WLC 2504 cannot access the GUI...

Similar Questions

• New SGE2010 - cannot access the GUI

  Hello

  With allot of excitement, I decided to buy a port of 48 x 10/100/1000 Ethernet to our company SGE2010 to get inside DHCP, DNS and net administration on metal.

  I was under the impression that the initial installation has been taken and playable, but the reality was very different. I started to connect the switch to our existing infrastructure without success. After that I tried to connect to the graphical interface to see if the configuration is turned off, but has been unable to connect (used default 192.168.1.254).  Once I disconnected the switch of our network, did a factory reset and connect a single computer to the (tried various port), and yet I could not connect.

  In the end I had to dust off an old machine with serial port and connect to the switch via the port console to see what was going on.  Configuration options in the console had to say at least minimal, but I could see that both http and https are enabled, the device ip is 192.168.1.254, disabled DHCP, VLAN 1 id, default as stacking mode system settings was on stackable (autonomous tried without success), and Layer 2 on.

  I'm very surprised that I can't connect to the webgui through a nettbrowser of the turnout, since that looks at what stage 2 in management manual. Here, it is said that you should be able to connect using one of the 48 ports.

  For those who wonder then there is no firewall enabled on the client, and this is a new installation windows xp machine that I use to connect and ie6. The switch firmware is 3.0.0.18 which is the most recent.

  I would be grateful for all the help I can get because I'm running out of options. Am I missing something or is the switch faulty?

  Hi Rafn,

  Maybe the quick start guide should indicate,

  step 1. You have defined your ethernet PC card to address 192.168.1.100 IPv4 or similar with a subnet mask = 255.255.255.0 and try this action IE7 + again. http://192.168.1.254

  Try it now, it should work, but remember that if you change the IP address of the switch to another network management for example 192.168.100.x where x is a number, you will need to change the IP address of your PC as well.

  best regards and fun Dave

• Cannot access the AIP SSM via ASDM

  CISCO recommendations below:

  Cannot access the AIP SSM via ASDM

  Problem:

  This error message appears on the GUI.

  Error connecting to sensor. Error Loading Sensor error

  Solution:

  Make sure that the IPS SSM management interface is up/down and check his IP address configured, default gateway and the subnet mask. It is the interface to access the software from Cisco Adaptive Security Device Manager (ASDM) on the local computer. Try to ping the address of management of IPS SSM IP interface on the local computer that you want to access the ASDM. If it is impossible to do a ping check the ACLs on the sensor

  ----------------------------------------------------------------------------------------------------------------------------------------------

  I've tried everything recommended above. I can ping the host ASDM the FW and the SSM-10 module. Well, I ping the host machine and the SSM of the ASDM. I opened as wide as possible ACL. I changed the IP addresses and masks several times. The management of the ASA port and the SSM and the PC are on the same subnet.

  A trace of package from the PC to the SSM shows that it is blocked by an ACL rule, and yet I opened wide.   I've seen this kind of problem before and it was solved by applying the double static NAT, but I don't know how to do that if all the IP addresses are on the same subnet.

  Tried everything, need help from high level.

  The IDM software that comes with ASDM does not support java 1.7. The portion of the ASDM ASA supports 1.7 but launch the IPS cmdlet works only with 1.6. The TAC enginner suggested that I use the IME (IPS Manager Express) which is available for free on the Cisco's (http://www.cisco.com/en/US/products/ps9610/tsd_products_support_general_information.html) Web site.

  I've been playing with it today, and so far it seems to work pretty well.

• cannot access the internet after upgrading to firefox 30.0 on windows 7

  After the upgrade to firefox 30.0 on windows 7, cannot access the internet. FF 30.0 works OK under Vista

  Sometimes it's because of your security software thinking that the upgrade may not be legitimate. You can consult this article: problems connecting to websites after Firefox update.

• Just upgraded to El Capitan and cannot access the calendar. It opens with a "Shift schedules to the server" message Can only Force Quit

  Just upgraded to El Capitan and cannot access the calendar. It opens with a message 'Moving calendars to the server.

  I cannot access all features and can be closed only by using force quit.

  Please stop calendar and also the application of reminders, runs. Force quit if necessary.

  Back up all data.

  If you synchronize some of your calendars, or reminders with iCloud, then in the iCloud preferences window, uncheck that marked calendars and reminders. You will be prompted to confirm that you want to remove your iCloud calendars and reminders of the computer. They will always be in iCloud. Re-check the boxes.

  If you synchronize agendas or reminders with another network such as Google service, please open the preferences panel Internet accounts. Make a note of the settings for calendar accounts, then delete and recreate.

  Launch schedule and see if there is an improvement.

• I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  I disabled the toolbar > > Menu button (via a right click on a PC, Windows 7) and cannot access the toolbar to add items to the sail back in. Any ideas?

  Don't see the menu bar not (File, Edit, View, history, Favorites, tools, help)?
  Turn on/off the menu bar is a new feature in version 3.6.
  (Linux and OSX see: what happened to the file, edit and view menus? )
  Windows Method 1. Press and hold the key and press the letters of the following in this exact order: V T M
  Windows method 2 Press and release the button. The Menu bar is displayed; then choose ~ ~ red: V ~ ~ iew > ~ ~ red: T ~ ~ oolbars and click on ~ ~ Red: M ~ ~ enu Bar.
  The menu bar should now be displayed permanently, unless you turn it off again using view > toolbars. Check = not displayed, NO check mark is not displayed.
  See: http://support.mozilla.com/en-US/kb/Menu+bar+is+missing

  Navigation, bar toolbar bookmarks and other toolbars under view > toolbars. By clicking on one of them will place a check mark (display) or remove the check mark (not shown).

  To display the status bar, view, and then click status bar to place a check mark (display) or remove the check mark (not shown).

  Mode full screen
  http://KB.mozillazine.org/netbooks#Full_screen

  See also:
  Back and front toolbar buttons or others are missing
  Customize controls, buttons, and Firefox toolbars

• 42RL833 - latest Firmware installed and cannot access the YouTube app

  I have 42RL833 Toshiba which is updated to the latest firmware, however I still cannot access the application on my YouTube. I get an error saying that Youtube XL is no longer supported.

  What can I do to fix this?

  > I get an error saying that Youtube XL is no longer supported.

  Google has stopped the YouTube XL service and, therefore, this service isn't available anymore.
  http://www.Toshiba.EU/innovation/generic/YouTube-XL/

  You can read details here:
  https://support.Google.com/YouTube/answer/3123170?hl=en

  It also seems that YouTube XL has been replaced by YouTube Leanback Lite:
  http://www.YouTube.com/leanbacklite
  See also:
  https://support.Google.com/YouTube/answer/3153576#

  There is also a note that if you can connect your computer to your TV, you can continue to use the YouTube TV-optimized experience by visiting youtube.com/tv.

• HP 15 laptop: laptop computer is connected to the wi - fi connection, but cannot access the internet

  Hello

  My problem is my WiFi says its connected but I can't browse or access the internet.it just tells me "unable to connect to internet computer is not connected to the internet", but my wifi says 'connected'.i tried to go to the cmd prompt and typed in "netsh int ip reset resetlog.txt c:\" goal it shows me "reset failed.access is denied .he don't s no user specified settings to be reset to zero." please "» What can I do?

  Thanks in advance.

  Hello @jerome256,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums, I would like to draw your attention to the HP Forums Guide first time here? Learn how to publish and more.

  I understand that you are having a problem with your WiFi and wanted to help you!

  You are trying to access WiFi through router?  If you are connected to your wireless network, but cannot access the internet, then the problem may be with the router.  Check that the router is connected to the internet.  If you have more than one router, then you can ensure that you are connected to the correct router.  You can also try unplugging the router for about 30 seconds, and then reconnecting it.  Please consult the following document, as it can help solve the problem for you:

  HP PC - Troubleshooting wireless network and Internet (Windows 10)

  Please let me know if this information has been helpful by clicking the thumbs up below.

  Have a great day!

• "Windows cannot access the specified device, path or file" for each X 86 application on a Windows 2003 x 64 server

  Hello

  I have a Windows 2003 X 64 server and since a week ago everything works fine.

  For a week or two when I try to run an X 86 application, I always get this error:
  "Windows cannot access the specified device, path or file.
  If I run a x 64 apps everything works fine.
  What made a mistake?
  Thank you

  Hello

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for Windows Server on TechNet. Please post your question in the TechNet forums. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• I get all the time can not download anything 'Windows cannot access the specified device, path or file. You can't have the permissions to access the have__appropriate element. »

  Original title: problems cannot do anything

  Windows cannot access the specified device, path or file. You can't have__appropriate the permissions to access the item. I get it all the time can not download anything

  Hi birdylod,

  ·         What version of the operating system is installed on the computer?

  ·         You did changes to the computer before the show?

  ·         You use Internet Explorer? If so, what version are you using?

  ·         What files you download?

  Follow these methods.

  Method 1: Performs a search using the Microsoft safety scanner.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with network and check if the problem persists.

  Startup options (including safe mode)

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.

  Method 3: Scan the file system (CFS) auditor to repair corrupted files.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  For reference:

  What to know before applying permissions to a file or folder

• I cannot access the application "contact me" when a website, get error "Default Mail Client not properly installed."

  I cannot access the application 'contact me' when a web site and receive the answer "Default Mail Client not properly installed" instead of going on the requested site.

  How can I fix this problem?

  Separated from the:

  http://answers.Microsoft.com/en-us/IE/Forum/IE8-windows_other/IE8-default-mail-client-not-properly-installed/23c2a9e1-d1fa-4a50-aeb1-90a6f2af717f

  CrystalBall © SEZ...

  Unlike Windows XP & Vista, Windows 7 does not include a default email Client. [What were thinking?]

  You will need to install a (e.g. MS Outlook;) Windows Live Mail; Thunderbird) , and then set it as a default for mail in CUSTOM (<>) article in Set Program Access and defaults of the computer , then restart your computer before any function send to or MailTo will become available.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In these forums, you will find support for Windows Live Mail: http://windowslivehelp.com/forums.aspx?productid=15

• Broadband went down for several days but was back on property that still cannot access the internet

  Went away for two weeks and return to find internet and landline phone at the bottom, contacted bt which were going out but it all came back to the top, light on bnroadband but still cannot access the internet!  Any answers please...

  Contact your ISP to solve problems.

• Cannot access the windows installer

  try to install itunes and other windows updates and I get error 643 on updates and cannot access the windows with itunes installation programs.  Is there something blocking these files that they do not work

  try to install itunes and other windows updates and I get error 643 on updates and cannot access the windows with itunes installation programs.  Is there something blocking these files that they do not work

  RE: Windows updates :
  You should be psoting in section updates from Windows:
  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  Here's the tutorial for number 643.
  Have a look while you wait for answers from the section updates to Windows.

  Windows Update error 80070643
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  Re: Itunes
  You wrote. .. Cannot access windows with itunes installation programs.
  The Windows Installer Service could not be accessed
  http://www.Winhelponline.com/blog/Vista-the-Windows-Installer-service-could-not-be-accessed/

  Questions about Apple products will be better displayed on the Apple forums.
  It is where are the experts itunes and quicktime.
  Apple Discussion: Category: itunes
  http://discussions.Apple.com/category.jspa?categoryID=149

  Discussion of Apple - installation abd update itunes for Windows
  http://discussions.Apple.com/forum.jspa?forumid=792

  Problem installing itunes or quicktime for Windows
  http://support.Apple.com/kb/HT1926

  Uninstall and reinstall itunes and quicktime
  http://support.Apple.com/kb/HT1923

  For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Since the last nights update I get now launching explorer.exe "windows cannot access the specified device, file, or the path?

  Since update of last nights, I get now launching explorer.exe "windows cannot access the specified device, file, or the path?

  Hi Jemd3,

  I suggest you to completely remove Norton of the system using Norton Removal Tool and check if the problem persists.

  Method 1:

  Maybe it's that your computer is affected by virus and malware. I suggest you run an online anti-virus scan and a scan for Malware. See the links below.

  Microsoft OneCare:

  http://OneCare.live.com/standard/EN-US/3/default.htm

  Malicious software removal tool

  http://www.Microsoft.com/security/malwareremove/default.aspx

  Get a free PC safety scan

  http://OneCare.live.com/site/en-us/default.htm

  Hope this information is useful.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Receives the following message after opening a downloaded game: 'Windows cannot access the specified device, path or file. You can not have the appropriate permissions to access the item.

  Hello!
  So I'm at the end of my rope with this one... it lasts for months, and I keep revisitng every two weeks to try and fix that and every time to be completely frustrated.  I found this forum tonight, so here goes...

  We downloaded a few games on the HP Games Web site.  We download them and everything works fine.  Then, we will open the games and this pop up error message:
  "Windows cannot access the specified device, path or file.  You can not have the appropriate permissions to access the item.

  These games used to run fine, and I have no idea why they now have problems.  We have a Vista operating system, 1 account who is the administrator, the Parental control is disabled (or if we believe).

  If anyone can please help it would be much appreciated!  We have a monthly membership to this site of game and continue to accumulate credits, but may not use it.  It makes us crazy!

  Thank you in advance!

  Hello Heathie,

  Thank you for posting.  It seems that the program is no longer on your computer.  This can happen if the game files are deleted, but the game itself has not been uninstalled correctly.  I recommend you to download the game again to a location on your computer where you can easily find and install it.  This should fix the problem.

  Please let me know if this helps you.
  Zack
  Engineer Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.