XPS 8300 nine connects to the Broadcom Netlink Communication card only after restarting 3 - 4 times at cold start.

Similar Questions

• Broadcom netlink gigabit card does not connect to 1 Gbit/s, auto negotiate connects to 10 Mbps

  Hello

  I am very satisfied with my purchase Alienware Aurora ALX and happy to be part of this community.  However, I have this problem:

  Does not connect to 1 Gbps Ethernet adapter; Here's what I've tried so far:

  (1) confirmed that my router is able to support Gigabit Ethernet.  I have two other devices connected to the same speed (an old PC and NAS).

  (2) when I set the speed and duplex of the adapter auto negotiate, it will connect to 10 Mbps

  (3) I noticed that there is no setting for 1000 Mbps in speed and duplex options.

  (4) I tried 100 full duplex MB, it will connect, but my Internet connection slows down less than 1 Mbps (I'm on a 15Mbps connection and test the other PC it could reach around 14Mbps).

  (5) I then tried 100 MB half duplex, it will also link and my overall network performance is good.

  (6) I have confirmed that I have the current driver from Dell. I've had the computer for 3 days (using windows 7 by the way).

  (7) I tried all ports on my router and confirmed that the side of the router has also been on auto negotiate and not trying to force a specific speed.

  I hope someone has a solution or suggestion for this problem.

  Kind regards

  Jason

  * SOLUTION * thanks in part to the previous article.

  Here is the Giga speed solution that worked for my new Dell Studio 1458.  I've read a lot about speeds slow xfer using the Broadcom NetLink LAN connection.

  There were two things I did not initially, but were in fact true.

  (1) you must use a CAT 6 line on ALL your machines capable of gigabit.  I though that a good line of Cat5e support giga speeds.  This isn't.

  Card Dell NetLink is apparently, some initial negotiations with your router (a bit ' as a fax machine), then after seeing all of your connections.

  It will drop the xfer rate down to the lowest common component (i.e. the Cat5e cable).  And;

  (2) map of NetLink won't give you giga speeds in automatic selection (advanced ethernet properties, speed & duplex).  The speed and the duplex window will never

  view 1000 MB!  You can check if your is10/100/1000 connection by double clicking on the icon of your connection to the Local network.

  I checked the speed of my connection giga via a test utility and transferring a 200meg file.  The results indicate an increase in the speed of 12 MB/s to 26 MB/s.

  These figures do not show a factor of ten speeds increase, we'd all have (so much), but they are in line with transfer rates of others.

  I hope this helps!

• Hi, I installed an Alfred Workflow (see code below) that will mark all my mails as read. After you run it for a minute, the mail has crashed and I had to forcequit. However, now, when you open the Mail it crashes instantly, even after restart and repair o

  Hello

  I installed an Alfred Workflow (see code below) that will mark all my mails as read. After you run it for a minute, the mail has crashed and I had to forcequit. However, now, when you open the Mail it crashes instantly, even after restart and repair the permissions. I also used the Ctrl + C and CTRL-Z commands in the Terminal to leave the alfred_script, but nothing helped. I'm running out of ideas here, so I hope you could help me either reinstall the mail.app. I could always just switch to a different mail application, but it's kind of a last resort.

  Code:

  Tell application "Mail".

  Define allAccounts on each account name

  Repeat with currAccount in allAccounts

  the unreadMboxes value (each mailbox to the account currAccount the unread number is not 0)

  Repeat with currMbox in unreadMboxes

  (read status of each message to currMbox including the playback State is set to false) true value

  end repeat

  end repeat

  tell the end

  Any input would be greatly appreciated. Can post the report of crash on demand.

  Not sure that Alfred's, but it's just an Applescript script and it would not cause Mail to be planted.

  However, when running through all the messages, it is possible Mail database has been corrupted and it crashes because of this.

  I'll probably get anything out of the accident report, but others might.

  My first instinct would be to rebuild the mailbox. Because you can't do that with him crashing, you can simply delete the databases and it will rebuild them.

  Navigate to this folder:

  ~/Library/Mail/v3/MailData/

  You can either manually through the files, or copy the full path and paste it into go the folder in the menu go to the Finder.

  Remove the envelope Index files. Open Mail and see if it works well.

  If your library does not appear in your folder, hold down the Option key and select library in the menu go to in the Finder.

• XPS 8300: Can I put the food?

  I would like to upgrade my power supply for my XPS 8300 to something with 500W or later. Exceeding of several internet forums, it seems that some people were able to do, but they need to change in order to adapt because the exclusive Dell power is shaped differently.

  I opened a discussion with Dell and said then that the "maximum power to the system would be 460w", which means that I have no option to upgrade.

  Can anyone else confirm this? It seems fairly ridiculous that Dell would bother someone to upgrade their system this way.

  BadgerKing

  Yes, generic ATX power supply can be installed, with a power of 20 + 4 pin main motherboard, or 24 pins as the XPS 8300 has a panel back open, with or without the on/off switch.

  You should be able to buy a compatible power supply either a local computer or online store.

  Note: A power supply with four SATA power connectors, is necessary.

  It was reported that it is better to buy a PSU with a depth of approximately 5.9 ".

  Bev.

• How to set the number of connections to the server. I am rejected after three connections.

  The following message appears when I consulted three folders in my email...-'unable to connect to the IMAP server. It may have exceeded the maximum number of connections to this server. If so, use the advanced settings of the IMAP Server dialog box to reduce the number of cached connections. »

  You can connect to an IMAP server as often as you like, BUT...
  You can restrict the number of simultaneous channels that are open during this connection.

  Thunderbird sets a default limit of 5.
  You can go higher on some servers, or you can go as low as 1.
  Try to set the limit of connection for 3

  "Tools - account settings - [select your account] - server settings - [settings of the server] - advanced - maximum number of connections to the server for cache - [enter 3]"
  If it is already set to 3, to descend more down - 2 or even 1.
  Out OK

  TB - 38, Win - PC 2

• Apple TV / Hue lights have no internet connection (but the phones and computers do) - only disconnect Time Capsule fixed guess?

  Hello

  My Apple TV will sporadically lose access to my iTunes library (despite showing the connection and a signal strong) and Netflix will not play.  My tint lights are not recognized when this happens.  When I restart the AppleTV, then it shows that they are not connected to the internet.  However, my computer and the phone still have functioning wifi in these proceedings.

  The only thing that seems to restore connectivity is when I unplug my Time Capsule (version 7.7.7) and then plug it back in.  Can anyone offer solutions and the potential causes?

  Thanks in advance for your time and help, it is greatly appreciated.

  I don't have a simple answer to why not a quick fix to fix things.

  There are plenty of things you can try. None are guaranteed to fix things... but he is able to increase your blood pressure and make that upset you.

  Then. I need more information.

  What ISP modem or router do you use? Brand and model please.

  Who is the provider?

  How did the TC connected to it? What mode it's in, bridge or router?

  Is the wireless on the ISP router turned on?

  You have an excessive number of routers wireless around you?

  Use diagnostics wireless on a computer to check.

  You never reset the TC at the plant after the update of the firmware?

  If this isn't the case, please do so now. Redo the installation in accordance with the following instructions.

  Universal factory reset

  Turning off the TC... That is, remove the power supply cord or the power at the wall outlet, wait 10 seconds... Hold the reset button... be nice... Turn on always even now in reset... and keep holding in for another 10 seconds. You may need assistance because it is difficult to hold in reset and power on. It will show the success quickly flashing led front. Release reset... and wait a few minutes for the TC to reset and return with the factory settings. If the front LED flashes quickly you missed and simply try again. The reset is quite fragile in these... Press the key while it is just click away and not more... I've seen people bend lever or even break. I use a toothpick as a tool.

  NB. None of your files on the hard drive of the TC are removed... This simply clears the settings of the router of the TC.

  The installer the TC.

  And then redo the configuration of the computer with Yosemite.

  1. the use of very short names... NO APPLE RECOMMENDED names. Without the space and pure alphanumeric characters.

  for example TCgen5 for the base station and the name of the TCwifi wireless. (try to keep names < 10 characters)

  If the problem is using wireless TC24ghz and TC5ghz with fixed channels like this helps.

  2. use all passwords also consistent with 1. but maybe a little longer. IE 8 and 20 characters of mixed cases and numbers... no alphanumeric non-caracteres.

  3. If the TC is router, you can ignore this point. It is only a problem when the TC is bridged.

  If ensure that the TC is always the same IP address... you will need to do this on the main router using a dhcp reservation... or a bit more complex setup by using the static IP address in the TC. But it's important... the IPs derived in all directions when Yosemite do not remember his name for 5 min after a reboot done for poor network management.

  I highly recommend this method on bridge of situation where you have the ISP router.

  https://discussions.Apple.com/message/25135547?ac_cid=tw123456#

  4. Please tell us if your ISP is now using IPv6 as who introduced a new set of questions.

• Pavilion dv6700: white screen permanently after connecting to the projector (stuck in "projector only" mode)

  Hello community,

  Here is what happened:

  I have connected my laptop to a TV via HDMI and set the display option to show the "projector only" in the Panel.

  The fn functions do not work and have never been, probably because I, at some point, off the never installed or quick launch buttons driver after the transition from Vista to Win7.

  With the TV still plugged, I closed the laptop.

  Now, when my device is restarted, the screen remains black.

  Connect to the same or other TV sets via HDMI won't show 'no signal' on the TV.

  Connection to an external display or projector via VGA will show either no signal.

  So I presume this must be the source parameter, which would need to be changed back, but I have no idea how to do that blindly. Anyone got any ideas how I could solve this problem?

  I thank very you much in advance!

  Fixed drawing of one of the two RAM Modules. Just like that.

  Hope this can help others to solve the problem.

  What has not helped:

  • Permutation of these two RAM modules and then start.
  • Reset the BIOS by pressing the keys Windows + B while pressing the power button.
  • From the BIOS menu by (several times) by pressing f8 or f10
  • Pressing on the power while pressing fn + f4 button
  • Let start normally and then by pressing Windows key + P
  • Choose different start-up options blindly with the arrow keys and enter

• Slow connection with the built in WiFi card

  I have a connection wanadoo adsl internet 20 Mbit family with a direct box. The box is also a wireless router.
  When I connect to the livebox with my toshiba mx40-231, the connection is very slow. The connection is constantly switch between 1 Mbps and 54 Mbps and speeds range between. It is also the problem. One moment an internet page is send in 1/10 of a second and 1 minute later a page to load in 20 secconds! the strang thing is that the intensity of the signal is constant high!

  With the direct box, I also had a wireless USB key. When I use this stick I get a connection very quickly 54 Mbps constant.

  It seems to me that the construction of the wireless card is the problem. I already have the latest wireless driver and tried a few channels on the router.

  Someone at - it an idea to solve this problem so I can throw this wireless stick :-) Thing very clumpsy this stich on such a portable wireless of beautifull!

  Hello

  If you check the wireless card, you will find many topics on this subject. We know that Intel 2200 B/G card wireless make disorders and connection is not constant. We can only speculate why this happens, but the fact is that this card has problems with different routers.

  For example: Satellite M40 has the same card and the fantastic work with Netgear router. Even with Belkin, it works well in full speed.

  I recommend you to install the latest version of the driver Intel

  Good luck

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• Connect to the result of local wireless only router and can not go to the internet

  My fujitsu laptop (Windows Vista) to connect to the router wireless home successfully during a month and suddenly 'local only' and cannot access the internet. force wireless is strong and my other laptop with Window XP connect to the internet successfully with the same router.

  And my laptop can connect to the internet using the wifi system in my school without any problems.

  Please help to restore my laptop to the internet via my wireless router.

  Thank you!

  Geofg,

  I have a similar problem after the most recent update of Windows. My IPv4 network properties manually configured outside the range of the DHCP from my router. This is so that I do not receive IP addresses different natted attributed to my computer.

  After the update of Windows, the IP address of the GATEWAY is cleared after each restart of the operating system.

  If you use the manual IP settings, check to see if this can happen to you.

  HTH!

• Cannot connect to the network or perform system restore after installing updates have been

  WIN 7 Home Premium running on a gateway PC connected to the internet via an ethernet connection using a RealTek network adapter for the past 5 years with no problems. Running Avast Pro antivirus / internet security.  09/02/2016, Microsoft and Avast downloaded and installed updates on the PC.  After the PC auto-redémarré as part of the Microsoft updates, I couldn't connect to the internet.  Connect to the network now says unidentified network - no network connection.  The adapter looks like to she always sees the (watch 100 Mbps) connection, but no data packet move.  Device Manager indicates that the unit is working normally.

  I ran through the resolution of the problems of Windows network. I checked the cable was attached, reset the home modem, reset the adapter (toggle), uninstalled/reinstalled using the latest adapter driver available.  I have disabled the Windows Firewall because Firewall Avast wouldn't start.  I disabled all the Avast settings to see if it eliminated the problem.  I tried to run the system restore before the updates but continue to spread the message that there was an unexplained error and restore failed.  All this was done in Normal mode. I restarted mode safe and had the same problems without success.

  I was able to clear the problem by manually uninstalling updates of security Windows which were loaded on 09/02/2016 through the programs and features Control Panel. Then I did the repair of Avast program operation.  I rebooted the computer and the internet connection worked. Then I reinstalled manually updates Windows security on the Windows Update program.

• Xbox 360 Media Center Extender loses the connection to the media center to Windows 7 after change of router

  I have a Windows 7 Media Center box, and an Xbox 360 that I use as an Extender.  The two connections to the same wired router.  Everything worked fine until I went on my old router (failed) and put in a WNDR4300.   After the new router has been installed, I didn't have the Extender work then, deleted from the media Center and re - he added.  It worked but after I shut off/started the xbox, no link.  It is repetitive: I can make a new connection, but then it didn't reconnect after reboot of the xbox.

  Check/change:

  -J' changed to a static IP xbox

  -There is no part 3 a / v or a firewall on the support center

  -L' on the media center network adapter is 'home '.

  -The network card on the media center * fact * show the xbox 360

  -The event log after the xbox is restarted shows:

  event ID 538: installation of media center extender does not like the Extender has been detected on the network, but for the Extender upnp search failed (timed out after 20000ms)

  -How long before it, I have found that the service IS running upnp device host (and set to auto)

  -J' checked 4300 router wndr and UPnP is enabled (advertising set to 30 minutes)

  question, any ideas what configuration will solve this problem?

  Hello

  I suggest to look and ask here:

  https://support.Xbox.com/en-us/browse/Xbox-360?XR=shellnav

  http://forums.Xbox.com/

  http://www.thegreenbutton.TV/forums/

  See you soon,.

  J

• How can I get rid of a 'sidebar' (an additional site without on the left of the screen) that is still there after restarting Firefox and even cold, start the computer?

  I opened a Web site of the library without specifying "in a new tab. I expected to crush the existing active tab. Instead, he opened in a demi-fenetre on the left, without tab and without all the icons "Min/Max/Close. I can not close it even by restarting Firefox or stop and start the computer. He now appears on each screen in Firefox with each tab. I note the address of the site to be replaced, but the offending site is https://servicing.capitalone.com/c1/login.aspx.

  There is an 'X' in the top right of the sidebar.
  You can replace it with a different sidebar; Therefore, you can use "Ctrl + B" to bring up the sidebar bookmarks, use "Ctrl + B" once more to turn it took off.

  Click on the star to bookmark to bring up the bookmark, in the lower left corner, if you see the following, uncheck the box.

  [X] load this bookmark in the sidebar.

  You can right click a bookmark to display the bookmark properties, uncheck the "load this bookmark in the sidebar".

  In the sidebar

  1. Right-click to bring up the Page Info
  2. Triple - click the url
  3. use "Ctrl + B" to bring up the Bookmarks Sidebar
  4. Paste the url in search, then right click on the found object to bring up the bookmark properties

  In the list of Favorites library there is unfortunately no column in the list of library of favorites for this feature, but you can click on the bookmark and properties will be displayed on the box under the same information, if you see a drop-down list "gone" click to view the list of properties.

  If you want to see the extent that you have these bookmarks you export our bookmarks in bookmarks.html file and then view the source and use of find for WEB_PANEL = "true" - I have the extension 'Search all', so I can see how many times the string occurs and where.

  It has a turbulent history, it is useful as a reference column, but it was destroyed in Firefox 3, after use in a link, use, restoration of use later but not keyworded bookmarks and not places links both where it makes sense to break. Remained at does not not for keywords because they wanted to destroy the mot-cle--Word key lost for a year in the beta version of Firefox 3. Now, it must be eliminated because few people (can) use it (properly), but they will make this inaccessible box first - someone ' else see the additional error with that.

• ERROR 7026: CONTINUATION OF THE DRIVER (S) FAILED TO LOAD AFTER RESTART

  The event viewer showed this error after startup for 2 or 3 days. The drivers listed are OMCI and NULL. I've been ignoring it causes web search seems to show OMCI is a cost of control tool for IT managers that has to do with the networks... I have only one computer.  My system performance is very good. I went to devices and updated all the drivers. Should I worry about this? I had to do cleans up registry, disk defragmentation, disc chk, associated clean disc trying to get rid of a virus... This error code showed some time ago and then stopped and now there back THANKS Pharmerbill

  Hello

  This issue may be caused if one of the device driver on your computer is faulty. This is probably due to the graphics card. You should try to reinstall the drivers adpter display in most of the cases it fixed the issue.

  See you soon.

• Deleted some files in the windows directory a few reasons, after restarting the system. showing a victim of COUNTERFEIT windows. How to reactivate my windows?

  Hi all

  I bought Lenovo laptop 10 months before staple. Today in my system, a malicious program "Progressive Protection system" is automatically installed. As a result, I searched the Internet and deleted some files in windows directory in C drive. Now after restarting the system, it's popping up a message stating "you are a victim of counterfeit windows. Even I have validated my window in internet with options available always is saying that my window is not genuine. Don't know how to turn it back on. If someone can help with this problem?

  I suspect that the problem is that the malware is still present - a repair installation will not get rid of it.

  @Prad_121

  Please follow the directions for the RDO and run the analysis offline so you can - at least, so we can be reasonably sure that the machine is free of malware.

  Once completed, please post a new report MGADiag.