1242AG lwapp cli config
Hello
I have a 1242ag AP lwapp I want to config via the console (I send to a remote site).
The AP has been previously configured, so I can't change anything.
I tried the command
CLAIRE LWAPP PRIVATE-CONFIG
But I get
ERROR! Command is disabled.
All suggest?
Thank you very much
Luigi
If a lwapp ap is unable to reach a DHCP server, you can manually configure static controller information using the power port injector console and CLI commands in EXEC mode. The static settings are configured with the CLI commands are used by the lightweight access point to connect to a controller. These CLI commands can be used only on lightweight access points that are not associated with a controller.
Also, REAP H access points that are in the connected mode will not allow the creation or disabling configurations via the console. When the access point is in this State, configurations must be done through the controller interface. Access to the access point configuration commands, if necessary, to ensure that the access point is in standalone mode before attempting to enter all the configuration commands.
Once the access point is connected to a controller at any time (even if the H-REAP is placed in stand-alone mode), console access point won't command configuration until a new password. Each REAP: password must be changed. This can be set through the CLI of the controller to which the access point is connected. The syntax of this command allows the controller to set the password of the individual access point console or the password to all the services of the controller access points:
(WLC_CLI) > ap config password username {all |}
: Note for an access point that did not have its console defined passwords, that this configuration is sent AP to point the command is entered on the controller. Access points that join later to this will require the command be entered again.
Again the access point has both received a default password and the access point is in stand-alone mode, the access point will still not allow access to these commands. To make changes to the configuration of the REAP H, the removal of pre-existing static IP addresses and IP address of the controller of the configurations is necessary. This configuration is called the private LWAPP Configuration and will need to be removed before any new access point CLI commands can be entered. To do this, enter the following command:
AP_CLI #clear lwapp private-config
Note: In order to completely return the access point to factory default, to the boot of access point, press the Mode button until Ethernet light turns orange.
Only at that point can be made of LWAPP configurations
http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_tech_note09186a008081103d.shtml
Tags: Cisco Wireless
Similar Questions
-
APs 1242AG LWAPP mode conversion problem
Hello
I have a few APs 1242AG to convert standalone in LWAPP mode. The conversion tool (v 3.4) keeps giving me an error saying that there is a list of firewall or preventing work TFTP access.
It is this time I use the internal TFTP server in the tool or TFTPD32 on the same PC or even if I leave the picture in TFTPD of flash on the 2960 POE switch I test the upgrade on the access point is connected to!
If do it manually one ' archive download-sw / overwrite/no-set-boot tftp: / /... ". "since the console telnet on the same access point, it downloads the image very well. I can also copy the config for my TFTP server!
It's driving me crazy ideas that I hurt APs to LWAPP mode.
Oh the WLC is a race 5508 latest 7.x code, but I don't think that's relevant here.
Concerning
Pat
Hi Pat,
It's just a warning msg.
Thank you
-
Substitution of WLAN in CLI Config
I currently have the box to open with TAC where my LWAPs lost their substitution parameters. The solution I gave is to manually add the SSID for substitution via the user interface settings. The GUI sucks for that. Can't search for text and that you cannot sort columns.
Y at - it a command to add the SSID for substitution in CLI settings?
Hey Wilfred,
Using the CLI to activate WLAN replacement
To turn on WLAN substitute the controller CLI, enter the following command:
activate wlan ap config {802. 11A |} 802 11 b} cisco_ap
To set the local wireless networks that you want to pass, enter the following command:
Add config wlan ap {802. 11A |} 802 11 b} wlan-id cisco_ap
The good doc.
http://www.Cisco.com/en/us/docs/wireless/controller/4.0/Configuration/Guide/c40wlan.html#wp1114777
I hope this helps!
Rob
-
Restore the saved CLI config since a 4.1 on a 4.1u1 host
Is this supported? Looking at safeguards identical to the host that looks like it might be possible.
Thank you
Should work just fine.
-
HOWTO specify the zone on UCS C220 M3 by CLI
Hello, I have configured NTP in the GUI, but bad weather due to a time zone is not OK
I can't change the time zone in the GUI, so I looked for some CLI commands.
According to this article, it should be possible to use the system to scope, but this command is not available in my CLI:
BKS-C220-FCH1743V1FY #.
commit the changes to batch validation
connect to Connect to another console
discard discard all changes
out of the shell
scope changes the current mode
set property values Set
view the system information see the
top of the page to go to higher modeBKS-C220-FCH1743V1FY #.
BKS-C220-scope FCH1743V1FY #.
BIOS system BIOS: Basic Input/Output System
certificate of security for SSH & SSL certificates
Chassis server items in stock
MMIC Cisco Integrated Management Controller
Configuration of alerts on the platform event/fault fault
Protocol http Hyper Text Transfer Protocol
IPMI Intelligent Platform Management Interface
console keyboard video mouse KVM to host
LDAP Lightweight Directory Access Protocol
salt of the system event log
sensor sensors
SNMP Simple Network Management Protocol
ground Serial Over Lan (console character of host mode)
SSH Secure Shell Configuration
local users of the user of this CIMC
sessions active user of user on this MMIC session
VMedia Virtual Media (local media on the host mount)
xmlapi Configuration API XMLBKS-C220-scope FCH1743V1FY #.
% Incomplete command
BKS-C220-FCH1743V1FY #.How should I change the time zone?
Hello
Unfortunately you have checked a guide old enough to UCSM 1.3 (we went through UCSM 1.4/2.0/2.1 and currently on 2.2 already), and that server you are trying to set up seems to be offline...
For a stand-alone server of series C, only 2 how time management is in the BIOS or Setup NTP (counting 1.5 MMIC) but not their time zone. See the screenshots attached.
If you join the server with UCSM then you can configure the time zone.
-Note ALL useful answers
-Kenny
-
Re: Is there a CLI on an AP command to show what controller it is attached?
Hello
I don't see the rcb of the order part. Other thoughts?
Thank you
Tim
1140 #debug lwapp customer?
debugs CC Call Control associated with
LWAPP Client Config Messages config
Customer LWAPP Error Messages error
event Client LWAPP debug event
LWAPP customer Metrics FMC FMC-metrics
your dot11 LWAPP Client redirection
Mgmt dot11 LWAPP customer mgmt
Debug LWAPP Client package package
LWAPP customer Fragment Reassembly reassembly
voice-metrics LWAPP customer voice Metrics
1140 #debug cap
1140 #debug capwap cl
1140 #debug capwap customer?
CAPWAP Client Config Messages config
detail CAPWAP customer detail Messages
Customer CAPWAP Error Messages error
CAPWAP Client Event Messages event
your dot11 CAPWAP Client redirection
hexdump CAPWAP customer Hexdump Messages
Info CAPWAP customer info Messages
LSC LSC events customer CAPWAP
Mgmt Mgmt CAPWAP customer dot11
package, the customer CAPWAP packages
payload CAPWAP customer payload Messages
CAPWAP customer dot11 probe
CAPWAP customer Fragment Reassembly reassembly
customer CAPWAP TCP - mss - MSS adjust adjust
TCP-mss-impression of CAPWAP SMS Client
Tim,
Show {capwap | lwapp} client config, or see the {capwap | lwapp} customer rcb, which will show you "MWAR" you are connected to, and which he knows
See you soon,.
Steve--
If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.
-
Reset a TOWER 1242 Ethernet interface
Is there a way to reset a 1242 IP and gateway (both are configured under the same IP address because a Cut ' paste error in the WCS... so the AP is not accessible and the DHCP failover will not work, because the AP can reach his false gateway...)
The AP is on a remote location, I can only ask the user to support onside. Is there an easy way to retrieve the AP do DHCP?
Hello
Restart the AP several times... It worked for me while troubleshooting at several customers... However when ever it does not... We need to get the console access to the AP and then issue the command below...
en
Debug lwapp console cli or debug console cli capwap
Claire lwapp private-config or claire capwap private-config
end
LWAPP ap ip
LWAPP ap controller ip
or
Debug lwapp console cli or debug console cli capwap
int fa 0
IP addr dhcp
end
This will do...
Let me know if that answers your question
Concerning
Surendra
====
Please do not forget to note the useful messages that answered your question or was useful
-
Hi team, Okay, so what we have observed in our network is that flow-export sometimes causes high interface utilization and as a workaround, we remove and re-add flow export commands. Now there are short burstd of traffic as well, so I want to add a condition where "burst happens 3 times in 60s, then trigger the event". As I cannot test in production router, so I am testing on a lab switch and there is not much traffic on it. txload/rxload is 1 and hence my applet looks like this: sw1-trn-mr3.hyd.shaw.net#sh run | b event manager event manager applet test authorization bypass event tag 1 interface name GigabitEthernet0/4 parameter txload entry-op ge entry-val 1 entry-type value exit-op lt exit-val 1 exit-type value poll-interval 10 event tag 2 interface name GigabitEthernet0/4 parameter rxload entry-op ge entry-val 1 entry-type value exit-op lt exit-val 1 exit-type value poll-interval 10 trigger occurs 3 period 60 correlate event 1 or event 2 action 1.1 cli command "enable" action 1.2 syslog msg "Interface utilization has risen again. " action 1.3 cli command "show proc cpu | append flash:test" action 1.4 cli command "show interface GigabitEthernet0/4 | append flash:test" action 1.6 cli command "show ip cache flow | append flash:test" action 1.7 cli command "show tech | append flash:test" action 2.2 cli command "no ip flow-export source GigabitEthernet0/4" action 2.3 cli command "no ip flow-export destination 192.168.1.1 2055" action 2.5 cli command "ip flow-export source GigabitEthernet0/4" action 2.6 cli command "ip flow-export destination 192.168.1.1 2055" action 2.9 cli command "end" ! end The thing is it does not work. I turned on debugs and I see this. Mar 3 15:30:46: fh_send_intf_fd_msg: msg_type=114 Mar 3 15:30:46: fh_send_intf_fd_msg: sval=0 Mar 3 15:30:46: fh_send_intf_fd_msg: msg_type=114 Mar 3 15:30:46: fh_send_intf_fd_msg: sval=0 Mar 3 15:30:54: fh_fd_intf_process_async Mar 3 15:30:54: fh_fd_intf_param_fetch:I/F=GigabitEthernet0/4 txload=1 Mar 3 15:30:54: intf_value_uint_compare:op1=1 op2=1 ret=TRUE Mar 3 15:30:54: intf_entry_value_check:Returning TRUE Mar 3 15:30:54: fh_fd_intf_event_match: re = 0x5849AA0, num_matches = 1 Mar 3 15:30:54: fh_fd_intf_start_poll_timer: start_t=10000 Mar 3 15:30:54: fh_fd_intf_process_poll_timer: update_t=0 Mar 3 15:30:54: fh_fd_intf_param_fetch:I/F=GigabitEthernet0/4 rxload=1 Mar 3 15:30:54: intf_value_uint_compare:op1=1 op2=1 ret=TRUE Mar 3 15:30:54: intf_entry_value_check:Returning TRUE Mar 3 15:30:54: fh_fd_intf_event_match: re = 0x56D793C, num_matches = 1 Mar 3 15:30:54: fh_fd_intf_start_poll_timer: start_t=10000 Mar 3 15:30:54: fh_fd_intf_process_poll_timer: update_t=0 Mar 3 15:30:54: fh_send_intf_fd_msg: msg_type=64 Mar 3 15:30:54: fh_send_intf_fd_msg: sval=63 Mar 3 15:30:54: fh_send_intf_fd_msg: msg_type=64 Mar 3 15:30:54: fh_send_intf_fd_msg: sval=0 Mar 3 15:31:04: fh_fd_intf_process_async Mar 3 15:31:04: fh_fd_intf_param_fetch:I/F=GigabitEthernet0/4 txload=1 Mar 3 15:31:04: intf_value_uint_compare:op1=1 op2=1 ret=FALSE Mar 3 15:31:04: intf_exit_value_check: re=0x5849AA0, returning=FALSE Mar 3 15:31:04: intf_exit_comb_check:Returning FALSE Mar 3 15:31:04: fh_fd_intf_event_match: re = 0x5849AA0, num_matches = 0 Mar 3 15:31:04: fh_fd_intf_start_poll_timer: start_t=10000 Mar 3 15:31:04: fh_fd_intf_process_poll_timer: update_t=0 Mar 3 15:31:04: fh_fd_intf_param_fetch:I/F=GigabitEthernet0/4 rxload=1 Mar 3 15:31:04: intf_value_uint_compare:op1=1 op2=1 ret=FALSE Mar 3 15:31:04: intf_exit_value_check: re=0x56D793C, returning=FALSE Mar 3 15:31:04: intf_exit_comb_check:Returning FALSE Mar 3 15:31:04: fh_fd_intf_event_match: re = 0x56D793C, num_matches = 0 Only the first time, it returns TRUE. After that, it returns FALSE always and hence the condition "trigger occurs 3 period 60" does not match and hence no event is triggered. Where am I going wrong? Appreciate your help on this.
Thanks.
You have a condition of release of ' lt 1. This means that the burden must fall below 1 until the event to rearm. In this case, it seems that the load is always 1, so you will not see the three events occur. You have to push some of the traffic through this interface to complete your test.
In addition, you are away:
Action 2.1, cli «config t» command
And probably, you will need to extend the first event with a maxrun parameter I am sure that this policy will have more than 20 seconds to run.
-
Certificate of default keychain is invalid
Hello
I put my UCS upgraded to version 2.0.3c, and everything works fine.
But when I upgraded the first FI, I got this Major error:
I dare not to upgrade the second FI, before correcting this error.
I have seen that this certificate is linked to a connection between the browser Client and UCSM.
I did not have any certificate when the UCS has been implemented (because there where some consultant who drew up the solution).
What it takes, I do?
/ Stig sand
Since you have not done something for the cert since its installation, all you need to do is regenerate default key ring.
Refer to this document, under "Regenerating the keychain by default":
ARO
Glenn B
-
Cisco SGE2010P LAG in access or trunk mode?
Hello.
I have a client who has two SGE2010P connected by four LAG ports.
Switch has all the users, and B a whole server. All used on the vlan 1.
Now I had to add the point with multiple SSID access.
Here the port I created trunk port since the AP had to pass several tag/no identified images.
So now the two trunk vlan is spent. One is the vlan 1 and other native vlan 2 for the wireless of comments.
If I were to set up access to this port, the AP Gets the ip address of the DHCP server on the other switch.
When I set up the trunk, the gi0.1, which is part of the vlan native Gets the ip address.
However, the Gi0.2 interface, which is part of the vlan 2 does not get an ip address.
When I put the port vlan 2 access mode and got the AP to be in this vlan.
I was able to get the ip address on the scope of vlan2. It's only when I set up the trunk port.
the vlan 2 (not native vlan) does not get an ip address.
So I think it is, maybe the LAG port is in access mode in the vlan 1 and not in trunk mode.
Is it possible to change the port of OFFSET to be in trunk mode?
Thank you in advance.
Hi Thomas, that there should be "M1" in the list of the interface down. Or some channel port that you assigned. As an OFFSET, these ports are more specific. It works exactly the same in a catalyst environment, difference is, it's on a GUI config vs a CLI config.
-Tom
Please mark replied messages useful -
Monitoring dual-core (supervisor engine 7-E) with a Script of the EEM.
Hello
I have a Cisco Catalyst 4500th 7-E supervisor engine and set up an EEM Script to monitor the dual core CPU Utilization by PRTG Network Monitor.
authorization of dualcore event manager applet work around
cron cron-event timer entry ' * * 0-6.
!
action 100 cli command "en".
action 120 cli command "see treat cpu | include five ".
!
action 220 regexp "Core 0: CPU utilization for five seconds: ([^ %] +) %; a minute: ([^ %] +); five minutes: ([^ %] +) %. ' * ' $_cli_result result c0cpu5sec c0cpu1min c0cpu5min
the 240 action if $_regexp_result eq 1
end of the 260 action
!
action 320 regexp ' Core 1: CPU utilization for five seconds: ([^ %] +) %; a minute: ([^ %] +); five minutes: ([^ %] +) %. ' * ' $_cli_result result c1cpu5sec c1cpu1min c1cpu5min
the 340 action if $_regexp_result eq 1
360 action ended
!
action 440, «config t» cli command
action 441 cli command "snmp mib expression owner cisco name c0cpu5sec.
action 442 cli command "$c0cpu5sec expression".
action 443 cli command "snmp mib expression owner cisco name c0cpu1min.
action 444 cli command "$c0cpu1min expression".
action 445 cli command "snmp mib expression owner cisco name c0cpu5min.
action 446 cli command "$c0cpu5min expression".
!
action 550, order cli "config t.
action 551 cli command "snmp mib expression owner cisco name c1cpu5sec.
action 552 cli command "$c1cpu5sec expression".
action 553 cli command "snmp mib expression owner cisco name c1cpu1min.
action 554 cli command "$c1cpu1min expression".
action 555 cli command "snmp mib expression owner cisco name c1cpu5min.
action 556 cli command "$c1cpu5min expression".
!
action 600 cli command 'end '.
!
end
It works fine, but on the recording buffer there are a lot of % SYS-5-CONFIG_I: configured from console by the vty0 (EEM:moncores) messages - one per minute - here is an example:
Oct 29 17:54:01: % SYS-5-CONFIG_I: configured from console by the vty0 (EEM:dualcore)
29 Oct 17:55:01: % SYS-5-CONFIG_I: configured from console by the vty0 (EEM:dualcore)
29 Oct 17:56:01: % SYS-5-CONFIG_I: configured from console by the vty0 (EEM:dualcore)
29 Oct 17:57:01: % SYS-5-CONFIG_I: configured from console by the vty0 (EEM:dualcore)
I considered logging remove duplicates command allows to prevent the consecutive record from multiple copies of the same system logging (syslog) message, but it is only available for the Cisco IOS XR.
Could someone help me to determine if it is possible to avoid this messages via the on-board system log manager, I tried to do this, but
I did not.
Kind regards
~ Sergio
You have found a bug in the converter. Modify your script and remove the token of type 'game '. Who should not have been in the converted Tcl code.
-
Configuration VIC 1225 in C240 problems
I'm trying to set up a server with the installed VIC 1225 C240.
Firstly, I would like to know if it is even possible to use it without fabric interconnections or Nexus switches. Suppose that I am just their regular snap up some 10GbE switches. I can change this but wante to have a better idea of my design decisions - not much info about when the VIC 1225 may or must be used outside this context. »
Secondly, I am following the instructions here:
I checked that the VIC is installed in slot 1 visually as well as via the output below, but the output below is not what I expected by the documentation. I am not able to enter into the scope of this adapter, and it appears in "display adapters pci" and not "adapters". It is as if she is not even recognized as a VIC.
Any help would be appreciated.
ucs-c240-m3 /chassis # scope adapter 1
Error: Managed object does not exist, use show command to list valid targets
ucs-c240-m3 /chassis # scope network-adapter 1
Error: Managed object does not exist, use show command to list valid targets
ucs-c240-m3 /chassis # scope pci-adapter 1
% Incomplete command
ucs-c240-m3 /chassis # scope pci-adapter 1
Press Enter key ucs-c240-m3 /chassis # scope
adapter Cisco Systems UCS Virtual Interface Card
dimm-summary Information common to all DIMMs
fan-policy Fan Policy parameters
firmware Get all Components Firmware
flexflash Cisco FlexFlash Controller
gpu Show GPU cards present in the system
hdd Host local hard disk drive
network-adapter Show network adapters present in the system
storageadapter RAID Controller
ucs-c240-m3 /chassis #
Matt,
The VIC 1225 is fully supported as a stand-alone card outside UCSM and by default it runs in the classic Ethernet mode which means that it is compatible with any standard IEEE 10GE switch.
The VIC is not supported in Slot 1 in the C240, he is supported in Slot 2 or 5
(http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C240/install/replace.html#wp1337242).
Without be installed into the cracks, the connector of NC - if at the end of the PCIe bus will not be conencted and the MMIC has no interface to configure the card. Once you have installed it in a supported housing, you should be able to frame scope and show the adapter. Then brought to the map as shown below
UCS-c240-m3 # chassis range
UCS-c240-m3 /chassis # Show map
Seller of product ID of the Slot PCI product name serial number
-------- -------------- -------------- -------------- --------------------
UCS VIC 1225 FCH162974VP UCSC-PCIE-2 C... Cisco Systems Inc.
UCS-c240-m3 scope adapter /chassis # 2
UCS-c240-m3/chassis/adapter #.
If you are able to see that your VIC made me know if you have additional questions.
Steve McQuerry
UCS - Technical Marketing
-
Does anyone know how to reset a UCS system to the factory settings? We have a lab of the UCS to the office and we must be capable of resetting to factory settings so that several people can learn how to build a system UCS from the ground upward.
Glad that worked.
Here is a direct link with the command in our documentation:
You can find the full guide here:
http://www.Cisco.com/en/us/products/ps10281/products_installation_and_configuration_guides_list.html
-Justin
-
Fabric connecting LDAP authentication
Hi guys,.
I am running 2.0(2q) UCSM
I was wondering if there was a way of configuring LDAP authentication by logging in via SSH to the FIs?
I installed all group mappings and adds users to these groups without any problems, but I can't seem to figure out how to get LDAP for authentication when you use a session SSH on the FI.
Someone at - he put in place before?
Thank you
Doug,
Are you sure you are using the correct syntax when connecting via CLI?
If AD authentication works through the GUI, it should work in CLI.
Kind regards
Robert
-
How to change IP cluster and management for the two interconnections Faric
I need to change the IPs. How can I do this using the console? It was easy enough implemented, but something else when I need to change the addresses...
This isn't the production
Post edited by: Atle Dale
Atle,
This should help you:
. / Afonso
Maybe you are looking for
-
No bar to Add on more, some modules no longer displayed because of this.
Due to the new update and the removal of the add-on bar that usually not resident at the bottom (also known as the status bar) I have Add-ons installed that work which no long appear to all THE. He is not here in the new side icon thingie you can cli
-
Satellite Z939-13N - problems Win 8.1 security update KB2961908
Satellite Z939-13N Not update Windows 8.1 specifically: Security for Windows 8.1 update for x 64-based Systems (KB2961908) without KB2919355 Status 'failure '.
-
Portege 7020CT: battery is dead
HelloI have an CT 7020 and my battery is dead, it works 2 min. - does anyone know if there is any way to repair a battery or sell everything for this place... cheapper!
-
virtual xp does not recognize logitech gamepad - has no usb devices
Hello. I'm having difficulty to connect a Logitech Attack 3 joystick to Virtual PC article from my XP computer The joystick is supposed to log in via usb, but does not appear in the display of the devices, so therefore can not be selected. If I retur
-
Left hinge of the m6 between HP laptop separates housing
Hello I have the same problem that a few people have reported. When I raise the screen, the left hinge area is at the origin of the case separate in this corner. Can someone please? Thank you.