16 bit CRC IBM

Similar Questions

• 8-bit CRC-CCITT

  Hello

  I'm trying to generate a bit 8 CCITT CRC with the polynomal 9-bit U3 + U2 + U4 + U8 + 1

  I have studied and tried to change the CRC 16 bit found here calculator and Vi post by Shoneill here, but I'm getting nowhere...

  Generator of CRC should be initialized to 0, LSB is sent first.

  In the datasheet, I found the example:

  Data 1:1010 0000

  2 data: 0000 0011

  CRC: 0010 1010

  Any intervention on how I can modify the existing 16-bit calcultors, or would it be a better idea to start from scratch?

  Solved. Change the shoneill vi finally gave me the result I needed.

• Get the error access denied when you try to install Windows 7-64 bit Okidata IBM-ML321 of windows update. Error reported in the newspaper like 80070005

  Can install printer drivers which are in 'standard list of printers', but when I try to install a local printer and choose update windows for the Okidata IBM-ML321 on Windows 7-64 bit driver, it errors when you try to install.

  Hi David,

  I suggest you scan the computer antivirus using the Microsoft Safety Scanner.

  Microsoft safety scanner will help us to get rid of software viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note:

  1) the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  2) if you run the virus scan of the program which is infected with the virus will be deleted. Therefore, reinstall the program. Also, if files and folders are affected by the virus, while they might even get deleted.

  Hope this information helps. Answer the post with an up-to-date issue report to help you further.

• I2C/SMBus Melexis MLX90614 IR Termometr

  I use the interface NOR-8451 read the temperature of the thermometer IR Melexis, who use the SMBus Protocol.
  Use the I2C mode I can read RAM for display of the actual temperature, but can not cooperate with EEPROM. Has no made communication with thermometer?
  There are some specific behaviors: infrared device respond to each address, but there is no result for the address change I2C/SMBus (sholud) command.
  I did all the sugested (such as disconnection/reconnection) shares and still have the view to each address.

  In fact I need three or four devices to one bus and this is the reason why I'm looking for solutions.

  Ok. I see 4 errors in your code

  1. on your Read_Termometer_NI_send.vi, you are only reading 2 bytes on reading when it appears that the Melexis returns 3 bytes (data Low, High Data, PEC).

  2. you do a left shift on the I2C_Termom_Addr of 1. Our API uses a 7-bit address. With the default address of 0, it is well, but when you change the address it will no longer work.

  3. on your writing, you split the request in the multiple Scriptures (writing (command), writing (given Low, High Data, PEC)). This will create the incorrect model on the bus. You must use a single entry with 4-byte. Also, I don't know if reading will do nothing good. You should probably always do a read/write. Again, he would do a reading of 3 and an EEPROM_SMBus_Address to read again just writing.

  4. you get a zero for the PEC. I think it must be correct 8-bit CRC on the first three items (command, Dala Low, High Data) or else command is likely to be rejected by your device.

• Driver digital camcorder model # DCR - TRV350?

  I have a digital camcorder model # DCR - TRV350 that I try to use Windows 7, 64-bit, but it seems that I need an updated driver to use. I would be very pleased with the ideas. Thank you, pepper

  There is no 64-bit drivers for usb connections. What we can do is upgrade to Windows 7 Professional that can run Virtual Windows XP mode

  http://Windows.Microsoft.com/en-us/wind... ws-xp-mode

  The USBDRVEN installer will work in Virtual Windows XP and
  install the drivers correctly and also a link between the installation of
  Windows 7 with a virtualization USB Driver Connector.

  I don't know if it will work properly with Windows 7 Professional 64 bit, because I have a 32-bit computer (IBM T60P
  ThinkPad running Windows 7 Professional 32-bit)

  Contact Microsoft and ask questions about your particular
  computer first before you upgrade.

• need help to connect my sony DCR-HC23 handycam to pc

  Hello
  IM interesting to connect my sony DCR-HC23 handycam to my pc, so I could save / change my mini dv.
  the cam has 3 exits:
  One - came out to connect to tv.
  second - a USB 2.0 A to Mini-B cable
  third a dv out.

  Since I don't have a dv out and im tring to connect the cam via cable usb but nothing happens.
  I have to fall on this page:
  http://www.Sony.co.in/support/FAQ/141031
  Ive downloaded and now windows (windows 7 64 bit premium) recognize somethnig but in the end, I get *! * to the Device Manager and it says the material used recognized.

  Anyone know what what should I do?

  There is no 64-bit drivers for usb connections. What we can do is upgrade to Windows 7 Professional that can run Virtual Windows XP mode

  http://Windows.Microsoft.com/en-us/wind... ws-xp-mode

  The USBDRVEN installer will work in Virtual Windows XP and
  install the drivers correctly and also a link between the installation of
  Windows 7 with a virtualization USB Driver Connector.

  I don't know if it will work properly with Windows 7 Professional 64 bit, because I have a 32-bit computer (IBM T60P
  ThinkPad running Windows 7 Professional 32-bit)

  Contact Microsoft and ask questions about your particular
  computer first before you upgrade.

• computer 37 can laptop XP continues to tell me memory online someone please advise me as to what I should do? Thank you very much.

  'Hi' and thanks for taking your time in this matter. I have a 32-bit xp (IBM). He started to give me a message not enough memory on line 37 and now I get messages saying: it seeks to increase storage space. My xp freezes and I don't always get the messages that responded to the questionnaire. If you could help me please I would be very happy. Thank you for your time.

  out of memory in any line is generally a problem of Web page

  but, you can assign the system managed pagefile, so Windows will have enough memory to do what he must do.

  go to start, right click on my computer and choose Properties

  Advanced performance, settings tab, Advanced tab, choose virtual memory, click on change

  put check into touch for the managed system, success TOGETHER, right out and then reboot the pc.

• Create the circuit of the STS - V between 2 15454 SONET with CE100T

  Hi all

  I have a problem that I can't find documentation for.

  I create an ethernet point to point circuit between 2 15454 SONET with CLC ver 8.5 knots.  The circuit will carry you a VLAN not routed between switches, Cisco 4948 in 2 data centers.  I use CE100T-8 cards which the ethernet 100/full value, checked the Frother.  The POS is configured with a GFP - F frame and 32-bit CRC.  Type of circuit is a single STS - V STS to 50Mbit of bandwidth.

  The switch ports are configured as access ports on the VIRTUAL LAN set to 100/full.  At the end of B, the connection between the switch and the port of THIS is a straight through cable.  End is a crossover.  switch ports are configured as such:

  switchport access vlan 512

  switchport mode access

  switchport nonegotiate

  Speed 100

  full duplex

  Problem I have is that end A "Transport Layer failure" alarm to end and end B has the 'Carrier loss on the LAN' alarm near end.  No end shows an ethernet connection

  Wiring has been tested, I've tried other ports on the CE and have deleted and recreated the circuit board.

  What simple step/setting I'm missing?

  Thank you in advance,

  Jim Bowen

  [email protected] / * /.

  Jim,

  It seems that your problem is by your side B that has the loss of carrier on the LAN. The failure of Transport layer will be on the end node in these cases.

  You mentioned that the end B is a straight through cable from the switch to the CE card but the side is cross. The first thing you can try is to put a cable on the side B as well because it looks like the side of A working very well (doesn't have the loss of carrier on LAN).

  I don't remember if cards of IT have an option to hardcode the speed and duplex but if they can only so if the suggestion of cable does not work. If this does not work, you can try setting autonegotiation on switch and the map of THIS to see if it solves your problem. Once the loss of the carrier and LAN to clear alarm you should be up and running.

  Also, I can't remember if the EC supports the loopback test, but if you can try try to put a Terminal loop on the B side (it's optical to) your end should appear and your switch should appear/maximum looping. I would like to know how things work out for you. Looks like you're almost there a few tweaks should get running.

  Thank you.

  Ryan

• Need help on Oracle trade management Matrix environments

  Hi all

  I'm looking for details of supported environments for ATG v11.1 Matrix.

  I googled and found this link: https://support.Oracle.com/epmos/faces/DocumentDisplay?ID=1345041.1

  But it is asking for support IDs.

  Any help is appreciated.

  Thank you

  Mamadou

  To download this doc, you must indeed the identifier of customer support, but for your quick reference, here are the details for some of the environments supported for Oracle trade 11.1.0.0 that you may be looking for.

  Application server:

  Oracle WebLogic (WLS) - 12.1.2

  IBM WebSphere (has BEEN) - 8.5.5.1

  JBoss - 6.1.0 EAP

  DB:

  Oracle - Oracle Exadata

  Oracle - 12 c (12.1.0.0)

  Oracle - RAC (12.1.0.0) 12 c

  Oracle - 11 GR 2 (11.2.0.2.0)

  Oracle - 11 GR 2 CARS (11.2.0.2.0)

  IBM DB2 - 10.5

  MSSQL - 2012

  MySQL8 (dev. Only) - 5.6.11

  JDBC driver

  Thin Oracle - 11.2.0.3, 12.1.0.1.0

  MySQL connect (dev. only) - 5.1.24

  Microsoft SQL Server JDBC - 4.0

  iNet Merlia - version 8.0.2

  DB2 Universal driver - 3.67.26

  JDK

  Oracle Java - 1.7.0_55 (64-bit)

  IBM SDK - 1.7 SR1 (64-bit)

  Thank you

• Cut and paste files

  All those who use VMWare Player could cut and paste the files on a DVD RW drive on a comments system? Thank you.

  ODA

  ----------------------------------------------------------------------------------------------------------------------------------------

  14/01/2011

  Found a solution for the "DVD RW cut and paste problem" in my Windows XP feedback system.

  Installed the package free writing Drag2Disc software for Windows Vista (32 bit, 64 bit), XP (32-bit, 64-bit) of IBM/Lenovo on system invited and formatted a DVD disc.  Everything seems to work fine on the DVD RW drive systems of the host and the guest.

  The available Drag-to-Disc packet writing software can be downloaded from the following site:
  http://www-307.IBM.com/PC/support/site.WSS/document.do?sitestyle=Lenovo & lndocid = RAHUL-40970

  Thanks for the suggestions everyone.

  ODA

  you set up the writer as IDE

  in my experience, you must configure it as SCSI
  See http://sanbarrow.com/vmx/vmx-cd-settings.html

  even then, I'm not sure if the packet writing is supported - software for CD burning ordinary as Nero and others should work well

• Migration Oracle Applications 12.0.6 from Linux to AIX.

  Please give me the id of document "Migrating Oracle E-Business Suite R12.0.6 with base 10.2.0.3 on Linux 32-bit for IBM AIX 64-bit"
  
  Source:
  Request = 12.0.6
  Database = 10.2.0.3
  OS = Linux 32-bit
  Worm = 4.8
  Single node environment.
  
  Target:
  Request = 12.0.6
  Database = 10.2.0.3
  OS = IBM - AIX
  Worm = 5.1
  Single node environment.
  
  Kind regards.

  Please view these docs/links.

  Note: 438086.1 - Platform Migration Oracle Applications version 12
  Note: 756086.1 - Oracle Applications R12 Migration of Solaris for the Linux platform

  Migration of Application E-Business Suite for Linux-tier servers
  http://blogs.Oracle.com/stevenChan/2010/02/migrate_ebs_apptiers_linux.html

  Assortment of Oracle E-Business Suite platform
  http://blogs.Oracle.com/stevenChan/2010/02/oracle_e-business_suite_platform_smorgasbord.html

  To migrate the database, you can use export/import or transportable tablespaces - refer to these docs for more details:

  Note: 454616.1 - export/import process for Oracle E-Business Suite Release 12 using 10 gr 2
  Note: 734763.1 - using Transportable database to migrate, E-Business Suite R12 using Oracle Database 10 g 2 or 11g

  Thank you
  Hussein

• Limit of Maxextent reaching index Segment

  Oracle Version 9.2.0.8.0 - 64 bit Production
  
  IBM AIX operating system version
  
  
  Hello
  
  
  I am facing a problem with Index segment limit maxextents.
  
  The EXTENSIONS MAX_EXTENTS columns and in the DBA_SEGMENTS for this Segment of the Index is 1.
  
  I tried to increase this size maxextents for this segment, but I get this error message.
  
  ALTER index... storage (maxextents 5)
  *
  ERROR on line 1:
  ORA-25176: specification of storage not allowed for the primary key
  
  
  I found that the Tablespace containing this segment is managed dictionary.
  
  Is this problem because of the storage space managed dictionary?
  
  How to solve this problem?

  What is an index organized table?
  If so you can't change the definition of the storage of the index - you need to do this on the table associated with the altar storage (...) syntax table.

• I have an IBM 64 bit machine that came with a windows XP pro COA. Can I use this COST to install XP 64 bit?

  I have an IBM 64 bit machine of zeon who came with a windows XP pro COA.  I installed XP pro 32 bit.  Now I want 64-bit. Can I use this same COST to clean install XP pro 64 bit? If so, were to get a 64-bit OEM disc. And I don't want Windows 7.

  Hello

  You must ask for Windows XP 64 bit CD from manufacturing.

• I need to find ibm proprinter III 64 bit drivers for windows 7

  Hello I need to find ibm proprinter III 64-bit drivers for windows 7 or a another pilot who works in the same way, it is that I don't need to change the impression of my software settings.

  Good bye

  Fabio

  Any driver for win7 or Vista would be provided by the manufacturer of HW, IBM

  Or windows Update can have built in driver If IBM does not provide a

• How to install win. 8 64 bits on my IBM Thinkpad T40 32-bit

  How to install win. 8 64-bit ISO on my IBM T 40 Thinkpad 32 bit dvd

  Moved from the installation of XP, set at level and activate Forum.

  To learn more:

  http://answers.Microsoft.com/en-us/Windows/wiki/windows_8-windows_install/how-to-migrate-from-32-bit-versions-of-Windows-to/46a5b8f6-5fd3-4C67-9482-4573087480fb