WLC existing 8510, switch mode with additional 8510-HA new HA SSO

Similar Questions

• UCS in switch mode

  Hello

  It is supported to connect 3 third-party servers to the fabric of interconnections in a UCS in the switching mode?

  Is the switch in UCS mode fully supported (even if not preferred)?

  Thank you

  Even if its switching mode "called" she should not be considered a switch.  It is an interconnection fabric and intended to connect only the servers Cisco and storage 3rd party devices.   You must understand if we said that it is 'ok' to fix any ethernet device it would open valves to a lot of problems of support for the system.

  I hope that if you can afford a UCS you can allow you an additional switch to connect your 3rd - party servers or just replace with UCS servers all together ;-)

  Robert

• 2910al - 48G Switch: problem with the VLAN

  Hi all,

  I write a new message because I don't know what is happening on my SW series 2910al - 48G and v1910 - 48G.

  I put on the main core SW VLAN 610 and I put to this VLAN IP addreess 100.110.10.1 24-bit etc and it worked fine until yesterday. I change only PLEASE and I enebale STP - loop protect for ports in the range 1-52. (now I rolback this settings as was before)

  

  STP configuration

  

  Now, every PC that has for a long time what IP range 100.110.10.1 24-bit works fine, but new PC have problem with to get the new IP address. I tested it add a static and same address does not work.

  Introduced in second v1910 SW - 48 G VLAN as below

  I connect this flexible switch this \port SW 2910 - G 48, 46 (Vlan 610 tag) <>- at v1910-48G\ port 50 SW (Vlan 610 tahgged) other ports on this switch I put not marked.

  Configuration file for sw v1910 - 48G looks to below:

  #
  activate default domain system
  #
  LLDP enable

  #
  domain system
  disable the access limit
  Active state
  Disable Idle-cut
  self-service-url disable

  #
  rstp STP mode
  enable STP
  #
  NULL0 interface
  #
  GigabitEthernet1/0/1 interface
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/2
  access port vlan 610
  #
  interface GigabitEthernet1/0/3
  access port vlan 610
  #
  interface GigabitEthernet1/0/4
  access port vlan 610
  #
  interface GigabitEthernet1/0/5
  access port vlan 610
  #
  interface GigabitEthernet1/0/6
  access port vlan 610
  #
  interface GigabitEthernet1/0/7
  access port vlan 610
  #
  interface GigabitEthernet1/0/8
  access port vlan 610
  #
  interface GigabitEthernet1/0/9
  access port vlan 610
  #
  interface GigabitEthernet1/0/10
  access port vlan 610
  #

  #
  interface GigabitEthernet1/0/49
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/50
  hybrid type port link
  port hybrid vlan tagged 610 620
  port hybrid vlan 1 10 untagged
  #
  interface GigabitEthernet1/0/51
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1
  #
  interface GigabitEthernet1/0/52
  hybrid type port link
  port hybrid vlan tagged 610 620
  untagged port hybrid vlan 1

  etc...

  Could you help me when I made a mistake?

  THX

  The problem was that solve this problem.

  I have blocked all ports. It was a problem. I change several settings and everything works well.

• Yoga 2 Pro: randomly switches modes even when closed and the peripheral use

  I recently bought a Yoga 2 Pro, and I love it, except for an extremely annoying issue.

  It toggles randomly modes on me without moving the screen. I have not been able to develop a model for switching, it seems to be completely random. This morning I use this connected to a monitor of periperal via HDMI with the lid closed, and it was fine for about an hour and then started switching of the modes - tablet, back to laptop, the marquee, stand up, back to laptop, for tent...

  One of the benefits of its use with peripheral keyboard are the other modes don't disable the keyboard, but it is to randomly change the orientation of the screen. When I used it on its own without the devices, I can be typing away in the configuration of the laptop and all of a sudden it switches modes and the laptop is disabled.

  Sometimes, it is very well for hours and then will be randomly 10 times in 30 seconds.

  I know that I can turn on the rotation lock, but I just that it works correctly. He has been behaving in this way since the first night I bought it.

  All my windows updates are current and I reinstalled the drivers of transition of Yoga.

  Help, please. I need my computer for United work and cannot have a malfunction all the time and also cannot afford to lose if, during a period of time to have it fixed.

  I think it's finally fixed, but he forced me to return the unit for repair.

  Repair Center took two will solve the problem, but the ultimate fix seems to have required the replacement of the LCD: I guess there is some kind of sensor attached to the LCD unit. They replaced the motherboard and reconfigured the unit before replacing the LCD screen, so I can't be certain that he was not also a problem with the motherboard.

  So I guess I would recommend all those who encounter this issue gets their unit in a Service Center for repair before the warranty runs out. The warranty repair process wasn't as smooth as I would have liked, but ultimately it looks like my machine works fine now, and I don't think that any amount of waiting for updates of pilot would have set it.

• How to get out the mode safe mode with msconfig.

  I'm working on my computer and need to start in safe mode. I ran the msconfig and reboot the laptop. I get to the login screen, but when I get my username and password it tells me that the user name and password is not correct. How to get out the mode safe mode with msconfig.

  When you run msconfig to get set to Safe Mode, you just activate/check the option/SafeBoot at startup. INI tab or did you do something else?

  There is some malware that if you use the/SafeBoot option, you will not be able to use your system again until you remove the switch/SafeBoot the boot.ini for you can boot normally.

  Maybe it's not your exact problem, but I will never suggest to anyone to use the option / SafeBoot never again - too risky when troubleshooting since you can always start new or will never connect again until you remove the switch/SafeBoot.

  Anywho, if that's what you have done, you can start in the XP Recovery Console and then either make a new boot.ini file containing the switch/SafeBoot or simply rename the boot.ini file, you have something like boot.ini.old if you don't have a boot.ini file (I know it seems like a weird idea).

  In a single partition configuration, XP is not even a file boot.ini to boot.  XP will complain if there is no boot.ini file, but will always start very well without one (non-believers - try it!).

  After you get booted up and logged in, you can rename boot.ini.old in boot.ini and run msconfig to remove the option/SafeBoot, and never use it again.

• E2000 in Switch Mode

  My home network is configured with a box from Netgear 8 port that the server DHCP and an E2000 to wireless access (and some wired so ports) to set the mode.

  Since the E2000 is no longer a DHCP server, it loses its IP 192.168.1.1 address and appears to be assigned as 192.168.0.8.  When I try to access the E2000 this new address using the browser based utility, the expected login screen appears, but it doesn't seem to be a password that works.  According to the instructions of the key WAP is supposed to be the password and it worked before when the E2000 has been implemented as a router.

  I think that I do not understand something here.  Comments?  If I need/want to change the settings am I forced to reset the E2000 and start every time if I use switch mode?

  Nevermind... According to the best information I can find, a switch is not displayed as a separate device in a table of DHCP addresses

• Direct Login mode with CAT OS using Ganymede +.

  Hello

  I use RADIUS for authentication on IOS, and switches CAT OS. When I connect the IOS ones, coming directly to the activation of the mode.

  When I connect to the switch CAT OS with the same user, I get only in exec mode. So, I have to enter the mode activate manually with the "Ganymede user password" as "enable password.

  My wish is to connect directly to the activation of the mode with switches CAT!

  Thanks in advance...

  IOS config:

  -----------

  AAA new-model

  RADIUS-server key xxxx

  RADIUS-server host a.b.c.d

  AAA of default login authentication group Ganymede + activate

  AAA authorization exec default group Ganymede + authenticated if

  AAA authorization commands 15 default group Ganymede + authenticated if

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  line vty 0 4

  by default the authentication of connection

  Config from cat BONE:

  --------------

  define a.b.c.d primary RADIUS server

  Ganymede Set tent 5

  Disable directedrequest Set Ganymede

  Set Ganymede key xxxxxx

  the value of timeout Ganymede 5

  set authentication login Ganymede turn off the console

  set authentication login Ganymede activate telnet primary

  set authentication enable Ganymede turn off the console

  set authentication enable Ganymede activate telnet primary

  set the local connection authentication enable console

  set the local connection authentication enable telnet

  console game of authentication enable local enable

  set the local enable authentication enable telnet

  @rtogonon

  It is a command of IOS!

  Michael

• Compatibility of switches access with ISE

  Hi all

  I need some advice on models of switches buy to support almost all of the features that the ISE offeres... Mainly...

  MAB, 802. 1 x, Web Auth, CoA, dACL, SGA...

  Now, I've been reviewing the Cisco 2960 switches and sheets advise that they support some features, but then when I look at the compatibility of the access network Cisco ISE device list that was updated in December 2013... When you look under Cisco 2960, he advises that they support only 802.1 x, & MAB?

  I'm planning for the future deployment of ISE features to access switches in our network, but need to ensure that A) existing switches support these features and B) new switches that we buy will support these features.

  Is there a more accurate document available, or someone has had experience with the current Cisco 2960 switches and how they work well with the ISE?

  Thank you

  Mario

  Take a look at this link instead:

  http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-2/compatibility/ise_sdt.html

  DACL, WebAuth (both local and Central) is certainly supported. SGA/SGT isn't right...

  Thanks for the note!

• Windows cannot find network mode safe mode with networking cards?

  Hello.

  When I try to access a Safe Mode with network I can not connect to the Internet, because windows can not find any network adapters. But it is perfectly fine in Normal Mode. I tried to uninstall and reinstall the NICs without success. What can I do? I need help badly.

  Or is it simply not not in safe mode with network and will rather /normal/Mode safe.

  BTW, my laptop is model Vaio series S 2011.

  Thank you very much.

  Hello

  Thank you for writing to Microsoft Communities. From your problem description, I understand that you can not connect to Internet in safe mode with network. Please correct me that I misunderstood.

  Please provide us with additional information by answering a few questions below, this will help us better solutions to the problems.

  -Why are you trying to connect to Internet in safe mode with networking?

  -Do you get any error code or error message?

  I doubt that the choices you make in the options of safe mode takes you to the safe mode and the insecure with networking mode.

  Please do the following and check if you are able to boot into safe mode with network.

  a. restart the computer and press the F8 key during reboot, until you get the Advanced startup options.

  b. in the boot advanced options, use the keyboard to select safe mode with network and press ENTER.

  c. This will start the computer in safe mode with network. Once the computer has been started, check if you are able to connect to the Internet.

  For reference:

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Please try these steps and if the problem persists, please tell us so that we can help you.

• need to run windows in safe mode with network to have browserws working properly. using IE and Firefox. Website of punch comes in properly next tab sites just wai

  need to run windows in safe mode with network to have browserws working properly. using IE and Firefox. Web site fisting comes in following correctly sites just waiting for the website tab help

  If it works in Windows safe mode, then you have a problem with other software, maybe a security software or a system driver that runs on your computer.

  It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls
  • https://support.Mozilla.org/KB/fix-problems-connecting-websites-after-updating

• I see not that everything written on the firefox page. But when open secure mod (with SHIFT because there is no written) firefox run normally.

  I see not that everything written on the firefox page. But when open secure mod (with SHIFT because there is no written) firefox run normally.

  If you have tried safe mode and the problem disappeared, this means that one of your modules are the origin of the problem are seen.

• Typing becomes very slow in Firefox 3.6.11 in Mode safe mode with all extensions and plugins disabled.

  When I first start Firefox, all right. And everything is fine as long as I type in the text boxes on any web page. I can type in the address bar or search throughout the day with no problems.

  But, for example, just by typing in the edit box to ask this question on this site will result in the problem after I typed more say 150 characters. After this strike ANYWHERE in Firefox will be very slow, even the address bar or the search bar. It doesn't seem to matter what site use to type in the text. Cause the problem to occur after typing in enough strikes.

  Navigation & mouse clicking remains fast - it is only typing seems to be affected. In order to recover, I have to restart Firefox.

  If I look at the use of the UC Firefox.exe in Process Explorer, I see that once the problem occurs, the CPU usage starts whenever I type a key fortification. Indeed Firefox maxes one of my two hearts so the cpu is at 50%! He goes down to 0% again once I stop typing.

  As mentioned in the subject, it is in Mode safe mode with all extensions & plugins disabled. I'm running on Windows XP SP3 with an old AMD Athlon 64 X 2 Dual Core Processor 3800 + (1.81 Ghz) with 2.00 GB of RAM.

  I think it started to happen with Firefox 3.6 significantly (it's amazing how much time I can navigate without having to type), but it sometimes occurred with previous versions. Now he is annoyingly repeatable.

  I have to use '-no - Pei ForTyping distance "to start a separate session of Firefox that I use just to type in the text boxes, so I can restart at will. I also compose messages in an external editor and simply paste in Firefox to avoid typing as much as possible.

  This may be a problem with session restore. Firefox stores session data every 10 seconds to make it possible to restore a session crashed.

  It may be a problem with the sessionstore.js file in the profile folder

  Delete the sessionstore.js and sessionstore.bak and all files files sessionstore-# .js with a number in the left part of the name as sessionstore - 1.js.

  See http://kb.mozillazine.org/Session_Restore

• WiFi MiniPCI card only works in "Safe Mode with network.

  AR5001Xplus MiniPCI card only works in "Safe Mode with network" (windowsXP-Home-SP2 and all updates recent).
  In 'normal' mode, it freezes my laptop after a few seconds.

  Hello

  Why you don t give us more information about your problem? We don't know what unit you have? Is the original part of card or you have built at least?

  At the moment I can just recommend you to reinstall the unit with recovery media. If the problem persists, try to install the card separately with the right driver. Otherwise, you must change the WiFi card or test it with the other.

  Give us more information.

• How can I switch phones with a member of the family without losing the data on a phone?

  How can I switch phones with a member of the family without losing the data on a phone?

  jkatts wrote:

  How can I switch phones with a member of the family without losing the data on a phone?

  Make a backup of each phone to iTunes or iCloud (do not forget to use your Apple ID or personal computer), then do whatever your carrier wants do you to change numbers if that's your intention, then restore these backups on the device of the "other."

• A module C - DAQ exists which will interface with standard RV - C?

  Module C - DAQ exists that if interface with standard RV - C (vehicles recreational CAN)? RV - C seems to be a variant of J1939 according to Wikipedia.

  I would use 9861 OR or NI 9862. I'm new on CAN protocol and evaluate some assistance.

  I've never used RV - can, but according to Wikipedia, the rate is 250Kbaud, so you'll want high speed CAN peripheral, 9862, you can set baud rate on init of the material.  After installing XNet and cDAQ software, you have a max bus monitor and several examples in the example Finder to read and write raw images.  After that, you'll want to read on the standard to understand how to format and analyze the data.

  Also if you have any questions, you can post on the Sub-forum Auto , they can probably answer more specific questions.