for ").append(event.getKey());
  System.out.println(sb);
  }

  The "!" reverse value.

• Why use the symbol {} in the following script?

  Why use the symbol * {} * in the following script?
  < reading-writing-support-map-plan >
  < scheme name > SampleDatabaseScheme < / system-name >
  < internal-cache-system >
  < local plan >
  < system-Ref > SampleMemoryScheme < / plan-ref >
  < / local plan >
  < / internal-cache-system >
  < dumps-plan >
  schema < class >
  > class name < com.tangosol.examples.coherence.DBCacheStore < / class name >
  < init-params >
  < init-param >
  java.lang.String < param-type > < / param-type >
  * < {cache name} param-value > < / param-value > *.
  < / init-param >
  < / init-params >
  < / class-system >
  < / dumps-plan >
  < / reading-writing-support-map-plan >
  
  
  Thank you very much
  
  Published by: jetq on June 24, 2009 18:26

  Hi Frank,.

  In the example, the '{cache-name}' is supposed to be replaced by a table name or view of data that is queried for the cached data. Its purpose is show how to pass parameters to the constructor of class.

  Kind regards

  Harv

• Why used the Adobe Illustrator free trial download? How can I fix anything that's Going Wrong?

  I click on "Download trial" for Illustrator on the Adobe while website that logged into my account. He asks to open creative cloud and I click 'OK' but nothing then load it in the 'Applications' tab in the creative clouds. Nien downloads is. Creative cloud was already installed on my computer because I've used the free trial version for InDesign.

  Why is this happening? Are there not enough space on my laptop to download this app? This was very frustrating and I would appreciate any kind of help, thank you!

  I needed to update the software on my Mac

• Why use the collections?

  Please help me to better understand and to right the next point
  
  to move from a PPT available in internet, I read a sentence under the heading "Why use collections?" Please find here
  
  Use of complex data sets information to host non-PL/SQL environments using table functions
  
  I think I understand: it means that complex data sets can be collected from oracle using only a single sql statement by using the installation, called Oracle Pipelined Table functions. http://www.akadia.com/services/ora_pipe_functions.html]
  
  Is any other installation in oracle to the serveup of complex datasets of the information to the host non-PL/SQL environments?
  
  Published by: o Manjusha Muraleedas, error corrected spelling.

  I watched the presentation and here's how I read it (although you might be better to ask the author):

  Manjusha Muraleedas wrote:
  My question is, why the statement "Serve up complex data sets of information to host non-PL/SQL environments using table functions" came under the title "Why use collections?". Just because there's an installation? or any other really good news?

  There is a hypothesis that is unwritten in the presentation: "complex" data is data that must be handled in PL/SQL, because only SQL does not work.

  Nowhere the author says that a pure SQL solution should be changed into a solution of PL/SQL.

  Once you decide that you must use the PL/SQL, you might want to put your data in collections in scalar variables.

  I understand, complex data, works of art (suppose a structure with 3 columns of tables joing 5) can be meet non-pl/sql envirormment like Java, the use of the ref Cursor or xml. Collection using to do the same thing, this is not a good option.

  Again, I think that the author uses "complex" as a shortcut for 'need to PL/SQL in the first place'. If the data must be processed in PL/SQL, there is no need to use PL/SQL scalar variables or collections.
  I would say "use of the ref Cursor. Providing relational data in format XML should be the exception, not the rule. It has a cost of additional performance.

  Now lets talk about pipeline table functions.
  ...
  functions table pipeline reached the performance of parallel processing. so even if binding commodity of time and memory is there, it will be performs better than refcursors or xml?

  Pipeline table functions perform no better than the ref Cursor. There are two processes running, one to SELECT and the other for the function, there will be more work on the server. With a ref cursor, there is a fair process to return the data.

  Parallel processing is not a problem. If you can make it work in plain SQL, you can do in parallel in SQL simple.

  Published by: Ashton stew on January 22, 2013 16:44

• Why using the driver NOR-DAQmx ANSI C functions in a thread causes a deadlock?

  Firstly, apologies if this is bad advice, but it seemed the closest fit.

  I use MSVC 2008 Express with the library in ANSI C NI DAQmx for some analog output with a box USB-6009. I create a thread to handle the signal generation is based on fixed time. My main thread running the user interface. I found that I get intermittent blockages in release, so that libraries mode NOR are responsible (in the second thread) and I use MSVCRT features (on the main thread). My test code is attached as "deadlock2.cpp".

  I used WinDbg to try to find the cause of the deadlock. Traces of the battery of my two sons are attached as t1_stack.txt and t2_stack.txt.

  It seems that the MSVCRT localtime() function uses a lock when it is called for the first time and then went to lock the Windows DLL loader lock. At the same time libraries NOR (or less libraries mxs) are responsible for locking the charger DLL is being held. The mxsutils library uses getcwd() which seems to try to block something the MSVCRT and therefore my two sons are now deadlocked.

  I can probably work around this by calling the localtime() and the NOR-DAQmx functions before I spawn my second thread so that the DLLs are already loaded in the process. However, I have no guarantee of this to continue working if something changes in the future, and if there are any locks going on finally having the DllMain() calls for a thread hanging may still cause a deadlock. If my results are correct, is it likely that NEITHER would fix the dll for not trying to make something complex in their DllMain()?

  According to NI Measurement and Automation Explorer, I'm under DAQmx libraries v9.3.5f2. I download the latest version now to try, but it will take time.

  Hi dmcminn,

  Thank you for the comprehensive and detailed bug report. I was able to reproduce the problem with NOR-DAQmx 9.6 using the code you posted. I reported it to the R & D team suitable as CAR #366538.

  I agree with your analysis of the problem. Getcwd() so the first call to __tzset() acquired _ENV_LOCK, which Microsoft has documented as the "lock for environment variables. __tzset() also called GetTimeZoneInformation(), which can load additional libraries, that you have demonstrated.

  Here are a couple more possible solutions, but they are not great:

  • Link to the static version of the CRT (/ MT instead of /MD). This would bind a separate copy of the lock of the CRT table in your program, and DAQmx would continue to use the lock to MSVCR90.dll table. They use more of the same _ENV_LOCK.
  • Build using a different version of Microsoft Visual C++ (for example 2005 or 2010). MSVCR80.dll MSVCR90.dll and MSVCR100.dll own separate copies of the lock of the CRT table.

  Whatever it is, it does not eliminate the fact that mxsutils called the CRT while now the loader lock, and this function CRT acquires another lock.

  Furthermore, the forum Multifunction DAQ is a better place to ask questions DAQmx.

  Brad

• Why used the work of my Movie Clip 3D rotation tool?

  Im trying to use the tool rotation 3d for the first time. I have a picture, set as a (movieclip) symbol on its own layer. However, when I select the 3D rotation tool, it me does not change the clip. It shows me just the empty arrow.
  Could someone please shed some light on this? The only information I can find about this tool doesn't work does not correctly is if you try to manipulate an object that is NOT a clip.

  Thank you!

  Hi Sarah,.

  The screenshot shows that you have selected the 3D translation tool. Just press W to activate the 3D rotation tool (or click and hold on the Group of 3D for the suboptions tools and select the rotation tool). You should be able to use the 3D on this clip rotation after that. Let us know if there are any other questions.

  Kind regards

  Dharmendra.

• Which is better: using the NI 9203 or USB Volt to differential entrance map

  Dear all,

  I have 4 pressure transmitters, temperature transmitters 4 with output 0-10 v or 4-20 my. I have also 2 with output 4-20 flow meters my.

  I have two options:

  Is to get all the signals in my and link them to the C two modules NI 9203 or I can get 8 sensors with 0-10 V and then I can use for example NI 6218 where I can connect these signals using differential configuration. While the last two signals (of the two flowmeters) should be converted using components SSC to sell volts so that I can connect them to the same card.

  Which solution is better in regards to signal noise?

  Someone told me that NI 9203 does not support differential configuration, such as the signal of my does not noise like the Volt signal so it does no differential configuration.

  Also, NI 9203 has 0-20 my input range and the output of the sensors is 4-20 my... Is there a problem?

  Please advise...

  Yours,

  Ehab

  Hi Elijah,

  Do you mean that you have the choice between voltage and current transducers and want to know what is the best?

  Current loop 4-20 mA is intrinsically less sensitive to voltage noise.  4-20 my sources have an output impedance much higher that a shunt resistance, so that the vast majority of the noise is deleted in all of the source.  The following application note of the BAPI and our own Developer Zone article both give a good overview of the subject:

  Understand the current loops 4-20 my

  Current measurements: practical Guide

  Regarding the 0-20 mA or 4-20 mA, you will have no problem here.  4-20 mA is commonly used for sensors one reasons are that a 0 can be used to indicate a bad connection (open).

  When you take a measure of the tension, the best way to reduce noise is to measure differently, with your connections made with threads of the shielded twisted pair (Wikipedia link).  The idea here is that any atmospheric noise would affect both the + and - ends of your signal.  Since you measure differently, the noise cancel out.

  You will be probably very well in both cases.  If you use the 6218, you can provide your own external shunt resistors to measure the current, while using other channels to measure the voltage. See the article How to build a system of loop current with isolated M series.  It seems to not be updated for the 6218, but this Council provides isolation recommended for current measurement.

  The 9203 s have this integrated to the Board of Directors and are designed specifically to the measurement current.

  Other recommended reading would be field of wiring and considerations of noise for analog signals.  When setting up this system, you will need to make sure that everything is grounded correctly (without ground-loops, floating connections, etc.).

  -John

• Why use the option "automatically write changes into XMP"?

  I normally do not pull in RAW (mainly use JPEG files), to the top my catalog regularlyand do not care about interoperability with the bridge or other programs (I export only to sites Web and hard drive from time to time), so I wonder if by turning the WE option "Automatically write changes into XMP" would be beneficial for me. I've seen a few videos and read some posts recommend to enable this setting, but I'm still a bit confused about what he was going to buy me. Is there a scenario that I'm missing? Thank you.

  You are right. If you have a backup of the catalog + photos to the top you have everything you need. So if you're not from customer files or share with colleagues on different systems it would only be useful if you have stopped using Lightroom or if Adobe has changed price and you want to switch to the alternative software or something more recent, and the best is to come in the future.

• Why used the images on my office show a thumbnail preview?

  I use Windows XP 2002 and I tried to go into folder options, but there is nothing on the activation of thumbnail previews. I also went to the Windows Live Photo Gallery, but I don't see anything there either.

  Hello

  Go to the folder where you have the photos you want. Right-click and select Properties.
  Click the Customize tab. Under folder pictures, click on restore by default. You should now be able to see the thumbnails on the record.

  You can download Microsoft TweakUI from the following location to display thumbnails.
  http://Windows.Microsoft.com/en-us/Windows/downloads/Windows-XP

• When I do exp (expdp), why use the temporary tablespace?

  Dear

  Imp (impdp) is using temporary tablespace.

  but I'm not using tablespace temp, while exp (expdp) is running.

  I think that exp (expdp) will not use temporary tablespace. is it not?

  Please let me know?

  He could.  It must run queries on the data dictionary.  Some of these applications may require the temp tablespace.

  Hemant K Collette

• Why used the search box does not work

  the mag glass has a green more than and the research of features do not work at all I've tried everything I can find no answer please don't help

  Plu green indicates that the current site has a search plugin, you can install it if you want. Without doubt, who is not related to the problem.

  You are having problems with the search bar on the right end of the toolbar or from the search box in one of the internal pages of Firefox, for example the integrated home page or the new tab page?

  With the search in the toolbar bar, normally, as soon as you start typing, or if you click it with the text already in it, the button panel descends. What is happening? While you type there may be suggestions for your default search engine. You get? And finally to search you can press enter or click on the arrow. No results?

• 15 - g013cl: trying to recover a laptop using the recovery of 10 USB windows

  Hello

  My computer son had a virus that can not be deleted, so we saved all of his records and built a 10-recovery windows drive.  I ran it on his computer after he erased the inet 10 failed windows hard disk.  I thought it was a generic load (and yes I check the box when you create the recovery disk to add all files in windows).  It is a place where I can download a factory image?

  Or help with the recovery process. . I have the newspaper eerror of load that I can share

  The f

  JeffKralik

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post about your problems of recovery and wanted to help.

  HP recovery media is not available for download, instead, you must order the physical support of HP.

  We need the number of detailed PC product to see if these media are available.

  However, if this PC has been upgraded to Win10 a previous OS, the media would restore it to the original operating system, and not to Win10.

  Also, with a PC updated, if all you want to restore to Win10, you can create a Win10 installation media go to this link and do a clean install: http://windows.microsoft.com/en-us/windows-10/media-creation-tool-install?ocid=ms_wol_win10
  
  Note that when you download and build install media, the default tool corresponding to what is already installed on your PC (as in home for the House, and 64-bit to 64 - bit).  While you CAN change these settings, are NOT.  If you do, the media that results will be different and will force you to enter a NEW product code.
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• will I get the improved performance on windows xp using the pagefile in enhanced USB flash

  Lenovo 3000 J200 512 MB RAM slow operation with the new installation of windows.

  How do I do this

  Are you talking about something like ReadyBoost?

  http://en.Wikipedia.org/wiki/ReadyBoost

  That feature (and SuperFetch) are not available in XP.

  My opinion is that unless you know more about managing memory than XP, you must set the option for the paging file to the size of the managed system and just let XP take care of things.

  I read somewhere that there are none or only a performance problem minute if you can get the page file to XP on a USB key.  Keep in mind that flash drives will also be "usury" after a number of cycles of read/write so who knows how long to set up your continue to operate reliably if you were beat your USB device, day and night.

  If your system is slow, you must define what slow means for you and provide more details on your system.

  If you think that it starts too slowly: for example, I would use some software tools to measure boot time to the millisecond so that you can see exactly how long it takes, make some adjustments and measure again to see if things improve.  It allows to eliminate the human element of subjectivity in the matter.

  For example, I know that it takes my system exactly 24.03.024 seconds to start, but I have zero startup items configured at boot time.  Maybe this isn't the right configuration to everyone, but I'm all about the search for better performance.

  If your Lenovo will have more RAM, I would consider that.  512 MB is not a lot and RAM is relatively expensive, these days, and who would probably be on the best thing you could do for your system.  I can run XP with 256 MB, very good (but a bit slow), but more RAM is usually better - seek 2-4 GB if you can rotate.

  If you want someone to watch you have, follow these steps:

  Provide information on your system, the better you can:

  What is your Version of XP and the Service Pack?

  Your system have IDE or SATA disks?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  Now make some clarifications:

  Click Start, run and enter in the box:

  Msinfo32

  Click OK, and when the system info summary appears, click on edit, select all (Ctrl-A), copy (Ctrl-C) and paste (Ctrl-V) the information back here.

  For information about video drivers, expand components, click view, click on edit, select all, copy and then paste the information here.

  I have a list of your startup items will also help.  Here's a way to do it:

  So tell us what are all your startup items and we will help you to look at to see if there are some that you may not need.

  Here's a way to provide a list of your startup items:

  Download and install CCleaner here:

  http://www.Piriform.com/CCleaner

  Launch CCleaner, click on tools, startup and at the bottom right of the screen, click on the button "Save to text file" to save the startup information in a text file (name it something like startup.txt, so you can find it).

  Save the information to your desktop (or somewhere you can find it) start, open the text file with a text editor, select all of the text copy (Ctrl-A) it
  (Ctrl-C) and paste (Ctrl + V) the contents of the startup list of back here for analysis.

  Uninstall CCleaner later if you don't like (most people seem to like for it of other features).

  Here's what my startup.txt file looks like:

  That's right - I have zero startup items.  Maybe this isn't the right configuration to everyone, but I'm all about the search for better performance.