2.4 Ghz radio not found during the investigation of site
Hello. Today, I was on a site where people are wondering about wireless performance. This is a site where are only 10 users per AP, as you can see in the attached picture.
When I was at the local level marked in a red circle, I found the following
SNR:30
power:-64dBm
frequency: 5 GHz
Flow rate of 25Mbps download; Download 38Mbps
It has been tested with my laptop and Intel® WiFi Link 5300 adapter.
Although it seems all good, I try to find the 2.4 Ghz radio, but the software I used (Covera, Xirus, Inssider) cannot find the radio. I waited 10 minutes, and sometimes the radio appeared for 10 seconds and disappeared again. This is not the first time that occurred to me.
I also checked the auto-rf in the CLI WLC and attached the two.
No idea what is causing the radio0 to appear and disappear?
nothing wrong with the AP radio,
(1) not reset radio:
Last radio reset code: 37 Radio resets - total:5 retries:0 failed:0 Reset Stats: Start Cnt: 4, Recovery: Cnt 0, Last Ret: 0, Fails: 0, Recvry Status: Stalled NO, In Prog NO Code/Count: 37/00003 1 62/00001 1 67/00001 0
(2) no radio breaks down (rcore.d0):
2 -rwx 287 Jan 1 1970 00:19:44 +00:00 info 3 -rwx 246 Jun 26 2015 10:17:41 +00:00 env_vars 4 -rwx 55762 May 24 2015 03:00:14 +00:00 event.log 5 -rwx 64 May 24 2015 03:00:10 +00:00 sensord_CSPRNG0 38 drwx 576 Jan 1 1970 00:19:37 +00:00 ap3g2-rcvk9w8-mx 6 drwx 2176 Mar 16 2015 14:38:19 +00:00 ap3g2-k9w8-mx.153-3.JA3 74 drwx 0 Mar 1 1993 00:01:08 +00:00 configs 281 -rwx 3567 Jan 19 2015 15:46:17 +00:00 private-config 75 -rwx 75 Jun 29 2015 09:09:04 +00:00 capwap-saved-config 76 -rwx 7192 Jun 29 2015 09:09:05 +00:00 private-multiple-fs 77 -rwx 64 May 24 2015 03:00:10 +00:00 sensord_CSPRNG1 78 -rwx 965 Apr 30 2015 16:59:55 +00:00 lwapp_mm_mwar_hash.cfg
(3) there are for clients connected to this wireless AP:
Channel Utilization.......................... 9 % Attached Clients............................. 7 clients
(4) the adjusted maximum Tx power:
### Tx Power: Dot11 Config Serving Channel 1 (Type 0) Active Level Index 1 (Unitless) Active Level 16 dBm (OFDM 16 dBm) IEEE MIB format TRUE Metric unit dBm
(5) what I just noticed is that the AP has ID 4 and 4 attacks:
*Jun 26 13:06:11.575: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:5 Channel:1 Source MAC:5cb5.245b.66f8 *Jun 26 13:06:12.579: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:5 Channel:1 Source MAC:5cb5.245b.66f8 *Jun 26 13:26:13.267: %WIDS-6-SIG_ALARM_OFF: Attack is cleared on Sig:Standard Id:5 Channel:1 *Jun 26 13:26:13.267: %WIDS-6-SIG_ALARM_OFF: Attack is cleared on Sig:Standard Id:5 Channel:1 *Jun 26 17:18:06.727: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:4 Channel:1 Source MAC:58a2.b5b0.1b06 *Jun 26 17:18:06.727: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:5 Channel:1 Source MAC:58a2.b5b0.1b06 *Jun 26 17:18:08.735: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:4 Channel:1 Source MAC:58a2.b5b0.1b06 *Jun 26 17:18:08.735: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:5 Channel:1 Source MAC:58a2.b5b0.1b06 *Jun 26 17:38:09.443: %WIDS-6-SIG_ALARM_OFF: Attack is cleared on Sig:Standard Id:4 Channel:1 *Jun 26 17:38:09.443: %WIDS-6-SIG_ALARM_OFF: Attack is cleared on Sig:Standard Id:4 Channel:1 *Jun 26 17:38:09.443: %WIDS-6-SIG_ALARM_OFF: Attack is cleared on Sig:Standard Id:5 Channel:1 *Jun 26 17:38:09.443: %WIDS-6-SIG_ALARM_OFF: Attack is cleared on Sig:Standard Id:5 Channel:1
4 ID = toggles Assoc
5 ID = toggles Auth
Just check again later, you should see this SSID
Tags: Cisco Wireless
Similar Questions
-
taskdef class not found during the generation of code from wsdl using Ant
I'm getting a class not found error during the generation of the java code from the wsdl file.
*******************
CU dmwls (338) $ ant generate wsdl
BuildFile: build.xml
++ BUILD FAILED ++
++ file:/ffdt01/resmgt/kul/build.xml:14: taskdef class weblogic.wsee.tools.anttasks.WsdlcTask can not be found ++
Total time: 1 second
CU dmwls (339) $ cat - n build.xml
< default project 'all' = > 1
2 < name = "bea.home property" value="/opt/bea/wls/8.1sp4" / > "
"3 < name ="jdk.home property"value =" ${bea.home} / jdk142_05 "/ >
"4 < name ="weblogic.home property"value =" ${bea.home} / weblogic81 "/ >
5
6 < path id = "weblogic.classpath" >
"7 < fileset dir="${weblogic.home}/server/lib ">
8 < include name = "*.jar" / >
9 < / fileset >
10 < / path >
11
12 < taskdef name = "wsdlc.
13 classname = "weblogic.wsee.tools.anttasks.WsdlcTask"
14 classpathref = "weblogic.classpath" / > "
15
16 < name target = "generate-to-wsdl" >
17 < wsdlc
18 srcWsdl="/ffdt01/resmgt/kul/ksr.wsdl.
19 destJwsDir = ' / ffdt01/resmgt/kul.
20 destImplDir = ' / ffdt01/resmgt/kul.
21 classpathref = "${weblogic.classpath}" "
22 classpath = "${weblogic.classpath}" "
23 packageName = "examples.webservices.wsdlc" / > "
24 < / target >
25 < / project >
*******************
I checked this class in the use of weblogic.jar file unzip command but there is no class "WsdlcTask".
Unzip weblogic.jar-l | grep WsdlcTask - does not result
I am looking WsdlcTask class in all the jars under BEA_HOME directory using below command but not found in class WsdlcTask.
CD $BEA_HOME
To find. -*.jar name-exec unzip {}-l------. grep WsdlcTask - also returned no results
Some required classes does not appear in my weblogic.jar/jar file or there is something wrong with my build.xml file?
Help, please.
KuldeepHi Kuldeep,
WSDLC you use in WLS8.1 ehich is not correct... "weblogic.wsee.tools.anttasks.WsdlcTask" the above taskDef is present WLS9.x leave.
Please use the next task for WLS8.1 (http://download-llnw.oracle.com/docs/cd/E11035_01/wls100/webserv_ref/anttasks.html#wp1075710)
<>
WSDL = "WSDLs/MyService.wsdl"
destDir = "myService/implementation.
packageName="example.ws2j.service"/ >Thank you
Jay Sensharma
http://jaysensharma.WordPress.com/webservices/ (WebLogic wonders are here)Published by: Jay SenSharma on February 16, 2010 13:30
-
HP pavilion g4-1304au notebookpc - HARD drive is not found during the installation of Windows XP
name of the product - hp pavilion g4-1304au notebookpc
product no - #ACJ D4X79PC
processor - AMD A4 - 3330 X
During the installation of windows XP, it shows an error that the "mass storage is not recognized.
Please give me Slipstreamer pilot for the specification above.
You can follow the instructions in the following document, which allows you to install Windows XP on your laptop.
Also make sure that you install the last Windows XP SP3 for laptops and get into the BIOS and change a SATA AHCI to IDE / legacy mode.
Also, if there is a parameter called "Secure Boot", disable it.
I hope this helps.
-
Hello
I realize this has arisen before but other that the proposed upgrade to v4 pxelinux.0 solution (which I did), I can't solve my current problems of pxeboot default due to #.
Tools.T00: file not found on a network of esxi 5.5 installation
That's what I see in the tftp log:
Dec 09 17:07 ptc34551.hursley.ibm.com as [14604.1840335168]: /esxi55/tools.t00 to 9.20.170.34:49234 serving
Dec 09 17:07 ptc34551.hursley.ibm.com as [14604.1840335168]: width option-> 167559911
Dec 09 17:07 ptc34551.hursley.ibm.com as [14604.1840335168]: blksize option-> 1408
Dec 09 17:07 ptc34551.hursley.ibm.com as [14604.1840335168]: file asked to increase much, BLKSIZE
which according to VMware KB: ESXi 5.x fails to install when using PXELINUX is due to running a 32-bit version of pxelinux.0
rpm of syslinux containing pexboot.0 is syslinux-tftpboot - 4.02 - 7.2.el5
The other suggestion to avoid tftp to build the vmware host must use nfs in the boot.cfg settings.
It was a post that not solved and the settings, I did to get the system to build via nfs instead of tftp failed
If anyone has any ideas it would be great
Concerning
Paul
Hi Paul
Tools.T00 contains the iso files that you will need to install vmware tools.An installation without tools.t00 seems to be fully functional - but I'm not 100% sure on this subject.
My suggestion has been designed for troubleshooting - so if possible to continue your search for the real problem.Your tftp can be used not the largest files x MBs - either you hit a timeout - because the package does not arrive fast enough.
Ulli
(here I made a testsetup without tools - if I find other missing features I'll let you know...) -
I downloaded the wizard XI of customization of Adobe and the Adobe Reader XI .msi file. I'm looking for only three options to customize this app. When I try to save the .msi file, I get an error "setup.ini file was not found.
I placed the .msi file in a folder on the desktop. In addition, I tried using 7 - Zip to extract the .msi file in order to find the setup.ini file.
Where is this file which is located? What is the solution?
Any help is very appreciated.
Simply install Adobe Reader on a computer. Then, you will get the flat files in a folder with the Setup.ini file. It will be something like that, depending on your operating system:
Windows 7 64-bit example location
C:\ProgramData\Adobe\Setup\{AC76BA86-7AD7-1033-7B44-AB0000000001}\
-
Link to 'help journal online events' event viewer returns a page not found on the technet Web site
Whenever I click on the link "online help for event log" of event viewer for further help on an error, it returns the page not found on TechNet. Why? If Microsoft has moved the page, or something, why has he not updated the links in this application? I use Windows 8 (upgrade of Windows 7) and all applied Windows updates.
Well, I spoke with Microsoft Support Thursday and it seems that the Event Viewer online Help is not available yet in Windows 8.
While I took for them they connected to my system then tried their own with the same results, they then got on the? (could be the resource group... can't remember) who told supporters that on line assistance has not been fully developed for Windows 8 and therefore has not been published!
-
Media information was not found during the rip?
Recently it started to happen. The information is not being downloaded. None of this. Am online during extraction is performed.
Has he started recently?
If so, you can try using System Restore to when it was working properly.http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore
Alternatively, you can try to manually update the information manually and see if it works.
http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-edit-media-information-in-Windows-Media-Player -
Printer not found during the network printer share driver
I have a top of desktop windows xp with a printer and want to share with a computer laptop windows 7. When I click on the printer it looking for a pilot and says that he can not find a
You must install the driver of Windows 7 on your Windows 7 computer. It can be hard sometimes depending on the manufacturer provided the pilot, but the General procedure is:
1. get and install the appropriate driver for Windows 7 on the Win 7 machine. Install a LOCAL printer using a port local (LPT1 is fine).
2 once installed open the printer properties and add a local port. Enter the name of the port as \\XPPCNetName\PrinterShareName. -
model not found on the lenovo Web site
I recently purchased ideapad lenovoZ580, but I do not find this laptop model in the Web site.
I have need for support and software update for this model.
model no: 59-383215
3rd generation of Intel ci3 3110 m
Windows 8 64-bit oem
4 GB of ram
hard drive 500 GB
DVD player
Hello
This option was there before, but it is not available now. Mainly because, most of the machines of a model have the same mother with the exception of the graphics card. Even the processor is switchable (graphics card is not). So for this reason, all void models are compatible with the same drivers except for wifi (since it may be different and you know) and gpu.
Concerning -
Original title: Plustek OpticBook 3600 is not installed
Found new hardware wizard runs, but after scanning stops the disc from the manufacturer with the message ' year error occurred during the installation of the device.» The required section was not found in the INF"
PC system is homebuild which, in theory, exceed the minimum requirements of the system of manufacturers. Operating system is Windows XP Pro with Service Pack 3. The scanner is connected to the USB 2.0 card that is not separately powered, but installed in the PCI slot. I suspect that the problem lies in the PC rather than the scanner. but do not know what the problem is. Any help would be appreciated!
Hello
You can try the troubleshooting provided in the link below steps to fix the problem.You receive a "unable to install this hardware" or "an error has occurred during installation" error message when you try to install a PCI device
http://support.Microsoft.com/kb/841567
Note:
To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
How to back up and restore the registry in Windows
http://support.Microsoft.com/kb/322756
See also:
Error message: cannot install hardware. An error occurred during the Installation of the device
-
During the installation of Microsoft Service Pack 3, I get the message "The expected Version of the product is not found on the system."
Steps to take before you install Windows XP Service Pack 3
http://support.Microsoft.com/kb/950717How to troubleshoot an installation fails on Windows XP Service Pack 3
http://support.Microsoft.com/kb/950718How to obtain the latest Windows XP service pack
http://support.Microsoft.com/kb/322389Downloads of SP3: -.
Windows XP Service Pack 3 - file to Image CD ISO-9660:
http://www.Microsoft.com/downloads/details.aspx?FamilyId=2FCDE6CE-B5FB-4488-8C50-FE22559D164E&displaylang=enWindows XP Service Pack 3 for developers network installation Package and the professionals (unique facilities for the PC can use the same file)
http://www.Microsoft.com/downloads/details.aspx?FamilyId=5B33B5A8-5E76-401F-BE08-1E1555D4F3D4&displaylang=enHow do you know if you are running a 32 bit / X 86 or 64-bit computer
Click Start.
Do right click my computer and then click Properties.
If you don't see "x 64 Edition" in the list, then you are running 32-bit Windows XP.
If "x 64 Edition" is listed under system, you are running the 64 bit version of Windows XP.
-
I got the error message 'the expected version of the product was not found on the system' when I was installing Microsoft Office Professional 2003 Enterprise Edition (Microsoft Office Outlook 2003 with updated business contact to update Manager) Service Pack 1. I wonder that someone has a solution to resolve this error message. Your help is greatly appreciated.
Jim
If which are not related to the situation, suggest it ask you for help by the experts of the Officeinstallation, modernization, and activating Microsoft Office products Forum.
MowGreen Services update - consumer safety
-
I recently bought Age of Empires 3 and tried to install it. I get to drive three - until almost the end - when I'm "error 1334. Cannot install the file 'hispaniola_map.ddt' because the file is not found in the file ' Disk3C ~ 1.cab '. This may indicate a network error and the error reading CD-ROM, or a problem with this package. "The installation continues until the end of the progress bar, but it reads"Rolling Back Action"for about fifteen seconds before I got a"feature transfer error", which reads" error:-1603 Fatal error during installation. " Consult the help of Windows Installer (Msi.chm) or MSDN for more information. "Then, the Setup program stops and tells me that the game failed to install and my system has not changed. I cleaned the disk and it is in good condition. My computer also meets all the requirements for the game. I looked everywhere for an answer, but so far none has solved the problem. I tried to install it without the firewall and antivirus software running, in addition to install in safe mode. Any suggestions?
Hi void 1337,
Follow the suggestions below for a possible solution:
Method 1: I suggest that you put the computer to boot and then try to install the game and check to see if it helps:
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
http://support.Microsoft.com/kb/929135
Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.
Method 2: You can also follow the link and check if it solves the problem:
Error message when you install a Microsoft game or a mapping program
http://support.Microsoft.com/kb/258496
You can also view the article mentioned below to learn more:
Microsoft games: InstallShield Error Messages
http://support.Microsoft.com/kb/910816
If the above mentioned methods do not work, then post your request in the age of the forum of the empire for further assistance:
http://Forum.AgeCommunity.com/
Let us know if that helps.
-
ADVAPI32. DLL - the entry point of procedure not found in the dll
I just updated my OS from Win XP x 64 for Win 7 x 64. On my XP, I had a program called VVD works just fine. The software is protected by HASP device.
When you install the VVD on my new operating system, at the end of the installation, an error message comes up with the title "ADVAPI32.dll" followed with a red circle with a white "x" mark and text "the entry point of procedure not found in the dll."
According to the Publisher of the software, the program is running (and install) free disorder on many machines x 64 Win7 so there must be something special on my PC.
Shoul, I try to replace the file? How do I do that?
Any help is greatly appreciated.
Hello.
I just did a clean boot and tried to install the software. I got the same message: "the procedure not found in the dll entry point." This message appears at the end of the installation during "update system configuration. Please wait. »
I don't think that I have no viruses. I run Microsoft Security Essentials on my machine. In addition, installation also failed on two other Win7 computers with the same message. I tried to install the software in all kinds og compatibility modes but keep getting the same exact message. Is there another way/method I could use to isolate the problem?
The problem is now resolved after SafeNet has released a new version og the pilot.
Thank you for the effort.
-
Fractured block found during the backup of the data file
Hello
Version: 10.2.0.3
I take backups RMAN and export of db every night. The following error is recorded in the file alertlog while taking rman full backup. Also, the backup is very slow and it worked at 18hrs now (200 GB db size). Could someone please explain this to me that this error on and the action to take to solve this problem? Thank you
Kill Mar 3 20:21:52 2009
A hexadecimal dump (file 16, block 490151) in file /opt/oracle/admin/hol/udump/holiday_ora_11507.trc trace
Corrupt block relative s/n: 0x04077aa7 (16, block 490151 file)
Fractured block found during the backup of the data file
Bad block data:
type: 2 format: 2 rdba: 0x04077aa7
last change the SNA: following 0x0013.830b4809: 0 x 4 flg: 0x04
spare1: 0 x 0 spare2: 0 x 0 spare3: 0x0
consistency in tail value: 0 x 10340201
check the value in the block header: 0x7e2e
checksum calculated block: 0 x 361
Review of blocknum = 490151, file=/opt/oracle/oradata/hol/undotbs03.dbf. found valid dataThe problem may occur when the data being backed up file is simultaneously and widely used. It does not necessarily mean there is really block corruption. And in your case it seems that all is well:
Review of blocknum = 490151, file=/opt/oracle/oradata/hol/undotbs03.dbf. found valid data
On metalink:
A broken block Messages in the Alert.log during RMAN of Datafile backup
DOC - ID: 199933.1Werner
Maybe you are looking for
-
System to disable the 59628700 key. Please help me
I don't remember my password for the life of me. Please help me! Disable the system key 59628700
-
HP Compaq dc 7800: how to get a disc to install windows vista on my Compaq dc 7800
Hello I just bought a used HP Compaq 7800 dc with windows 7 as operating system. There is a product key for Vista, but no disc. Is it possible to buy a disk via HP? Kind regards kolswadet
-
I am facing a problem to find the IP address in a string that contains the other string as items... such as letters and numbers and... (ok, I'm just messing around). in any case, the string might resemble the following "10.0.0.1 stuff, stuff, stuff
-
Windows Vista Edition Family Premium SP 2
I downloaded and want to install SP2 for my 32 bit Vista Home Premium OS. I've waited almost 2 hours and still the only thing on my BLACKthe screen is:! 0xc0190036! 379/4500 (kartika.ttf) Anyone have any suggestions? Thank you
-
I brought the mouse and it has a deadline that will kill me. It happens under autocad with the middlebutton. Is there a solution? or I can take money back guarantee?