XenServer multipath.conf (blacklists EQL via multipath.conf)

Similar Questions

• Query EQL via WS

  Hello
  
  It is a follow-up on a previous thread in the forum:
  Query EQL in Conversation WS
  
  As mentioned in the thread, I am able to apply for WS using the structure defined in the wire to make an EQL query and return the results.
  However, when you try to programmatically, I noticed that the ContentElementConfig node has any child nodes, and still less the node LQLQueryString, defined in the WSDL file.
  
  I know that Julia has mentioned in the post that studio components using the parser NQL Different service first before using the chat service, but someone could throw some light on this and this as the good order and procedure of making a query EQL to the server via the short services?
  
  Thank you!
  Chris

  Chris,

  Programming language you are using? I think that the exact response will depend on that as LQLQueryString is defined (essentially) as an extension of the string type.

  Using your example above, the following c# Code would hit the chat service correctly with your NQL Different statement (assuming that a namespace defined reference Web of Endeca.Conversation23):

  >

  Create an object of the request
  Endeca.Conversation23.Request req = new Endeca.Conversation23.Request ();

  Create your object LQLConfig, NOTE: the .NET path sets up its links, you use it. Item property to set the LQLString
  Endeca.Conversation23.LQLConfig lqlConfig = new Endeca.Conversation23.LQLConfig ();
  lqlConfig.Id = "myConfig".
  lqlConfig.HandlerFunction = "LQLHandler";
  lqlConfig.HandlerNamespace = "http://www.endeca.com/MDEX/conversation/1/0";
  lqlConfig.Item = @ "SELECT SUM (FactSales_SalesAmount) AS RETURN statement
  WHERE (DimDate_FiscalYear = 2008) AS Sales2008,
  Sum (FactSales_SalesAmount) WHERE (DimDate_FiscalYear = 2007) AS Sales2007,
  ((Sales2008-Sales2007)/Sales2007 * 100) AS pctChange,
  countDistinct (FactSales_SalesOrderNumber)
  TransactionCount GROUP;

  Add the Config NQL Different to list the ContentElements
  Conf [] Endeca.Conversation23.ContentElementConfig = new Endeca.Conversation23.ContentElementConfig [] {lqlConfig};
  forced. ContentElementConfig = conf;

  Set cross it and the vacuum State
  forced. PassThrough = new Endeca.Conversation23.CatchAll ();
  forced. State = new Endeca.Conversation23.State ();

  Hit the chat service quick start on your local instance of the server short
  CPC Endeca.Conversation23.ConversationPortClient = new Endeca.Conversation23.ConversationPortClient ("ConversationPort", "http://localhost:7770 / ws/conversation/quickstart?") WSDL");"
  Results Endeca.Conversation23.Results = cpc. Request (req);

  I hope that aid and it is easy to read, the tools of the forum for the formatting are not large.

  Kind regards

  Patrick Rafferty
  http://branchbird.com

  Edited by: Branchbird - Pat on October 18, 2012 11:00

• Conf material Bridge works not

  Hi all

  We have 9.1 CM and added cisco 2901 gateway H323 and configured hardware conf bridge router and it worked a few days ago, our point of arrival and Cisco sx 20 MX 300, registered the CUCM, using 2 SX20 and a MX300, video working fine and sccp Sh connections cmmands calls showed the call details of when endpoints used the Harware conf resrces , but now the problm is when attempting to conference between three enpoints, an audio endpoint only points. and also HS sccp connectiosn command is not shwing none plays, one hears the end points not using equipment for calls vieo cnf is the question

  Please sugest me how to solve this

  I already checked MRG assigned to endpoints and bridge Conf also enrolled in cucm

  Reset it via CUCM, do no sccp/sccp on the router, remove and re-create the profile or review traces CUCM and IPVMS.

• ACS - configure the authorization of shell commands to work under the configuration mode (conf t)

  Hello world

  I'm trying to set up a shell commnds set orders (including t conf mode) will be allowed, with the exception of administrative commands, such as writing, copy, admin, format etc.

  He worked for the commands in privileged mode (most) (such as writing and copy), but did not order t conf mode. It is important to prevent users to perform the ' write for the "and" copy run start "commands, for example.

  Here is the entry in the series of command shell (Partial_access) approval:

  Unmatched orders: permit

  List of commands:

  Admin

  copy

  delete

  do

  format

  To write

  (Relevant) group settings:

  V - shell (exec)

  Privilege level of V - 15

  Shell command authorization set

  Assign permission to command Shell Set to any device network - Partial_access (group name)

  I use CiscoSecure ACS version 4.2 (0)

  Thank you

  Lior

  Hi Lior,

  Please make sure you typed in the AAA client, the following commands: -.

  AAA authorization config-commands

  Thanks for posting your AAA client configuration via "run sh |" I have aaa "and if possible your configuration of privilege"

  HTH

• Multipathing with SW iSCSI initiators

  Hi all

  Just curious about the multiple and iSCSI paths. Summer hope to clarify a certain number of things.

  Taking an example of a single ESXi 4.0 host to connect to a device iSCSI via a network using a software initiator.

  
  A vSwitch was created on the host with two rising vmnic (two assets), which are connected to the storage network. A unique VMkernel port group was created on the vSwitch with an IP address on the storage network.

  Issues related to the:

  1 have I reason to think that the configuration above do not use the two vmnic for redundancy? I assume this is the case, because it shows only a single path under the storge device?

  2. assuming that the above is correct, that if I lost any vmnic is used, I'd lose access to my storage of this host?

  3. in order to provide redundancy in case of a failure vmnic, do I need to follow the steps in the configuration guide for iSCSI SAN? (http://www.vmware.com/pdf/vsphere4/r40/vsp_40_iscsi_san_cfg.pdf) That is to create two groups of ports on the vSwitch using vmnic active replacement (with the other unused) and use the CLI to create paths?

  4. If the default config is indeed only using a single VMnic, how can that be used?

  I think I already know the answer above but would like to have a validation...

  Thank you

  Chris.

  Tru Multipathing, your storage space must have at least 2 IP addresses.

  Do not confuse redundancy with multiple paths.

  While the two work together, you can have one without the other.

  To get full redundancy and multiple paths, at a minimum, your storage server needs at least two interface IP. you need to implement a vSwitch with 2 groups of VMKernel ports, as you mentioned below. #3 and port, then bind using the CLI.

  The political path roundrobin when value over (if your table is compatible).  You should then have 2 active channels.

  In your current config.

  # 1 there is redundancy, but no multipath

  # 2 No.

  #3-Oui - preferred method for many reasons with HA, path table and load balancing selection.

  #4-is not easy to find (at least not for me).  It really depends on how your political grouping vswitch is implemented.  Bad this refer to the experts.  Don't want to confuse.

• EqualLogic Multipathing plug-in - issues with linking using setup.pl

  I get this error when I try to get the Module of Extension Multipathing EqualLogic to configure my ESXi 4.1 box.

  Could not bind vmk1 one iSCSI adapters.

  I have a Dell M710 server. There the Broadcom 57711 NIC with load HBAs iSCSI hardware.

  Here are the steps to reproduce the problem:

  Installed ESXi 4.1 on host M710

  ESXi host configured with a password

  ESXi host configured with the IP address settings

  Connected to my vMA host (who has a local copy of the DELL-eql-mem - 1.0.0.130413)

  vifp addserver 192.168.110.63

  vifptarget s 192.168.110.63

  ./Setup.pl--installation--server = 192.168.110.63 - bundle = dell-eql-mem - 1.0.0.130413.zip

  I then reboot the ESXi host

  Once restarted

  vifptarget s 192.168.110.63

  ./Setup.pl--configure--serveur = 192.168.110.63 - vswitch = vSwitchISCSI - mtu = 1500 - NIC = vmnic6 - ips = 192.168.102.98 - subnet mask = 255.255.255.0 - vmkernel iSCSI - groupip = 192.168.102.40 =

  Then, it produces the following output:

  Network iSCSI Multipathing configuration:

  vswitch = vSwitchISCSI

  MTU = 1500

  NIC = vmnic6

  IPS = 192.168.102.98

  subnet mask = 255.255.255.0

  VMkernel = iSCSI

  EQL group IP = 192.168.102.40

  Creation vSwitchISCSI vSwitch.

  Definition of vSwitch MTU to 1500.

  Creating portgroup iSCSI0 on vSwitchISCSI vSwitch.

  192.168.102.98 to iSCSI0 IP address assignment.

  Create a new bridge.

  The addition of link rising vmnic6 to vSwitchISCSI.

  The definition of new uplinks for vSwitchISCSI.

  Definition of uplink for iSCSI0 on vmnic6.

  Could not bind vmk1 one iSCSI adapters.

  Argh

  So I use the vSphere Client to remove the switch, he created (and vmk etc ports)

  I then try again, this time with software instead of hardware iSCSI iSCSI

  ./Setup.pl--configure--serveur = 192.168.110.63 - vswitch = vSwitchISCSI - mtu = 1500 - NIC = vmnic6 - ips = 192.168.102.98 - subnet mask = 255.255.255.0 - vmkernel iSCSI - nohwiscsi - enableswiscsi - groupip = 192.168.102.40 =

  Which produces the following output:

  Network iSCSI Multipathing configuration:

  vswitch = vSwitchISCSI

  MTU = 1500

  NIC = vmnic6

  IPS = 192.168.102.98

  subnet mask = 255.255.255.0

  VMkernel = iSCSI

  enableswiscsi = 1

  nohwiscsi = 1

  EQL group IP = 192.168.102.40

  Creation vSwitchISCSI vSwitch.

  Definition of vSwitch MTU to 1500.

  Creating portgroup iSCSI0 on vSwitchISCSI vSwitch.

  192.168.102.98 to iSCSI0 IP address assignment.

  Create a new bridge.

  The addition of link rising vmnic6 to vSwitchISCSI.

  The definition of new uplinks for vSwitchISCSI.

  Definition of uplink for iSCSI0 on vmnic6.

  Activation of initiator SW.

  Permit SW initiator.

  Could not bind vmk1 one iSCSI adapters.

  Ugh once again.

  What I'm missing here? The commands that I use to setup.pl are actually given to me by setup.pl when I use the option - command sets:

  ./Setup.pl--configure--server = 192.168.110.63

  It has a nice Wizard that you ask all the questions, then tells you what is the actual command to use.

  I know that my steps using only 1 network card but I started using 2 network adapters and 2 IP addresses but it gave me the same error. For troubleshooting purposes, I decided to use only 1 network card and 1 IP to test. I also tried vmnic7 instead of vmnic6 with a different IP address but no luck.

  I tried a fresh install of ESXi twice.

  A huge 10 points to someone who can solve my problem

  VCP3 & VCP4 32846

  VSP4

  VTSP4

  Updated the commands I used wrong vifp instead of vifptarget, the problem still exists, but tried to fix this error.

  Box293,

  Which, in my opinion, happened is that vmk1 is already bound to something, the iSCSI Software card or hardware iSCSI adapter, possible earlier attempts or possible to have the classic configuration path fixed on this server - less certain on this second possibility.

  Deleting a key vmk from the GUI does not cancel the bindings, this must be done from the CLI with the command 'esxcli swisici '.

  esxcli swiscsi nic list d vmhba37 # lists all interconnect them related to hardware/software iSCSI card

  esxcli swiscsi nic remove - n vmk1 d vmhba37 # this will remove the binding vmk1

  Do these steps should help you clean any link you have.

  A lazy way to clean the link would be to re - install ESXi

  I hope this helps.

  David

  Reference Dell | Used EqualLogic

• Reference Dell EqualLogic Multipath (e/s high flow)

  We recently bought a Dell EqualLogic SAN. Our main goal for this device was to begin to use pools of resources and be able to do a few HA and Live migration. We have worked with XenServer and Xen Cloud for a while and got no e/s on iScsi performance we were hoping for. With the help of Multipath on the main host machine we get on 250 Mbps (which we are satisfied). On the guest computers, we get only 120 Mbps.

  My question to the community of VMWare; If we wanted to use products VMWare is the possibility to get more then 1 Gbps i/o throughput on a guest PC? And if so, if it is a PDF or a post somewhere that could explain how to do this?

  Let me know, thanks!

  Clinton

  The doc of the correct configuration is attached... hope that her little help. In my view, it is also sub TR docs when you save your table PS.

• Should I sysctl.conf in El Capitan?

  Hi all!

  The title of my query in fact already said it all.

  I'm a bit confused because EtreCheck says:

  Configuration files: ⓘ

  /etc/sysctl.conf - file exists but not expected

  The info finder said the file was created and modified on June 2, 2010 and I strongly suspect that he just moves along in the process of migrating my old iMac (mid-2011 with OS X 10.7.5) to a new (mid-2014) now under OS X 10.11.6.

  So the question is, I need this file or can I safely delete it?

  Oh, and while we're... EtreCheck also said:

  Configuration files: ⓘ

  / etc/sudoers, 2622 but file size expected 2299

  That's what worry? And if yes, what is the name of the problem and how can I solve this problem?

  Loads of thanks in advance!

  You might find the article in the link below.

  https://eclecticlight.co/2015/12/31/El-Capitan-does-it-deal-with-network-CONGEST ion to the last.

• Firefox does not start when DYLD_FALLBACK_LIBRARY_PATH in launchd.conf

  I need to configure DYLD_FALLBACK_LIBRARY_PATH for another application but when I do this Firefox launch more correctly... empty shell resembling Firefox opens. (Located in launchd.conf and requires a reboot)

  An easy test is to use the Terminal and set the bashrc with variable... then launch Firefox from Terminal... with this variable set env Firefox isn't happy.

  This may shed some light on the functionality of this variable http://superuser.com/questions/282450/where-do-i-set-dyld-library-path-on-...

• Syntax error line 43 of swupd.conf

  I get error messages repeated in the swupdate errorlog:

  Syntax error on line 243 library/software/Server Update/Config/swupd.conf:

  Invalid address or port

  Here's the line 243 of this file:

  To listen *: 0

  Everyone see what is the problem? This error seems not until I have reset the swupdate service by removing catalogs and downloads and restart the service.

  Thank you!

  Dean

  To listen *: 8088

• location of the OSX Server smb.conf

  Anyone know where the smb.conf file? I would like to take a look at its contents.

  If you mean nsmb.conf (5), it does not exist by default, but if you did, it would be in/etc.

• DocumentRoot in niwebserver.conf (LabVIEW 2009)

  I use the built-in web server of LV2009 and try to make my way through the creation of a stand-alone application.  So far, I've done pretty well, but I have some questions about the directives in the configuration file of the web server.  There seems to be conflicting information in the forum on the directives of path, so I'd like to pin down here.

  The two positions that seem to relate to what I've found directly are:

  http://forums.NI.com/NI/board/message?board.ID=170&message.ID=434722#M434722

  http://forums.NI.com/NI/board/message?board.ID=170&message.ID=393057#M393057

  Thus, can the path used for DocumentRoot be relative?  And if so, to what?

  Ideally, I would like to have this compared to the configuration file (which seems to be stated in the first post above).  However, it may be that the path is compared to the web server itself (as inidicated in the second post).

  Thanks for the clarification!

  James

  Hi James,

  I believe that your first link to the post of NathanK is correct. He says there that "in 2009 all paths relative in niwebserver.conf are relative to the location of the config itself". If the path can be relative and the path to the webserver.conf file.

  I think that the difference of its two positions is because the position in your second link about LabVIEW 8.6, while the post in your first link is about LabVIEW 2009, as well as information on the differences between the two versions.

  Kind regards

  Stephen S.

• Impossible connection postgresql, error psql: FATAL: no entry for the host pg_hba.conf ": 1", user 'eware', database 'eware.

  Original title: I am facing below errorpostgresql

  I have windows 12, I am unable to connect postgresql. I am faced with error below

  psql: FATAL: no entry of pg_hba.conf to host ": 1", user 'eware', database 'eware.
  ", SSL off.

  I have windows 12, I am unable to connect postgresql . I am faced with error below

  psql: FATAL: no entry of pg_hba.conf to host ": 1", user 'eware', database 'eware.
  ", SSL off.

  Hello

  There is no Windows 12.

  And "postgresql" is database software open source.

  I suggest that you ask for their support link:

  http://www.PostgreSQL.org/support/

  See you soon.

• I can't get adobe to work and when I look in ms confing is shows that it is stopped and does not work how can I run past

  i cant get adobe flash player to work and when I look in ms confing is shows that he is arrested and does not work how can I change to run again

  Hello

  This can help you:

  Download and run the Flash Player uninstaller program.

  http://helpx.Adobe.com/Flash-Player/KB/uninstall-Flash-Player-Windows.html

  Then download and install Flash Player; After unchecking installing Chrome and Google toolbar option:

  http://get.Adobe.com/flashplayer/?promoid=BUIGP

  If the problem persists, you may want to ask in the Forums of community Flash Player:

  http://forums.Adobe.com/community/flashplayer

  See you soon.

• Module Extension Dell EqualLogic Multipathing v1.4 missing setup.pl

  The new v1.4 Dell EqualLogic Multipathing Module of Extension is missing setup.pl script.

  Hello

  Thank you.  A new package is created.  In the meantime, you can try the setup.pl v1.3...   Or use alternative methods to install it.

  Feel free to open a support on this file as well.   They can add you the question open with genius.

  Kind regards

  Don