WiFi with Linksys WRT610N

Similar Questions

• Cannot connect WiFi with Linksys X 2000

  Hey,.

  I have been setting up to my router wireless Cisco X 2000 recently and I have that works well for my wired connections, however for some reason when you try to use the wireless none of our smartphones to connect, unless you use a wireless guest account.

  I tried different security settings with different passwords, but none worked (WEP, WPA, WPA2,...)

  Can someone help me on this problem? I can't imagine what could be the cause.

  Firmware version: v2.0.05

  Thank you

  Karel

  Got my live chat solution:

  P: souad steps to configure the router for cable connection:
  Step 1 - Hard reset of the router to make sure that all the previous settings would be deleted, please follow the instructions below.
  1. make sure that the device is on.
  2 press and hold the reset on the back for a minute. Use a paper clip to do the reset.
  3 unplug the unit and wait another minute.
  4. turn on the device again.

  Step 2: access the configuration page.
  1. connect the main PC to port one of the router and restart it. Connect the modem to the Internet port.
  2. start your browser (for example Internet Explorer). Type http://192.168.1.1 in the address bar, and click on GO.
  3. a login prompt will come, let the empty user name, and then type the admin password.

  Step 3 - configure the router to work with your ISP.
  1. on the Configuration tab, click the tab in MAC address clone.
  2. enable MAC address Clone and click on Mac. to Clone my PC
  3. click on the button "Save Settings".

  Step 4 - customize settings the router wireless.
  1. click on the Wireless tab and set it to manual.
  2. change the Wireless network name (SSID) 'linksys' in your name you want (example: my network).
  3. set the channel width to 20 Mhz and change the channel to 11 auto wireless.
  4. set the SSID broadcast on active.
  5. click on the button "Save Settings".

  Step 5 - secure your wireless network.
  1. click on the wireless security sub-tab right next to basic wireless settings.
  2. change the security from none to WPA2 Personal Mode.
  3. type any word in the password field for and write it down.
  4. who will be the password to connect to the wireless network.
  5. click on the button "Save Settings".

  Step 6 - Power Cycle.
  a. shut down the computer.
  b. unplug the power cable of the router followed by the modem.
  c. after 3 minutes, plug the power cord from the modem back in and wait for the power led is solid before you plug the router back in.
  d. turn on the computer as soon as the power on the router light becomes solid.
  e. check your Internet connection.

  strange thing is that I put the modem this way in the first place, but without the power reset and it didn't work.

  Thanks to Christophe P for the efforts.

  Greetings,

  Karel

• Nook Color ereader & connectivity problems with router WRT610N

  I recently bought a new Nook color ereader for my wife. As long as a network administrator, I thought that this would be an easy task to configure the ereader to connect with my Linksys WRT610N router on the 2.4 Ghz band. But I'm running problems when connecting. The question seems to have intermittent connection problems where the meals seem to see the wireless network, authenicates, tries to get an IP address, then connects for a short period or removes the signal very quickly while being right on top of the router with the device.

  By the recommendations of various forums of Nook, I had the best luck with the following...

  2.4 Ghz band settings

  SSID: NookNetwork

  Channel width: 20 GHZ

  Standard channel: 9

  SSID Broadcast: enabled

  Security mode: WPA2 Personal

  Encryption: AES

  Passphrase: set out

  Key renewal: 3600

  UPNP: disabled

  RTS: default

  Defragmentation: default

  Tag: default

  However, the problem still resides in an intermittent connection to the wireless network. I also tried various arrangements of the channel to both channels 1, 6 and 11 with my best cponnecting chance to channel 9. I also played with the security and disabled all together and have plugged but always file (will not however run the unsecured network). Also try a tag value of 75, a framework of fragmentation of 2306 and 2307 RTS setting. My computer laptop while run and connect properly.

  I use the latest software updated both on the color of the corner. I am at the end and have searched high and low to get suggestions, and have not yet reached a compatible connection. Please help... Thank you! And my wife thank you in advance! Smiles!

  Mike

  Hi death,

  Thanks again for your comments and your concerns. Really appreciated!

  I took your advice and contacted Barnes & Noble for a new replacement and am waiting for the reception of the new unit as I type. If all goes well, we have reduced the problem and the replacement ends at our misfortunes... smiles!

  I'll let you know...

  Mike

• Access Internet via WiFi with E3200

  Hello

  is it possible the E3200 router to connect to internet via wifi (WLAN) interface?

  In fact I can use the ethernet port called 'Internet' to connect with my router Fritz Box (which is responsible for my internet connection to my DSL provider).

  But I don't want to use 10 m or over ethernet cable in my apartment, so it would be good to use just wifi.

  Can someone help me get this to work?

  Thank you very much.

  Lol it is not possible. It's a completely different operation mode. The E3200 has an access points wireless that accepts incoming connections from clients. You want the E3200 to connect to a different wireless access point, either you want the E3200 to customer connect to an another acccess points.

  Which is like a cell tower: it accepts connections, but it connects to the other rounds (at least not using cellular frequencies).

  This has nothing to do with the routing to this level, but only with basic connectivity.

  The E3200 with Linksys firmware requires a wired connection.

  3rd party firmware may allow you to use the E3200 as bridge or wireless Repeater same as wireless, perhaps with the FritzBox. But we have to ask in a dd - wrt forum for this.

• My IOS devices will not synchronize wifi with my MacBook air

  My devices will be simply not sync over wifi with my Macbook air. The message that appears on iPad, iPhone etc. is that they will be synchronized if the Mac is connected. I tried, but it did not work.

  "My devices will be simply not sync over wifi with my Macbook air."

  Via Wi - Fi requires the use of iCloud to synchronize data between your devices iOS a your Mac.

  http://www.Apple.com/icloud/Setup/

• to connect to a WiFi with assigned IP address?

  How do connect me to a WiFi with the IP address assigned? I configured my iPad Mini as a personal Hotspot, now I'm trying to connect to the internet using my MacBook/iPhone via WiFi network but it says the wifi network has an assigned IP address and cannot connect to internet!

  If you want to remove yourself public reactive and connect to the wi fi once more, please follow the steps:

  1. open system preferences > select network.

  2. click on the padlock and enter the user name & password.

  3. Select WiFi connected and click Advanced

  4. uncheck the box remember this network and click the sign minus.

  5. take the cursor to the menu bar top & select your network name, then click on apply and close the lock.

• can I increase my speed of wifi with settings

  Hello... I would like to know if I can increase my speed of wifi with adjustments on my computer, all parameters that would adjust my speed with my adapter BT MCard HP WLAN 802.11 b/g/n 1 x 1, thank you...

  customized HP ENVY Phoenix 245 810qe desktop PC

  Hello

  10 ten reasons why your WIFI stinks.

  11 adapter of defective material

  Your best chances for a fast WIFI connection is to use the 'AC '.  This requires that the adapter and the WIFI router two supported 'AC '.

• Unable to connect to the Internet automatically after the restart with Linksys WAG 320n

  We have a problem with Linksys WAG 320n router that after rebooting the router it does not connect to the Internet automatically.

  instead I required to connect manually by clicking on State-> Connect.

  As previously he was showing server status DNS IP addresses, now it does not appear after connecting also.

  "" Could you let me know wheather miss me an option to automatically connect with LAN "' after reboot or anything else the cause.

  Thanks in advance.

  Thanks guys...

  After changing some settings wireless - bandwidth to value 'Standard' and MTU change, its done!

  Finally, the problem has been resolved. Now I can connect automatically when I restart the router and display the DNS IP addresses too.

  Thanks once again for most people trying to help me.

  I have another question and I would like to post separately instead of mention here.

• Problem with linksys e2500 (l2tp)

  Router: linksys e2500

  WIndows: XP

  Country: Russia

  Supplier: Flex

  Hello!

  I have a problem with the l2tp connection. My provider only supports l2tp (with encryption - interference). Where can I find option to turn off encryption - scrambling for l2tp? Or how I can fix (solve) the problem.

  THX, best regards!

  thx for the answer! I have a tplink, and it solve my problem with the internet. But I need of DDNS that work only with linksys (TZO.NET). I bought the account for 1 year. My tplink does not support DDNS (TZO.NET).

  I'll try "you can try third tomato and DD - WRT firmware and see if it works" thx.

• I tried to connect wifi with my laptop, including wireless I use for a month now, but shows only 2 blue screens without the world down on the right, and he said "unidentified network".

  "Unidentified network".

  Hello, today I tried to connect to my friends wifi with my laptop, including wireless I use it for a month now and its impossible! Down right it shows only 2 blue screens without the World Cup, and he said "unidentified network"! I tried several solutions, I found online as 'install the protocols Internet 4 and 6', make sure that I have the ip auto get same restore point system and safe mode with network! Nothing works... my friend connects with his laptop and I can connect with my smartphone, except my laptop! I have windows vista... Please help me thanks

  Go to: Control Panel, Manager of Devic, adapters to extend your network, click with the right button on your wireless network and click on uninstall.

  Do not put a check in the box: remove the software driver for this device.

  Restart your computer and Windows will install your wireless network.

  If the problem persists, see if your computer manufacturer has an updated driver.

  These articles may help:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  http://support.Microsoft.com/kb/313242

• activate wifi with envy m6

  How can I activate Wifi with my laptop 1117TX m6 of jealousy?  A few days ago a technician of a mobile wireless service provider told me how to turn it off but now I have access to a Wifi connection and I can't remember how to put in operation.  I spent all day trying to find information on this at all and came to the conclusion that HP has easily the worst support scheme to simple questions from any company that I have ever met.  Can someone please help me because it makes me crazy with frustration?

  Hello D22.

  Welcome to the HP Forums!

  I understand that you don't know how to activate the wireless feature. By pressing F12 might do the trick. I would also try to connect an Ethernet cable to a router, if that doesn't help, just to be sure, that it can connect to a network.

  You can also find important information on this Microsoft Web site: why I can't find a wireless network?

  If you need additional assistance, please provide the following information:

  1. the operating system. If you need help to find this information, please visit this site in order to determine the Windows operating system.

  2. have you installed new software or drivers on this computer, before the problem appeared?

  In addition, if the question has recently arisen, I would make a system restore. I want that back you to as soon as possible to restore point. Here is a document on how to perform a system restore: System Restore

  Mario

• BlackBerry smartphone WiFi with Verizon 8330

  I have a 8330 and Verizon is my ISP.  Here, they do not provide WiFi with the phone.  The phone has this capability and can activate even if Verizon does not support?  The feature is removed models Verizon?

  There is no wifi hardware in the 8330 device.  It is not possible to get the wifi on the 8330.

• I can't make a connection wifi with my Nook Color camera using a Microsoft MN - 700 wireless router. Can someone help me with the settings that could take care of this problem?

  I can't make a connection wifi with my Nook Color camera using a Microsoft MN - 700 wireless router.  Can someone help me with the settings that could take care of this problem? I have a Dell netbook and a laptop HP working with the router so I know it works.  The Nook also works in a Barnes & Noble store it seems so that the works of Nook.  I have a similar problem with a LG Vortex phone where I can't do the wi - fi connection.

  Please post on the Support forums technical Nook for help because it is not a Windows 7 problem...

  http://bookclubs.barnesandnoble.com/T5/nook-technical-support/BD-p/nooksupport

  .. .also than that...

  http://www.barnesandnoble.com/u/nook-support-connectivity/379002491/

  Don't forget the network encryption type, IE. WPA2/WPA and key/password / password must match the wireless router/access point.

  See also this about WPA2 on the MN-700...

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/cant-connect-to-MN-700-wireless-router/1789978f-7C90-4686-A956-2d17eb79960d

• Slow WiFi with Broadcom 4322

  After upgrading my laptop HP DV7 with Windows 8, I found my wireless connection was extremely slow. My card is a Broadcom 4322AG. This seems to be the same problem as has been in the forum

  
  Slow WiFi with Broadcom 4322 and Windows 8 CP.

  Following the advice in this forum, I changed to TKIP AES security and everything seems to work properly.

  Thanks a lot for sharing your solution! My problem was that I downloaded at least 1 Mbit/s and transferred approximately 15 Mbps. Then I changed to TKIP, just as you said and now I'm moving 21 Mbps of download and 19 Mbps downloading. All this on a MacBook 5.1 :)

• How to configure the network home wiFi with dlink router

  I need to create a home network using the dlink WiFi router
  a computer with Vista and the second with XP
  can someone tell me what havo to do to configure the router etc etc o give me same informamation on where I can learn to do
  I want just the old pc with xp for the server and the vista one customer but more importantly I need the file on XP to migrate under vista.
  Thank you very muche for your end of the patient cooperation
  in return, I give free cooking classes
  see you soon

  I'm not sure if you are asking how to set up a secure wireless network, if you ask how to share files between your two computers (and there is no "customer" or "server" in a working group, in a field - which is not), or both.

  So I will give you information on doing both.

  Router - configure manually

  Setting up a router is simple enough. Normally, you run the CD that came with the router and follow the instructions. If you're running Vista, maybe the CD that came with the router does not work; I do not know this. But you can set up the router without the CD. Note that if you have Internet cable for the connection you have just set up the router to DHCP (or there may even be a choice of cable to choose). If you have DSL Internet, you select TRP usually and enter the username and password you selected when you initially set the DSL connection. So:

  1. turn off the power to your cable modem.
  2. attach a class (usually supplied with the router) ethernet cable cat5e port Internet/WAN from the router to the ethernet port on the cable modem.
  3. connect the ethernet cable cat5e from the network card in your computer to one of the ports on the router. If you do not have an ethernet cable (because you were using USB), you will need to go to the store and buy a.
  4. turn on the cable modem. After that all the lights are on, turn on the router.

  To configure the router:

  Have a computer connected to the router with an ethernet cable. Examples given are for a Linksys router. See the manual of your router or the router mftr's Web site. for the parameters by default if you don't have a Linksys. Open a browser such as Internet Explorer or Firefox and in the address bar type:

  http://192.168.1.1 [Enter] (it is default IP address of the router, which varies from router to router then check your manual)

  This will bring you to the login screen of the router. The default username is blank and the Linksys default password is "admin" without the quotes. Enter this information. You are now in the configuration of the router utility. Your configuration utility may be slightly different from mine. The first thing to do is to change the default password because * all * known default passwords for different routers.

  Click the Administration link at the top of the page. Enter your new password. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE. Re-enter the password to confirm it, and then click Save settings at the bottom of the page. The router will reboot and show you the box of connection again. Do not fill in the user name and put it in your new password to enter the configuration utility.

  Now, click on the link wireless at the top of the page. Change the network name (SSID) wireless by default to something, you'll recognize. I suggest that my clients not use their surname as the SSID. For example, you might want to name your network wireless network "CastleAnthrax" or similar. ;-)

  Click on save settings and when you get the prompt that your changes were successful, click the wireless security link which is just beside the Basic Wireless Settings link (where you changed your SSID). Most computers purchased during the last 4 years have the wireless hardware that will support WPA2-Personal (also known as WPA2-PSK). This is the desired encryption level. If your wireless hardware is older, use WPA. Don't use WEP, because who is easily broken within minutes. So go ahead and set the Security Mode WPA2-Personal. Do this and enter a password. For example, you could use the password ' here be dragons, beware you scurvy dogs! The password is what you enter on all computers that are allowed to connect to the wireless network. MAKE A NOTE SOMEWHERE THAT YOU WILL NOT LOSE.

  At this point, your router is set up and if the computer that you use to configure the router will normally connect wireless, disconnect the ethernet cable and wireless of the computer should see your new network. Enter the password that you have created (exactly as you wrote it with all capital letters and punctuation) to join the network and start surfing.

  Networking

  Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Excellent, comprehensive, but easy to understand article on sharing files/printer under Vista. Contains information about sharing printers and files, and the folders:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  For XP, start by running the Network Setup Wizard the on all machines (see warning in section A below).

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, it means which allows file sharing / print on the Exceptions tab normally run the XP Network Setup Wizard will take care of this for these machines. The only "witch hunt", it will turn on the XPSP2 Windows Firewall. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  XP - configure Windows to login automatically (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  Vista - Start ORB > Search > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  D. Si one or more of the computers is XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. XP Home does not share the users directory or the Program Files, but you can share folders inside those directories. A better choice is to simply use the Shared Documents folder. See the first link above for more information on Vista sharing.

  F. you have the job of file sharing (and tested by exchanging a file between machines), if you want to share a printer connected locally to one of your computers, share of this machine. Then go to the printer mftr Web site. and download the latest drivers for the correct system. Install them on the target machines. The printer must be collected during the installation procedure. If this isn't the case, install the drivers and then use the Add Printer Wizard. In some cases, printers must be installed as local printers, but it is outside this response.
  MS - MVP - Elephant Boy computers - don't panic!