WPC54G V2 - monitor WLAN

Similar Questions

• WUSB54GC - WLAN monitor does not not on Windows 2000 SP4 computer laptop

  I have a WUSB54GC v3 and I tried to install the drivers and the WIFI monitor on a Gateway Solo 5300 laptop running Windows 2000 SP4.  When I put the disc, the installation automatically started, but stopped after a few seconds with a pop message saying, "this version of windows is not supported" (or something similar to that).  I read in this forum and learned how to manually install the driver from the disk I did.  I checked the device using troubleshooting in Device Manager and shows the driver to be installed correctly and the device works correctly.

  My big problem is that the monitor WLAN (the little green square in the bottom right of the screen) will not illuminate.  There are no available wireless networks and the monitor does not respond to the "Refresh" or anything else.  It seems to be "dead".  How can I get the monitor to work?

  Thank you!

  Mike

  WUSB54GC is not compatible with Window2000... So either you can upgrade your operating system to Windows XP, or you can go for different cards as WUSB54G.

• WLAN monitor says adapter not installed - WMP11, but it works very well

  I installed a WMP11 wireless adapter in my desktop Compaq XP family and everything seems to work very well.  I can access the Internet and also home the other computer on my LAN.  But the WLAN monitor stresses the fact that the card is not installed.  For a few hours last night, it recognizes the card, but today it isn't.  I re - run Setup without result.  I have not reinstalled the drivers and card because things work correctly.  Any suggestions on what's wrong with the WLAN monitor?

  In addition, the device manager says that the card is installed and working properly.  Only WLAN Monitor to be confounded.  I fear that this means that something is wrong - and I find both less convenient.

  If the WIFI monitor does not work properly, you must use the Windows wireless to connect to your wireless network...

  (1) uninstall the adapter in your programs menu.

  (2) Insert the installation CD in the CD-ROM drive and wait for the Welcome screen, on the Welcome screen, click on Exit and restart the computer...

  (3) when the Hardware Update Wizard window appears, click on install the software automatically (recommended) and then click Next.

  NOTE: The hardware installation screen may appear indicating that the adapter has failed the Windows Logo test.

  (4) ignore the window and click on continue to continue the installation because the adapter has been tested and it works with Windows XP...

  (5) when Windows has finished installing the driver, click on Finish.Goto Control Panel and double-click on network connections...

  (6) right click on wireless network connection, and then select view available wireless networks "-If you see your network wireless in the list, the highlight by clicking 'single' on it now, click on the 'Connect' button below-if your wireless network is secured, it asks you to provide the network key - provide the wireless network key and confirm again in the confirmation box and click 'Connect'." It should work...

• Satellite L350 - 20 d is able to connect a 2nd monitor with WLAN?

  Hello

  If I understand correctly searches there ist a function called 'widi' which goes hand in hand with Intel chips.

  On the Intel West website a widget ready for download widi. As I was using XP so far, I understand, widi will work with win 7 Lea.

  Didn t update my windows because I use quite a few programms pretty expensive software update.

  My question, before I go through the process of update: is the chip of the Satellite L 350 - 20 d working with widi? Cause if not, I´ll rather try instead a wlan card.

  It s more work that I thougt to get my TV with my laptop as a server...

  Mouma

  As far as I know, you can only use a single display device / with Intel WiDi at the same time.

  I recommend the Intel page for more information about the Intel WiDi feature:
  http://www.Intel.com/content/www/us/en/architecture-and-technology/Intel-wireless-display.html

  Intel® Wireless Display requires a compatible laptop, TV adapter and a TV with HDMI or composite A / V input.

  System requirements for the Intel® Wireless Display_

  * CPU: * ONE of the following values:
  Processor Intel® Core i7: 640M; 660LM; 640LM; 620LM; 620 M; 610E; 690UM; 680UM; 660UM; 640UM; 620UM; 660UE; 2710QE; 2820QM; 2720QM; 2635QM; 2630QM; 2657M; 2649M; 2629M; 2620M; 2617M; 2540M; 2520M; 2510E; 2640LM; 2620LM; 2630UM; 2610UM; 2530UM; 2920XM
  Processor Intel® Core i5: 580M. 560 M; 540 M; 520 M; 480 M; 460 M; 450 M; 430 M; 580UM; 560UM; 540UM; 520UM; 470UM; 430UM; 2540M; 2520M; 2410M; 2537M; 2430M; 2435M, 2450M; 2467M
  Processor Intel® Core i3: 390M. 380 M; 370 M; 350 M; 330 M; 330TH; 2310M

  * Chart: * Intel® HD graphics card

  * Wireless network card: * ONE of the following values:
  Intel® Centrino® Wireless-N 1000, 1030, 2200 or 2230
  Intel® Centrino® Wireless - N 2200 for desktop
  Intel® Centrino® Advanced-N 6200, 6205, 6230 and 6235
  Intel® Centrino® Advanced - N 6205 for desktop
  Intel® Centrino® Wireless-N + WiMAX 6150
  Intel® Centrino® Advanced-N + WiMAX 6250
  Intel® Centrino® Ultimate-N 6300

  * Software: *.
  Intel® My WiFi Technology (Intel® MWT) 2 and Intel® Wireless name1 must be pre installed and activated.

  * OPERATING SYSTEM: *.
  Windows 7 64 - bit *, Home Premium, professional or full edition
  Windows 7 32 - bit *, Home Premium, ultimate, professional or Basic
  Windows * 8 32-bit and 64-bit editions

• Satellite Pro C850 - WLAN call default after installing Win 7

  Hello

  I own a C850-1 gr (PSCBXE), which comes with Win8.
  I bought Win 7 32 bit Home Premium and reinstalled from scratch.
  Later I installed the drivers from toshiba support page in the following order:

  Chipset SW installation utility
  Intel Management Engine Interface
  Display driver
  Intel Rapid Storage Technology driver
  Realtek Audio Driver
  ATI HDMI Audio Driver
  HD SRS Premium Sound Technology
  Synaptics Touch Pad Driver
  Realtek LAN Driver
  Realtek driver LAN wireless
  Intel Wireless Display
  Filter driver package Realtek Bluetooth
  Bluetooth monitor
  Intel USB3.0 driver
  Realtek card reader
  TOSHIBA Value Added Package
  Sleep TOSHIBA utility
  TOSHIBA resolution + plug-in for Windows Media Player
  TOSHIBA Media Controller
  TOSHIBA Media Controller plugin
  TOSHIBA Network Device ID registry tool
  TOSHIBA Web Camera Application
  PatchFiles PCIIDEREG - 1.2
  PatchFiles

  When installation is complete, WLAN fails after reboot, alternating.
  This means:

  * First boot: WIFI OK *.
  * Second startup: WLAN failed *.
  * Third start-up (= first boot): WIFI OK *.
  * Fourth Starter (= second boot): WLAN failed *.
  *...*
  * and Yes guess

  Lack of resources, the WLAN icon is displayed for a few seconds, then "no network" icon.

  Any help is greatly appreciated.

  Hello

  Your order of installation of drivers contains the Intel WLan driver.
  But the laptop Satellite Pro C850-1 GR was equipped with the Realtek RTL8723AE WLan/BT combo card.

  I think that you need to uninstall the Realtek WLan driver and WLan Intel driver.
  In addition, you must pay attention to the functionality of BT.

  The card is compatible with the BT and you need to install the driver Package Realtek Bluetooth filter before installing the battery Toshiba BT.

  In addition, do not forget that this WLan adapter is enabled by using the FN + F12 (or just the F12)

  Finally and above all do not forget WHAT BIOS the dafault value

• Satellite L670 - 134 PSK3EE: no clean button WLan FN + F8 after Win7 install

  Hello

  I have reinstalled a 'clean' Windows 7 Home Premium 64-bit and installed all the drivers that I need (I think: P)

  Value Added Package
  Turbo Boost technology
  Wireless Lan driver
  Bluetooth monitor
  Card reader controller
  Chip Set Utility
  Display driver
  Flash Cards Support utility
  Intel Management Engine Interface
  Touch Pad Driver
  LAN driver
  Audio driver

  If all the works of FN Key´s but no WiFi on / off

  I hope someone can help me with my problem :) and sorry for my bad English

  Hi mate

  So you mean all other FN keys work correctly, but only the FN + F8 key combination does not work as it should?

  This means that you can not activate WLan I would recommend setting the BIOS to the default settings and reinstall the WLan driver again
  The fact is that if the WLan driver would not work or if the WLan card is not installed properly, then the FN + F8 key combination does not work too.

  Update the driver WLan using this page:
  http://APS2.toshiba-tro.de/WLAN/

  Good luck

• My Satellite C850D has problem in WLAN signal

  I had a problem with the connection to the internet wireless in recent weeks.

  I sometimes luck and he would take our router at home, but more often there otherwise the computer monitor with the x bit red in it at the bottom of my screen.

  He could not pick up any network at all. If I help it, he just repeatedly told me that I needed to install an ethernet cable, but I want to connect wireless.

  I Googled it and saw a lot of things about the drivers and I assumed it was my problem. I uninstalled my two wireless drivers and then scanned a new hardware, like the many tutorials will tell you, but nothing happened.

  I went to the Toshiba site and seemed to wireless drivers so I downloaded the Realtek one and followed internet tutorials to get this working but once again, nothing.

  Now, I don't know what to do.

  Can someone please. I need access to the internet at home for College work as soon as POSSIBLE!

  Thank you!

  Hello

  I think you should start solving the problem by checking some key things:
  First the wireless network card should be recognized in the Device Manager and it must not contain any yellow exclamation point. The WLan driver must be installed correctly.

  Second, please check if the wireless network adapter is enabled. All Toshiba laptops media function keys and generally you can activate the WLan using FN + F8 keys or (in some cases Fn + F12)

  You should check the WLan configuration.
  You can add new Wlan profile in Control Panel-> network and sharing Center-> wireless (left)
  Add new Wlan connection.

  Note: use the exactly the same settings that were used in your router settings.
  Pay attention to the standard of encryption and the encryption key!

  In the Device Manager-> card Wlan-> properties-> Advanced tab, you can see options as for example WiFi 802.11 A/B/G standard, etc.

• Portege R500: BT & WLan need driver XP

  I'm trying to download the drivers for my Portege R500 (English) for Windows XP drivers Toshiba download site. In most cases, this went successfully, but both of them failed:
  -Bluetooth Stack (seems to be not not available).
  -Wireless Lan Driver, Intel, 11.1.0.100 references (if I click this link I am redirected to a site that is not found).

  It is really raise what you wrote here. I checked the download page and everything works fine.

  For BT stack download you will be redirected to BT support page http://aps2.toshiba-tro.de/bluetooth/index.php
  There, you can download and install the latest version of BT stack. BT monitor can be downloaded from the download page (1.73 MB zip file).

  All driver WLAN, you can read in your other display.

• Satellite L650-0ED - ports external monitor and turn off WiFi

  Hey,.

  1. I have a Satellite L650/0ED, I was wondering if the HDMI and the external monitor port start when starting and if they cause the start time of the laptop to be slower. If they do slow down the start how disable them you using Device Manager, since I looked, I tried to disable the Device Manager; but I can't find them anywhere on the list of devices.
  They have a special code name or something?

  2. based on my understanding, the manual of instruction/userguide Toshiba mentions if I press FN + F8 it turns off the wireless amber light but this is not the case, since the amber wireless is still or not. I have the wireless active or disabled.
  It say it's so I have the wireless off of amber or the - Orange must be turned off when I press FN + F8 and is not, why is this?

  Thank you

  Hey Buddy,

  1. No, they cause t a slower start. He doesn't know me and as long as I know it of not possible to disable the ports in the BIOS. Then n t you worry about this, even, you have connected external screens, boot time is the same.

  2. Yes, usually you can activate the WLAN functionality by using the FN + F8 key combination.
  I put t have the laptop in front of me, but normally if you don t have a hardware wireless switch, you can disable the wireless network adapter in the BIOS. Just put permits for disabled people and that should be all! :)

• WLAN on P100 connection problems

  I've just set up a Netgear router to my main computer and attempted to go wireless on my P100.
  My router signal is be picked up on the laptop, but when I try to connect, I get the message.
  "Another application of sellers is to control the wireless adapter.

  Any ideas how I can fix this problem?

  ConfigFree connectivity doctor is tool for LAN and WLAN monitoring and not for any type of setting up connectivity.

  If you want to configure WLAN settings you can do this using the WLAN Windows preinstalled OR Intel PROSet WLAN Client settings.

• Linksys Wireless Network Monitor Software

  I have Wireless-G Notebook Adapter v.5.0

  Need help to locate Linksys Wireless Network Monitor Software.

  I bought the Wireless-G adapter for 3 years ago and recently lost HD Crash.And software, I know that I have the disk somewhere, but cannot find it... still looking...  I tried looking for Cisco and could not find it.

  Any advice?

  Thank you

  
  

  

  I found it!, online.

  http://homesupport.Cisco.com/en-us/wireless/LBC/WPC54G

  THEN

  On the tab for:

  DOWNLOADS

  then SELECT BOTTOM LIST drop-DOWN select hardware version.

• WIndows 98 SE & WPC54G ver 3 (not ver 3.1)

  I had a problem get it running on my old laptop that is running Windows 98 Second edition.  I've been on the linksys support offerings direct tech, which has been very helpful, but have not found the solution.

  I tried to download the 3 different versions of the driver for the card of network 3 WPC54G ver & whenever I'm still getting a circle of yellow exclamation that the device does not work in Device Manager after updating the driver.

  I don't have the CD that came with the wireless network adapter.

  With the latest driver, I was able to get the monitor & functional, but it is not found the wireless network (which works & has been tested with another device) access point.

  With the version 2 driver I was able to type in the SSID & pre shared key, but I received an error message & he never found the access point.

  I also tried the 3.1 driver (even though it says ver 3 on mine, not a 3.1 anywhere), which seems to charge in, but there is no monitor to look again for the access point, so none if typing in the SSID & pre-shared key.

  In the driver all updates, I am asked for the disc of Windows 98 SE, but when loading the file still is not on the CD (which I confirmed by doing a search on the disc).  Then I typed in some places another file that I found on another thread in this forum & that usually seems to do the trick (C:\windows\options\cabs, C:\windows\system, etc.) but not for all versions of pilot.

  Any other ideas, or drivers that may work?

  I had already tried this, but thanks for the suggestion.  In addition, there is not a chance this old laptop could run XP.

  I was finally able to get the adapter to work in the hardware profiles, after a long night with the help of the direct support of linksys.  Unfortunately we could not always get the adapter to recognize the wireless network after you install the monitoring software for each version.  I then read in the software (version 1.3) Boingo wireless & who did the trick.  There the pilot of linksys and Boingo wireless monitor software.

• Error message WLMON or WLMON.exe, the missing files and WPC54G

  Portable running Linksys Network adapter card WPC54G

  OS: XP

  Driver version: 4.100.27

  I get an error message that WLMON.exe has no inialize, and a second pop up that tells me that there are missing files. Can someone tell me if there is a fix to this addition WLMON out of my boot ini and the devil made WLMON.exe? Did he get the same problem and have a solution?

  Do not install the Linksys monitor... just install the driver.

  Remove the Linksys adapter and uninstall the Linksys software menu programs... Re - install drivers insert the CD of Linksys install in your CD-ROM drive, when the welcome is displayed click on exit, connect your USB adapter now... When the Hardware Update Wizard window appears, click on install the software automatically (recommended) and then click Next... Click Finish when the installation is complete.

  Click Start and open the control panel and double-click on network connections. Right click on wireless network connection, and then select view available wireless networks "-If you see your network wireless in the list, the highlight by clicking 'single' on it now, click on the 'Connect' button below-if your wireless network is secured, it asks you to provide the network key - provide the wireless network key and confirm again in the confirmation box and click 'Connect'." It should work...

• How to enable the WLAN of Compaq 510 in Windows 7 Starter?

  Hi, since I was on the dial-up connection and turn off my WIFI connection, I don't know how to turn on my WIFI, when I click on the switch for WLAN, bluetooth on and it also shut down, I don't know how to activate it, please I need your help, as soon as possible.

  Hi Justin,

  Thanks for posting your query in Microsoft Community.

  I suggest to check the Autoconfiguration WLAN service and set it toAutomatic and check if the problem persists.

  a. click the Start button.

  b. type services.msc in the search box and press on enter.

  c. Locate the autoconfiguration WLAN Service and check if it set to Automatic & not automatic delayed.

  If you are still facing the same problem, then turn on tracing for a local wireless network when you start a Windows Vista-based computer.

  To enable tracing for a WLAN in Windows 7, follow these steps:

  a. click on start to reduce this includes this image and then type cmd in the box start the search .

  b. right click on cmd in the programs list and then click run as administrator.

  The collapse of this includes this imagIf you are prompted to confirm that you want to continue, click continue.

  c. type the following line at the command prompt and press ENTER:

  netsh wlan set tra persistent

  The monitoring starts immediately and is persistent. When you restart the computer, the tracking begins shortly after the start of the WLAN auto configuration service. Existing monitoring log files are overwritten.

  Note: To stop the follow-up after you activate it, use the following command:

  Netsh wlan set tra no

  For more information, please see: How to enable tracing for a LAN wireless in Windows (for Windows 7)

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• How can I activate my card wireless monitor mode?

  I would like to follow the data packets transmitted, any help would be appreciated.

  I am running windows 7 and my wireless card is aDW1501 Wireless - N WLAN Half - Mini Card

  Thank you

  Hi Sicarium,

  Please see article about network monitor:

  http://support.Microsoft.com/kb/933741

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think