Z5 double low volume and vibration sound power

Similar Questions

• HP G71-340US low volume when audio sound on the highest rate

  Very low volume with sound levels at the highest point, intermittent reception during audio streaming, loud buzz unknown sometimes for unknown causes. I own a hp G71-340US since 4/10... and am these audio problems.  Y at - it an update to fix this problem?

  Hi Sharopa

  Try reinstalling the audio driver...

  Follow these steps:

  1. click on start and then type devmgmt.msc in the start search box and press on enter.
  2. from the list of devices, expand sound, video and game controllers.
  3. right click on the sound card, and then click on uninstall.
  4 restart the computer.

  After restarting the computer, sound card get installed automatically.

  If the problem persists, please upldate the audio driver following the steps mentioned below.

  Install an updated audio driver

• speaker shows on bar but no volume control and no sound

  the President shows, but no control of volume and no sound

  Hello

  ·        The audio device was working fine earlier?

  Check if Device Manager the device works very well. To open the device manager follow the link below.

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  First run the troubleshooter audio play, to run the same follow the link below.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-playing-audio-Troubleshooter

  If this does not help follow them the links given below to troubleshoot the sound.

  No sound in Windows

  http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-sound-problems

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Practical measurement "sound and Vibration Assistant.

  Hallo,

  ICH möchte eine Maschine von Gerauschemissionen untersuchen. Dazu soll mit Hilfe der Norm DIN EN ISO 11201 der emissions-Schalldruckpegel altitute werden. ALS Messhard-und software are mir following components available:

  Software:

  -LabVIEW 2010
  -Noise and Vibration Assistant 2010
  -Windows 7

  Material:
  -NI 9234 Messsystem mit NI USB-9162
  Condenser-Mikrofon
  -Laptop

  ICH möchte mit dem 'Sound and Vibration Assistant' ein Oktavspektrum bzw. Ein 1/3 - Oktavspektrum-> Terzspektrum aufnehmen. Dazu sind mir ein paar aufgekommen questions.

  -Laut Norm is die Messdauer bei measurements in 30s Oktav-Terzbandern fur Frequenzbander mit Mittenfrequenzen von 160 Hz low sowie für die 15s und Frequenzbander mit Mittenfrequenzen von 200 Hz und high.

  • Wenn ich alglemein eine measurement starte andert sich jede Sekunde bei einer sampling frequency von 51, 2 k und den zu lesenden 51, 2K das all Spektrum von samples. Also jede Sekunde ein neues result. Wenn ich also 30 Sekunden mass, means are dann, dass ich aus 30 results (Pro result ein entire Terzspektrum) den Mittelwert bilden kann bzw. muss?
  
  
  • Wie ich dann die unterschiedlichen Aufnahmedauer auf die Frequenzbander anwenden should? Should ich die highest frequency und niedrigste frequency q und dann der Zeit messen vorgegebenen correspondingly?

  -Laut Norm should as jedes Frequenzband eine Pegeldifferenz von mind. 10db zum Umgebungsgerausch available breast.

  • Also ich z.B. das Hintergundgerausch über 30 Sekunden mass. Dann jedes Frequenzband über 30 Mittelwert den Werten as image. DAS same mache ich dann bei Betrieb der Maschine. Kann ich dann die dB values direkt miteinander comparisons sprich Gabriel bilden die um zu sehen, ob die Pegeldifferenz 10dB kleiner oder grosser ist oder muss ich eine Logarithmische Pegelsubtraktion paper? nach der Formel section = 10 * lg(10^0,1*L1-10^0,1*L2) z.B.?

  -Wenn ich den aquivalenten Dauerschallpegel Leq messen möchte, die Die Formel Gesamtmessdauer wo mit einfliesst, wird dann der Mittelungspegel über eine Sekunde bei einer sampling frequency von 51, 2 k und den zu lesenden samples von 51, 2 K berechnet oder ist das result über die ganze Messzeit (wieder 30 Sekunden z.B.) berechnet worden? Oder ich aus den werten eine weitere Mittelung paper individual should?

  Viele Grüße

  Hallo Voyage200,

  Wenn ich alglemein eine measurement starte andert sich jede Sekunde bei einer sampling frequency von 51, 2 k und den zu lesenden 51, 2K das all Spektrum von samples. Also jede Sekunde ein neues result. Wenn ich also 30 Sekunden mass, means are dann, dass ich aus 30 results (Pro result ein entire Terzspektrum) den Mittelwert bilden kann bzw. muss?

  -> Should der Arbeitsspeicher gross genug breast ware are ermöglichen das auch Signal 30 Sekunden gepuffert mit dem mittelfristig-Verbraucher-Entwurfsmuster appears und die exported analysis often.

  Wie ich dann die unterschiedlichen Aufnahmedauer auf die Frequenzbander anwenden should? Should ich die highest frequency und niedrigste frequency q und dann der Zeit messen vorgegebenen correspondingly?

  -->--> Als Tipp Ja am examples of Anfang arbeiten mit den einfachen und Express VI. Powerful exported Programmieren mit den Low Level VI.

  I hope sharp Antworten helfen Ihnen weiter

  und verbleibe mit thank wurde

  Lorenz Casper

• Purchase / upgrade of LabVIEW with more Sound and Vibration

  Hi, supporters OR Forums,

  I'm new in LabVIEW but I'm working on a project that needs to use LabVIEW in these toolkits: DAQmx, PID and then Sound and Vibration Control.

  In order to experience on the vibrations, I need to use screws of Suite Sound and Vibration, which was not purchased in my Institute. We had the license for LabVIEW 2009 SP1. Unfortunately, I have a VI file written in LabVIEW 2010 my partner. According to the records of view VI, there is a lack of following screws:

  -SVFA Power Spectrum.vi
  -Application Directory.vi
  -SVT FFT .vi spectrum (Mag-Phase)
  -Frequency response (Mag Phase) .vi SVT
  -SVFA amplitude and Phase Real and Imaginary.vi
  -SVL get spectrum subset.vi
  -SVT UFFT58 write.vi
  -SVT UFFT58 write record 6 vi
  -SVT HFFT58 close file.vi

  I would like to confirm if these screws are supplied in the detroit and Viration Suite or / and other toolkits. If all of them can be found in the following Sound and Vibration, what I have to do is to buy the offer away from NOR, is it not? How much should I pay for this Suite.

  On the other hand, if we upgrade from LabVIEW 2011 (which is said to be able to deal with better timer - for the function of data acquisition), how much in total so also buy us more Sound and Vibration 2011.

  In comparison, which of the above two options is preferable in terms of price.

  For your information, I am working on my thesis at University in this means we would like to have a university degree.

  Plesea give me ideas on this subject. I'm sorry if my post is not fit to be posted here but I sent 2 emails to NI Germany (1 for the customer on the Web page Service NOR) and 1 in the Sales Department, but there is no response after more than 3 weeks.

  Thank you very much.

  Kind regards.

  Thinh Vo

  Hi thinhvo,

  All of these VI are included in the Suite Sound and Vibration, which means it's the only additional package that you would need to buy.  On the site OR in the States, the Sound and Vibration Measurement Suite USD $4119 costs.  Since I'm an applications engineer, I'm not in a position where I can advise you on the price, and I am sorry to say that it will be easier for you to contact your engineers in sales in Germany (I guess you are in Germany).  You may have better luck calling into lines of support rather than by e-mail.

  Thank you

  Lisa

• Windows XP my sound recorder audio device is a DODEC Audio USB, the volume and advanced is grayed, how do he turned the back?

  I just installed a turntable to record albums. I installed everything simply by following the instructions. The volume of the sounds and advanced recorder is grey and everything I do doesn't change it. Can someone help me?

  Hello

  You can view these methods:
  Method 1

  Download & install the previous version of the drivers for the sound card and check if it solves this problem.

  1. type devmgmt.msc in the search box start and press ENTER.

  2. in Device Manager, expand the audio drivers listed in the list of devices.

  3. right click on the audio driver > click Surdesinstaller.

  4 restart the computer and install the downloaded software.

  Method 2
  
  In addition, if you use a recording program, update or reinstall the program registration.

  Method 3:

  Please follow these steps to enable the "Windows Audio" service:

  1. Open the control panel of Windows XP by (depends on your settings in Windows):
     By clicking on "start > settings > Control Panel.
     By clicking on "start > Control Panel.
  2. Open the "Administrative Tools" Panel by (depends on your settings in Windows):
     Double-click the control panel 'administrative tools '.
     Click on "Performance and Maintenance" and then "Administrative Tools".
  3. Go to 'Services' Control Panel by double-clicking it.
  4. Locate the "Windows Audio" service.
  5. Check the "Status" column to see if it is disabled.
  6. If it is disabled, click with the right button on the "Windows Audio" service and choose "Properties".
  7. On the general tab, change it "Startup Type:" drop-down on "manual".
  8. Restart your computer.
  9. Follow steps 1-6 to open the properties of the Audio service 'Windows'.
  10. Click on the 'Start' button to activate the Audio service 'Windows'.
  11. You will now be able to change the control panel 'sounds and Audio devices '.

• The HT820 ear and lower volume stuck button

  I had these headphones for almost 2 years works very well. I don't have a bluetooth phone, but I use my HT820 with my HP Ipaq 211 listening to music or watching movies. I also connected them to my work and the home pc. At work I connected them to the phone Nortel 1150. I just had a few problems since I got to the two atria are beginning to tear. I had them in my backpack and I don't know how, but one ear cushion came off the coast. So I'm wondering where I could get replacement tips? The other problem I have is with the low volume on the left hand button. The button is stuck, but I can live with that, because it is just the right volume level. If I don't find any guesswork replacement I can buy another pair and I can leave the old one at work since I can use it with the 1150 of Nortel. Thank you

  Join this other thread:

  As for the volume key. This aspect will likely be repaired if the warranty is only for one year. Sorry!

  Mark

  Support Forums Manager

• Difference between signal y express sound and Vibration Assistant

  Buenas,

  Cuando instalas el of sound and vibration luego software, tienes back ejecutables: Sound and vibration assistant y signal on purpose. Los abres los back if you lo lo mismo. Mid questions are:

  • What difference between hay?
  
  
  • Da igual use uno u otro
  
  
  • If desinstalo uno los pasa algo back?

  MUCHAS gracias

  Saludos

  Hola, aaramburu,

  in lenguaje andar por casa, Signal Express are el programa matriz y S & VA el are UN modulo what instala encima y reviews una paleta Programación than permite usar funcionalidades specific sonido Análisis y constant. El Signal Express has leaves, apply filters, a configurable software para datos closing, etc. If el S & VA mallards are mallards nuevas funcionalidades enable use tarjetas para señales dinamicas o DSAS that enable leer of tacometros, acelerometros, hacer análisis octavas, etc.. ES como if instalas LabVIEW, are UN lenguaje general Programación y quieres una camara use. Sober el propio LabVIEW has instalar Modulo de Vision para el LabVIEW y is anaden kbes imagen aforementioned funcionalidades.

  No nada desinstales, one extended capabilities. As has using uno u otro, depends on the nature of the application as desarrolles. If going to a Signal Express y seleccionas help > Getting Started with > Getting Started with LabVIEW Signal Express Fiesta el tutorial Básico para el manejo del entorno con guiados exercise. Leads unas cuatro horas. If you want to develop una application of sonido y vibration, using a high port tal y como is muestra in el tutorial help > Getting Started with > Assistant Sound and Vibration.

  I hope this information you follows from utility.

  Jesus.

• How can I integrate IPS into the Sound and Vibration Assistant 6.0?

  I found out how integrate time domain signals to m/s in S & V 6.0 Wizard, but not IPS.  I could scale the signal, but the axis labels will be wrong.  How can I integrate directly to the IPS of the entrance of G?  Also, is there a way to do the same thing for the analysis of frequency domain?

  In the audio wizard and vibration - step vibration level, use

  on the integration tab - select double integration and click export integrated signal

  Now you have a shift of signals in the right units.  Make a spectrum on that and you get a spectrum of integrated signal.

• The NI9423 will work with Sound and Vibration VI

  Will be that the NI 9423 mounted on a chassis cRIO work with the NO audio and vibration of VI?

  I have an optical encoder of 10-30 V 100 pulses/revolution and would like to make angle field order analysis with her.

  is the NI9423 a card appropriate for this purpose or is something else better suited, I'm open to change the type of encoder if necessary.

  Hi Bodger

  How fast do you think the tree to turn to? The speed of switching module is able to pass to the 1uS extremely quickly. This means that you should be fine unless you are turning the tree at a ridiculously fast speed of approximately 600000 RPM.

  Regarding the reading of signals with the sound and vibration screw, you should be able to do this using the digital tachometer functions.

  Thank you very much

  Dan.H

  NIUK Applications Engineering

• Construction of the installer wants to sound and Vibration Distribution but my vi do not need

  My vi contains some common entries and a regular to read some 4-20mA, see attached data acquisition.

  So I save a new project and build an exe with the vi, no problem, see project files attached.

  

  Then I start building the Setup program by clicking below to install the libraries. I think that I click on the right side of the law library?

  

  

  But lo! OR say I need sound and Vibration Distribution, now, where does? My vi has no sound and vibration functions...

  

  I click on no, the installer don't build Labview.

  I click Yes, Labview kept asking me where is the audio library and vibration.

  

  I bought a NI Developer suite, expensive things like costs about US$ 4000 +. My software vendor told me that I don't have the license for the sound and Vibration Distribution.
  So, what should I do? Clicked on some bad settings during the generation of the installer? Is there a way around this problem? Thanks in advance!

  Hey,.

  Try to repair or uninstall/reinstall your DAQmx driver as described in the following KB: http://digital.ni.com/public.nsf/allkb/8C37AB992EB29EA7862571680056E78A?OpenDocument

  Christian

• More Sound and Vibration - Leq measurement?

  Hello

  I'm new to following Sound and Vibration and can't seem to find how to measure Leq. To clarify, I do not have LabView with this package, just the Sagno & Suite 2010. Currently, the only options are linear, exponential, maximum and equal trust (all found in the analysis of Octave SPL stage).

  Should I have LabView to perform a running Leq or Leq measurement?

  Hello

  Examines the LEQ under analysis. Take a look at the following screenshot.

  

  I would like to know if this isn't what you're looking for.

  Eric

• sound and Vibration Assistant. Speaker output

  I am new to the sound and Vibration Assistant and he had to get monitored sound of a surfboard 4722 the speaker to computers.  I can capture data and display it, but I want, but can't seem to find a way to get the sound to the speakers.  Thanks for any help

  Hi Mike.

  Unfortunately, the Sound and Vibration Assistant doesn't have a built-in way to route your signal input to your speakers.

  However, if you have LabVIEW, you can add a step to run a LabVIEW VI that generates output a file from your computer speakers (or external speakers).  You must write a LabVIEW program that either acquires a signal or load a file of recorded signal, then this signal to your speakers.  "You will most likely use the Play Waveform Express VI of the Express" exit pallet on the block diagram.  "After you wrote this program, you need to add a step in the sound and Vibration Assistant using the Add a step" run a LabVIEW VI.

  I hope this helps.  Good luck with your application!

• my sound works fine except when I play a video. When I click on the volume, then mix it bumps on speakers and system sounds, but not when you set windows media player

  When I imported my videos from my phone and then began to look at there was no noise. I clicked on the volume, and mix. adjusting the volume on the speakers and his system, it's a ding, but when I have not adjusted the volume on windows support no ding. It is not cut.

  Hello

  What version of Windows are you using?

  This is by design, when you try to adjust the bar its windows media player or WMP or the volume mixer you will not hear the sound of ding.

• How to cancel the keyboard sounds and vibrations on an Acer Iconia A1 - 840 8 inch tablet

  Keyboard continues with the audio and vibration all in settings | Sounds | Tactile sound and vibrate on touch are unchecked.  It is particularly strong for the Google Chrome browser.

  Settings/language & entrance

  on the right side of the keyboard that you use, there is an icon that will open some keyboard settings, tap that

  Uncheck the box

  Vibrate on keypress

  Sound on keypress