WiFi scanner

Similar Questions

• mf212w scanner can use wifi?

  Just Set up MF212W.  Can talk to the computer via wifi Scanner or do I need a USB connection?

  Ooops, did not load the Toolbox "MF".  All is well now.

• Improve the speed of the wifi at the bottom

  I have an Apple AirPort Extreme in my office upstairs. I get 200 Mbps wireless download in my office. A flight down, almost directly below my router, I have only 30-40 MB/s download. What is the best way to increase my download speed?

  You can download the app on your iPad AirPort Utility and the WiFi scanner allows to check the signal strength of your network and all competitors.

  You could do better if you have set up separate systems 2.4 and 5 GHz, and connected to the 5 GHz for 802.11ac performance, assuming that your device can support. What are we talking about here?

• Bluetooth/Hotspot tethering without cable does not work

  Hello world

  We have a weird put in place where Bluetooth does not (entirely).

  iPhone is last 9.3.3

  OSX is 10.11.4

  Setting up Personal Hotspot on the iPhone and then connecting via Wi - Fi laptop does not work. Error message "Unable to connect" standard and suggestion of using Wi - Fi diagnostics (also does not help).

  Go to Bluetooth prefs on OSX and the connection it does not work. Matching does not work, but we CAN see the iPhone. The WiFi scanner captures also the iPhone.

  If connect us the iPhone via the cable and then put in place a personal Hotspot, it does not.

  Surfing on the web, everything works. Disconnect the cable, and it stops again.

  I succeeded in pairing my iPhone to the laptop, so it seems apparent to another iPhone. I'm leaving work via cable uses a direct route via the cable which is a different connection method than live bluetooth signal?

  We have removed the Bluetooth of OSX preferences > no change.

  Reset us the iOS network settings > no change.

  Any ideas?

  Best regards, F.

  Have you looked at these?

  Share your Internet connection with Personal Hotspot - Apple Support

  iOS: System requirements for Personal Hotspot - Apple Support

  Get help with Personal Hotspot iOS - Apple Support

  Barry

• CA does not

  Hi all

  I have a Time Capsule airport as my main router (connected to a cable modem) and two extreme base stations (a "expand" and the other "bridge" mode) airport.  I have my network during the investigation and noticed recently that the TC is not broadcast a signal ac-only b/g/n 2.4 GHz and 5 GHz a/n.  I tried to reboot, check the settings (there is not a separate on the TC this setting), etc. - basically everything except factory reset.  The tool that I use to evaluate my network (WiFi, Scanner) is the list of other neighbors ac networks, so I know it's the ac detection.  Any suggestions?

  The network otherwise seems to work well.

  Thanks for your time.

  John

  Hi John

  Where are you located?

  This channel is the work of 5 GHz on?

  Please send a screenshot of airport utility, showing the wireless options.

  Do you have a separate name to 5 GHz so you can force the connections to it... and also force it to a channel that you know support AC.

  Different countries used wireless profiles will include channels without access to the CA who needs 80 mhz of bandwidth.

  Sometimes we need to force the TC both a channel and maybe even to a country that allows to avoid Apple auto configurations.

  I would test also with all other wireless off... Remove your extremes... as they may confuse the readings.

  What model are extreme, so we can see what is happening?

• iPhone 4S and the ipad 2 needs of old passwords wireless

  I changed the password wireless on my Airport Extreme 3 days. I have 5 PCs (4 windows and 1 imac), fire 2 hds, 1 samsung s5 1 android nexus 7, 1 iphone 4S and 1 ipad 2. All devices running IOS not being able to connect to my network wireless by using the new password. My iMac connects too. The iphone 4S and the ipad 2, refuse to connect with the new password, but continue to connect with the old password. My daughter has an iphone 6 and one related to the old password first. But after a few hours, his network connected and she had to reconnect with the new password.

  I see this as a security problem because the people who visited my home last year still have my old password wireless on their devices, and if their devices are old, as my iphone 4S and the ipad 2, their devices will continue to work.

  I changed the password wireless to secure my network, but he's not sure if older devices continue to work with the old password. Is this a bug in iOS? All devices are running the latest versions of iOS.

  I changed the password wireless to secure my network, but he's not sure if older devices continue to work with the old password.

  I understand that your iphone 4S and the ipad 2 is still working on the internet with the old password. You have verified this by going to a web site that you have not already visited.  Go to yahoo.com and make sure you have the last page.

  I find this very surprising.  Most of the home wifi routers only accepts the password.  Change the password on your router means iphone 4S and ipad 2 should not be able to connect to the internet.

  Are you sure that you are connected to the wifi router that you think you are?  I have two wifi routers. One of the phone company that I do not use and my own.

  You have all that you check the wifi configurations.  your router.  What is your router?  The setting on your iphone 4S and the ipad 2.  What ios version do you use?  There are problems of wifi with ios 8.  Check on one of your computers to display the wifi settings.

  on your ios device, download airport utility.  See here how to use the airport as a wifi scanner utility.  You don't need Terminal airport apple.

• How to test the signal strength of an Airport Express, which extends a network?

  I am trying to understand how my Airport Express is actually help to expand my network, and if I should move somewhere different. Any help would be appreciated!

  Current situation: my base station is an AirPort Extreme in our apartment computer room; for the internet, which is plugged into the wall. The wifi network is extended in the living room via an AirPort Express (version 7.6.4). There are on the same cabinet as the AirPort Express to Apple TV. The Airport Express has an optical cable connecting to a sound bar (which has an additional HDMI connection to the TV).

  I don't really know if the AirPort Express Terminal, he does something useful. The network is set to be extended, best I can tell: Airport Extreme network Mode is "Create a wireless network", and network Mode of the AirPort Express is "extend a wireless network. But still, the wifi on my iPad and iPhone signal strength seem to fall much in the living room. Apple TV usually broadcasts music from my desktop computer (in the computer room) well enough, but if I try to play music from my computer via the Apple Express at the soundbar, the connection is terrible and fall. (Which could be a problem with wifi, or could be an aging Airport Express question, could be a cable problem or might be a sound bar problem...)

  An example of what worries me: if I go to the Airport utility on my iPhone and a glance at the Airport Extreme, it has 4 Wireless, including Apple TV clients. But if I look at the AirPort Express, there sometimes a client wireless (iPhone), but never shows the Apple TV: even if the Apple TV is about 30 cm of the Airport Express. It's as if the 30cm distant to the Airport Express connection is weaker than the connection of two-rooms-distant Airport Extreme, but I am probably wrong that.

  In any case, is there a way to test what speed is through the AirPort Express, compared to through the extreme? I tried to use applications like CloudCheck on my iOS devices, but those only measure the speed of my network, and it is unclear whether or not he uses the Extreme or Express.

  Thanks in advance and all apologies if I used (almost inevitably) 'Express' when I should have used "Extreme", or vice versa, somewhere at the top.

  One way to see the strength of the signal is the Alt (option) key while clicking on the WiFi icon in the menu bar.

  But you see not directly related to the airport of arrival. Also the Airport utility does not give much information.

  You can see a lot more with the free app (Appstore) called "WiFi Scanner".

  The problem could be that the place you have chosen for the Airport Express can be better: it should be somewhere in halfway (in force) between the Real and where you sit with the iPad/iPhone.

• Speed max r7000 (300mbps?) problems

  Hello

  I tried Googling the shit out of this problem, play with the settings, ask reddit help, chat with a tech support person and nothing seems to have solved my problem.

  I had a lot of trouble getting decent LAN on my network speed. I couldn't go beyond 200 Mbit/s. I finally so I'm averaging around ~ 275mbps on my network through a LOT of tinkering.

  Now, it seems that the biggest limitation that I have is with the router itself. Using scanner wifi acrylic, it continues to show that my 5 GHz network only has a maximum speed of 300 Mbps. My settings are on channel 161, with "up to 1300mbps' selected. My 2.4 ghz shows 214mbps on the same network scan. I tried different channels, I tried to go down "up to 600mbps" and go back to 1300mbps no claim. I turned WMM on and outside. The connection on my test machine shows a maximum speed of 867mbps for the card wifi itself.

  I've been contemplating going to dd - wrt to see if I can play with the frequency range to see if that's the problem. Y at - it a setting or all that I need to try that I'm missing? Thank you...

  Oh, and I have flashed and reflashed the firmware, reset settings, etc., so...

  Update: apparently the problem with acrylic. I downloaded a different wifi scanner and see it 1300mbps. So I'm probably more limited by my adapter. So if someone else had the same problem, it was a superficial problem. I hope that I'll be satisfied ~ average 250mbps rates, hehe

• WRE54G v3 no SSID

  So I have a WRE54G v3 and a BEFW11S4 v2 with the latest firmware. I got the Repeater related to the router wireless with WEP at the same time.

  I can access the Repeater through the router (not connected) but does not display the SSID of the Repeater. The SSID broadcast option is on in the repetition and the router. They have the same SSID and are on the same channel.

  I can see the SSID using a scanner WiFi SSID, but it does not appear in the windows wifi scanner. My PSP is also the expander control.

  Are you able to see you wireless network name, when you search for networks wireless in range of your router? If yes then you can try to connect to your wireless network, connect once and then open the window prompt commands and ping the IP of the Expander and check if you are able to get an answer, if yes, then your expander works very well.

  You will not be able to see your Extender because the name of your network wireless router and expander control is the same, so it will show you 1 single wireless network.

• PIXMA MG6200 scanner does not work on wifi

  Hi, I'm on a Mac Book Pro OS X 10.8.5.

  I am WIFIed for my MG6200 printer scanner and print, but cannot scan. When I try, I get...

  Printer is in use or an error occurred. Check the status.

  Scan reported an error

  I tried trashing and rechoosing the printer/scanner and which do not help.

  What you're suggesting?

  Thank you

  Ty Ford

  After the clearing and reintalling new gun of the files, "printer could not be detected. during the installation. "when trying to scan.

  Again, the printer works fine, it's the scanner which doesn't connect.

  There is an orange icon lit on the edge of right front side of the printer.

  I tried scanning the Mac to the 6200. That did not work, but eventually the light orange was no longer on.

  I went back to the mac and tried scanning from there and was able to do.

  Again, it is wifi to router, Ethernet to the router to the 6200.

  Kind regards

  Ty Ford

• Canon MG5650: Canon MG5650 printer/scanner that can I print using the wifi but HP spectrum says I need to connect to analyze

  I have a HP spectrum 13 and we operate a wireless LAN at home that includes the Canon MG5650 printer/scanner. The connection between the two devices works very well generally. I can still print without problem. Today, I am not able scan - the laptop says that I need to connect to the printer to be able to do, but I am well connected via wifi, I can print.

  I turned off the laptop and rebooted. I stop the printer and restarted. No action produces a change.

  The printer is conducting the analysis. If I perform the scan at the printer operation, the scan is successful and the printer sends the document scanned to the laptop of my wife - it's the primary printer that will recognize the cannon.

  This was not a problem never before.

  I would appreciate any advice on next steps to solve the problem.

  Thank you.

  Tony

  Eventaully problem solved by adding a new application on the Canon site on the desktop and removing the old app scan supplied with the laptop. It does not explain why the problem occurred in the first place but provides a "fix."

• My iMac does not detect my C309g-m as a scanner via bluetooth or wifi.

  Somewhere between Snow Leopard and 10.7.3, my iMac stopped detecting my C309g-m as a scanner with bluetooth and wifi.  I can still print via bluetooth and wifi without problem, but "print and Scan", "Image Capture", and "Preview" not to recognize the C309 as a scanner.

  I uninstalled the HP Photo Center, but didn't know that there was a 'scrubber' option until after the forums up. Accordingly, I still have the package installed driver somewhere in the interiors of my computer.  It is a 3.3.3 package by car.

  Any help will be greatly appreciated!

  Hello

  As the software was partially removed, please follow the steps below to ensure that pilots are not damaged:

  1. open the Applications folder.
  2. go to the Utilities folder.
  3. double-click on disk utility.
  4 Select the hard disk that contains the boot volume.
  5. go to the first aid tab and select Repair disk permissions.
  Note: This process may take several minutes depending on the Mac and the amount of the permissions that need to be repaired. The journal of the progress will tell you when the process is complete.

  Then, download and install the latest HP Printer Drivers 2.8 below package:

  http://support.Apple.com/downloads/DL907/en_US/HPPrinterDrivers2.8.dmg

  Finally, reset the printing system and reconfigure the printer:

  * Be aware that reset the printer system will eliminate any existing queue and reset all custom settings driver.

  Click on the Apple menu and then click on System Preferences.
  Select Print & Scan.
  Right click (or Ctrl + click) your product with the Printers list in the left panel and then click on reset printing system.
  Click OK to confirm the reset.
  Type your user name and password.
  Click OK. The printing system resets.

  Now, click on the Plus sign and select the pritner listed as Hello in the default tab.

  Now, check if you can scan using Print & Scan or one of the other methods described below:

  http://support.HP.com/us-en/document/c01910186

  It is not supported to scan from the front panel of the printer without a full feature software, so it's expected.

  About Webscan EWS option, the page overview only scanning, in order to save the page scanned, you should right click (CTRL + left click Mac keyboard), then save the file in the contect menu.

  Please let me know any changes during the scan to Print & Scan after installing the package.

  Kind regards

  Shlomi

• Why l7780 scanner will not work on wifi?

  I have Officejet pro L7780 and the printer works fine on a connection Wi - FI, but I can't the scanner to work on a Wi - Fi connection. It works fine on USB key.

  MBA OS10.9.3,

  Welcome to the forums Onsberg,

  I saw your post on the sweeping concern you have with your Officejet L7780 unit and 10.9. The answer to your question, is that there are no scanning software or driver available for this model of printer with the Mavericks. However, there are other options you can scan that may work!

  Please see this link for the 3 methods you can choose from:

  How to perform a scan: OS X v10.9

  I hope that clarifies your question!

  Have a great Tuesday

• Canon scanner

  Opening of the early Sierra brings up a Panel for list for the user to select scanners. For me no scanners are listed. I have a Canon MG7520 that has worked well for more than a year of Apple operating.

  After checking the scanner and find WiFi and other features everything in order, tempting scan shows a report of several reasons for the failure. The last seems to appply. He says that the name of the scanner is not correct.

  Experiment, I found a work around start in the Apple preferences and go Printers and scanners. It works as follows:

  Power scanner / place the document on the scanner glass / open preferences from Apple (for the top of the screen to the left) / open Printers and scanners / scanner names listed / select or enter MG7500 Canon series 6 / Scanner screen opens (it shows a symbol of a scanner and scan of the word in its upper right) / select the area to be scanned in the new box / click the scan symbol (a form opens allowing the user to specify a name and a location for the scan).

  All this applies only to Canon printer/scanner and maybe not all of them. I imagine that Apple will correct the defect of the opening screen of the Sierra to do its job.

  You welcome any comments from the user.

  Apple - hope you're listening to.

  William foot

  [email protected]

  (1) apple may be addressed here

  Apple.com/Feedback

  (2) it is a product of canon, they can choose to support or not. Apple will not reverse engineer their OS to work for someone else's decision. the developers of Canon had access to OS X 10.12 months before it was public to make the drivers work or not, they chose to not

  (3) send never publicly your e-mail unless you want spam.

• Connect the Scanner for extreme

  Can I connect my Canon Canoscan 9000F scanner USB in the extreme I can print or scan from my MacBookAir via my WiFi?

  Unfortunately, only the print function will work in the USB port on the airport routers... If you have a compatible printer.

  Of the advanced features such as copy, scan, Fax, maintenance, etc. are not supported on routers airport on all-in-One devices or stand alone products.