withdrawal of endpoint symentech

Similar Questions

• Session of endpoint on Cisco ISE 2.1

  Hello

  I installed 2.1 ISE with patch 1.

  I have a question about the session on Cisco ISE calendar.

  If a n receives an Access_Accept message for an endpoint, ISE installs a session that is visible on the Live session section.

  If endpoint disconnects from the network, which is the time-out for this session?

  Is it possible to set this timer?

  I try to put an end to the session with the CoA on Live Session Action, but this action fails because my switch does not support cost.

  So I reboot Cisco ISE and after its reloading, the session is deleted.

  In a case that it is not possible to use the feature of 'end', is it possible to delete the session in some other way?

  Thanks in advance

  Antonio

  Hi Antonio,.

  • Completed sessions are cleaned up 15 minutes after the end.
  • If there are authentication, but no accounting, these sessions are deleted after an hour.
  • All idle sessions are cleaned after seven days.

  But your n should send account opening and stop the message for the best operation.

  For the manual uninstall, you can use under method as shown in the link I pasted. You can consult the section "withdrawal embusked sessions.

  http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-4/api_ref_guide/API _...

  Also, you might be interested in the discussion below:

  https://communities.Cisco.com/thread/61587?start=0&TSTART=0

  Kind regards

  Kanwal

  Note: Please check if they are useful.

• Do I lose all the iMessages that have not been delivered to my iphone if I withdraw (from iMessage) my phone number? My current iphone is broken and I am planing to get a new one, with in a few months.

  Do I lose all the iMessages that have not been delivered to my iphone if I withdraw (from iMessage) my phone number? My current iphone is broken and I am planing to get a new one in a few months.

  You may lose everything.  iMessage, like most e-mail services, don't keep permanently undeliverable messages.  They only keep in the short period send queue (I don't know exactly how much time but some Apple tech sites indicate no more than 10 days to two weeks) until they are purged.  That's pretty standard as otherwise, large volume, messaging services would be sitting on tera-bytes of messages not delivered each month.

  You actually have to change my phone number?  If not, let alone sign and only in iMessage when you have the new phone with this set of numbers upward to the service.

• Plant - FF 38.0.5 and version 39.0 crash Firefox; about Websense Triton AP - Endpoint DLP?

  Nice day

  FF version 38.0.5 and 39.0 fall by opening the first Web site. Version 37.0.2 works very well.

  While doing some research, I think that the problem is with Websense Triton AP - Endpoint DLP.

  In my case and many others that I've seen in various reports of incidents, the failed module is QIPCAP. DLL.

  I use Websense Triton AP - Endpoint DLP version 8.0 Build 2081.

  ID: dfe4ea5a-6efa-4215-b8b5-ff1992150703
  Signature: qipcap.dll@0x7d21

  Thanks a lot for your help!

  I contacted my Ministry of security of the company.
  While they did not me with the code to disable Websense DLP Endpoint, they confirmed that there is a known issue.
  They asked me to run the FF 37.0.2.

  Thank you
  pdmozilla

• 33.1 incompatible Firefox with Symantec Endpoint Firewall

  This morning, I received a message from Firefox indicating that a new version (33.1) Firefox is available - so I took the auto-update feature. Since the update, I found that Firefox can no longer connect to the internet. Suspect a firewall issue, I disabled firewall Symantec Endpoint and found that Firefox suddenly worked again. Since it is a working PC, I have to keep the active firewall (and I like to do anyway). Symantec does not seem to have any ability to add individual programs as exceptions. We have the ability to allow all IP traffic, or just IP application traffic.
  The new Firefox is simply incompatible with Symantec Endpoint? Why the version that I had (33.0.3 if I'm not mistaken) would have worked without problem?
  As another detail, I would add that when I click on the handler Extension/add-on in Firefox, I see that protection against vulnerabilities Symantec 12.3.0.3 - 1 is not compatible with Firefox 33.1; I guess that's part of the problem? (And if so, should I contact Symantec?)

  Hello! Thank you for your response. Unfortunately, Symantec Endpoint does not allow the user to set individual permissions for applications (even at the level of the administrator). However I solved the problem! I realized that the version of Symantec Endpoint installed on my PC has been 12.4111.4516, and that there is a version more recent (12.5) available. My server of the company does not notify me of new versions of software available - but after I installed 12.5, everything works again. For the other user who also has this problem, even if you do not have access to 12.5, you can see if you can reinstall Symantec Endpoint to see if it works for you.

• Withdrawal right of Keynote

  Hello

  Currently, I am reproducing a topic size painstakingly manually in a box of Keynote (v6.6.2). The bottom being the old version of hard-to-edit image, the top image is the new version created with text only. These positions are a variety of lengths, of course.

  It is quite easy to nail as you can see in the top image, with the exception of the padding on the right side of the item. Because I don't want to have to manually size the width of the text box, it seems that the withdrawal of right does nothing, as you can see by the small right side of the top image, from his left side.

  Anyone know why this is the case? I'm sure it's quite a long shot, but is there a solution to what does not manually resizing the width of the text box to activate the right indent?

  

  Let me know if that didn't make sense, no more!

  Thank you

  Rowan

  Currently, I am reproducing a topic size painstakingly manually in a box of Keynote (v6.6.2).

  What does this tedious to achieve? I created something to match in a few seconds,

  Visually, the only difference between the formatting of the text is the top box is aligned to the left, the bottom box is aligned:

  

• Portege Z930 - 12 H - update of the BIOS and McAfee Endpoint Encryption?

  The update to the latest BIOS (Ver.6.70) for my laptop Portege Z930 12 H comes with the warning:

  «If you use the BitLocker Windows Drive encryption, please temporarily suspend (or turn off) before BitLocker Drive Encryption updated BIOS.»

  The same caveat applies to McAfee Endpoint Encryption, which is used on my laptop and I can * not * pause or stop? Or can I apply the upgrade of the BIOS safely?

  Thank you.

  As much I know Bitlocker isn't related to Antivirus from McAfee software and two security tools are not connected to each other. BitLocker is a tool for Microsoft Windows and McAfee is a 3rd party software preinstallation on the device.

  I found a nice how doc on the update of the BIOS.

  [How to upgrade the BIOS on Toshiba laptops | http://aps2.toshiba-tro.de/kb0/HTD9502M10000R01.htm]

• withdraw the authorization allowing you to monitor the memory usage

  I now often have either force quit, restart and started having panic 'of the core"since I agree allow Firefox CPU usage monitor. I'm still on OS X 10.6.8 on my Mac. I got no problem with anything since installing this OS X.

  However, from time to time with the latest Firefox 7.0.1 installation I think the program or my computer 'blocks' and seems unresponsive. I left active Firefox and resident on my computer last night and once again, everything will be inadmissible. I opened the monitor activity and noticed that Firefox was consuming 283 MB of real memory (now 298,6 MB) and I have this one open another tab for the Seattle Times. I withdraw my permission to allow Firefox to watch my memory usage and need to know how to delete the cookie or what ever that governs)

  Go to Firefox > Preferences > advanced > general tab and uncheck the box "send performance data" more information here.

• How can I withdraw a shared album?

  How can I withdraw a shared album?

  Sorry, but we need details

  Is this a shared album that you put in place or that you have been invited to?

  What software OS and Photos (name and version) are you using?

  LN

• USB Interrupt IN endpoint data

  I am developing firmware for a USB instrument and widely using the NI-VISA to test and debug.  I would like to be able to read the data packets that comes on the Interrupt IN endpoint during a USBTMC service request - USB488.2 (SRQ).  I think that the firmware did the right thing because this code works:

  ViSession defaultRM = VI_NULL, instr = VI_NULL;
  
  Turn off State; allow to Set mutual FUND (done) in the State of the event;
  
  BSE (event status bit) scheduled status Byte enable Register; start a
  
  order with overlap; and generate a service request (SRQ) when
  
  the operation is complete.
  
  ViByte buf [] = ' * CLS; * ESE 1; * SRE 32; : SYST:ARR:CLK 2304; * MUTUAL FUND ";
  
  ViUInt32 cnt;
  
  ViUInt16 STB;
  
  
  
  viOpenDefaultRM(&defaultRM);
  
  viOpen (defaultRM, "USB0::0x0000:0 x 0001: 0:INSTR", VI_NULL, VI_NULL, &instr);)
  
  Service request events go in the standard event queue
  
  viEnableEvent (instr, VI_EVENT_SERVICE_REQ, VI_QUEUE, VI_NULL);
  
  Launch a command with overlapping that takes awhile to finish and wait that the
  
  service request indicating that it is finished.
  
  viWrite (instr, buf, sizeof (buf)-1, &cnt);)
  
  viWaitOnEvent (instr, VI_EVENT_SERVICE_REQ, VI_TMO_INFINITE, VI_NULL, VI_NULL);
  
  When you receive a VI_EVENT_SERVICE_REQ on an INSTR session, you must call
  
  viReadSTB() to ensure delivery of future service request events on the
  
  given session.
  
  viReadSTB(instr, &STB);)

  viWaitOnEvent Gets the event, and the status byte, I read the right fixed flags (SRQ and BSE).  As the value of status byte is transmitted the USB device to the host computer in a package from the Interrupt IN endpoint, it seems that he must do this package.

  I would like to see this package.  But several things, I tried to get it from NI-VISA have so far failed.  For example, I tried to install this reminder Manager:

  public static ViStatus _VI_FUNCH interrupt_in_hndlr (ViSession vi, ViEventType type, ViEvent, ViAddr userHandle evt)
  
  {
  
  	HANDLE interrupt_in_event = userHandle;
  
  	ViUInt16 size;
  
  	VI_ERROR (viGetAttribute (evt, VI_ATTR_USB_RECV_INTR_SIZE, &size));))
  
  If (type! = VI_EVENT_USB_INTR)
  
  		Return VI_ERROR_INV_EVENT;
  If (size > 0) {}
  
  		ViPByte buf = new ViByte [size];
  
  		VI_ERROR (viGetAttribute (evt, VI_ATTR_USB_RECV_INTR_DATA, buf));
  
  		printf ("interruption-IN = data");
  
  		for (int i = 0; i)
  
  			printf ("% 02 x", buf [i]);
  
  		printf ("\n");
  
  	} else {}
  
  		printf ("data without interruption-IN! \n") ;
  
  	}
  SYSERR (SetEvent (interrupt_in_event), FALSE);
  Return VI_SUCCESS;
  
  }

  with this code

  	HANDLE interrupt_in_event;
  
  SYSERR (interrupt_in_event = CreateEvent (NULL, TRUE, FALSE, NULL), NULL);
  Install a handler for the events of interruption USB-IN
  
  	VI_ERROR (viInstallHandler (instr, VI_EVENT_USB_INTR, interrupt_in_hndlr, interrupt_in_event));
  
  	VI_ERROR (viEnableEvent (instr, VI_EVENT_USB_INTR, VI_HNDLR, VI_NULL));

  and he is never called.  I tried to put these events in the standard event queue, and the call to viEnableEvent fails.  I tried to open the: RAW device instead of the: INSTR device and who fails.

  Can someone lend me a clue?

  For interruptions of the standard USB488 subclass (related to the status of the request READ_STATUS_BYTE SRQ), interrupts are handled by VISA. So, if it is an interruption of the SRQ and you have SRQ active event, which should be raised (that you see in your example). It would be the only time wherever your USB_INTR event is raised for other types of interruptions (i.e. vendor-specific interruptions). Is there a particular reason you are trying to get the data of interruption for the standard interruptions? The only data is the status that you get with viReadSTB call anyway, right?

• Create endpoint network Stream - pre-allocation for strings

  Hello

  I would use really allocation entry mode to pre-allocate memory on my RT goal. My concern is how to allocate memory for the size of the string.

  Because of the documentation

  "pre-allocate specifies that memory allocation buffer occurs when the end point is created. Wired for the type of input data determines the amount of memory allocated for each item. If a greater element is added to the buffer during execution, the extra memory is allocated dynamically. "

  I understand that if I am wiring constant string to the category data, 40 to the size of the buffer I receive buffer to 40 channels. String but how long? A single character?

  I don't want to let the Manager of memory to run after the creation of endpoint, so I would allow large memory space (for example 40 string, 10 characters each).

  Is it possible to do constant connection string (for example with 10 characters) or I have to put my string specific to the cluster size?

  Another question of trival perhaps, is - it possible to check what size buffer was allocated by this VI?

  Kamil

  Hello

  Here is some additional information on the allocation of memory for network streams:

  http://www.NI.com/white-paper/12267/en/

  My guess is that in order to pre-allocate buffers to not scalar data types, you'll write 'false' elements of the size desired in the stream to read or to flush out these elements "dummy" bevore using the flow in normally.

  Best regards!

• Stop the VISA to send automatically the characters of endpoints on read

  Is there a way to stop the VISA to send characters to the endpoint on read? The instrument that I'm trying to contact (Olympus IX-81) requires 2 of them and it seems to be quite the hassle to implement both in a single command. I think it would be easier to write just manually with every order.

  Please do what I asked you to do in your other thread. Simply right-click on the control of the chain and it is said Normal display-display or display Hex Codes. Place a probe on the string to write VISA entry and indicate exactly what the probe has. You have the instrument and the code and here is the troubleshooting steps based. You can also turn the tracing OR in MAX and set track or report what he said. You said that he worked with MAX so a comparison with the string sent there and what the VI sends is an important step to isolate the problem.

• network flow - how to get the URL of the remote endpoint?

  Hello!

  I have a project running with a host to send messages to a target of RT (cRIO) via the network stream.  It works very well.  Now, I want to set up a feed back from the target to the host, but I'm stuck on a technicality: is it possible for the reader to automatically extract the network of remote endpoint address in order to implement the return flow?  I looked in the node property expecting to find something like "URL of remote endpoint", but I can't.   As a solution I might always have the host send its address as a message through the first stream as part of initialization, but which seems to be a shame as the target clearly already knows the address of his partner.  Am I missing something obvious here?

  Thank you very much!

  Hello

  Why do you need IP address of the host in the target?

  You need create endpoint writer on the target and create endpoint of reader in the home by giving the IP address of the target. I put what I hear in the images below.

  Point endpoint target writing:

  

  Point endpoint host drive:

  

  Maybe I'm missing something...?

  Thank you

  AREV

  CTO | RAFA solutions

  

• Cannot find the web service endpoint

  Hello

  I did a .NET dll containing a Service reference built based on a WSDL file.

  In the VS2008 solution, I also have a console to test and everything works fine. I can create the client giving endpoint corresponding to an xml node in the app.config of the DLL file as a parameter.

  To work, the console executable must also have an app.config with the same endpoint definition. Otherwise, you have this error:

  The instance of the .NET class could not be found.
  Could not find the endpoint with name 'A400TMaintenanceSOAP' and 'ServiceReference400T.A400TMaintenance' contracts in the ServiceModel client configuration section. This may be because no configuration file was found for your application, or that no element of the endpoint associated with this name could be found in the customer element.

  Now when I call the TestStand dll, I have this error and I guess that's because the end point is not defined anywhere for TestStand. I tried to copy a file of SeqEdit.exe.config next to the SeqEdit.exe with the endpoint defined (like console in my c# project), but it did not work.

  Is there a way I can make it work so I can call the sequence of the editor dll?

  I've attached my dll project's app.config file (created automatically based on the WSDL file).

  Thanks for your time.

  -Mat

  I think you may have an error in your config file. The error message says: 'Could not find the endpoint with name 'A400TMaintenanceSOAP' and 'ServiceReference400T.A400TMaintenance' contracts in the ServiceModel client configuration section', but has your config file:

  
  "bindingConfiguration = contract"A400TMaintenanceSOAP"="A400T_Maintenance.A400TMaintenance"
  name = "A400TMaintenanceSOAP" / >

  So it seems that you have the contract bad name in one place or the other (very probably in the config file). I don't think that you need the Assembly decided in this case. I think you can use a configuration file for seqedit.exe like you had originally.

  Hope this helps,

  -Doug

• Error 42 on Create Endpoint of network news reader

  I am trying to use the network stream.  I have not had any problems on my Windows System 7/LabVIEW 2011.  However, when I tried the same code on my computer laptop desk or at home (both windows 7/LabVIEW 2011), I got a 42 error trying to create the endpoint of player.

  I am very confused!  The code is similar to that in the examples, it works on a PC, but fails on the other two.  I think it's something to do with the LabVIEW installation or a configuration of Windows.  I thought that they were all set up in the same way, however.

  Does anyone have an idea of this error?  This is the code that breaks down...