10 Windows installed cannot see my drive OSX

Similar Questions

• How is it, windows XP or Windows 7 cannot see network drive?

  first of all, I have 5 computers.  Installed with Windows 7 installed with Vista and 1 2 3 MacBook Pro.  I created 1 network drive to more easily move files named "ShareMe.  All the protable can use the shared folder since I gave permission to everyone.  All the computer can use the network printer.  I installed Windows 7 on a Mac using VMware 2.0.5 and able to print using printer network with no problems.  I installed another Windows 7 on VMware Workstatin on a PC, and it can use the network also printer without any problems.

  (Everything is legitimate and so far I just was not updated to 2.0.6 because I heard a lot of things to have a slow speed)

  That is the problem, not an operating system that runs on VMware can't see my shared folder in the network, it cannot see networked host computer.   I speak not shared folder between VMware and the computer host.  Between the host and VMware are very well; However, I'm talking about that all shared folder the computer can see (folder ShareMe).

  All in the same workgroup

  Using NAT to network adapter

  Tota1 wrote:

  Using NAT to network adapter

  This is the problem because it puts the virtual machine on a separate subnet, then the one on the host is.  Past to open and release/renew IP on each virtual Machine.

  Take a look at: Understanding Networking in VMware Fusion

  Tip: With a Machine virtual Windows switch between NAT and connected by a bridge or visa versa, can be made without restarting, or even by using ipconfig to release/renew the IP address.  Simply toggle the State connected/disconnected from the network of the <...>Network icon on the status bar from the type of network between the two. It takes but a few seconds and a few clicks and is faster and easier the alternative methods.

• Win 7 install cannot see hard drive

  My office has a dual boot with two RAID 0 configuration bays (2 x 40 GB SSD Corsair and 2 x 230 GB Seagate Barracuda) with Windows 7 Home Premium 64 bit on each table. I wanted to convert the largest to a standard IDE configuration with a clean install of Windows 7. I disconnected one of the 230 disc gig and put the other 230 as an IDE drive in the Intel Storage Manager. Now, it appears in the BIOS and I can see as a D: drive in Windows, but Windows 7 install do not.

  With most large raid so disabled both Windows 7 boot choice appeared again during the boot, but of course that one can load. I tried to fix things with msconfig, which showed the two BONES, and I removed the disabled. But Windows 7 install again does not see the drive of 230 gig. (It's the disk Win 7 Upgrade btw)

  How can I resolve this installation issue?

  (1) you remove the existing partition and reformat the hard drive before installing Windows 7 on it? If this is not the case, do.

  (2) also the 230 GB drive must be connected to a standard SATA (Non RAID) port before installing Windows.

  What drives when using two pairs as RAID configurations has the "System" partition, it was the SSD drives or disks Seagate 2 x 230. I guess the system partition is on the SSD you can still start Windows with only the connected Yes SSD?  If Yes, then the steps 1 & 2 above are still valid.

  J W Stuart: http://www.pagestart.com

• Re: Satellite A200-209 - Windows 7 cannot see DVD drive

  Hey

  Ive reinstalled my (new) PC from Windows 7 to Windows 7 and some time after I had this problem.

  My DVD drive is "unseenable" of Windows and it can not read any disks.

  I think its something about the drivers, but I can't find a driver for DVD: P

  THX.

  Optical disc drive is listed as unknown device in Device Manager?

• Windows 7 cannot see is not my SCSI disks when I try to install. As the IDE drive is showen but is not usable.

  Windows 7 cannot see is not my SCSI disks when I try to install. As the IDE drive is showen but is not usable. Is there a FDISK program that can be run to solve this problem from a command promt?

  Hello

  You try to access BIOS and change the SCSI to IDE in the BIOS or Raid in IDE and try to install Windows 7.

  If it fails, contact your SCSI manufacturer for the latest drivers for your SCSI and install it by clicking on load drivers and try to install Windows 7.

  Hope this helps and works.

  Chris

• I can not eject a dvd from my drive iPhoto super-cannot see the drive open up Adobe Photo Elements and organizer and then apps get hung up "not responding" and cannot do anything - I've fixed dozens of times w msg success drive.  Help

  I can not eject a dvd from my drive iPhoto super-cannot see the drive open up Adobe Photo Elements and organizer and then apps get hung up "not responding" and cannot do anything - I've fixed dozens of times w msg success drive.  Help, please.  Thank you!

  Hello golden2,.

  I understand that you have a DVD picture in your SuperDrive drive, but it is not mount on the desktop and will not eject.

  Please, try the procedure described in this article using the disc is ejected.

  Get help with the SuperDrive slot on your Mac - Apple Support loading

  Do not eject discs or discs eject slowly

  1. If the drive ejects discs slowly or appears to have difficulty, insert and eject a disc several times. Check the disc to see if it has a label or other material stuck to the disc which increases the thickness. Remove the label if possible.
  2. If the disc does not eject, try pressing the eject on the keyboard button. Some older keyboards may use the F12 key to eject the disc.
  3. If the disc does not eject, try dragging the icon of the disk to the trash.
  4. If the disc will still not eject, try to hold down the mouse or trackpad button after you restart the computer. The Superdrive should attempt to eject the disc.
  5. If the disc still does not eject, reset the System Management Controller (SMC) and repeat steps 1 to 4.
  6. If the disc still does not eject, Contact Apple or an provider of services authorized Apple, or make an appointment with a Store Apple Store for further assistance.

  Take care.

• I get the error code 1706 - valid no source is found for the product my Hub. Windows install cannot continue.

  I get a pop up saying error 1706 that valid no source is not found for the product my hub. Windows install cannot continue.  Also "the feature you are trying to use is on a nework resourse which is not available."

  Can someone tell me what to do and what is the problem

  Thank you

  Hi Traceyjane,

  (1) when exactly it happens?

  (2) do you use the computer as an administrator?

  (3) what is the number of brand and model of your terminal?

  If you try to install the software for your hub, make sure that you install the correct package for your computer.

  Step 1: Try to install the program as administrator right click on the installation program files and select run as administrator , click continue if you are prompted to confirm.

  Just check the items below that addresses a similar issue

  The feature you are trying to use is on an unavailable network resource
  http://support.Microsoft.com/kb/828376

  You receive an "error 1706. Valid any source not found for the product

  http://support.Microsoft.com/kb/253768

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows 7 cannot see my Mac on my home network

  I can share between the two computers, but my windows 7 cannot see the Mac when I go to the network in windows Explorer. However, I see the PC from the Mac. Both are under the same working group: MSHOME.

  Any help would be greatly appreciated,

  Brian

  Hello

  Please keep us informed about the issue.

  I think that the problem to which you may be due to viruses or malware.

  There could be chances that some settings were not correct or there could be a network congestion.

  You can also look at post Len Flier in the thread following parameters of Mac replied on September 29, 2012.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/still-cant-get-Windows-7-to-see-Mac-on-home/d6bd510c-A956-4984-8e80-66f784c904c3

  Feel free to visit our Web site for any help with the Windows operating system in the future.

  Thank you.

• Cannot see a drive after the installation of Windows 8.

  Hello guys, I just installed Windows 8 and unfortunately now I can't see my drive E: ...  It shows me in the disk management window, but I really do not see and cannot access this hard drive. If anyone knows how to the unhide it let me know, I have very important data in it.

  Here is my disk management window:

  

  And here is the my computer window, I can't see Drive 2 here.

  

  GG

  All what you need to do is give a drive letter.  Right now there are zero and why you can not see

• HP ay503tx: problem of charges windows installation error - no device, driver cannot see HARD drive

  I bought the HP ay503tx model that came with the BACK. I downloaded windows 7 x 64 ISO and I got the license with me original. But when I try to install windows 7 via USB it won't let me.

  After the boot from USB, it get up to page that says that windows install. and when I press install, it throws an error 'no driver device found ". I can't see any HARD disk where to install fresh windows.

  I saw a lot of solutions such as if we were trying on USB 3.0 etc, but nothing helped. Please help me.

  Hello:

  On the PC with the Intel Skylake chipset like yours, there is no support USB2 and the W7 installation media has no the USB3 support, so you are between a rock and a hard place.

  The solution that works for most is to use the tool below to integrate the drivers USB 3 of your installation drive of W7 USB flash media.

  There are instructions in the readme on the link below to learn how to use the tool.  It should be run on a PC with W8.1 or W10.

  https://Downloadcenter.Intel.com/download/25476/Windows-7-USB-3-0-creator-utility

• 2000-2b09WM HP: flashed the BIOS and now cannot see hard drives.

  I was trying to install Win7-64 on this 200-2b09WM. I flashed the bios, and now BIOS can even see hard drives.

  I used the 67259.exe softpaq file

  http://ftp.HP.com/pub/SoftPaq/sp67001-67500/sp67259.exe

  Any ideas on how to solve this problem because I can not install andy BONE and can not boot from floppy, cause there's not?

  Have you tried to boot with the Windows disk since the last error? If this laptop comes with Windows 8, it can have Secure Boot enabled to avoid booting from cd/dvd. Check the BIOS.

• Problems installing the new hard drive OSX iMac G5 A1076

  I have an Imac G5 A1076 model who needed a new hard drive

  The hard drive for now I can not install the OS!

  I formatted the hard drive using transmac on my Win 7 pc (since I don't have access to another mac)

  I also bought the 10.3 disk 3 cd OSX Install discs.

  When I put disc 1 in hold C and start the IMAC I get a gray screen with a gray circle with a line through it.

  Maybe I was reading that this is caused by installing is not the correct OSX?  I looked on everymac.com and found that it was originally shipped with os x 10.3.5

  do I need to get a drive to 10.3.5?  He will tell 10.3.5 the disk?  my 10.3 that I bought new in the box never open just says 10.3.

  Help, please!

  You need the original computer disks or details of Mac OS X 10.4 through 10.5.6 DVD.

  (137519)

• Machine of Windows 7 cannot see itself or other computers on the network.

  I work with a volunteer organization, is attempting to add a new computer to their network. Add the new computer is a laptop running Windows 7 Professional (32-bit, 6.1 build 7601).

  It is one of the three computers that connect via a wireless network, with the remaining three computers connected by Ethernet.
  One of the laptop is running Windows 7 Home Premium (64 - bit, 6.1 build 7601) and the laptop rest and three desktop computers running XP Professional (5.1, build 2600).
  The laptop running Home Premium has no problem with connectivity. He can see himself and all the computers on the network (with the exception of the new Windows 7 Professional machine). The XP machines can all be seen and also the machine Windows 7 Home Premium.
  The Windows 7 Professional machine, however, cannot see itself, or one of the machines running on XP. It may, for some reason, see the Windows 7 Home Premium machine.
  I can ping each computer on the network from him and he can ping other computers. I can even connect using his IP address and access the folders and files shared like this, but nothing I have seems to change him will appear.
  I tried to disable the Windows Firewall and Microsoft Security Essentials, neither of which has an effect any. The computers are all in the same workgroup and network machines Win 7 is set to work on both.
  I can't understand why this new computer should have these problems, I'm not a professional so there is probably something basic, I missed, but if anyone has any ideas I would be much obliged.
  Thank you very much.

  Hello

  The question you have posted is related to Windows 7 connected to an organization and would be better suited to the TechNet community. Please visit the link below to find a community that will provide the support you want.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  Thank you.

• Windows 7 cannot see Raspberry Pi Samba Server

  Hello

  I have two Windows 7 computers portable and a raspberry on my network Pi domestic.  The Raspberry Pi is configured as a Samba server.  Both portable Windows can see folders and each other, but only one of the portable displays the IP on the network.

  As far as I can see, both Windows 7 machines are configured identically.  On the machine that does not see the IP, I tried to disable the firewall, but that makes no difference.

  How can I study and fix this please?

  Best regards

  David

  Hello

  Thank you for visiting Microsoft Community.

  According to the description, I understand that your Windows laptops can see shared folders and each other, but only one of the portable displays the IP on the network.

  I suggest you to post your query on our Forums TechNet social as this question should be better there.

  Please refer to the reference to the link below to send your request:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information helps.

  Thank you.

  Sincerely,

  Ankit Rajput

• Windows 7 cannot see my external hard drive, even if I don't use it on this computer!

  I have 2 external hard drives, both worked well on Windows 7. Now, on the same computer, no change, they stopped from within the computer. Drivers fine and visible in the devices. all ideas

  Hello Gus,

  Windows 7, having trouble finding external drives is not uncommon. I use Aomei Partition Wizard to get Windows to recognize the drive; Download here: http://download.cnet.com/AOMEI-Partition-Assistant-Standard-Edition/3000-18512_4-75118871.html?tag=mncol;1 .

  Once installed simply click on the external drive, and then select Properties. Who should get the drive recognized by Windows. See if that solves the problem for you.

  Kind regards

  BearPup