Windows7 - error msgs & MGP works does not properly after changing drive letter

Similar Questions

• Photosmart HP 6510 B211a works does not properly after power failure

  Hi guys,.

  I'm new to this forum, but I hope someone can help me.

  I have a HP all in one Photosmart B211a 6510, which worked like a dream, since I had last winter. We had an unexpected outage yesterday however and once the power came back, the printer insists on the fact that there is no ink in the system. I fear the worst and believe that his brain can be somewhat blurred.

  I have two of your ink cartridges replaced last week with genuine HP ones and everything was fine. My ink level is almost low on the other two, but I have not replaced these yet because it is not necessary.

  Once the power came back, the printer informed me that the magenta ink was 'missing or damaged '. I removed the cartridge, cleaned with distilled water and dry. Once replaced, the printer has changed his mind and told me all the ink cartridges are now 'missing or damaged '. When I opened the printer again, the transport of ink is automatically did not move as usual to allow me to change or remove the cartridges.

  More the touch screen of the printer does not allow me to leave this error message or perform any other function such as cleaning the heads. I tried a soft reset and hard reset, but this proved unsuccessful.

  He's tired? Should I just throw it and head to the stores again?

  Thanks for reading this,

  Fatiha

  Hi rich,

  I replaced the cartridge magenta yesterday and my printer works successfully again! Woohoo!

  My father, an electrician, so between us we have come to the conclusion that when the power came back after the crash there was an electric pick or insufficient tension than normal and this has damaged the chip of the nearest power - the magenta cartridge ink.

  All is well again in any case.

  Thanks for your help - I appreciate it

• G4-1303AU of the HP Pavilion: HP my laptop works does not properly after installation of window 7ultimate 64-bit

  This laptop is provided by UP Govt (INDIA). I installed windows ultimate 64-bit, 2 days ago and installed all the drivers. But there are two pilots who is errors. These are some

  1)PCI device- ERROR IS- the drivers for this device are not installed. (Code 28)

  Hardware ID is

  PCI\VEN_10EC & DEV_5209 & SUBSYS_3564103C & REV_01
  PCI\VEN_10EC & DEV_5209 & SUBSYS_3564103C
  PCI\VEN_10EC & DEV_5209 & CC_FF0000
  PCI\VEN_10EC & DEV_5209 & CC_FF00

  2)Ethernet Controller- ERROR IS - the drivers for this device are not installed. (Code 28)

  Hardware ID is

  PCI\VEN_10EC & DEV_8136 & SUBSYS_3564103C & REV_05
  PCI\VEN_10EC & DEV_8136 & SUBSYS_3564103C
  PCI\VEN_10EC & DEV_8136 & CC_020000
  PCI\VEN_10EC & DEV_8136 & CC_0200

  My main problem is this laptop is hangig too permanently. I do not know what is the exact reason and how do I... Its heating not so it's null chance of warming... I want to get rid of this problem of hanging. Please give me link to download the real drivers and the solution for this problem of hanging... As it was not hangig earlier on Windows 7 Home Basic (provided by Hp)

  Hello:

  Here are links to the drivers you need...

  PCI\VEN_10EC & DEV_5209:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-103100-1&cc=us&DLC=en&LC=en&OS=4063&productOid=5280050&sw_lang=&product=5280049

  PCI\VEN_10EC & DEV_8136:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100079-2&cc=us&DLC=en&LC=en&OS=4063&productOid=5280050&sw_lang=&product=5280049

  The only suggestion I can offer regarding the laptop works is not so good is to download and install the drivers for the chipset amd from the link below and restart.

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064

• Libraries works does not properly after Downgrade to Windows 7 of 10

  Demoted from 10 to 7 through "Go back to Windows 7" in the control panel-> update of the security & -> Recovery Windows 10. Everything seemed successful, having problems with scheduled tasks (but that's another issue, see reference).

  All my libraries are present and at first glance seem to work fine but I was making a few mistakes in some of my apps used regularly when you access files in libraries. So I decided to track down the mystery and I think it's related to the path of the file property - for example, the path begins with something like:

  '\\?\Volume{31BFC97B-09A1-11E3-8C84-806E6F6E6963}\ '.

  I think that this is related as:

  -When I double-click a video (thanks to my video library) my playlist video application (which should list all the videos in the current folder) displays a list of "\".

  -When I try to transfer files (via Teracopy) I get an error message "widepathmax" four times for each file transferred, and despite all the success, it's very annoying and boring. I've disabled Teracopy and tried again to transfer, but native file transfer has not yet shown upward. All works well when do not transfer files using libraries.

  Any help will be greatly appreciated

  (Reference: http://answers.microsoft.com/en-us/windows/forum/windows_7-update/task-scheduler-multiple-image-is-corrupt-or-has/6205cb04-a749-4f4f-a5be-632e01989158)

  Hello!

  Have you created custom in addition to the default libraries?

  To restore the default libraries, right-click on 'Libraries' and choose ' Restore default libraries.

  You can try to remove one of the custom libraries and create them again and include folders in the libraries manually.

• Acer X 1930 works does not properly after the factory restore

  It did not work correctly since the restoration of my desktop Acer X 1930 under Windows 7. Now, it shows: "configuration of the Windows updates failed. Returning from the changes.

  Could someone please help?

  Hello, I had problems even when I went back to 10 Win7... The only way I could make it work just is for the first few newspapers in I had to restart my system rather often. I know that this is not a SOLUTION but is what I did...

  Load Windows 7, let the updates for about 3 minutes... I first tried 8 mins but still many updates. So 3 works for me... I am also connected on wire on a Giga lan with Ultra fast connection to my ISP... So time could vary for you...

  After 3 minutes, I had 20 to 26 update ready to be used. Restart the computer. They worked. Makes about 3 times. ON the 4th time I down load 90 updates to see if it would work. And he did very well. Then after that, I went to look at the missing updates to ensure that they were going to update or had... added some that were OPT... on on the last 50ish and they have all updated very well. But for some reason, if I let all try them and update from the beginning, they would fail. I think it's because they have tried to put in the updates before others will want that needed to be done first...

  I do not work for Microsoft or Acer and it is only first hand from one of my systems. This isn't a fix only my way to make it work.

  So if you have a connection interent fast and no more wireless I would say that for the first time you start your computer just let it run for a few minutes then go to the Start button and restart so you do a little at a time...

  I would like to know how it works for you...

  James

• BlackBerry App Whatsapp works does not properly after the upgrade of the operating system 10.3.1.1565

  Hello

  After upgrade to OS 10.3.1.1565, I have problems with Whatsapp: when I get pictures, they download more in the photo folder and even I can't open them Whatsapp. They just stay inside the talk of whatsapp fuzzy mode. Advice to solve this problem?

  Thank you and best regards,

  Chris

  On my side, suddenly this problem disappeared... without do me whatever. Strange, but at least it works.

• WIFI doesn't work does not correctly after driver update

  I have a DESIRE 4 laptop 1023tu with operating system Windows 8 PRO. My WIFI works does not properly after the update drievr.

  Problems...

  1. When you try to connect to a wifi hotspot the quick adapter turns off and allows the card instantly

  2. after connected, sometimes no internet access and the problem turns off only after reconnecting to the netwrok after setting off.

  If the update doesn't work not for you then do as I explained in my previous post and roll back to the previous driver. This philosophy can be applied to all updates.

  If there is no pressure or emerging reason to update to your PC or laptop works just great... do not update. (this is especially true when it comes to an update of the BIOS)

  For your question #2, the problem could be your wireless (modem, router or access point) which causes the connection dropped.

  Best regards
  ERICO

• OptiPlex 755 USFF does not start after changing the cmos battery

  I have a desktop Optiplex 755 USFF requiring the cmos battery to replace. After the replacement of the computer will not start. It brings up the menu windows start, the sasfe mode, safe mode with network set mode command prompt, security, last know good configuration and boot normally. Any option will bring to the top of the WIndows XP loading screen and then re-boot of the computer right back to the start screen. A big loop. I can get the hard drive to boot in an Optiplex GX280 without problem. I was told of the motherboard needs to be replaced, but I changed the units of the system and the same thing with this hard drive.

  I tried to reinstall the operating system and get all the way to "starting windows" and then the blue screen stop error message 0x0000007B (0xF7A10524, 0xC0000034, 0x00000000, 0x00000000) dead. The computer is WIndows XP SP3, 1 GB of ram with 80 GB hard drive. It seems that the Setup program does not recognize the hard drive.

  Any help would be appreciated.

  After several hours of experimentation, I finally found the correct BIOS settings in order to get the computer to boot. There are three BIOS settings that need to be changed or check settings by default so that it can work. SATA 0 must be activated, SATA operations must be changed from AHCI, ATA and in the modular Bay, by default "far-sighted" should be replaced by the IDE. Save the settings and start the computer to the right upwards.

• Pavilion dm3-2020eo does not start after change of RAM

  As the topic says my computer does not start after a change of the RAM.

  I've updated 2 x 2 GB 2 x 4 GB DDR3 SO - DIMM 204pins Rams. When I start the computer after installing new RAM does nothing, all I get is a black screen.

  According to the Spec computers, it should be able to take up to 8 GB of DDR3 RAM.

  Can someone help me?

  Thank you
  Leo

  Here's the key:

  We're working on two sockets and one does not at all.

  You have a bad memory module. It happens very rarely, but it's not impossible to get a new stick of bad memory. Get the replaced bad and I think you'll be fine.

• SWF animations works does not properly during export to PDF from InDesign

  I use InDesign CS5 and you have created a document that I want to add interactivity and animations to. I created buttons and page destionations, etc., which all work perfectly when you export to PDF, but the simple animation that I wanted to include do not work. The animations were created in InDesign, then exported as a SWF file and then imported selection placed in InDesign and then exported as an interactive PDF where animations either do not work, have not been picked up or gift does not work as it should. What I am doing wrong, how can I get the animations work properly?

  First of all, if you care about your audience, stop using SWF that has now

  ZERO support on mobile devices.

  However after that make sure that InDesign is fully patched, I would recommend

  Place the SWF file in the PDF file in Acrobat Pro instead.

  Bob

• Photoshop CS6 works does not properly on a MAC using Yosemite 10.10.4.

  I've recently updated to Yosemite in MAC OS X 10.6.8. My photoshop CS6 does not work correctly. The quick selection tool work very irregularly. I have to constantly move forward and backward to the selection tool to get to tools to work at all. None of the tools or keyboard shortcuts still work correctly. I uninstalled the Design Standard Suite and reinstalled several times. I also upgraded to the latest upgrades of the applications of this suite of inside Photoshop. I am at a loss. I contacted Adobe and I was told to download a version as a result of Design Standard and install this. I did this and it helps did ' t. Any help would be appreciated. I'm in the middle of a design project and need my Photoshop to run correctly. Other programs Adobe, Acrobat X, CS6 Illustrator and Indesign CS6 seem to work correctly.

  Thanks for any help,

  Mary Pat

  Here is the link for anyone else who may run on the thread: Menus, shortcuts, Lasso tool, or Photoshop constantly run when using a Wacom tablet. Mac OS

  Benjamin

• < iframe > works does not properly in IE9

  Hi guys,.

  I designed and developed a website for a client. He asked that we put 3 international clocks that synchronize with our South African time displays the time in 3 other countries. He has actually provided tag < iframe > a site that does this without having to write JavaScripts for clocks and I came down with. I used the < iframe > tags and it works perfectly in browsers on 4/5 that I tested (Firefox 5, Navigator, Safari and Chrome), but for some strange reason it does not work 100% in IE9. It displays the correct time, but the image of the real clock is not rendered. It displays the time under the name digital instead of analog time on an analog clock like on the original site and the other browsers.

  Any of you know if it's just a setting in IE that can be changed or does not recognize the HTML5 < iframe > tags? Any help will be appreciated.

  Thank you

  Owen

  I tested in my IE9 on Vista and it works fine.

  You can view any Flash content in IE9?

  Nancy O.
  ALT-Web Design & Publishing
  Web | Graphics | Print | Media specialists
  http://ALT-Web.com/
  http://Twitter.com/ALTWEB

• Paragraph styles works does not properly on the table

  I placed a table created in Word, and then on the application of my paragraph styles.  However, not all my styles work fine.  Specifically my style of Description of the tool which includes a nested style.  The nested style does not follow the rules, given that it is.  The name of the tool should in Helvetica Neue Condensed Medium (in uppercase) while the next Description the en dash should be Helvetica Neue Light Condensed (normal caps).  On the contrary, it seems that the middle is applied randomly in the whole of the description.

  Also, when I apply my style request said I find myself with a lot of pink highlighted text implying that the police is missing when it is clearly not column.  This could be due to the recommended symbol?  Any advice on how to work around these issues?  See the picture below which shows the two questions.

  miz_nrg wrote:

  I do this in Word or CO-OPERATE?

  InDesign. You should be able to clear overrides from the paragraph Styles Panel menu.

  Check for character styles applied, you don't want to, also, if something is still wobbly.

• HP Envy 360, model 15-U363CL: Synaptics Clickpad setttings works does not properly in Windows 10

  Synaptics Clickpad v. 19.0.12.95 settings are not saved after Windows 10.  Every time I have stop and restart Win 10, I have to disable "TAPPING" I hate go in the settings of the mouse/clickpad.  Settings have been saved on close and worked well in Win 8.1.  HP needs to come with a new driver.   In the meantime, I guess I might have to go back to 8.1 win?

  Anyone else having this problem?

  Software and driver results for:

  HP ENVY x 360-15-u363cl (ENERGY STAR)

  Synaptics TouchPad Driver 18.1.7.52 Rev.A 188,0 MB 17 July 2015

  You must use Win 8.1 driver as driver Win 10 is not available for the touchpad.

• Games works does not properly in my acer aspire ultrabook s3

  Hello

  in my acer aspire ultrabook with 4 GB of RAM configuration, processor i5 s3 intel, 2 GB card of the games high-end graphics as Euro Truck Simulator 2, NFS most wanted 2012, God of War 2 will not work correctly. Animations and videos on implementing market works without lag, but when the game comes to our similar sound control ' it works well then gal once again it works well and is lagging. I have troubleshooted the games with all means possible, and I also checked for updated drivers. It is up to date. Please suggest the solution for my problem

  Hello Ruth,.

  Thanks for posting your query on the Microsoft Community.

  According to the description, the games is late by playing.

  I suggest you to follow the below methods and check.

  Method 1: Run the clean boot.

  Place your system in the clean boot state helps determine if third-party applications or startup items are causing the problem. Check this question in the clean boot state.

  Reference: How to perform a clean boot in Windows

  http://support.Microsoft.com/kb/929135

   

  Note: After the boot minimum troubleshooting step, read the sections "How to reset the computer to start as usual after a clean boot troubleshooting" in the link provided to return the computer to a Normal startup mode.

  If the problem persists, try Method 2,

  Method 2: Uninstall and re - install the latest drivers for the graphics card in Device Manager.

  To uninstall a device

  1. Open the Device Manager.
  2. Double-click the type of device you want to uninstall.
  3. Right-click on the desired specific device, and then click Uninstall. You can also double-click on the device and then on the driver tab, click Uninstall.
  4. In the confirm the device removal page, select delete the driver for this device if you also want to remove the package from the driver store device driver.
  5. Click OK to complete the uninstall.

  Note: To reinstall the driver, I recommend you to restart the computer and it will automatically install.

  Hope this information is useful. Please let us know if you need help with Windows.