Windows 7 does not update after changing the BIOS battery

Similar Questions

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

• Satellite Pro L40 does not start after changing the BIOS settings

  Changed some settings in the bios last night and now when I boot I get a screen black lights flash and hard drive lights up but nothing on the screen.

  There is no password on the bios... How would a BIOS reset to normal?

  I put a windows disc now, I hear the disc spin but nothing on the screen

  (I think that I have come to the right place on the forum)

  It s a Toshiba Satellite Pro L40 model psl4be.

  Thank you

  > There was no bios password... How would a BIOS reset to normal?

  You can set the default BIOS ONLY inside the BIOS access BIOS by pressing F2 or at the beginning of the initialization of the order

  But I doubt that this problem is related to the BIOS.
  Maybe it s just a simple bad luck that this problem happened exactly after change something in the BIOS.

  Try connecting an external monitor and check if you can see something on the 2nd screen.

• HARD does not work after changing the disk partitions recovery media creator

  Hello world

  After installing windoows 8.1 April major upgrade (win 8.1 presents as OEM), and have shrunk C partition to create a data partition "D", "Troubleshooting" option under advanced start menu is no longer available.

  Toshiba Recovery Media Creator does not work, too (it can not find any hard disk recovery partion).
  I got in the OEM recovery partition.
  I am also able to create a recovery using the Windows tool unit.
  You have no idea about it?

  Thank you very much!

  Hello

  Sorry to hear about all this. Unfortunately, you now have a big problem. I don't understand why you didn't create support of recovery before you started to change the factory settings, including to change the structure of the partitions of HARD drive.

  Mobile offered with factory settings a structure specific partitions and recovery recorded image is saved on the partition of drive specific and marked with invisible markers. These markers are visible for preinstalled Toshiba recovery media creator tool and when you start the tool can find points of reference and has full access to specific files.

  Unfortunately, after changing the original scores structure Toshiba tool cannot find these markers more and is not able to copy files from recovery media recovery. What you need now is the original recovery disk. Using this disk, you can install original recovery image and after doing this, you will have new factory settings.

  I know it sounds stupid now but you must order the original recovery disk and it can be done on https://backupmedia.toshiba.eu/landing.aspx

  If you have any other questions you are welcome.

• HP laserjet p1006: does not print after changing the toner

  I just changed the toner. The green light is on, but when something I send to the printer to print, the orange error light. Before inserting the toner, I pulled the Strip in transparent plastic attached to an orange tongue and the black cloth. I tried to reinsert the toner and turn on/off the printer again. Help please if you can. Thank you!

  Hi @cindycb,

  Welcome to the Forums of HP Support! I read your post and to see that when you try to print after changing the toner, the Attention light. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Make sure all the orange, packaging material is to remove the toner.

  Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  Try and print a self-test on the printer hardware to see if it is a hardware or software problem.

  Open and close the cover five times quickly. It should print a page with black lines on it.

  You can find the flashing light distribution in this document and the right solutions for the reason that you are experiencing, lights blinking on HP LaserJet P1005, P1006, P1007, P1008 and P1009 Printer Series.

  You use Genuine HP Toner?

  Please let me know the result and if there is anything else I can help you. Thank you.

• Satellite L650d-120 does not load after upgrading the BIOS 1.7

  After upgrading the Bios up to 1.70 my laptop is no charging current, but always works to the AC adapter.
  Can I do something on my own?

  Hello

  First of all, you should set the BIOS to default settings and need to save the changes.
  You must also leave the AC adapter plugged into the laptop for a longer period of time.

  Welcome them

• gSynchit does not open after changing the password

  GSynchit has stopped working. I changed the password of email account, but the program does not open if I can change the settings.

  Hello

  1. what operating system do you use?

  2. What mail client do you use?

  3 did you receive an error message when you try to run gSychit

  If you use windows7, I suggest you follow the link and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• System does not boot after changing the appearance settings

  I installed XP Home successfully, but the resolution of the screen to be changed. When I followed the instructions of troubleshooting, I was unable to get to the drivers. I changed the settings on the advanced screen prompt to auto, and now after the Windows XP logo load and it I hear the hard drive running, the next screen is completely white/black. Help!

  Is this the same solution for: in the advanced options of monitor, I selected "do not use this device"?  I tried to update the driver for the monitor and reach for straws when the button 'update driver' has been 'grayed out' (not available).  I have a new HP 2009 flat screen and have just installed XP on a new hard drive.  Monitor worked, although some resolution.  The type of monitor has been defined as "default monitor" and driver is VgaSave.  Thank you!

• Tecra A3 does not work after changing the power settings

  I changed my power settings in my tecra a3 laptop and now it does not start correctly. wants to start but just keeps going back to press F2 or F12 it please help.

  Hello
  where did you changed them? In the BIOS or in the Toshiba HW setup?

  I suggest you go into bios after turning on your machine. You have to hit just F2 Ant then in the search for bios for setting "all default setting" or something with "bios setup defaults" to reset your bios settings.

  After that, your computer should start up again.

  Welcome them

• My copy registered and checked for XP Pro SP3 does not start after changing the motherboard. Second problem is that I can't find my original install of XP Pro disc.

  After failing to find the source of reliable performance from my PC, I decided to bite the bullet and replace the motherboard, memory and the CPU. I installed a triple base 435 Athlon and a motherboard Gigabyte MA74GMT. Awarded PC again started the first time - but Windows will not, I get a number of options but none work - safe mode brings up several lines of messages on the partition of multi (0) disk (0) rdisk (0).

  A previous post suggested that a similar message meant some kind of malware but if I replace the old motherboard, processor and memory Windows works very well - in fact I use it now.

  Do I have an option but to reinstall Windows from a CD? Otherwise I have a problem - I can't find the installation discs for each piece of software except my Windows XP Pro! I do repair discs?

  Thanks for your help.

  Hi DaGeLi,

  · Provide us with the complete message you receive.

  Follow the methods below:

  Method 1:

  You were able to start the first time, you can try to boot to the last known good configuration and check the results. Link to get the procedure please refer to: how to start your computer by using last good known Windows XP Configuration:http://support.microsoft.com/kb/307852

  Method 2:

  If it doesn't then you can follow the procedure from the below mentioned link. As you do not have the Windows XP CD you can follow the procedure if you have already installed on the computer to recovery console

  How do I recover from a corrupted registry that prevents Windows XP startup:http://support.microsoft.com/kb/307545

  Otherwise, you may need to make the boot floppies. See the link for the procedure below:

  http://support.Microsoft.com/kb/310994

  You can also contact the manufacturer of the system to get the Windows XP CD.

  For reference: how to fix a computer that does not start:http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx#2

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think

• VCenter Service does not start after changing the port number

  Hi all

  Accidentally, I changed the port number for the Vcenter server from the portal of VCenter 10443 and dint realize that the Java application uses 10443 so.

  Could not start the server vcenter service, because its raise an error saying 10443 port is already im currently byt used another application.

  I tried to stop the Java service, in order to start the vcenter service and make changes to port again, numbers but I am unable to stop the java application.

  Please, if anyone knows how to change the number of Vcenter via config port or any other way, please throw a comment... Its much appreciated.

  Thank you

  Nirmal

  If you use the MSSQL database, locate WebService.Ports.http in the VPX_PARAMETER table and change to the correct port.

• vCenter WebClient does not work after changing the field of vCenter Server

  Hi all

  I had to migrate my vCenter to a new domain. This migration is smooth without any problems. Everything works fine.

  Now, some of my colleagues need to use the web Client and I discovered, after to be authenticated successfully to the web server,

  I have an error message:

  Unable to connect to vCenter Inventory Service - _ https://vcenter._olddomainname: 10443

  Thus, even after reinstalling the Web server on my vCenterServer (version 5-update1) component, it always uses old domain information.

  I can't find where to change it.

  Hope you can help me with that.

  Thanks in advance,

  Frank

  Have you tried to run the command as shown in register.bat

  http://pubs.vmware.com/vsphere-50/index.jsp?topic=%2Fcom.vmware.vsphere.install.doc_50%2FGUID-9C65879E-7442-46E2-9A20-A858B2800D12.html?

• T530 does not start after upgrading the bios to V2.65

  Hello..

  I flashed the Bios to V2.65 under Win 10 via Lenovo Systemupdate.

  After the restart I had set default Bios and save the changes.

  Start the laptop it hang in a window to select the boot device.

  When I press on my Samsung SSD EVO nothing happened.

  I'm trying to reinstall the Bios with boot-CD. Tool said: there is no need, organic cause is real.

  Downgrade to old Bios in possible (?) not...

  It please can someone tell how to fix this?

  It comes to my work machine, and this is a disaster!

  Thanks MajorM

  Hello..

  found the solution...

  > Disable menu security-> "secure starting".

  > Start menu: UEFI/Legacy Boot-> legacy set or both

  too long, I remember. I never had problems with the bios updates.

  but it was my last... never touch a running system

  See you soon...

  MajorM

• Black screen, high regular of underscore on the left does not start after reflashing the BIOS F.38 on HP2000-363NR

  HP2000 363NR, recently tried flashing the BIOS F.38 (here: http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116227-1&cc=us&dlc=&lc=en&o... ) to solve a problem of overheating.

  Well, it was a mistake.

  Now it does not start at all.

  Fans spinning upwards. Hard disk rotates.

  By pressing ESC, F1, F2, F9, F10 and F11 at startup to give appropriate (fast!) messages but then go to the same place:

  Black screen with flashing underscore in the top left. Leave it to this screen has no effect.

  Never see no text except the quick messages in the lower left (or "Press the ESC key for the system menu" down left based on nothing).

  Out and the relocation of memory does not work. Boot with a DIMM module does not work. Now hold power for one minute while the battery and plug on does not work.

  Battery is fully charged.

  OS is Windows 7 64 bit Home Premium, came with the laptop.

  Is it possible to return this BIOS?

  -Me

  Thanks to Xraytim in the post below, short-circuit the battery CMOS me returned to the previous BIOS. Need to remove card system as a whole to achieve this * beep * connector, but 34 screws later (34 = some # between 15 and 50), BIOS is back, problem solved.

  Thanks for the forum!

  -Tim

  http://h30434.www3.HP.com/T5/notebook-lockups-freezes-hangs/DV9858ca-won-t-boot-after-BIOS-update-won-t-power-with-AC/TD-p/555547

• HELP... z400 will not start after changing the BIOS settings

  Hello

  I went into the BIOS and changed all the PCI slots to include 'calculate' so now it does not recognize video card, now it does not start far from enter the BIOS to undo changes. Ive pulled the battery, reset the CMOS button and jumped the pins CMOS won't default. To b e there is a way to fix it... Please any ideas will be appreciated.

  Hi Glenn,.

  Thanks for posting your query in Microsoft Community.

  Important: Change BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  I recommend you contact the manufacturer of the PC for the procedure for making changes in the BIOS.

  Do not hesitate to write to us in case you have any problems/concerns while working on your computer, we will be happy to help you.