Y510p clean install (software Lenovo)

Similar Questions

• Windows 10 utility clean install and lenovo

  I performed a clean installation of windows 10 (pro) on my y50, installed all the drivers, but the utility lenovo lenovo app provides for windows 10 does not start after installation.

  It is a very important application for me and without it I would probably restore windows 8.1 so any help is greatly appreciated.

  After some research, I found the installation that I needed.

  Source.

• IdeaPad y510p clean Windows 7 install - SSD not detected

  I bought a new Ideapad y510p just before Christmas and I wanted to do a clean install of Windows 7-64 bit.

  I created a USB startup device as required and put the drivers from lenovo on her page too.

  My problem is: after you delete the partitions, the installer of windows 7 do not recognize the SSD more...
  My BIOS is set with legacy of disabled secure boot support.

  Furthermore, when it came to load the drivers, it says no driver signed device not found.

  Someone has an idea of what's going on?

  Hi Clet,

  Since the serial number on this picture, you have the 59375625 model. After digging further, this parts search page and this point merchant does not seem an SSD on the specifications list. If the reception / box indicates that you have a 1 TB + 24 GB SSD, you may need to check under the hood (see pages 38-39 of the hardware maintenance manual)

  Link to photo

  Concerning

• Clean install of an installation of Lenovo. DVD: UEFI vs Legacy + installation according to Lenovo Thinkpad user Guide

  Machine: T520 purchased February 2012

  O.S. W ~ 7 Pro 64-bit

  I want to wipe the hard drive, buy a Lenovo W ~ 7 DVD installation of PRO and make a completely clean install.

  The user guide for Lenovo (.pdf), Ch. 8, Adv Config, installation Windows 7, p. 295 (298 212) said:

  Start the installation of Thinkpad, choose UEFI against Legacy, and then insert the installation DVD.

  This of course does not apply when the hard drive has already been erased (required to 100% remove all traces of damage caused by a virus, including the recovery partition (Q-drive).

  When an intallation DVD is purchased from Lenovo, is not the first step to insert the DVD? Then there is probably a resulting install wizard an O.S. restored?

  If this isn't the case, please tell me what are the surprises in store, and where I can find a reliable resource to consult written!

  Thank you.

  Hi, Z

  Sorry, but I'm not all-new advanced in the understanding of the apparent contradictions, or how to proceed.

  It is not the case in this case that the Lenovo User Guide is referring to one of several types of clean install, and that he has no idea the other methods?

  If my first step to reinstall the version of Lenovo's W ~ Pro 7 is to use a 3 rd-party app to remove completely all the files from the hard drive, how do I then perform any action before inserting a facility provided by Lenovo dvd? I know that the BIOS software is separated from Windows, but it's still there? Alternatively, is the User Guide of Lenovo referring to a situation in which a first is not a so-called "hard drive wiping" before to start a clean reinstall? In addition, if a wipe everything first or not, is the guide referring to an installation of Microsoft (generic) dvd and not wearing only not on a Lenovo purchase? I think that an installation DVD purchased from Lenovo back on my computer, exactly what was there before and ask me not to make decisions as the UEFI against Legacy (in fact, the words "UEFI" and "Legacy" are not yet in any computer on my computer profile file.

  On the other hand, if the L ~ the User Guide instructions apply in fact to a hard drive wiped, the Guide says absolutely nothing about what criteria to use to make this 'choice' between UEFI 64-bit and 64-bit legacy.

  (When the Lenovo user guide instructions raise more questions than the original question, then these instructions are worse than no instructions at all!)

• How to make El Capitan to recognize my Canon printer I've done what I think is everything: one clean install of El Capitan (another problem); Reinstall the software from the CD; Anon same impression reset. No luck at all.

  How do El Capitan to recognize my Canon printer? I did what I think, that's all I can: clean install of El Capitan (another problem); Reinstall the software of Canon from the CD; same impression reset - my printer shows not yet up! I tried LAN and USB.  No luck at all. The printer does not yet appear upward on the tree of USB in the reporting system.

  What printer model Canon...?

  kologano wrote:

  The printer does not yet appear upward on the tree of USB in the reporting system.

  This looks more like a bad USB cable or bad printer.

• Satellite P500 - 01 G-install the Toshiba software after clean install

  Hi all

  I have a Toshiba P500 - 01 G (http://www.mytoshiba.com.au/products/computers/satellite/p500/pspgsa-01g003/overview) running the grouped Windows 7 Home Premium 64-bit. I bought an upgrade to Windows 7 Ultimate, but can not use it, he just tells me to use Windows Anytime Upgrade.

  However, I can use it for a clean install and I intend, but I don't know what to do on the Toshiba Software (http://www.mytoshiba.com.au/support/computers/satellite/p500/pspgsa-01g003/download?os=25).
  I read on another thread that the software must be installed in a certain order and frankly I have no idea! I don't want to break something! I'm not to ask for the list accurate for each of them (except if you have time) but just a general guide as to what I should install in the order.

  Also, I guess that my recovery partition is erased in the process and I can't get it back. Is this true?

  Thank you very much. I really appreciate it,
  Abraham.

  Hello, Abraham

  I m the Satellite P500 owner too and it's really great machine, isn t it? I like it. My Toshiba best ever.
  My machine is preinstalled original Toshiba recovery image and it works without any problems so I put t want to change anything.

  Back to your question. I assume that you have a few reasons why you want to use the Ultimate version then you should try to clean OS install. Before you anything create recovery DVDs. Make two copies.
  After that make what you can do with your laptop all you used to because if you want to have the factory settings, again you can use created the recovery disc and install original recovery image.
  After recovery of registered OS image will help and you will not be able to start the installation of HARD drive recovery then please create restore DVD.

  Installing Win7? I have the European model, and I will send exact installation order list. There may be small differences compared to the model of the AU, but the principle remains the same.
  Here we go:
  Windows 7
  Chipset SW installation utility
  Intel Management Engine Interface
  Display driver
  Intel Turbo Boost Technology driver
  Intel Rapid Storage Technology driver
  TOSHIBA supervisor password utility
  TOSHIBA HW utility
  TOSHIBA Value Added Package
  O2 card reader controller
  NVIDIA driver HD Audio
  Conexant Audio driver
  Wireless LAN driver
  Synaptics Touch Pad Driver
  TOSHIBA HDD Protection
  Bluetooth Stack for Windows by Toshiba
  LAN driver
  Winbond CIR driver
  YUAN pilot DVB-T/ATSC Tuner
  Sleep USB TOSHIBA and service charges
  TOSHIBA face recognition
  TOSHIBA eco Utility
  TOSHIBA HDD/SSD Alert
  TOSHIBA Service Station
  HDMI Control Manager
  TOSHIBA Remote Control Manager
  TOSHIBA fingerprint utility
  PatchFiles FixFPService_REG_1.0
  ConfigFree
  TOSHIBA Assist
  TOSHIBA Web Camera Application
  TOSHIBA Extended Tiles for Windows Mobility Center
  TOSHIBA Network Device ID registry tool
  PatchFiles PCIIDEREG - 1.1

  I hope this will help you.

  Good luck and if you have any other questions please let us know.

• Not able to install the HP software after a clean install of win7, hpbi and harddisk.dll error

  Hello

  I bought a tm2 with win7 home x 64, my IT guy at the office have installed win7 ultimate x 64 and of course all the HP software was missing when I returned. Fortunately, they recorded the old files and I was able to locate the SwSetup folder and managed to install essential drivers.

  However, I miss all the HP software, which means that I can no longer find it not in the SwSetup folder or it will not be installed. I found the HP Touch Smart 'something' Center (folderHPTSLC) but I get the error "hp\bin\hpbi" and I found the Recovery Manager win7 HP homepage, but I get the error "hardDisk.dll.

  I am really a bit upset that I have to spend so much time to solve a simple problem, I have an intact recovery partition, a partition HP tools intact as well as all the files in the SwSetup folder, how can it be difficult?

  I want the software I paid and so far, I spent several hours looking for a solution to a seemingly simple problem (just provide the software on your hp, or at least one that reinstalls the Sw from the hard drive to the HP computer if you fear that your software may be used on other HP computers...).

  Can someone please provide me with is the solution to the problems mentioned above, a link to the HP Touch Center application work (although I have the files, he just moved there) or tell me how I can restart the installation of the HP software and driver that happens just after you have configured your win7?

  Thank you

  Geen

  I agree, our IT screwed up guy, they didn't even know the upgrade thing... :-/

  In any case, I found a way to install the software I was looking for, just unzip to a folder and run the .msi file in the src folder.

  Even if not all the applications had such a record, most of 'em had.

  After playing with the sw a bit, I realized that I didn't like it anyway, boy I'm glad, I wasn't going to come home!

  and btw, we bought a HP Mini and it was a nice little software, called AppInstl in his swsetup, actually just the sw file I was looking for. Of course the same thing happened with the Mini ('clean' installation), but with this app, that I managed to re - install all the sw I wanted without any problem, except QuickWeb, of course, but that seems to be a general problem.

  Seems to me that HP has also seen the need for a "easy install your software after clean install" app.  :-)

  Thanks for all your comments, my problem was solved!

  Rgds,

  Geen

• Can I do a clean install of Windows 8 (without the DELL OEM software)?

  Hi people,

  I just bought a DELL Inspiron 17R laptop computer which came with Windows 8. I want to install an aftermarket SSD and do a clean install of Windows 8 on the SSD without all the stuff extra DELL piles on the computer in their factory. However, the laptop does not come with any media of Windows 8. My other options (copy windows divide in the SSD or use Windows backup and restore), both result in installing Windows 8 with a lot of software DELL.

  DELL said that they do not have the installation of Windows 8 media and I need to contact Microsoft to get it. Any ideas on how I can go about this? I'm happy to pay a nominal fee for the discs, but having already an OEM of Windows 8 installation, I want to avoid going to the shops and buy a new license.

  Any ideas are much appreciated.

  Kind regards

  Chris

  Unfortunately, your only option is to create a disk backup and restore using recovery tools provided by Dell and use it to reinstall Windows 8. This is especially true because you run Windows 8, which are not available elsewhere.

  or

  SSD of cloning:

  You can clone the installation for the SSD, provided that the SSD is large enough to accommodate the installation to be cloned.

  See

  http://www.ssdfreaks.com/content/664/how-to-clone-HDD-to-SSD-with-Windows-7s-own-software or (easier) use a copy of the trial of Acronis True Image Home.

  Note that, immediately after cloning, you must stop and unplug the original installation. The disc can be reconnected once the DSS started successfully.

• Lenovo Ideapad 100 s-14IBR Windows 10 clean install

  I have problems to do a clean install of Windows 10 on my Lenovo Ideapad 100 s-14IBR and need assistance expertise.

  BIOS settings

  Secure Boot: disabled

  The boot priority: Legacy Support

  Boot Priority: First Legacy

  Boot USB: enabled

  -Boot from USB with Windows 10 iso created with Rufus - "for UEFi GPT partition scheme.

  -Windows Installer appears fine, when I choose 'Install now' I'm coming to the "Where do you want to install windows?" and get the low error message that prevents me from going to the.

  Error: "Windows cannot be installed to this disk.  This computer's hardware may not support booting to this disk.  Make sure that the drive controller is enabled in the computer's BIOS menu.

  Info drive is drive 0 space unallocated - I deleted all the partitions-i tried formatting/deletion/creation of new partitions with no success.

  Any help will be greatly appricated!

  I solved the problem!

  When I created the bootable USB key with Rufus, I chose 'NTFS' as the 'file system '.  You must choose 'FAT32' as the 'file system' and make sure CNE 'scheme and taret system partition type' 'GPT for UEFI partition scheme.

  After that, the installation worked flawlessly!

• If I do a clean install, I have to reinstall all my software

  Hello!

  Filipe my name is

  I have a MacBook Pro 2010, which is compatible to install the Mac OS Sierra

  It is very slow and I would like to do a clean install of the operating system new

  I know that I have to do a full backup of all my data - photos, emails, documents,... - but if I take the decision of the new facility, I have to reinstall all my applications, programs,... - as Office for Mac,...?

  Thanks for your response!

  Only, or restore from backup.

  (144882)

• How to get the software HP Coolsense works again after the clean install (win7)?

  I recently purchased a DV7 6014TX and upgraded to an SSD and a clean install of the retail version of windows 7 64-bit. I want to know how do HP Coolsense works again? I saved the folder drivers of my original hard drive SW and I so all people. SP52814, I downloaded the installer coolsense, but it doesn't seem to work. Any input on this would be highly appreciated.

  Coolsense also requires HP Support Assistant see links below

  HP Notebook PC - on CoolSense technology

  Download

  HP Support Assistant

• Pavilion 14 G6S71UA #ABA: I'll always be able to use the pre-loaded software HP products if I do a clean install of Windows 10?

  I have a laptop 14 flag that came with Windows 8.1 - 64 Home, and I have upgraded to Windows Home 10-64. The upgrade went very wrong, but I would use Win 10 if possible. Microsoft recommends that I have to do a clean install of Windows 10, which will require you to reinstall all my programs MANY. They cannot tell me, however, if I'll still be able to use some of the applications delivered HP pre-loaded on my machine and that I find very useful - even if I am out of warranty. For example, I use HP Support Assistant updates the driver, and I found that HP DriveGuard works really well!

  I'll always be able to download all of these products and hence? I'll be able to get them on the page of the drivers for my laptop? If I can't, I'll probably have to settle for return to Windows 8.1.

  Thank you.

  Because the rep on the Microsoft forum did not answer my questions, today I called the support of Microsoft Windows 10 phone number. After that the rep is lost another hour of time my (and their) me browsing to enter SafeMode via several methods, everything I told him that I had already tried. the representative suggested that customizations of account that I had applied could be the cause of the distress.

  She also informed me that, for security reasons, Windows 10 no longer allows connectivity Mode Wireless safe; Although, if your PC is physically connected to the modem/router, you should be able to enter in IE (and maybe even in Edge) in Safe Mode.

  So I added a new local administrator account (that said, I log in with a password and not with one account Microsoft.), to be used only for safe mode and left all its parameters to the default values for Microsoft. And it worked! When connected to my router, I could get in Mode safe mode with internet connectivity via IE! Thanks to this rep, I finally have success.

• 7. clean install

  Hi all

  I have a Thinkpad R500 2732 - 32G with Vista Business 32.
  I would like to upgrade to two things: a SSD drive so I don't have to worry about the shocks on my hard drive at all (I'm pretty freaked out when there might even be the slightest possibility that this happens right now).
  But for this I must also move to Windows 7 for better support than Vista for these readers.

  The plan is Windows 7 Professional 64-bit.

  My question is this: if I install the two updates, will all run on 64-bit, I want to say the software Lenovo has preinstalled right now.

  And is it possible to make a dvd like I did for Vista that contains an installation full of every driver and every piece of software you can do a complete reinstallation in a few hours?

  Yes, Lenovo also provides x 64 drivers for Windows 7. Please find the appropriate Support Page or ThinkVantage System Update drivers to automate the installation process.

  Please note that you can do an upgrade from a 32-bit of Windows Vista installation to a 64-bit Windows 7 OS and vice versa. You will need to do a clean install and then manually install the drivers (above)

  You can create an image backup of your system with 3 third-party backup software or ThinkVantage Rescue and Recovery (I recommend it) when it has all the drivers, and which correspond to your needs.

• My macbook air 13 "(2015) is very slow, even after a clean install"

  Hello

  I have a macbook air 13 "from 2015 and it is VERY slow. I did a clean install from scratch of El Capitan (10.11.06) and always very slow.

  Etrecheck give ' "Performance: poor"»

  Is there a hardware problem? or what to do?

  Thank you

  EtreCheck version: 3.0.6 (315)

  Report generated 2016-10-05 10:18:11

  Download EtreCheck from https://etrecheck.com

  Duration 17:11

  Performance: poor

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Problem: Computer is too slow

  Description:

  too slow

  Hardware Information: ⓘ

  MacBook Air (13 inch, early 2015)

  [Data sheet] - [User Guide] - [warranty & Service]

  MacBook Air - model: MacBookAir7, 2

  1 1.6 GHz Intel Core i5 CPU: 2 strands

  8 GB RAM not extensible

  BANK 0/DIMM0

  OK 4 GB DDR3 1600 MHz

  BANK 1/DIMM0

  OK 4 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: en0: 802.11 a/b/g/n/ac

  Battery: Health = Normal - Cycle count = 40

  Video information: ⓘ

  Intel HD 6000 graphics card

  Color LCD 1440 x 900

  Software: ⓘ

  OS X El Capitan 10.11.6 (15-1004) - since startup time: less than an hour

  Disc information: ⓘ

  SM0128G SSD APPLE disk0: (121,33 GB) (Solid State - TRIM: Yes)

  EFI (disk0s1) < not mounted >: 210 MB

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  Macintosh HD (disk 1) / [Startup]: 120,10 (Go 104.05 free)

  Storage of carrots: disk0s2 120.47 GB Online

  USB information: ⓘ

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Guardian: ⓘ

  Mac App Store and identified developers

  Launch system officers: ⓘ

  [no charge] 6 tasks Apple

  tasks of Apple 166 [loading]

  [running] Apple 58 jobs

  [killed] 9 tasks of Apple

  9 killed process lack of RAM

  Launch system demons: ⓘ

  [no charge] 47 Apple jobs

  [loading] 158 jobs Apple

  [running] Apple 77 jobs

  [killed] 8 tasks of Apple

  8 killed process lack of RAM

  Launch demons: ⓘ

  [loading] com.macpaw.CleanMyMac3.Agent.plist (2016-10-04) [Support]

  User launch officers: ⓘ

  [loading] com.bittorrent.uTorrent.plist (2016-10-04)

  [loading] com.macpaw.CleanMyMac3.Scheduler.plist (2016-10-05)

  Items in user login: ⓘ

  iTunesHelper program (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)

  uTorrent program (/ Applications/uTorrent.app)

  CleanMyMac 3 Menu program (/ Applications/CleanMyMac 3.app/Contents/MacOS/CleanMyMac 3 Menu.app)

  Plug-ins Internet: ⓘ

  Default browser: 601 - SDK 10.11 (2016-09-03)

  QuickTime Plugin: 7.7.3 (2016-07-09)

  3rd party preference panes: ⓘ

  None

  Time Machine: ⓘ

  Time Machine not configured!

  Top of page process CPU: ⓘ

  14% WindowServer

  4% kernel_task

  0% SystemUIServer

  0% cloudpaird

  Top of page process of memory: ⓘ

  670 MB kernel_task

  Mdworker (11) 188 MB

  Com.apple.CommerceKit.TransactionService (2) 41 MB

  Finder 41 MB

  Mds_stores 33 MB

  Virtual memory information: ⓘ

  5.02 GB of free RAM

  2.98 used GB RAM (1.82 GB being cached)

  40 MB used Swap

  Diagnostic information: ⓘ

  5 October 2016, 09:38:39 test - passed

  Hello, have you tried to reset the management system (SCM) controller on your Mac - Apple Support?

• Synchronization problems with the clean install

  Hello.

  Is it possible to push the content of my iPhone to my computer? (and not the other way around)

  Recently, I did a clean install on my Mac Pro and trying to get everything in working order. I got a load of music and voice notes on my iPhone that I don't want to lose, but the only way iTunes will allow me to manage the content of my phone is erasing all the content on my phone to sync to the 'new' library

  Help, please!

  Thank you

  A new installation of the operating system shouldn't have deleted personal data files unless you want to say that you have done more than a "clean install". You do not install the data files.  Looks like that erase you the iTunes library file and it was a big mistake because it is towards this specific copy of the file iTunes Library.itl that tries to sync your phone.

  Your i-device was not designed for unique storage of your media. It is not that a transfer backup device and media has been planned with you keep a master copy of your media on a computer that is in itself independently supported against loss.  To use a device with a different configuration, you pass the old library from a computer or a backup directly in the new configuration, not the device to the library. Synchronization of media isn't a way, computer device, update the contents of the device to the content on the computer, update or restore the content on a computer from a device. The exception is media to iTunes Store purchases that can be transferred to a computer.

  Re-download or transfer your purchases iTunes Store for the iPhone, iPad or iPod to computer - https://support.apple.com/HT201267 - 'this feature only works for content purchased from the iTunes Store. From iOS9 is more apps that now need to be re-downloaded directly from the store.

  To transfer other items from an i-device to a computer, you will need to use third-party commercial software.  See this document in turingtest2: recover your iTunes library from your iPod or device iOS - https://discussions.apple.com/docs/DOC-3991 even this method can fully recover what you originally had in the library. For example, in order to save space during synchronization if you had converted music files at a lower rate, or photos at a lower resolution, it is these lower quality files that will pick you up.

  If you subscribe to the Apple music, titles that are not part of the content that you have purchased or downloaded may not be transferred and must be downloaded directly from iCloud.

  To see other items: import photos and videos from your iPhone, iPad, or iPod touch - https://support.apple.com/HT201302 - are those you have taken yourself.