WSC vs FMC

Similar Questions

• FMC 6.1 upgrade break my FTP

  Hello

  I have made a transition from my virtual FMC of 5.4 to 6.1 but kept 5.4.x on my power of fire ASA for a while. Nothing has changed in the rule set while I improved from 5.4 to 6.1, but the next day I applied the config of 6.1 to my modules of firepower I started to have a broken FTP transfer reports.

  It is a passive FTP transfer between two servers on two different subnets inspected by the firepower of ASA. The journal of the ASA reports the file was stored on the receiving server, but the sending application indicates a transfer error and that half of the file is actually stored.

  If I omit the flow of power to fire all the FTP works. I tried a few rules of fire power with or without the IPS, plain and records 'allow all' but nothing works.

  I always use ASA old FTP inspection services which I think intrudes. Think you folks?

  Edit: I did some trial and error and it seems that the inspections of the SAA FTP has no effect, it's the power of fire. If I create a special assignment for the work of specific stream transfer rule FTP. Accept the transfer with or without IPS, records or any other characteristic breaks.

  Concerning

  Fredrik

  I opened a TAC case and the only solution is to put a special assignment for the FTP Server rule. The other two options are not viable.

  Here's the bug:

  https://BST.cloudapps.Cisco.com/bugsearch/bug/CSCvb55994

• FMC 6.0 down - what is happening with the logging?

  Hi all

  I have following question: what happens with the newspapers of the sensors when your CMF (firepower Management Center) is out of service?

  I expect that the sensor records the newspapers locally, until the PSC is in place again.

  If so, how long can the sensor to store these logs locally? (disk space,...)

  Y at - it no document on this subject? I can't find this kind of information in the release notes or the Administrator's guide.

  Thank you.

  Hello

  If the CME is fails or communication problem between sensor and FMC, sensor stores newspapers locally and trying to send all together once the communication is in place.

  But yes, there is a limit based on different models and available disk space on them.

  Ideally, disk space must not cross 85% of usage and if so, the old events are pruned.

  If the largest camera store more events, then smaller.

• Version of the IOS taken ASA supported with WSC, 4.3

  Hello world

  We will deploy CSM 4.3 in our network.

  Need to know if we have ASA 5505 and 5515 and 5520 which version of IOS, we should have so that it can support CSM 4.3?

  Also can we get Windows server for CSM 4.3 user?

  Thank you

  MAhesh

  IOS runs on the routers and switches. The software on an ASA is simply called Software ASA.

  4.3 CSM supports ASA versions 7.0 to 8.6, although many features require ASA 8.0 or later version. Full details are listed here. If you deploy a new CSM, you should switch to the newer version of 4.4. It adds support for the ASA software up to version 9.1 (1).

  As described in the deployment guide (details here), CSM 4.3 requires Windows Server 2008 or 2008 R2. These requirements are the same for the WSC 4.4

• FMC will recognize not update version 6.0.1 - 1214

  Hi all

  In light of reviews cisco-sa-20160330-fp (CVE-2016-1345), an attempt to upgrade 6.0.1 build CME - 1213 build 6.0.1 - 1214 is not recognized.

  First attempt was to let FMC detect/download the update, but this resulted in the following message if poster "no new update currently available."

  Second attempt involved manually download the update (6.0.1 - Sourcefire_3D_Defense_Center_S3_Upgrade - 1214.sh) file of the site Web of Cisco and the Uploader on CMF and then try to install it. This resulted in the following message not "valid devices available for Sourcefire Defense Center S3 upgrade 6.0.1 3D - 1214." This update is intended for software versions higher or equal to 6.0.0 and less 6.0.1 - 1214. »

  This updated version 6.0.1 - 1214 is required to install the recent hotfix (Sourcefire_3D_Defense_Center_S3_Hotfix - 6.0.1.1 - 4. short), as shown in the download software page.

  Someone facing similar problems? All possible solutions?

  Thank you.

  MP

  Looks like they took this package on the download site.

  The fix for the CMF is however is displayed with a date of April 1, 2016:

  https://software.Cisco.com/download/release.html?mdfid=286259687&RelType...

  I was able to download and install successfully on my 6.0.1 - 1213 version virtual CMF.

  firepower_hotfix_success.PNG

  

• Windows Firewall and Windows Security Center cannot start. In addition, no WSC in the services.msc list. What should do?

  Hey guys. I looked up and down for a solution to this problem.

  I already tried this solution:

  http://blogs.technet.com/b/asiasupp/archive/2011/12/27/error-code-0x80070424-with-Windows-Firewall-and-quot-base-filtering-engine-service-quot-not-available-in-services-database-list.aspx

  Although the only problem is at last step when I turn on the firewall Windows or WSC (windows Security Center) since neither of them are present
  in the list of the services.msc.

  So here I am without any windows security, no firewall and no updates. I really need help here. I was attacked by malware, a day ago, and everything happened after that. I removed the malware with program ESET NOD, but it seems that the malware corrupted my registry/safety inputs.

  Thanks in advance.

  Hello

  I suggest you run both the fix that he mentioned below and check if it helps!

  · Resolve security issues to protect and secure Windows automatically

  · Automatically repair the settings of Windows security to secure your PC

  I hope that helps!

• Brother of FMC 9465 installed twice on LAN

  I installed by chance my brother MFC 9465 twice with the same ip address on my network local network. We are working correctly. other installation gives a remarq fault with that I want to cancel this second (erronously) facility seems to be unpossible. can anypne help my to cancel the second installation?

  Hello

  -What version of windows is installed on your computer?

  I suggest following the steps mentioned in the following Web site and let me know if it helps.

  http://welcome.solutions.brother.com/BSC/public/EU/GB/en/FAQ/FAQ/000000/000000/000071/faq000071_005.html?reg=EU&c=GB&lang=en&prod=mfc9465cdn_eu_as&cat=109

  How to remove network printers.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

  Hope this information is useful.

• FMC with 3 analog lines

  Hello

  I'm new to configuration of the CME, which asks your help for scenario below:

  We have the new branch opening, we have 3 analog lines:

  line 1:4444444

  line 2:5555555

  line 3:6666666

  We have cisco 2901 with CME license and cisco 2960 switch.

  Manager request below:

  line 1 must be used only by him (if any body call out or he wants to call someone)

  line 2 should be used only by the Secretary (if any body call out or he wants to call someone)

  line 3 should be used by all other employees of the branch (12 employees), if any outside body call it addressing the reception who forward your call to a particular person (can also be managing or his Secretary)

  all employees of should share extension (if the manager wants to call an employee or Secretary)

  Director, Secretary or an employee must press button 9 to call outside the lines.

  can you give me some configuration to reach above scenario.

  Thank you

  I think that you can try it and apply correct corlist in the ephone-dn.

  voice pots Dial-peer 937
  corlist manager out
  destination-model 9 t
  port 0/0/0<- analog="" line="" for="">

  voice pots Dial-peer 938
  outgoing Deputy corlist
  destination-model 9 t
  port 0/0/1<- analog="" line="" for="">

  voice pots Dial-peer 939
  corlist out more
  destination-model 9 t
  port 0/0/2<- analog="" line="" for="">

• In FMC 6.1 IP address range

  Hello

  How to add a range of IP addresses in the management of the power of fire Center version 6.1
  (Example: from 192.168.1.1 to 192.168.1.50) range (192.168.1.1 - 192.168.1.50)

  I can't find the proper syntax...

  Best regards

  Eric

  Eric,

  Your example is the second address lower than the first. Reverse their and it should work for you.

  See the following I just did on my 6.1 CME (opens in a new tab to zoom in):

  fmc_network_object.jpg

  

• Cannot add ASA at WSC, 4.3

  Hello

  I am trying to add ASA to CSM 4.3 through the addition of network devices.

  ASA has been with http server ip config and then mask int

  I get error https

  The connectivity test failed. Elapsed time: 127 seconds.  Unable to communicate with device no response to the attempt to connect to this unit, please check the following items and then retry the operation. (1) the 'IP address', Protocol and Communication Port are correct.

  (2) there is the network connectivity between the CS Manager server and the device.

  (3) the device is configured to accept http/https connections. Discover political IPS for IOS devices or IPS, http/https connections must be enabled otherwise discovered political IPS should be disabled.

  (4) the unit is running.

  CSM server is conencted to the interface of the ASA.

  Concerning

  Mahesh

  An easy way to doublecheck is so see if you can launch ASDM on the CSM server and connect to the firewall.

  ASDM both CSM rely on the same connectiivty of https.

• Max FMC. number of manageable devices

  Hello

  What we have here is a virtual CMF with a maximum number of 25 handy devices (FS-VMW-SW-K9). In fact, we have less than 25 device but in the future the amount will rise above this limit. (26 to present)

  What can be done to extend the maximum number of devices managed by that firepower Managent Center?

  Do we not have to replace the virtual CMF with a FS2000? It's big but the FS1500 is already the end of the sale. Or can we add an additional license (FS-VMW-2-SW-K9 for example)?

  Thanks for your help.

  Hello Karlheinz,

  Using a virtual CMF, 25 corresponds to the maximum number of devices that you can manage. More than that, you can't manage by using any kind of license.

  If you need support more devices then I would suggest FS2000. F1500 is already end of sale until its not possible to go with it.

  Consult the data sheet once because you're more familiar with your needs.

  http://www.Cisco.com/c/en/us/products/collateral/security/firesight-mana...

  Feel free to let me know if you have any questions.

  Note If this answer can help you upon your request.

  Concerning

  Jetsy

• wie installiere WSC ich

  ICH möchte Center solutions Windows installieren

  Please select your language from the drop-down menu at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below:

  Bitte wahlen Sie your Sprache aus der Dropdown-list am another Rand der Seite, um your question in der Sprache your Wahl zu schreiben. DAS Forum Sie ist nur as Englisch geschrieben. Wenn Sie nicht find, die gewunschte Sprache oben support options as international locations können über den following link unten found werden weitere

  http://answers.Microsoft.com/de-de/windowslive/Forum?tab=unanswered
  http://support.Microsoft.com/common/international.aspx

• My pc with UEFI windows8 was able to start at the WSC windows8

  I don't know if it's supposed to happen, but recently I wanted to install windows7 and I put my system in legacy mode and came a message saying that I wouldn't be able to start the operating system. To restart my system, Windows8 was able to boot to the CSM. If it's supposed to happen? When I changed it to UEFI also started. My system can start at windows 8 in the two MCS AND of UEFI?

  Hello

  Thanks for the reply.

  As you have Windows 8 on your computer, there is no point on what you can not use Windows 7 installation. But, you can install Ubuntu in another partition and use it by disabling the UEFI mode and secure boot options.

  Let us know if you have any additional questions.

• FMC Cutting Master format - is this in CS5?

  I have been using Premiere Pro CS4 to produce a documentary HDTV Bluray, I do my final rendering, I was preparing to send to the duplicator to master production of glass & first copy center run, then I found the duplicator wants a cmf (cutting master format) file, this is the only input file format allowed for bluray per this facility & CS4 didn't do not is so unable to do Bluray projects end to end (I thought their sales literature that she would pay).

  So now I have to buy another software.

  If someone knows if Adobe added support of CME in CS5?

  Roxio DVDit ProHD, Sonic Scenarist, SONY Blu Print & NetBlender DoStudio can all produce this type of image.

  In addition, it seems that most replication houses will also require a roughly $ 500 / layer and $0.04 / fresh AACS drive.  (AACS is not optional copy protection required for all the stamped BD didks.)

• Satellite U940 PSU6VA - Dual boot with Ubuntu based distributions

  _ * My specifications: * _
  * Model: * Toshiba Ultrabook (Satellite PSU6VA - 00S 002 U940)
  * Operating system: * Windows 8.1 x 64 (upgrade of Windows 8 x 64)

  I would like to set up my computer to dual boot with Windows 8.1 (x 64) and Zorin OS 9.1 (64-bit).

  ZORIN OS is a derivative of Ubuntu which maintains a binary compatibility with Ubuntu i.e. Ubuntu and Zorin use the same drivers and can run the same applications. John Damascene is more or less just Ubuntu with a different desktop environment and some additional preinstalled applications.

  So far, I know that I need to disable the QuickStart Windows 8.1. What I have to do something else (for example disable Secure Boot, CSM, etc.)?

  In addition, my Ultrabook comes with 2 hard drives: 500 GB HARD drive and a 30 GB SSD. Windows uses the HARD disk for storage and for implementing SSD caching, through technology Intel Rapid Storage Technology. Is it possible to set up John of Damascus to do so (preferably without disabling caching on Windows)?

  NOTE: I prefer to do things using graphical interfaces, rather than the CLI. I don't mind given CLI instructions; also just showed me the GUI equivalents if possible. I use the CLI if there is no alternative.

  Post edited by: Justinian

  Hello

  See my responses / comments among your questions (I took part of your message and inserted here):

  So far, I know that I need to disable the QuickStart Windows 8.1. What I have to do something else (for example disable Secure Boot, CSM, etc.)?

  Answer: If you want to dual-boot, do NOT select WSC as preventing Windows to start.
  You shouldn't have to disable startup secure either, but I can't promise that. I think that Ubuntu 14 has support for secure boot.

  In addition, my Ultrabook comes with 2 hard drives: 500 GB HARD drive and a 30 GB SSD. Windows uses the HARD disk for storage and for implementing SSD caching, through technology Intel Rapid Storage Technology. Is it possible to set up John of Damascus to do so (preferably without disabling caching on Windows)?

  Answer: No, I don't think that there is a way to use the SSD in Zorin without making it unusable for Windows.
  Suggestion - let it be.

  Tom BR