WLC 5508 w / 1042-initial Setup Question

I have to do an installation from scratch and was looking for some suggestions as a basis for the configuration. I have a 5508 I have to belay 6509.

I have to get up 16-1042 model APs.  I will support many customers - scanners of bar codes, phones, iphones and laptops with WPA2.  I have to create 2 local networks without wire - one for DATA and for a hotspot.

Does anyone have a basic configuration that they can share for both the WLC and 6509 configuration?  Someone at - it a 'from' scratch version doc process they could share?  Someone at - it a version of code recommended?

I downloaded the 7.0 Configuration Guide but was hoping to get some guideance real world also.

TIA,

Amir

Hello

Well, from version 7.0, is the last it is good to start from it.

First implementation of 5508:

http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html.

I advise you to read carefully this section which explains the details and best practices to configure WLCs ports and interfaces.

Regarding the config guides, I advise you to go through the design guide:

http://www.cisco.com/application/pdf/en/us/guest/netsol/ns279/c649/ccmigration_09186a00808d9330.pdf.

And examples of configuration:

http://www.cisco.com/en/US/products/ps6366/prod_configuration_examples_list.html.

They are valid for all WLC models.

They are based on the configuration and very good examples.

HTH,

Tiago

--

If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

Tags: Cisco Wireless

Similar Questions

  • Wireless converged access (new) Mobiliity between WLC 5508

    Hello

    I have 3 WLC 5508 which is upgraded to version 8.x and I can see this feature when searching on the web I find that this new feature is necessary when we have new models of WLC 5760 or 3850 in the network and must contact 5508.

    So my question is in my current scenario, I only 5508

    1. can I activate this function and use this function between 5508 - If Yes, in the configuration, I just create mobility than in the old configuration groups and it should work right or is there additional configuration is required?

    Also in my network current fflexconnect is activated and allow this will affect my flexconnect?

    Please notify.

    Kind regards

    Anjaz

    If you want to, you can migrate to the new mobility without any problem, but must be allowed to all of your WLC at the same time. This will have no impact for your flex-connect communication or configuration and influence the way in which the tunnels between of WLC are under construction. No changes are necessary in this configuration either.

    Please rate helpful messages... :-)

  • STROKE (Application Visibilty Control) on WLC 5508 7.5 do not display data

    Dear all

    My WLC has problem...

    the STROKE is not display data (graphic or otherwise)

    I have already set up two Wlan id with the visibility control, but two of them do not display data...

    Here is my setup place WLC 5508...

    My WLC running on OS 7.5

    pack 1.0 protocol version

    NBAR engine 13.0

    AUS 6.0.182.0

    Cisco controller) > see the version of the Protocol-pack stroke

     

    Protocol STROKE Pack name: Protocol Advanced Pack

    Protocol STROKE Pack Version: 1.0

     

    (Cisco Controller) > show stroke engine version

     

    Version of the engine STROKE: 13

     

    (Cisco Controller) > show sysinfo

     

    Name of the manufacturer... Cisco Systems Inc..

    Product name... Cisco controller

    Version of the product... 7.5.102.0

    Bootloader Version... 1.0.1

    Retrieving Image Version field... 6.0.182.0

    Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27

    even from CLI still do not display data

    (Cisco Controller) >Show stroke statistics upstream applications top

     

    Perspective of the STROKE is 0 for all applications.

    MISTLETOE on attachment configuration capture

    Need your advice is there any configuration that I miss... ??

     

    As long as you go to the STROKE centre should work in Flexconnect. You can check the AP mode under wireless > click on any access point.

    http://www.Cisco.com/c/en/us/support/docs/wireless/5500-Series-Wireless-...

  • WLC 5508 management interface

    Hi, I have a design requiring a WLC 5508 be connected to two separate swithces specific wireless. WLC 1 port is connected to the switch A trunk and WLC Port 2 is connected to the switch B. Each switch has its own local VLANS. When I connect the years 1130 towers they need find the interface of management initially then only use management. AP interfaces since there is only a single management interface, if the assignment of management interface on a VLAN that is configured on the switch then APs on spend a fine join but those switch B continue to ask for the management interface and the version debug capwap on WLC he says that this query Join were received on the bad ineterface...

    the only work around that was to do the routing between switch A and switch B for both VLAN residing APs... but for security reasons - customer would like to avoid this

    any help is appreciated...

    Unfortunately, the initial discovery must arrive in the management interface.  Once this has happened the AP expected the second AP manager who is on the subnet of comments, therefore, they are able to stand.  But if the AP is restarted, it would need to discover once again and would fail.

    What is the concern of customers to have all routable network mgmt AP?  guest users can not see anything there.

    IMO, let the AP able to connect to the subnet of mgmt, but then put an ACL L3 upward, to block the subnet of comments to achieve anything in the internal network.

  • Backup the IOS on a WLC 5508

    Hello

    Hope someone can help me, I have a Cisco 5508 WLC and wanted to backup the IOS.

    Is there an easy way to do it? or a Cisco restrict this function with the new IOS licensing model?

    Second question, with WLC 5508 IOS version 7.0.98 I see that there is no field recovery Image, is that correct?

    See you soon,.

    Ron

    I guess that you Q #1 has been addressed above.

    For your Q n ° 2 'the second question, with WLC 5508 IOS version 7.0.98 I see that there is no field recovery Image, is this correct?"

    Yes that is correct

    -->

    (w-5508-1) > show sysinfo

    Name of the manufacturer... Cisco Systems Inc..
    Product name... Cisco controller
    Version of the product... 7.0.98.0
    Bootloader Version... 1.0.1
    Retrieving Image Version field... N/A

    And it's a CSCth43373 bug

    5508 7.0 running shows the version of field recovery images by n/a

    Symptom:
    
5508 shows Field Recovery Image version as N/A.
    

    Conditions:
    

    Upgrade 5508 to version 7.0.98.0
    

    Workaround:
    

    None

    --

    You will have to wait for the new 7.0 code to appear on Cisco.com

    Be sure to mark the thread as solved if you feel that your issue has been addressed.

    Thank you

    Serge

  • WLC 5508 Active Directory / LDAP integration to authenticate

    Hello

    I am redundant deployment WLC 5508 with 4 VLANS and 4 SSID matches it, everything works fine, now I have to do the below, then please put your valuable comments and advice.

    1. I need all users authenticated with existing Active Directory/LDAP wireless

    2. I create accounts invited in my ad and go to the guests, so comments should only Internet access except the company's resources

    2. How can I get my VoIP VLAN for wireless phones. I want to only wireless phones to connect to VLANS voice. No internet access on VLan VoIP

    Concerning

    Dinesh

    Hello

    1. I need all users authenticated with existing Active Directory/LDAP wireless

    2. I create accounts invited in my ad and go to the guests, so comments should only Internet access except the company's resources

    YEARS 1 & 2 - the link below provides the example config and also the memorandum of understanding on the conditions depth, please go through the link atleast once...

    http://www.Cisco.com/en/us/products/ps6366/products_configuration_example09186a0080a03e09.shtml

    2. How can I get my VoIP VLAN for wireless phones. I want to only wireless phones to connect to VLANS voice. No internet access on VLan VoIP

    YEARS - you can configure the auth required for WLAN voice and then NAT this interface VLAN so that he won't get out of the internet!

    Let me know if that answers your question and please do not forget to rate traore useful messages!

    Concerning

    Surendra

  • Cisco ISE 1.2 & Cisco WLC 5508 v7.6

    Hi all

    We intend to upgrade our WLC to 7.6 to fix a bug with FlexConnect customer ACL but I just saw on the ISE Cisco compatibility table which it recommended only up to the WLC 5508 v7.5...

    Cisco told me to avoid 7.5 as it is in a State of defferred if anyone know or are running in a laboratory or production, ISE1.2 with a WLC v7.6 n 5508?

    I wish I knew rather questions of people know before hand than to have to go through a software update, and then restore.

    Thank you all

    Mario Rosa

    Definitely stay away from 7.5. I've done several deployments with the WLCs 7.6 running. The two main issues that I touched were:

    CSCue68065 - in this bug FlexConnect ACL does not work unless you have a regular (non FlexConnect) ACL created with exactly the same name

    CSCuo39416 - CWA does not not on FlexConnect APs. It would apply to you if you have older models APs

    I hope this helps!

    Thank you for evaluating useful messages!

  • Trouble getting a Cisco 2600 series AP to stay connected to WLC 5508

    Hello

    I recently loaded the independent our old APs upgrade to LWAPs.  We have a WLC 5508 to our Virtual Co - Lo and I use Flexconnect to accommodate local switch and dhcp on our sites.  I have updated more than 50 APs and joined them to the controller.  These include only the 1130AG and 1240AG models.  However they work perfectly and stay connected to the controller.  I'm having is with a new batch of 2600 series APs stay connected to the controller.  I tried to do research in what may cause disconnect it but have yet to find a solution.  I use DNS to resolve queries for CAPWAP & LWAPP APs to the controller on our EXTENSIVE network.  Read other messages I thought that this is perhaps a problem with packages to drop but have had our provider that manages Sonicwalls at both ends of the WAN confirm for me that there is no packet loss.  Here are the logs that I collected through the puttty of the WLC & AP.  Any help would be greatly appreciated.

    AP, I do the test on:

    NAME: "AP2600', DESCR: 'Cisco Aironet 2600 Series (IEEE 802.11n) Access Point.

    PID: AIR-CAP2602I-A-K9, VID: V01, SN: FTX1740J8V1

    WLC in question:

    Name of the manufacturer... Cisco Systems Inc..

    Product name... Cisco controller

    Version of the product... 7.3.112.0

    Bootloader Version... 1.0.1

    Retrieving Image Version field... 6.0.182.0

    Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27

    Build Type....................................... DATA + WPS

    System name... wificontroller

    Location of the system... Corp

    Contact System... Net engineer

    ObjectID of system... 1.3.6.1.4.1.9.1.1069

    Redundancy mode... People with disabilities

    IP Address....................................... 10.250.32.8

    Last Reset....................................... Software reset

    Time system... 190 days 3 hours 34 minutes 24 seconds

    Location of the time zone of the system... (GMT - 5:00) Eastern (USA and Canada)

    The country is set... USA - United States

    Operating environment... Utilities (0 to 40 ° C)

    Limits the internal temperature alarm... 0 to 65 ° C

    -Other - or ITU (q)

    ... Internal temperature 38 C

    Outdoor temperature... + 20 C

    Fan Status....................................... Ok

    State of 802. 11 b network... Activated

    State of 802. 11A network... Activated

    Number of wireless LANs... 14

    Number of Active Clients... 71

    Built-in MAC address... C8:9 C: D: 8 1: 52:E0

    Power supply 1... Currently, OK

    Power supply 2... Absent

    Maximum number of taken access points supported... 100

    Here is the result which leaves on concluded that the AP joins the WLC for a short period and then goes offline

    WT-4thFlr-AP3 #.

    * 15:42:04.419 Dec 14: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST

    ., 3)

    * 15:42:11.443 Dec 14: EVT-4-AVT %: write flash: / done event.capwap

    * 15:42:11.483 Dec 14: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode

    * 15:42:11.487 Dec 14: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION

    * 15:42:11.487 Dec 14: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.250.32.8:5246

    * 15:42:11.571 Dec 14: % FEDS-6-persons with DISABILITIES: Signature of IDS is removed and disabled.

    * 15:42:21.575 Dec 14: % 3-CAPWAP-ERRORLOG: MWAR selected ' wificontroller'(index 0).

    * 15:42:21.575 Dec 14: % 3-CAPWAP-ERRORLOG: go join a capwap controller

    * 15:42:12.000 Dec 14: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246

    * 15:42:14.303 Dec 14: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.250.32.8 peer_port: 5246

    * 15:42:14.303 Dec 14: % CAPWAP-5-SENDJOIN: send request to join 10.250.32.8

    * 15:42:15.127 Dec 14: "Promiscuous" from Ethernet mode

    * 15:42:15.535 Dec 14: LWAPP-4-CLIENTEVENTLOG %: OfficeExtend Localssid recorded Flash AP

    * 15:42:15.667 Dec 14: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1

    * 15:42:15.667 Dec 14: AC setting hop first MAC: 0017.c575.a23c

    * 15:42:15.855 Dec 14: % CAPWAP-5-JOINEDCONTROLLER: AP joined controller wificontroller

    * 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file

    * 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file

    * 15:42:15.911 Dec 14: LWAPP-4-CLIENTEVENTLOG %: map No. LS Flex to load ACL configuration file. To connect to the controller to get the configuration file

    * 15:42:15.915 Dec 14: LWAPP-4-CLIENTEVENTLOG %: no central Dhcp configuration file map to load. To connect to the controller to get the configuration file

    * 15:42:15.915 Dec 14: % LWAPP-3-CLIENTERRORLOG: connected mode

    * 15:42:23.639 Dec 14: FEDS-6-ACTIVATED %: Signature of IDS is loaded and enabled

    * 15:42:34.615 Dec 14: CLEANAIR-6-State: Slot 0 disabled

    * 15:42:34.615 Dec 14: CLEANAIR-6-State: Slot 1 disabled

    * 15:45:43.783 Dec 14: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST

    (. 11).

    * 15:45:43.787 Dec 14: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode

    * 15:45:43.787 Dec 14: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION

    * 15:45:43.787 Dec 14: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.250.32.8:5246

    * 15:45:43.867 Dec 14: % FEDS-6-persons with DISABILITIES: Signature of IDS is removed and disabled.

    * 15:45:53.867 Dec 14: % 3-CAPWAP-ERRORLOG: MWAR selected ' wificontroller'(index 0).

    * 15:45:53.867 Dec 14: % 3-CAPWAP-ERRORLOG: go join a capwap controller

    * 15:45:44.000 Dec 14: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.250.32.8 peer_port: 5246

    * 15:45:46.315 Dec 14: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.250.32.8 peer_port: 5246

    * 15:45:46.315 Dec 14: % CAPWAP-5-SENDJOIN: send request to join 10.250.32.8

    * 15:45:46.487 Dec 14: "Promiscuous" from Ethernet mode

    * 15:45:49.903 Dec 14: LWAPP-4-CLIENTEVENTLOG %: OfficeExtend Localssid recorded Flash AP

    * 15:45:50.031 Dec 14: ac_first_hop_mac - IP:10.1.2.250 Hop IP:10.1.2.250 IDB:BVI1

    * 15:45:50.031 Dec 14: AC setting hop first MAC: 0017.c575.a23c

    Here are the results of the client debugging capwap event about to access:

    WT-4thFlr-AP3 #debug capwap customer event

    Display debugging EVENT customer CAPWAP is on

    WT-4thFlr-AP3 #.

    * 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.

    * 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:54:58.335 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request

    * 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:54:58.343 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8

    * 15:55:08.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:55:08 UTC 14 December 2013

    * 15:55:25.579 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:55:25.587 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:55:25.587 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:55:25.587 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

    * 15:55:25.827 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:55:25.835 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:55:25.835 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:55:25.835 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

    * 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.

    * 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:55:55.835 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request

    * 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:55:55.843 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8

    * 15:55:56.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:55:56 UTC 14 December 2013

    * 15:56:25.735 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:56:25.743 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:56:25.743 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:56:25.743 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

    * 15:56:25.983 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:56:25.991 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:56:25.991 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:56:25.991 Dec 14: % CAPWAP-3-Journal of EVENTS: event Wtp 10.250.32.8 response

    * 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: Echo interval has expired.

    * 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: sending package to AC

    * 15:56:55.991 Dec 14: % 3-CAPWAP-EVENTLOG: echo sent to 10.250.32.8 request

    * 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: reset reTransmissionCnt to 0

    * 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: queue empty.

    * 15:56:55.999 Dec 14: % 3-CAPWAP-EVENTLOG: echo response from 10.250.32.8

    * 15:56:56.000 Dec 14: % 3-CAPWAP-EVENTLOG: setting the time at 15:56:56 UTC 14 December 2013

    Here are the results of debug capwap client package in detail:

    WT-4thFlr-AP3 #.

    * 14 Dec 15:59:01.823: <   start="" of="" capwap="" packet ="">>

    * 15:59:01.823 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 15:59:01.823 Dec 14: Type Msg: CAPWAP_ECHO_REQUEST

    * 15:59:01.823 Dec 14: Msg length: 0

    * 15:59:01.823 Dec 14: Msg SeqNum: 44

    * 14 Dec 15:59:01.823: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:01.831: <   start="" of="" capwap="" packet ="">>

    * 15:59:01.831 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:01.831 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:01.831 Dec 14: Type Msg: CAPWAP_ECHO_RESPONSE

    * 15:59:01.831 Dec 14: Msg length: 15

    * 15:59:01.831 Dec 14: Msg SeqNum: 44

    * 15:59:01.831 Dec 14:

    * 15:59:01.831 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 11

    * 15:59:01.831 Dec 14: the vendor identifier: 0 x 00409600

    * 15:59:01.831 Dec 14:

    * 15:59:01.831 Dec 14:

    IE: UNKNOWN IT IS ABOUT 151

    * 15:59:01.831 Dec 14: IE length: 5

    * 15:59:01.831 Dec 14: decode the routine unavailable, Hex Dump printing

    * 15:59:01.831 Dec 14:

    52 80 46 00 AC

    * 14 Dec 15:59:01.831: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:20.931: <   start="" of="" capwap="" packet ="">>

    * 15:59:20.931 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:20.931 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:20.931 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST

    * 15:59:20.931 Dec 14: Msg length: 93

    * 15:59:20.931 Dec 14: Msg SeqNum: 38

    * 15:59:20.931 Dec 14:

    * 15:59:20.931 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 89

    * 15:59:20.931 Dec 14: the vendor identifier: 0 x 00409600

    * 15:59:20.931 Dec 14:

    * 15:59:20.931 Dec 14:

    IE: RRM_NEIGHBOR_CTRL_PAYLOAD

    * 15:59:20.931 Dec 14: IE length: 83

    * 15:59:20.931 Dec 14: decode the routine unavailable, Hex Dump printing

    * 15:59:20.931 Dec 14:

    00 0 HAS FA 20 08 01 00 07 0A 20 08 03 00 01 FA F4

    01 00 00 3 B4 2ND 2ND 06 94 51 79 25 C7 B2 B4 E7

    22 FD BE F6 04 00 00 00 00 00 00 00 00 50 52 4F

    53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00

    00 00 00 00 00 00 00 00 00 00 00 00 00 01 06 0B

    01 01 01

    * 14 Dec 15:59:20.931: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:20.931: <   start="" of="" capwap="" packet ="">>

    * 15:59:20.931 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 15:59:20.931 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE

    * 15:59:20.931 Dec 14: Msg length: 8

    * 15:59:20.931 Dec 14: Msg SeqNum: 38

    * 15:59:20.931 Dec 14:

    * 15:59:20.931 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4

    * 15:59:20.931 Dec 14: result of Code: CAPWAP_SUCCESS

    * 14 Dec 15:59:20.931: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:21.139: <   start="" of="" capwap="" packet ="">>

    * 15:59:21.139 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:21.139 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:21.139 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST

    * 15:59:21.139 Dec 14: Msg length: 111

    * 15:59:21.139 Dec 14: Msg SeqNum: 39

    * 15:59:21.139 Dec 14:

    * 15:59:21.139 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 107

    * 15:59:21.139 Dec 14: the vendor identifier: 0 x 00409600

    * 15:59:21.139 Dec 14:

    * 15:59:21.139 Dec 14:

    IE: RRM_NEIGHBOR_CTRL_PAYLOAD

    * 15:59:21.139 Dec 14: IE length: 101

    * 15:59:21.139 Dec 14: decode the routine unavailable, Hex Dump printing

    * 15:59:21.143 Dec 14:

    01 0 TO FA 20 08 01 F4 00 07 0A 20 08 00 01 0C FA

    01 00 00 3 B4 2ND 2ND 06 94 51 79 25 C7 B2 B4 E7

    22 FD BE F6 04 00 00 00 00 00 00 00 00 50 52 4F

    53 2D 57 69 46 69 00 00 00 00 00 00 00 00 00 00

    00 00 00 00 00 00 00 00 00 00 00 00 00 24 28 2

    30 34 38 3 40 95 99 9 01 01 01 01 01 01 01 A1

    01 01 01 01 01

    * 14 Dec 15:59:21.143: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:21.143: <   start="" of="" capwap="" packet ="">>

    * 15:59:21.143 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 15:59:21.143 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE

    * 15:59:21.143 Dec 14: Msg length: 8

    * 15:59:21.143 Dec 14: Msg SeqNum: 39

    * 15:59:21.143 Dec 14:

    * 15:59:21.143 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4

    * 15:59:21.143 Dec 14: result of Code: CAPWAP_SUCCESS

    * 14 Dec 15:59:21.143: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:25.547: <   start="" of="" capwap="" packet ="">>

    * 15:59:25.547 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 15:59:25.547 Dec 14: Type Msg: CAPWAP_WTP_EVENT_REQUEST

    * 15:59:25.547 Dec 14: Msg length: 14

    * 15:59:25.547 Dec 14: Msg SeqNum: 45

    * 15:59:25.547 Dec 14:

    * 15:59:25.547 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 10

    * 15:59:25.547 Dec 14: the vendor identifier: 0 x 00409600

    * 15:59:25.547 Dec 14:

    * 15:59:25.547 Dec 14:

    IE: RRM_LOAD_DATA_PAYLOAD

    * 15:59:25.547 Dec 14: IE length: 4

    * 14 Dec 15:59:25.547: slot ccaLoad 0 rxLoad 0 txLoad 0 33

    * 14 Dec 15:59:25.547: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:25.555: <   start="" of="" capwap="" packet ="">>

    * 15:59:25.555 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:25.555 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:25.555 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE

    * 15:59:25.555 Dec 14: Msg length: 0

    * 15:59:25.555 Dec 14: Msg SeqNum: 45

    * 14 Dec 15:59:25.555: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:25.795: <   start="" of="" capwap="" packet ="">>

    * 15:59:25.795 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 15:59:25.795 Dec 14: Type Msg: CAPWAP_WTP_EVENT_REQUEST

    * 15:59:25.795 Dec 14: Msg length: 14

    * 15:59:25.795 Dec 14: Msg SeqNum: 46

    * 15:59:25.795 Dec 14:

    * 15:59:25.795 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 10

    * 15:59:25.795 Dec 14: the vendor identifier: 0 x 00409600

    * 15:59:25.795 Dec 14:

    * 15:59:25.795 Dec 14:

    IE: RRM_LOAD_DATA_PAYLOAD

    * 15:59:25.795 Dec 14: IE length: 4

    * 14 Dec 15:59:25.795: slot ccaLoad 1 rxLoad 0 txLoad 0 0

    * 14 Dec 15:59:25.795: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:25.803: <   start="" of="" capwap="" packet ="">>

    * 15:59:25.803 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:25.803 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:25.803 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE

    * 15:59:25.803 Dec 14: Msg length: 0

    * 15:59:25.803 Dec 14: Msg SeqNum: 46

    * 14 Dec 15:59:25.803: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:30.375: <   start="" of="" capwap="" packet ="">>

    * 15:59:30.375 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:30.375 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:30.375 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_REQUEST

    * 15:59:30.375 Dec 14: Msg length: 17

    * 15:59:30.375 Dec 14: Msg SeqNum: 40

    * 15:59:30.375 Dec 14:

    * 15:59:30.375 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 13

    * 15:59:30.375 Dec 14: the vendor identifier: 0 x 00409600

    SlotId: 0

    Mobile Mac Addr: BC:52:B7:E3:17:CB

    * 14 Dec 15:59:30.375: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:30.375: <   start="" of="" capwap="" packet ="">>

    * 15:59:30.375 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 15:59:30.375 Dec 14: Type Msg: CAPWAP_CONFIGURATION_UPDATE_RESPONSE

    * 15:59:30.379 Dec 14: Msg length: 8

    * 15:59:30.379 Dec 14: Msg SeqNum: 40

    * 15:59:30.379 Dec 14:

    * 15:59:30.379 Dec 14: Type: CAPWAP_MSGELE_RESULT_CODE, length 4

    * 15:59:30.379 Dec 14: result of Code: CAPWAP_SUCCESS

    * 14 Dec 15:59:30.379: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 15:59:30.387: <   start="" of="" capwap="" packet ="">>

    * 15:59:30.387 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 15:59:30.387 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 15:59:30.387 Dec 14: Type Msg: CAPWAP_WTP_EVENT_RESPONSE

    * 15:59:30.387 Dec 14: Msg length: 0

    * 15:59:30.387 Dec 14: Msg SeqNum: 47

    * 14 Dec 15:59:30.387: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 16:00:00.387: <   start="" of="" capwap="" packet ="">>

    * 16:00:00.387 Dec 14: control of CAPWAP mesg sent to 10.250.32.8, Port 5246

    * 16:00:00.387 Dec 14: Type Msg: CAPWAP_ECHO_REQUEST

    * 16:00:00.387 Dec 14: Msg length: 0

    * 16:00:00.387 Dec 14: Msg SeqNum: 48

    * 14 Dec 16:00:00.387: <  end="" of="" capwap="" packet ="">>

    * 14 Dec 16:00:00.395: <   start="" of="" capwap="" packet ="">>

    * 16:00:00.395 Dec 14: mesg 10.250.32.8 Recd, Port 5246 CAPWAP control

    * 16:00:00.395 Dec 14: HLEN 2, Radio ID 0, WBID 1

    * 16:00:00.395 Dec 14: Type Msg: CAPWAP_ECHO_RESPONSE

    * 16:00:00.395 Dec 14: Msg length: 15

    * 16:00:00.395 Dec 14: Msg SeqNum: 48

    * 16:00:00.395 Dec 14:

    * 16:00:00.395 Dec 14: Type: CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, length 11

    * 16:00:00.395 Dec 14: the vendor identifier: 0 x 00409600

    * 16:00:00.395 Dec 14:

    * 16:00:00.395 Dec 14:

    IE: UNKNOWN IT IS ABOUT 151

    * 16:00:00.395 Dec 14: IE length: 5

    * 16:00:00.395 Dec 14: decode the routine unavailable, Hex Dump printing

    * 16:00:00.395 Dec 14:

    52 80 81 00 AC

    * 14 Dec 16:00:00.395: <  end="" of="" capwap="" packet ="">>

    Try reducing the mtu on ap 2600.

  • Can't see all networks wifi on initial Setup

    There was a problem with my original Touchpad (it does), so I sent to HP and just received my refurbished model. However, when I start the initial setup and it asks me to connect to a Wifi network, none appear, even if my network and my neighbors are all visible & active.

    My network configuration has not changed since my original Touchpad, which connected very well, so I don't know why this one should give problems. Any thoughts? It is extremely frustrating that I can still use my new Touchpad!

    Following my previous post, I called HP, explained my problem and they sent me a replacement. The new (renovated) came in a few days later and it connected to Wifi without problem. I proceeded to the initial installation and have no problem with this new unit.

    So, for all those who still have a problem with an inability to see any Wifi access during the initial installation points, contact HP and explain your problem. If you are able to upgrade to 3.0.4 use WebOS Doctor, do this and confirm that your Mac address is all zeros. This seemed to be the point of triggering of a replacement for me.

    Good luck to all! I'm going to use CM7 .

  • WLC 5508 high availability

    Hello

    Today I have two WLC 5508 (with license for 100 AP each of them), on a single site.

    The WLC work availability (active-standby).

    However, we have a new scenario, with 02 sites: A and B (attachment).

    I would like to know if it is possible to work as follows:

    The WLC - A as the main controller of site A. WLC - B as a backup (BDC) of WLC.-a.

    The WLC - B that has the PDC site B. WLC - as a backup (BDC) to WLC - B.

    For example:

    If WLC - a falls, site access Points are managed by B WLC site - B and vice versa.

    Is this possible?

    How can I configure the new scenario? Don't forget, there is a site-to-site between Site A and Site b.

    Another point:

    If I add more than 50 APs on Site A. How does the license number?

    Should I buy a license for the two WLC?

    TKS,

    >....

    >.. .is it possible?

    No. , high availability in terms of controller is supposed to be what is said, the backup controller is not 'full' - stby and cannot play other roles.

    M.

  • WLC 5508 joined connected vs status

    Hello

    What is the difference between the status of 'Joint' and 'Connected' AP on the controller of Cisco 5508 wireless in HA configuration?

    I have two WLC 5508 in HA configuration. October 3 the controller switchovered with reason "Active controller failed" (attached file 1). I tried to understand why the controller has failed, but I did not find the reason.

    Now, there are a lot of AP (not all) in the 'connected' State, not 'Supported in status' (attached file 2).

    What is the meaning? and why in the details ' AP join stats ' (attachment 3 and 4) tha AP are well attached status? It's a licensing issue? I can solve this problem with a manual failover to main controller?

    Thank you for the help

    You have a license for 250 AP on your primary controller and the secondary is a SKU or has at least 50 AP license to act like a HA.

    As long as the main unit is available for the secondary unit (active) it will not perform the countdown. 90 days don't apply if the main unit is unavailable for more than 90 days in a row. If the secondary image (active) loses power and the principal is unavailable when it starts again, it will go into maintenance mode.

    Please rate helpful messages... :-)

  • SHIFT of Mode on Cisco WLC 5508

    Hello

    I have two WLC 5508 working in ACTIVE / standby. They are connected to my local network by linking to each WLC.

    I would like to implement the LAG Mode to have two WLC link but when I activate LAG Mode (Mode CONTROLLER/general/LAG at the next reboot active), I have this newspaper:

    "Error in the setting of the Mode of LAG. Please see the log file.

    I see nothing in the log file.

    The version of my WLC is 8.0.100.0

    Thank you

    First, you will need to disable HA if you want to enable the LAG.

    http://www.Cisco.com/c/en/us/TD/docs/wireless/controller/8-0/Configuration-Guide/b_cg80/b_cg80_chapter_010100001.html

    A time LAG configured on both controllers, you can then enable HA between two WLCs

    HTH

    Rasika

    Pls note all useful responses *.

  • Interface WLC 5508 AP-Manager

    Hi, I own a WLC 5508 and (probably), I do not understand the AP Manager interfaces. I have a laboratory with 2 x 1242AG and 1 x 1252AG connected to c2960. APs in vlan 10 (192.168.10.0/24, configured via DHCP), APs are connected to interface 'switchport access mode. C2960 is connected via a trunk to c4506 and WLC is plugged into article gi1/3 and article gi1/4 (both through twingig). The two ports are configured as 'switchport mode trunk ". WLC management interface is IDE oucederomsurlesecondport WLC 8 (linked to article gi1/4), and AP-Manager is on port 1 (connected to article gi1/3) WLC. WLC management interface has 'Management dynamic AP' set to off, and AP-Manager defined activated. The two are interfaces to management and AP-Manager tag, vlan id 12 and 13 (subnets 192.168.12.0/24, 192.168.13.0/24) respectively. APs receive their IP through DHCP configuration (server located in vlan 20, 192.168.20.0, in use ip helper-address) and try to discover DNS resolution WLC (CISCO-CAPWAP - CONTROLLER.some.domain resolves to AP-Manager IP correctly). But AP has the status "not connected" in monitor/statistics/AP join APs do not join to the controller, said WLC "Discovery request Ignoring received on the management interface".

    But if I put management interface as "Dynamic AP activated" and change the DNS to resolve CISCO-CAPWAP... it's IP everything works well - AP is associated with the time. Please help, how to reach the KNEES a AP-Manager interface? Sign up for the Manager of WLC is simple, but my design requires at least 2 interfaces AP Manager.

    If you have a 5508, why you have the AP Manager?

  • Cisco ISE 2.0 and WLC 5508 with 7.6.130.0

    I have looked on the release notes and compatibility n for ISE 2.0 and have not seen the answer to that. For the WLC 5508, the minimum AirOS is 7.0.116.0 but he limited the AAA authentication and support for comments. The recommended version of AirOS is 8.0.121.0.

    http://www.Cisco.com/c/en/us/TD/docs/security/ISE/2-0/compatibility/ISE _...

    What airos 7.6.130.0? I know that AirOS release works with 1.3 and 1.4, even if they show the same support for version 2.0. I'm just afraid that something may have changed with 2.0. I am concerned only about the AAA authentication and guest access. No BYOD, posture or MDM is necessary.

    No change. Works well.

  • WLC 5508 internal DHCP server issues

    Hello

    I'm hoping to get your comments around the issues of dhcp, I faced with two centrally switched Wireless LAN. I have attempted to explain the installation and the problems below and would be grateful if anyone can suggest a solution for the problems I am facing:

    The configuration is the following:

    -J' have a WLC 5508, which has been configured with 4 SSID, of which 2 are the Central authentication and commissioning.
    -J' have a LWAP connected to the WLC in HREAP mode.
    -WLC is configured as a DHCP server for clients that connect to the SSID "Guest." For the rest, I'm on external dhcp server.
    -Only one scope of comments Interface is configured on the WLC.

    Problems:

    1. as far as I know, to WLC serve internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to 'Internet' SSID are

    Unable to get an external dhcp server ip address, if the proxy dhcp is enabled on the WLC. If I disable the proxy, everything works fine.

    2 DHCP does not release the ip addresses assigned to clients, even after that that they are connected.

    3. If a machine that has previously been connected to "Guest" SSID connects to the 'Internet' SSID, he asks the same ip address, he was charged by the WLC assigned under "Guest", it gets the tag with the Vlan configured on the management interface.

    The controller output *.

    (Cisco Controller) > show sysinfo

    Name of the manufacturer... Cisco Systems Inc..
    Product name... Cisco controller
    Version of the product... 7.0.116.0
    Bootloader Version... 1.0.1
    Retrieving Image Version field... 6.0.182.0
    Firmware version... Console USB 1.3, 1.6 Env FPGA, 1.27
    Build Type....................................... DATA + WPS, LDPE

    (Cisco Controller) > show interface summary

    Name interface Vlan Id IP port address Type Ap Mgr. Gu

    EST
    -------------------------------- ---- -------- --------------- ------- ------ --
    1 301 10.255.255.30 dynamic guest no no
    Management 1 100 172.17.1.30 static yes no

    service-port s/o s/o 192.168.0.1 static no no
    n/a n/a 10.0.0.1 no nonstatic virtual

    (Cisco Controller) > show wlan summary

    Number of wireless LANs... 4

    Profile WIFI WLAN ID name / name of the SSID status Interface
    -------  -------------------------------------  --------  --------------------
    1 active LAN management
    2 active Internet management
    3 active active management management
    4 comments comments enabled

    (Cisco Controller) > show dhcp detailed comments

    Scope: comments

    Enabled.......................................... Yes
    Lease Time....................................... 86400 (1 day)
    Pool Start....................................... 10.255.255.31
    Pool End......................................... 10.255.255.254
    Network.......................................... 10.255.255.0
    Netmask.......................................... 255.255.255.0
    Default routers... 10.255.255.1 0.0.0.0 0.0.0.0
    DNS Domain.......................................
    DNS.............................................. 8.8.8.8 8.8.4.4 0.0.0.0
    NetBIOS name servers... 0.0.0.0 0.0.0.0 0.0.0.0

    (Cisco Controller) > show detailed interface management

    ... Management interface
    MAC address... e8:b7:48:9 b: 84:20
    IP Address....................................... 172.17.1.30
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 172.17.1.1
    State IP NAT outside... People with disabilities
    External IP NAT... 0.0.0.0
    VLAN............................................. 100
    Quarantine-vlan... 0
    Active physical Port... 1
    The primary physical Port... 1
    Port of physical backup... Not configured
    Primary DHCP server... 172.30.50.1
    Secondary DHCP server... Not configured
    Option DHCP 82... People with disabilities
    ACL.............................................. Not configured
    AP Manager....................................... Yes
    Comments interface... NO.
    L2 multicast... Activated

    (Cisco Controller) > show detailed comments from interface

    Interface name... Comments
    MAC address... e8:b7:48:9 b: 84:24
    IP Address....................................... 10.255.255.30
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 10.255.255.1
    State IP NAT outside... People with disabilities
    External IP NAT... 0.0.0.0
    VLAN............................................. 301
    Quarantine-vlan... 0
    Active physical Port... 1
    The primary physical Port... 1
    Port of physical backup... Not configured
    Primary DHCP server... Not configured
    Secondary DHCP server... Not configured
    Option DHCP 82... People with disabilities
    ACL.............................................. Not configured
    AP Manager....................................... NO.
    Comments interface... NO.
    L2 multicast... Activated

    (Cisco Controller) > show dhcp leases

    IP MAC remaining rental period
    00:21: 6a: 9 c: 03:04 10.255.255.46 23 hours, 52 minutes, 42 seconds< lease="" remains="" even="" when="" the="" client="" is="">

    Example of customer connected to the Vlan right with an ip address from the incorrect interface. *************

    (Cisco Controller) > show customer detail 00:21: 6a: 9 c: 03:04
    MAC address of the client... 00:21: 6a: 9 c: 03:04
    User name of the client... N/A
    AP MAC address... a0:cf:5 b: 00:49:c0
    AP Name.......................................... mel
    Status of the client... Associates
    Customer of the NAC OOB State... Access
    Wireless LAN Id... 2<   'internet'="">
    BSSID... a0:cf:5 b: 00:49: this
    Connected to... dry 319
    Channel.......................................... 36
    IP Address....................................... 10.255.255.46< ip="" address="" assigned="" from="" the="" 'guest'="" interface="" or="" dhcp="" scope="" on="" the="">
    Association ID... 1
    Authentication algorithm... Open System
    Reason code... 1
    Status code... 0
    Session timeout... 1800
    Client CCX version... 4
    Version of E2E customer... 1
    QoS Level........................................ Silver
    Beacon priority P 802,1... disabled
    Support WMM... Activated
    Power Save....................................... OFF
    State of mobility... Local
    County of movement mobility... 0
    Complete security policy... Yes
    State Policy Manager... RUN
    Policy Manager rule created... Yes
    ACL name... no
    Status to apply ACL... Not available
    Type of strategy... N/A
    Encryption Cipher... None
    Protection management framework... NO.
    EAP Type......................................... Unknown
    Data HARVEST-H switching... Central
    H - HARVEST authentication... Central
    Management of the interface...
    VLAN............................................. 100< right="">
    Quarantine VLAN... 0
    Access VIRTUAL LAN... 100

    Well it's good news. At least you have to operate.

    Thank you

    Scott Fella

    Sent from my iPhone

Maybe you are looking for

  • I accidentally updated to iOS 9.3.2 is anyway I can go back to iOS 8.4.1?

    I upgraded my iPod 5th generation, and I regret it. It's horrible! The different functions it slows down and make it really bug. I have even reduced the animations, extinct iCloud, and it still manages trolling. Is there anyway that I can get it back

  • Read my version of Firefox Add - ons incorrectly

    I just upgraded to Version 7 of Firefox 3.0.11. I wanted to add some add-ons, but the Add-ons page won't let me download any of the new stuff because it says that I'm still in Version 3.0.11. To help title > tab on Firefox, it says that I am, indeed,

  • A form of Google with http POST VI

    Dear LabVIEW forum, I'm filling out a very simple form of Google consisting of 4 text fields named AI0 AI1, AI2 AI3. I use the http POST provided by LabVIEW VI: When I run this, a new row is added to the answer sheet, but values do not appear, with t

  • 3 beeps on Lenovo 3000 N200 starts

    Bought a lenovo 3000 N200 on eBay that was dead, looked as if it was probably a failure of the motherboard to nothing lit up.  Got a 2nd motherboard user with the same number of eBay and mounted FRU 41R7886, now when I turn on the laptop the drive li

  • WeBWorK API operation.

    Filming services works not in webworks, anyone know if it's on the roadmap, to make it compatible?